Contents

BMW 325Ci Convertible 3 Series 2004 Owner's Manual PDF

1 of 186
1 of 186

Summary of Content for BMW 325Ci Convertible 3 Series 2004 Owner's Manual PDF

Owner's Manual for Vehicle

325Ci 330Ci

Congratulations, and thank you for choosing a BMW.

Thorough familiarity with your vehicle will provide you with enhanced control and security when you drive it. Therefore we have one request:

Please take the time to read this Owner's Manual and familiarize yourself with the information that we have compiled for you before starting off in your new BMW. The manual contains important data and instructions intended to assist you in obtaining maximum satisfaction from your BMW's unique array of advanced technical fea- tures. It also contains information on vehicle maintenance designed to enhance operating safety while simultaneously helping you to maintain your BMW's value throughout an extended service life. For additional information refer to the supple- mental manuals.

This Owner's Manual should be considered a permanent part of this vehicle. It should stay with the vehicle when sold to provide the next owner with important operating, safety and maintenance information.

We wish you an enjoyable driving experience.

BMW AG

4

Notes

2003 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. Order No. 01 41 0 157 599 US English VIII/03 Printed in Germany Printed on environmentally friendly paper, bleached without chlorine, suitable for recycling.

About this Owner's Manual

We have made every effort to ensure that you are able to find what you need in this Owner's Manual as quickly as possible. The fastest way to find spe- cific topics is by using the detailed index at the end. If you wish to gain an initial overview of your vehicle, you will find this in the first chapter.

Should you wish to sell your BMW at some time in the future, please remem- ber to hand over this Owner's Manual to the new owner; it is an important part of the vehicle.

Additional sources of information

If you have any additional questions, your BMW center will be glad to advise you.

You can find more information about BMW, for example on its technology, on the Internet at www.bmw.com.

Symbols used

Indicates precautions that must be followed precisely in order to

avoid the possibility of personal injury and serious damage to the vehicle.

Contains information that will assist you in gaining the optimum

benefit from your vehicle and enable you to care more effectively for your vehicle.

Refers to measures that can be taken to help protect the environ-

ment.

Marks the end of a specific item of information.

Indicates special equipment, coun- try-specific equipment and optional extras when available.

Vehicle Memory, Key Memory, refer to page 70. Identifies func-

tions that can be specifically adapted for a particular key or vehicle. These adjustments can be performed either by yourself or by your BMW center.

5

Notes

Your individual vehicle

On purchasing your BMW, you have decided in favor of a model with individ- ualized equipment and features. This Owner's Manual describes all models and equipment that BMW offers within the same group.

We hope you will understand that equipment and features are included that you might not have chosen for your vehicle. You can easily identify any dif- ferences with the aid of the asterisk used to identify all optional equipment and accessories.

If your BMW features equipment which is not described in this Owner's Man- ual, such as a car radio or telephone, supplementary Owner's Manuals are enclosed. We ask you to read these manuals as well.

Status at time of printing

BMW pursues a policy of continuous, ongoing development conceived to ensure that our vehicles continue to embody the highest quality and safety standards combined with advanced, state-of-the-art technology. For this reason, the features described in this Owner's Manual could differ from those in your vehicle. Nor can errors and omissions be entirely ruled out. You are therefore asked to appreciate that no claims can be recognized on the basis of the data, illustrations or descriptions in this Owner's Manual.

For your own safety

Fuels

Use unleaded gasoline only. Fuels containing up to and including

10% ethanol or other oxygenates with up to 2.8% oxygen by weight that is, 15% MTBE or 3% methanol plus an equivalent amount of co-solvent will not void the applicable warranties respecting defects in materials or work- manship. Field experience has indi- cated significant differences in fuel quality volatility, composition, addi- tives, etc. among gasolines offered for sale in the United States and Canada. The use of poor-quality fuels may result in driveability, starting and stalling problems, especially under certain environmental conditions, such as high ambient temperature and high altitude. Should you encounter driveability prob- lems which you suspect could be related to the fuel you are using, we recommend that you respond by switching to a recognized high-quality brand. Failure to comply with these recom- mendations may result in unscheduled maintenance. Obey all applicable safety rules when handling gasoline.<

6

Notes

Maintenance and repair

Advanced technology, e.g. the use of modern materials and high-

performance electronics, requires spe- cially adapted maintenance and repair methods. Therefore, only have corre- sponding work on your BMW carried out by a BMW center or a workshop that works according to BMW repair procedures with correspondingly trained personnel. If work is carried out improperly there is a danger of conse- quential damage and the related safety risks.<

Parts and accessories

Important safety information! For your own safety, use genuine

parts and accessories approved by BMW. When you purchase accessories tested and approved by BMW and Original BMW Parts, you simultaneously acquire the assurance that they have been thor- oughly tested by BMW to ensure opti- mum performance when installed on your vehicle. BMW warrants these parts to be free from defects in material and workman- ship. BMW will not accept any liability for damage resulting from installation of parts and accessories not approved by BMW. BMW cannot test every product on the market to determine whether it can be used on a BMW safely and without risk to either the vehicle, its operation, or its occupants. Original BMW Parts, BMW Accessories and other products approved by BMW, together with professional advice on using these items, are available from all BMW centers. Installation and operation of non-BMW approved accessories such as alarms, radios, amplifiers, radar detectors,

wheels, suspension components, brake dust shields, telephones including operation of any portable cellular phone from within the vehicle without using an externally mounted antenna or trans- ceiver equipment, such as a CB, walkie-talkie, ham radio or similar accessories, may cause extensive dam- age to the vehicle, compromise its safety, interfere with the vehicle's elec- trical system or affect the validity of the BMW Limited Warranty. Contact your BMW center for additional information. Do not use key or remote control to lock doors or luggage compartment with anyone inside the vehicle. Refer to the Owner's Manual for more details.<

Maintenance, replacement, or repair of the emission control

devices and systems may be performed by any automotive repair establishment or individual using any certified auto- motive part.<

Symbol on vehicle parts

Indicates that you should consult the relevant section of this

Owner's Manual for information on a particular part or assembly.

7

Notes

Service and warranty

This manual is supplemented by a Ser- vice and Warranty Information Booklet for US models or a Warranty and Ser- vice Guide Booklet for Canadian mod- els.

We recommend that you read this pub- lication thoroughly.

Your BMW is covered by the following warranties:

>

New Vehicle Limited Warranty

>

Rust Perforation Limited Warranty

>

Federal Emissions System Defect Warranty

>

Federal Emissions Performance War- ranty

>

California Emission Control System Limited Warranty.

Detailed information about these war- ranties is listed in the Service and War- ranty Information Booklet for US mod- els or in the Warranty and Service Guide Booklet for Canadian models.

Reporting safety defects

The following only applies to vehicles owned and operated in the US.

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National High- way Traffic Safety Administration NHTSA in addition to notifying BMW of North America, LLC, P.O. Box 1227, Westwood, New Jersey 07675-1227, telephone toll-free 1-800-831-1117.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in indi- vidual problems between you, your dealer, or BMW of North America, LLC.

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 or 366-0123 in the Washington, D.C. area, or write to: NHTSA, U.S. Department of Transpor- tation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.

Contents

N o

te s

About this Owner's Manual 4 Additional sources of

information 4 Symbols used 4 Your individual vehicle 5 Status at time of printing 5 For your own safety 5 Symbol on vehicle parts 6 Service and warranty 7 Reporting safety defects 7

O ve

rv ie

w

Cockpit 14 Instrument cluster 16 Indicator and warning lamps 18 Buttons in steering wheel* 22 Hazard warning triangle* 23 First-aid kit* 23 Refueling 24 Fuel specifications 25 Tire inflation pressure 25

C o

n tr

o ls

a n

d f

e at

u re

s

Opening and closing:

Keys 30 Central locking system 30 Opening and closing via the

remote control 31 Opening and closing via the

door lock 33 Opening and closing from the

inside 34 Luggage compartment lid 35 Luggage compartment 37 Alarm system* 38 Electric power windows 40 Manual convertible top 41 Fully-automatic convertible

top* 46 Wind deflector* 50

To adjust:

Safe seating position 52 Seats 53 Adjusting electric power

seats 53 Lumbar support* 54 Head restraints 54 Entering the rear 55 Safety belts 56 Seat and mirror memory* 57 Seat heating* 58 Steering wheel 59 Mirrors 59

Contents

9

Passenger safety systems:

Airbags 61 Transporting children safely 64 Rollover protection system 68 Vehicle Memory, Key

Memory 70

Driving:

Ignition lock 71 Starting the engine 71 Switching off the engine 73 Parking brake 73 Manual transmission 74 Sequential manual gearbox

SMG* 75 Automatic transmission with

Steptronic* 79 Turn signal indicator/Headlamp

flasher 82 Washer/wiper system/Rain

sensor* 83 Cruise control* 84

Everything under control:

Odometer 86 Tachometer 86 Energy control 86 Fuel gauge 87 Engine coolant temperature

gauge 87 Service interval display 88 Check Control 88 Clock 89 Computer 90

Technology for safety and driving convenience:

Park Distance Control (PDC)* 92 Dynamic Stability Control

(DSC) 93 Flat Tire Monitor* 94 Brake force display 96

Lamps:

Parking lamps/Low beams 97 Adaptive headlights* 98 Instrument lighting 98 High beams/Standing lamps 99 Fog lamps 99 Interior lamps 100

Controlling the climate for pleasant driving:

Air conditioning 102 Automatic climate control* 106

Interior conveniences:

Glove compartment 111 Integrated universal remote

control* 112 Storage compartments 114 Cellular phone* 115 Ashtray, front* 115 Ashtray, rear* 116

Loading and transporting:

Ski bag* 117 Cargo loading 118 Roof-mounted luggage rack for

the hardtop* 121

C o

n tr

o ls

a n

d f

e at

u re

s

Contents

O p

e ra

ti o

n , m

ai n

te n

an c

e

Special operating instructions:

Break-in procedures 124 General driving notes 125 Antilock Brake System

(ABS) 125 Brake system 126 Hardtop* 127

Wheels and tires:

Tire inflation pressure 129 Tire condition 129 Tire replacement 130 Wheel and tire

combinations 132 Winter tires 132

In the engine compartment:

Hood 134 Engine compartment

essentials 136 Washer fluid 138 Engine oil 138 Coolant 140 Brake fluid 141

Maintenance:

The BMW Maintenance System 142

Laws and regulations:

California Proposition 65 warning 143

OBD interface socket 143

O w

n e

r se

rv ic

e p

ro c

e d

u re

s

Replacement procedures:

Onboard tool kit 148 Windshield wiper blades 148 Lamps and bulbs 149 Changing a wheel 153 Run Flat tires* 156 Battery 157 Fuses 157

Giving and receiving assistance:

Receiving assistance 158 Jump-starting 159 Towing the vehicle 160

T e

c h

n ic

al d

at a

Engine data 166 Dimensions 167 Weights 168 Capacities 169

Contents

11

In d

e x

Everything from A to Z 172

12

13

Overview

Controls and features

Operation, maintenance

Owner service procedures

Technical data

Index

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

14

Cockpit

15

1 Parking lamps/Low beams 97

2 >

Turn signal indicators 82 >

Standing lamps 99 >

High beams 99 >

Headlamp flasher 82 >

Computer 90

3 Washer/wiper system/Rain sensor 83

4 Hazard warning flashers

5 Central locking system 30

6 >

Initiating an emergency call 158 >

Mobile Service 158

7 Rear window defroster 104, 109

8 Horn: the entire surface

9 Adjusting the steering wheel 59

10 Fog lamps 99

Cockpit

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

16

Instrument cluster

17

1 Fuel gauge 87

2 Indicator lamp for turn signals 20

3 Speedometer

4 Indicator and warning lamps 18 to 21

5 Tachometer and Energy Control 86

6 Engine coolant temperature gauge 87

7 Indicator and warning lamps 18 to 21

8 Control button for >

Clock 89 >

Units of measure for exterior tem- perature display 90

9 Selector lever and program display for automatic transmission/sequen- tial manual gearbox SMG 19, 75, 81

10 Display for >

Trip odometer/Odometer 86 >

Clock 89 >

Service interval 88 >

Computer 90

11 Check Control 88

12 Trip odometer, reset to zero 86

13 Indicator and warning lamps 18 to 21

Instrument cluster

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

18

Indicator and warning lamps

Technology that monitors itself

Indicator and warning lamps that are identified by

are tested for proper functioning whenever the ignition key is turned. They each light up once for dif- ferent periods of time.

If a fault should occur in one of these systems, the corresponding lamp does not go out after the engine is started, or it lights up while the vehicle is moving. You will see how to react in the follow- ing section.

Red: stop immediately

Battery charge current

The battery is no longer being charged. Indicates a defective

alternator drive belt or a problem with the alternator's charge circuit. Please contact the nearest BMW center.

If the drive belt is defective, stop and switch off the engine immedi-

ately to prevent overheating and seri- ous engine damage. If the drive belt is defective, increased steering effort is also required.<

Engine oil pressure

Stop the vehicle immediately and switch off the engine.

Check the engine oil level; top off as required. If the oil level is correct: please contact the nearest BMW cen- ter.

Do not continue driving, as the engine could sustain serious dam-

age from inadequate lubrication.<

Flat Tire Monitor

In addition, an acoustic signal is sounded: there is a flat tire.

Reduce speed and carefully come to a stop. Avoid sudden braking and steer- ing maneuvers. For additional information: refer to page 94

Brake warning lamp

If the lamp comes on when the parking brake is not engaged:

check the brake fluid level. Before driv- ing further, be sure to comply with the instructions on pages 126 and 141.

Brake warning lamp for Cana- dian models.

Red: an important reminder

Brake warning lamp Comes on when the parking brake is engaged an additional

acoustic signal sounds when you start off. For additional information: refer to page 73

Brake warning lamp for Cana- dian models.

Lock backrest/Fasten safety belts

Comes on together with an acoustic signal until the safety belts are fastened. Flashes if the backrest is not locked. For additional information on locking the seat backrests, refer to page 55 For additional information on safety belts: refer to page 56

Airbags

Please have the system inspected at your BMW center.

For additional information: refer to page 61

19

Red and yellow: continue driving cautiously

The brake warning lamp comes on together with the yellow indi- cator lamps for ABS

and DSC: The entire ABS, CBC and DSC control system has failed. Con- tinue driving cautiously and defensively. Avoid full brake

applications. Please have the system checked by your BMW center as soon as possible. Additional information beginning on page 93

CBC, ABS and DSC and DBC indicator and warning lamps for Canadian models.

Orange: consult the nearest BMW center

Automatic transmission/sequen- tial manual gearbox The respective transmission has

responded to a malfunction by reverting to operation in its emergency default program. Please consult the nearest BMW center. For additional information: refer to page 77, 79

Yellow: check as soon as possible

Engine oil level If the lamp comes on during normal vehicle operation: the

engine oil level has fallen to the abso- lute minimum; refill as soon as possible. Do not drive more than approx. 30 miles/50 km before refilling. For additional information: refer to page 138

Engine oil level Comes on after the engine has been switched off: add engine

oil at the earliest opportunity, such as the next time you stop to refuel. For additional information: refer to page 138

Brake pads

Have the brake pads checked. For additional information: refer

to page 126

Flat Tire Monitor

The Flat Tire Monitor is malfunc- tioning or out of order. Have the

system checked by your BMW center. For additional information, refer to page 94

Dynamic Stability Control (DSC)

Indicator lamp flashes: The system is actively regulating drive torque and braking force. The indicator lamp stays lit: DSC has been switched off with the button; DTC is operational. Please contact a BMW center in case of a malfunction. Additional information beginning on page 93

Dynamic Stability Control (DSC) and brake warning lamp

The indicator lamps remain on: DSC/DTC have been switched off with the button or are faulty. Please consult the nearest BMW

center. Additional information beginning on page 93

Indicator and warning lamps

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

20

DSC indicator and brake warn- ing lamps for Canadian models.

Dynamic Brake Control (DBC)

Malfunction in DBC system. Conventional braking efficiency

is available and unrestricted. Have the system repaired at your BMW center as soon as possible. For additional information: refer to page 125

Dynamic Brake Control (DBC) warning lamp for Canadian models.

Add washer fluid The washer fluid is too low. Top off the fluid at the earliest

opportunity. For additional information: refer to page 138

SERVICE ENGINE SOON

If the indicator lamp comes on either continuously or intermit-

tently, this indicates a fault in the emis- sions-related electronic systems.

Although the vehicle remains opera- tional, you should have the systems checked by your BMW center at the earliest possible opportunity. For additional information: refer to page 143

Service Engine Soon indicator lamp for Canadian models.

Engine electronics

There is a fault in the electronic engine-management system.

You can continue to drive with reduced engine output or engine speed. Please have the system inspected at your BMW center.

Add coolant The coolant level is too low. Add coolant at the earliest opportu-

nity. For additional information: refer to page 140

CHECK GAS CAP*

This indicator lamp comes on when the gas cap is loose or

missing. Close the gas cap tightly: refer to page 24

Rollover protection system

The rollover protection system has been deactivated due to a

malfunction. Please have the system inspected by your BMW center at the earliest opportunity. For additional information: refer to page 68

Green: for your information

Turn signal indicator Flashes when the turn signal is operated.

Rapid flashing indicates a system mal- function. For additional information: refer to page 82

Cruise control Lights up when the cruise con- trol is activated: ready for oper-

ation via the buttons in the steering wheel. For additional information: refer to page 84

Front fog lamps Lights up whenever you switch on the fog lamps.

For additional information: refer to page 99

Indicator and warning lamps

21

Blue: for your information

High beams Comes on when the high beams are on or the headlamp flasher

is actuated. For additional information: refer to pages 82, 99

Indicator and warning lamps

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

22

Buttons in steering wheel*

These buttons let you operate the fol- lowing functions quickly and without being distracted from traffic conditions:

>

Selected radio functions >

The cruise control >

Selected telephone functions.

The controls are active only when the corresponding systems and

accessories are switched on.<

Press briefly:

Receive a phone call, initiate dialing, terminate a call.

Switch between phone, radio, cassette and CD.

Forward:

>Radio Press briefly: next station in station memory Extended pressure: station search

>CD Press briefly: jump to next track Extended pressure: search function in track

>Cassette Press briefly: jump to next track or stop fast forward Extended pressure: fast forward

>Phone Scan personal phone book.

Rewind/reverse: same functions as for- ward.

Volume.

Cruise control: select a stored setting.

Cruise control: store and accelerate + or decelerate and store .

Cruise control: activate/interrupt/deac- tivate.

23Hazard warning triangle*

The hazard warning triangle is stored in the luggage compartment lid inside the container for the onboard tools.

To open the container, loosen the wing nut.

Always observe all legal regula- tions requiring a warning triangle

to be carried in the vehicle.<

First-aid kit*

The first-aid kit is located under the passenger seat.

To open: pull the handle and fold the cover down.

To close: fold the cover up and press it until the tab engages.

Some of the articles in the first-aid kit have a limited period of use

before expiration. For this reason, check the expiration dates of each of the items regularly and replace any whose expiration dates have passed. You can purchase replacements in any drugstore or pharmacy. in any drug- store or pharmacy. Always observe all legal regulations requiring a first-aid kit to be carried in the vehicle.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

24 Refueling

Fuel filler door Always switch off the engine before refueling, as it is not possi-

ble to add fuel with the engine running, and attempts may also trigger the SERVICE ENGINE SOON lamp.<

Press on the rear edge of the fuel filler door to open and close it.

Pull the knob with the fuel pump sym- bol, located on the right side wall of the luggage compartment.

Always observe all safety precau- tions posted at the service station

when handling fuel. Never carry spare fuel containers in your vehicle. Whether empty or full, these containers can leak, cause an explosion, or lead to fire in the event of a collision.<

Simple and environmentally friendly

Open the gas cap carefully to pre- vent fuel from spraying out. Fuel

spray may cause injury.<

Keep the gas cap in the bracket attached to the fuel filler door.

When refueling, insert the filler nozzle completely into the filler pipe. Lifting the nozzle during refueling

> results in premature pump shutoff >and will reduce the effectiveness of

the vapor recovery system on the pump.

The fuel tank is full when the filler noz- zle shuts off the first time.

25

Close the gas cap carefully after refueling until a click is heard.

While closing, be sure not to squeeze the strap which is fastened to the cap. A loose or missing cap will activate the CHECK GAS CAP* lamp.<

Fuel tank capacity >Approx. 16.6 gal./63 liters, of which >approx. 2.1 gal./8 liters are reserve

capacity.

Do not drive to the last drop of fuel. This can prevent the engine

from operating properly and result in damage.<

Fuel specifications

The engine uses lead-free gasoline only.

Required fuel:

>Premium Unleaded Gasoline, min. 91 AKI. AKI = Anti Knock Index

Never use leaded fuel, as it would cause permanent and irreversible

damage to the oxygen sensor and the catalytic converter.<

Tire inflation pressure

Checking tire pressures Tire pressures in psi/kilopascal are shown on the driver's door post and are visible when the door is open.

Only check the tire inflation pressures of cold tires. This means after driving a maximum of 1.25 miles/2 km or after the vehicle has been parked for at least 2 hours. Warm tires have higher infla- tion pressures.

In the following tire inflation pressure table, all pressures are specified in the standard units of pressure, psi and kilo- pascal, and apply to cold tires, i.e. tires at ambient temperature.

Refueling

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

26

Vehicles with Flat Tire Monitor:

After correcting the inflation pressures, reinitialize the system. Refer to page 94.

Check the tire pressures on a reg- ular basis at least twice a month

and before every extended journey. If this is not done, incorrect tire pressures can cause driving instability and tire damage, ultimately resulting in acci- dents. Remember to check the inflation pres- sure in the space-saver or standard spare tire. Inflate the spare tire to the highest infla- tion pressure specified for your vehi- cle.<

Comply with tire approval specifications The inflation pressures in the table apply to BMW approved tire sizes and tire manufacturers. Your BMW center can provide you with more information about these. Other pressures may be required for tires made by other manu- facturers.

Your vehicle is equipped with tires that not only meet US standards, but also European standards. We recommend the exclusive use of BMW approved tires.

Tire inflation pressure

27

BMW Tires All pressure specifications in the table are indicated in psi/kilopascal with cold tires cold = ambient temperature

325Ci 205/55 R 16 91 H M+S 205/55 R 16 91 H 225/50 R 16 92 W 225/45 R 17 91 W

29/200 33/230 36/250 44/300

225/45 ZR 17 245/40 ZR 17

29/200

33/230

36/250

44/300

205/50 R 17 93 V M+S extra load 205/50 R 17 93 W extra load 205/55 R 16 91 Q M+S 225/50 R 16 92 Q M+S 205/50 R 17 93 Q M+S extra load 225/45 R 17 91 Q M+S

32/220 36/250 39/270 46/320

330Ci 225/45 R 17 91 W 32/220 36/250 39/270 46/320

225/45 ZR 17 245/40 ZR 17 225/40 ZR 18 255/35 ZR 18

32/220

32/220

36/250

36/250

39/270

39/270

46/320

46/320

205/50 R 17 93 V M+S extra load 205/50 R 17 93 W extra load 205/50 R 17 93 Q M+S extra load 225/45 R 17 91 Q M+S

32/220 36/250 39/270 46/320

All Space-saver spare tire 61/420

Tire inflation pressure

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

28

29

Overview

Controls and features

Operation, maintenance

Owner service procedures

Technical data

Index

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

30

Opening and closing

Keys

The key set 1 Master keys with remote control unit

these keys determine the functions of the Key Memory. Refer to page 70. You can mark the individual keys for subsequent identification by apply- ing the colored decals that you received when accepting delivery of your vehicle

In every master key with the remote control feature there is an

extended-life battery that is charged automatically in the ignition lock as you drive. For this reason, if you have master keys with the remote control feature that are not being used otherwise, use those keys at least once a year while driving for an extended period to charge the battery.<

2 Spare key for storage in a safe place, such as in your wallet. This key is not intended for constant use. The luggage compartment lid and the glove compartment cannot be locked and unlocked with this key. This is useful for valet parking, for example

Central locking system

The concept The central locking system engages and releases the following locks at the same time:

>doors > luggage compartment lid > fuel filler door >glove compartment.

The central locking system is ready for operation whenever the driver's door is closed.

The central locking system can be operated

> from outside via the door lock as well as via the remote control

> from inside by pressing a button.

The fuel filler door is not locked when the central locking system is activated from the inside, refer to page 34.

When the system is actuated from the outside, the anti-theft system is also activated. This prevents the doors from being unlocked via the lock buttons or the release handle. The alarm system is also activated or deactivated.

The central locking system is automati- cally deactivated in the event of an accident. In addition, the hazard warn- ing flashers and interior lamps come on.

31Opening and closing via the remote control

The concept The remote control also provides two additional functions beyond the central locking feature:

>To switch on interior lamps, refer to page 32. With this function you can also search for the vehicle when parked in an underground garage, for instance

>To open the luggage compartment lid, refer to page 32. The luggage compartment lid will open slightly, regardless of whether it was previously locked or unlocked.

Whenever you unlock or lock the vehi- cle, you simultaneously deactivate/acti- vate the anti-theft system, disarm/arm the alarm system and switch the interior lamps on/off.

You can have a signal set to con- firm that the vehicle's locks have

engaged securely.<

Master keys with remote control Persons or animals inside the vehicle may be able to lock the

doors from the inside. For this reason, you should always take the vehicle keys with you so that the vehicle can be opened again from the outside at any time.<

If it is no longer possible to lock the vehicle via the remote control,

the battery is discharged. Use this key while driving for an extended period in order to recharge the battery. To prevent unauthorized use of the remote control, surrender only the spare key when leaving the vehicle for valet parking, for example. In the event of a system malfunction, please contact your BMW center. You can also obtain replacement keys there.<

1 Unlock, convenience opening mode, and disarm alarm system

2 Lock and secure, arm alarm system, activate interior lamps, disarm tilt alarm sensor and interior motion sen- sor

3 Open the luggage compartment lid, Panic mode trigger alarm

To release

Press the button once to unlock the driver's door.

Press the button a second time to disengage all vehicle locks.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

32

Convenience opening mode* Press and hold button. The electric power windows and the fully-automatic convertible top open.

To lock and secure

Press the button.

To switch on the interior lamps

With the vehicle locked, press the but- ton.

To deactivate the tilt alarm* and interior motion sensors*

Press the button a second time imme- diately after locking.

For additional information, refer to page 39.

To open the luggage compartment lid

Press the button.

The luggage compartment lid will open slightly, regardless of whether it was previously locked or unlocked.

If the luggage compartment lid was locked, it will be locked again

after it is reclosed. Before and after a trip, be sure that the luggage compartment lid has not been opened unintentionally.<

Panic mode trigger alarm

Provided that the alarm system is armed, you can respond to imminent danger by holding down the button for more than seconds.

To switch off the alarm:

Press the button.

External systems The remote control system's operation may be affected by other units or equipment operating in the immediate vicinity of your vehicle.

If this should occur, you can still open and close the vehicle using the master key in either the door or luggage com- partment lid locks.

For US owners only The transmitter and receiver units com- ply with part 15 of the FCC Federal Communications Commission regula- tions. Operation is governed by the fol- lowing:

FCC ID:

>LX8EWS >LX8FZVS >LX8FZVE.

Compliance statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

>This device may not cause harmful interference

>This device must accept any interfer- ence received, including interference that may cause undesired operation.

Any unauthorized modifications to these devices could void the

user's authority to operate the equip- ment.<

Opening and closing via the remote control

33Opening and closing via the door lock

One turn of the key in the driver's door lock unlocks the driver's door, the fuel filler door and the glove compartment. Turning the key a second time unlocks the passenger-side door and the lug- gage compartment lid.

You can have a signal set to con- firm that the vehicle's locks have

engaged securely.<

Convenience operation You can also operate the power win- dows and the fully-automatic convert- ible top via the door lock.

>To open: with the door closed, hold the key in the Unlock position

>To close: with the door closed, hold the key in the Lock position.

Whenever closing the windows or sliding/tilt sunroof you should

always monitor their path and progress to ensure that no one is injured. Releas- ing the key stops the operation.<

Manual operation In the event of electrical malfunction

Turn the key all the way to the left or right to unlock or lock the driver's door.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

34 Opening and closing from the inside

You can use this button to control the central locking system whenever the doors are closed. The doors and lug- gage compartment lid are unlocked or locked only. The anti-theft system is not activated.

If only the driver's door was unlocked from the outside and

you press the button, then, with the driver's door still open, the passenger- side door, the luggage compartment lid, the fuel filler door and the glove compartment will unlock, too. If the driver's door is closed, it will be locked.<

If you desire, the central locking system can be activated automati-

cally as soon as you begin to drive. This can be adjusted to be key-specific.<

To unlock and open the doors 1. Press the button for the central lock-

ing system 2. Pull the release handle above the

armrest on the door you wish to open

or

pull the release handle for any door twice: to unlock and open the door.

To lock >Either use the central locking button

to lock both doors at once or >press down the individual door lock

buttons. In this case, the fuel filler door will stay unlocked. To prevent the driver from being inadvertently locked out of the vehicle, the driver's door lock button will not engage as long as the door is open.

Persons or animals inside the vehicle may be able to lock the

doors from the inside. You should always take the vehicle's keys with you so that you can open the vehicle again from the outside at any time.<

35Luggage compartment lid

The lock Only the master keys fit in the lock for the luggage compartment lid, refer to page 30.

To secure separately Lock the glove compartment using the master key.

This locks the luggage compartment lid and disconnects it from the central locking system. This feature can be used to prevent unauthorized access to the luggage compartment when you surrender the spare key only, refer to page 30. This can be advantageous for valet parking, for example.

To open from the outside Press the button in the handle recess: the luggage compartment lid opens slightly.

The luggage compartment is lit when the luggage compartment lid is opened.

Manual operation In the event of electrical malfunction

Turn the master key all the way to the left the luggage compartment lid will open slightly.

The luggage compartment is locked again as soon as you close the lid.

To open from the inside* If the luggage compartment lid has not been locked separately, you can open it with this button in the footwell on the driver's side when the vehicle is sta- tionary.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

36

To close The handle recesses in the interior trim panel of the luggage compartment lid make it easier to pull the lid down.

To avoid injuries, be sure that the travel path of the luggage com-

partment lid is clear when it is closed, following the same precautions as with all closing procedures.<

Operate the vehicle only when the luggage compartment lid is

closed. Otherwise, exhaust fumes could penetrate the interior of the vehi- cle. <

Should it be absolutely necessary to operate the vehicle with the luggage compartment lid open, with closed con- vertible top:

1. Close all windows 2. Greatly increase the quantity of air

coming from the air conditioning or automatic climate control system, refer to page 102 or 106.

Emergency release This lever releases the luggage com- partment lid from inside the luggage compartment.

Luggage compartment lid

37Luggage compartment

To fold up and secure the floor panel 1. Pull up at the handle and fold the

panel up 2. Press the button to release the

hanger from the handle

3. Hook the handle into the rubber seal of the drip rail.

Carefully replace the hanger in its holder when lowering the floor

panel back down.<

The fittings at the corners of the lug- gage compartment provide you with a convenient means of attaching luggage compartment nets* and flexible straps for securing luggage.

Refer also to Cargo loading on page 118.

To enlarge the luggage compartment With the convertible top closed, you can enlarge the luggage compartment. To do this, flip the handle outward and press it down and toward the front of the vehicle. The convertible top com- partment panel is now raised and secured.

To fold down the convertible top compartment panel The convertible top compartment lid must be folded down to open the con- vertible top. Swing out the handle and pull toward the back of the vehicle.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

38

Before lowering the convertible top, refer to page 41 or 46, always

check to ensure that the luggage com- partment panel is folded down. Other- wise damage could occur.<

Alarm system*

The concept The vehicle alarm system responds:

>When a door, the hood or the lug- gage compartment lid is opened

>To movements inside the vehicle interior motion sensor

>To variations in the vehicle's tilt angle such as those occurring during attempts to steal the wheels or tow the vehicle tilt alarm sensor

>To interruption of battery voltage.

The system responds to unauthorized vehicle entry and attempted theft by simultaneously activating the following:

>The acoustic alarm sounds for 30 seconds

>The hazard warning flashers are acti- vated for approx. five minutes

>The high beams flash on and off in rhythm with the hazard warning flash- ers.

To arm and disarm the alarm system When the vehicle is locked or unlocked via the driver's door lock or with the remote control, the alarm system is also simultaneously armed or disarmed.

You can have different acknowl- edgment signals set to confirm

arming and disarming.<

You can open the luggage compart- ment lid when the system is armed by pressing the remote control button, refer to page 32. The lid is once again secured when it is closed.

Extended pressure on the button sets off the alarm Panic mode, refer to page 32.

Luggage compartment

39

Indicator lamp displays >The indicator lamp below the interior

rearview mirror flashes continuously: The system is armed

>The indicator lamp flashes during arming: the door(s), the hood or the luggage compartment lid are not completely closed. Even if you do not close the alerted area(s), the remain- ing areas are secured, and the indi- cator lamp will flash continuously after 10 seconds. However, the inte- rior motion sensor is not activated

>The indicator lamp goes out when the system is disarmed: no manipulation or attempted intrusions have been detected in the period since the sys- tem was armed

>The indicator lamp flashes for 10 seconds when the system is dis-

armed: an attempted entry has been detected in the period since the sys- tem was armed.

Following triggering of an alarm, the indicator lamp will flash continuously.

Avoiding unintentional alarms The tilt alarm sensor and interior motion sensor may be switched off at the same time. You can do this to prevent a false alarm from being triggered in garages with elevator ramps, for instance, or when the vehicle is transported by train:

Lock the vehicle twice to arm the sys- tem. Press the button on the remote control twice in succession or lock the vehicle twice with the key.

The indicator lamp lights up briefly and then flashes continuously. The tilt alarm sensor and the interior motion sensor are deactivated as long as the system is armed.

You can have the tilt alarm sensor and the interior motion sensor

permanently deactivated.<

Interior motion sensor* Deactivate the interior motion sensor refer to Avoiding unintentional alarms if persons or animals are to remain in the vehicle.

The system deactivates the tilt- alarm sensor and the interior

motion sensor if the convenience clos- ing of windows is interrupted in the first 10 seconds and then restarted. The alarm must then be disarmed and reac- tivated before it will resume opera- tion.<

Alarm system*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

40 Electric power windows

To open and close windows When leaving the vehicle, always remove the ignition key from the

lock and remember to close the doors to prevent children from operating the power windows and injuring them- selves, etc.<

With the ignition key in position 1 or higher

>Press the switch until you feel resis- tance: the window retracts as long as you maintain pressure on the switch

>Press the switch briefly past the pres- sure point: the windows move auto- matically. Pressing the switch again stops the opening cycle.

You can close the windows in the same manner by pulling the switch. The rear windows do not close automatically.

To operate all the side windows With the ignition key in position 1 or higher

>Press the switch until you feel resis- tance: the windows retract as long as you maintain pressure on the switch

>Press the switch briefly past the pres- sure point: the windows move auto- matically. Pressing the switch again stops the opening cycle.

You can close all windows in the same manner by pulling the switch. The win- dows cannot be closed automatically using this switch.

For convenience operation via the remote control or the door lock, refer to page 32 or 33.

41

After the ignition has been switched off You can still use the electric power win- dows for up to 15 minutes, as long as no one opens any of the doors.

Safety feature If the closing force of a front window exceeds a certain value as the window is being closed, the closing procedure is immediately interrupted and the win- dow opens again slightly.

Despite this protective function, you must still make sure that there

are no obstacles within the closing range of the windows. Otherwise, it cannot be guaranteed that the closing procedure will be interrupted in certain cases, e.g. when very thin objects are in the closing range. This protective function is deactivated when the switch is pulled past the resistance point and held there.<

After power loss After the battery has been discon- nected, the protective function must be reinitialized. Please refer the problem to your BMW center.

Manual convertible top

The fabric top offers the perfect protec- tion against weather and one person can open and close it easily and simply.

To gain maximum satisfaction from your convertible, please observe the follow- ing: we strongly recommend that you close the convertible top before leaving the vehicle parked. When closed, the top not only guards the passenger compartment from unforeseeable dam- age from the weather, but also affords a degree of protection against theft.

However, even when the top is closed valuables should always be stored in the locked luggage compartment.

Never attempt to mount any kind of roof rack or luggage carrier on the convert- ible top.

Closing the electric power win- dows: to help ensure that the win-

dows seal securely, you should either close the rear windows first or close all four windows at the same time.<

Electric power windows

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

42

To open the convertible top Never attempt to open or close the convertible top unless the

vehicle is completely stationary. To pre- vent vehicle damage the top compart- ment lid's lock will not disengage unless the luggage compartment lid is closed.<

1. Flip the locking handle out refer to illustration and turn it as far as the end stop will allow

2. Raise the convertible top a little bit, release the tension

3. To unlock, press the button with the ignition key in position 1 or higher. The top compartment lid's lock dis- engages and the lid itself rises a small distance. The side windows will lower slightly

If the indicator lamp lights up when the button is pressed, the lid

cannot be unlocked because the top compartment panel is raised, refer to page 37. Lower the top compartment panel and close the tailgate.<

Manual convertible top

43

4. Position the rear convertible top frame vertically and grip it firmly

You can make it easier to raise the rear convertible top frame by

pressing the area indicated by the arrow.<

5. Reach into the recess created when the convertible top compartment lid is lifted and pull it all the way by hand see arrow 1

6. Lay the rear convertible top frame in the convertible top compartment see arrow 2

Let go of the rear convertible top frame before laying the convert-

ible top down, otherwise, the side trim panel could be damaged.<

7. Raise the front of the top and pull it back for storage

Now finish pushing the convertible top all the way down into the con-

vertible top compartment. This makes it easier to close the convertible top com- partment lid, especially at lower tem- peratures.<

Manual convertible top

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

44

8. Press down slightly on the convert- ible top compartment lid from above see arrow. The closing process will then be carried out automatically

9. Either close the slightly lowered side windows or put them at the desired height.

Operate the convertible top com- partment lid from above only in

order to avoid any pinching. An interlock device helps avoid damage to the vehicle by preventing the lug- gage compartment lid from opening unless the convertible top compartment lid is completely closed.<

As soon as the convertible top com- partment lid closes the central locking system will release the lock to allow renewed access to the luggage com- partment.

Never store the convertible top in its compartment for more than

one day while it is wet to avoid perma- nent damage from moisture.<

To close the convertible top 1. Turn the ignition key to position 1 2. Press the button to unlock it. The

convertible top will be unlocked and the side windows will lower slightly

3. Open the convertible top compart- ment lid all the way

4. Lift the convertible top out by the lat- eral guide section see arrow 1, and the front convertible top frame see arrow 2, swinging it forward until you encounter perceptible resistance until it stops

To avoid damaging the side trim, always fold the convertible top

forward before folding the rear frame brace up into its vertical position.<

Manual convertible top

45

5. Either close the slightly lowered side windows or put them at the desired height

6. Press down slightly on the convert- ible top compartment lid from above. The top then closes automatically, refer to page 41

Operate the convertible top com- partment lid from above only in

order to avoid any pinching.<

As soon as the convertible top compartment lid closes the central

locking system will release the lock to allow renewed access to the luggage compartment.<

7. Holding on to the locking handle, pull the front part of the convertible top frame up onto the windshield frame, and lock the convertible top by turn- ing the handle until you hear the con- vertible top engage and lock.

The system automatically presses the top's rear frame against the convertible top compartment lid, pretensioning it to ensure that it seals tightly.

At higher speeds, the ensuing vacuum in the passenger com-

partment can cause the convertible top to begin fluttering. Increase the air sup- ply via the ventilation controls so that a vacuum does not occur in the vehicle.<

Position for cleaning To be able to access the convertible top compartment, lean the rear frame of the convertible top against the cover of the convertible top compartment.

First, use the button for activating the convertible top to unlock the

locks of the convertible top compart- ment. Refer to page 42.<

For additional information on vehi- cle care, refer to the Caring for

your vehicle brochure.<

Manual convertible top

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

46 Fully-automatic convertible top*

The fully-automatic convertible top combines the benefits of effective pro- tection against the elements with sim- ple and convenient operation.

To gain maximum satisfaction from your convertible, please observe the follow- ing:

>We strongly recommend that you close the convertible top before leav- ing the vehicle parked. When closed, the top not only guards the passen- ger compartment from unforesee- able damage from the weather, but also affords a degree of protection against theft. In addition, keep valu- ables only in the locked luggage compartment, even when the con- vertible top is closed

>Never mount a roof-mounted luggage rack on the convertible top

>To avoid damaging the convertible top, do not activate it at temperatures below 147/ 106.

Never store the convertible top in its compartment for more than

one day while it is wet to avoid perma- nent damage from moisture.<

Do not lay objects on the convert- ible top, as they could fall off

when it moves, causing vehicle damage or personal injury.<

Driving when the opening or clos- ing process has not been com-

pleted can cause vehicle damage or personal injury. Always keep your hands and fingers well away from the top's mechanism while it is opening and closing. Ensure that children remain at a safe distance from the top's travel range while it is in motion.<

Try to make sure that the vehicle is completely stationary before

using the fully-automatic convertible top. Otherwise the opening or closing procedure could be interrupted. If you set the convertible top in motion while the vehicle is stationary and then have to start suddenly for instance, at a traffic light you can still complete the procedure by driving as slowly as possible and again holding the corre- sponding button pressed.<

When closing the electric power windows while underway, always

remember to either start by closing the rear windows or to close all of them at once. Failure to adhere to this sequence can prevent the windows from sealing tightly at high speeds.<

At higher speeds, the ensuing vacuum in the passenger com-

partment can cause the convertible top to begin fluttering. Increase the air sup- ply via the ventilation controls so that a vacuum does not occur in the vehicle.<

47

Opening and closing 1 To close

2 To open

To avoid placing unnecessary loads on the battery, you should

avoid operating the top when the engine is switched off. Before closing the top, always ensure that the windshield frame is clear of any obstructions that could prevent the top from closing correctly.<

With the ignition key in position 1 or higher, and with the vehicle stationary

1. Read and comply with the preceding safety precautions

2. Ensure that the convertible top com- partment panel in the luggage com- partment is folded down, see page 37; otherwise, it will not be possible to open the convertible top

3. Ensure that the luggage compart- ment lid is closed

4. Maintain pressure on the corre- sponding button for the convertible top operation.

The luggage compartment lid can- not be opened while the convert-

ible top is in motion.<

While the convertible top is in motion, the rear window will move

toward the passenger compartment. To avoid possible pinching, the area around the closing convertible top should be clear.<

After having been stored for an extended period of time in the

convertible top compartment, e.g. dur- ing the winter months because the hardtop was being used, you may have to support the convertible top by hand when closing it for the first time. If the convertible top should halt just before the closing phase is completed, press against the front section of the convertible top frame from the outside to help the closing process along. Con- tinue pressing the switch while doing so until the top starts up again on its own.<

Indicator lamps >The red indicator lamp is lit whenever

the convertible top mechanism is in motion. It goes out as soon as the opening or closing operation has been completed

> If the red indicator lamp flashes after the control button is released, the convertible top has not yet been opened or closed completely. You can resume operation in the desired direction by pressing the button again

> If the yellow indicator lamp lights up continuously with the button pressed, the convertible top compartment

Fully-automatic convertible top*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

48

panel has been raised and the top cannot be moved.

The side windows move down slightly whenever the button for operating the convertible top is pressed.

They will go back up if you keep holding the button down for more than 2 seconds after the opening or closing process has been completed and the indicator lamp has gone out.

Interruption The convertible top stops moving immediately when the button is released. You can resume operation in the desired direction by pressing the button again

Do not close the side windows using the power window switches

if the convertible top has not been closed completely. Otherwise, the side windows may not seal properly with the rubber seals of the convertible top.<

If the opening or closing operation is interrupted by releasing the buttons, the convertible top remains in the respective position for 15 minutes before it slowly moves into a stable position. The operation can be contin- ued by pressing the buttons.

Do not repeatedly interrupt and resume the closing procedure, as

otherwise the fully-automatic convert- ible top mechanism could be dam- aged.<

In certain cases, the luggage compart- ment lid cannot be opened if the open- ing or closing operation has been inter- rupted.

Operate the convertible top manu- ally in emergency situations only

to avoid causing damage due to incor- rect operation.<

Convenience operation via remote control and driver's door lock Refer to pages 32 and 33.

Manual closing in the event of an electrical malfunction 1 Emergency operation

2 Allen wrench

3 Recess

Only operate the convertible top manually when closing it. Never

open it manually since the convertible top compartment lid cannot be locked, and would open while you are driving.<

Manual closing is best carried out by two persons from outside with

the driver's door open and the driver's seat folded forward. No one is to be in the rear seat while you are doing this.<

Fully-automatic convertible top*

49

1. Remove the insert between the rear seats. Take the trim off of the guide rod and flip it forward

2. Press down hard on the emergency lock 1 see previous illustration. After a brief pause, the mechanism for the convertible top compartment lid will be released

If the mechanism for the convert- ible top compartment lid does not

unlock, then insert the Allen wrench 2 into the recess 3 and turn clockwise to release it.<

3. If the luggage compartment lid is closed, open the convertible top compartment lid up as far as the stop will allow

4. Grasp the convertible top by the lat- eral guide section see arrow 1 and the front convertible top frame see arrow 2. Lift out the top and swing it forward until you encounter a perceptible resistance until it stops. Position the rear convertible top frame vertically and close the convertible top compartment lid. Fold down the rear convertible top frame

To avoid damaging the side trim, always fold the convertible top

forward before folding the rear frame brace up into its vertical position.<

5. Use a screwdriver to lift out the cover panel that is in the center of the front convertible top frame

6. Insert the Allen wrench 2 refer to page 48 into the recess see arrow

7. Pull down on the front convertible top frame as far as possible. Com- plete the closing process by continu- ing to turn the wrench in a clockwise direction. Turn until the front convert- ible top frame has locked onto the windshield frame. The system auto- matically presses the top's rear frame against the convertible top compartment lid, pretensioning it to ensure that it seals tightly.

Always make sure the closing pro- cedure is completed to prevent

vehicle damage or personal injury.<

Fully-automatic convertible top*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

50

Please consult your BMW center to have the defect corrected.<

Position for cleaning To be able to access the convertible top compartment, lean the rear frame of the convertible top against the cover of the convertible top compartment.

First, use the button for activating the convertible top to unlock the

locks of the convertible top compart- ment. Refer to page 47.<

For additional information on vehi- cle care, refer to the Caring for

your vehicle brochure.<

Wind deflector*

With the convertible top open, the wind deflector keeps air movement in the passenger compartment to a minimum, thus providing you with a pleasant drive, even at higher speeds. The wind deflector comes in a protective sleeve, and because of its slim dimensions, can be easily stored in the luggage com- partment.

Installation 1. Remove wind deflector from the pro-

tective sleeve

Fully-automatic convertible top*

51

2. Flip out both sides and lock into place. It is essential for the two com- ponents marked in the illustration to mesh at this point

3. Hold the wind deflector so that the smaller half points toward the front and guide the mounting pin for the side piece into the proper opening

4. Pull back on the mounting pin for the other side piece by using a slide, so that the mounting pin can be guided into the opening provided

5. Unlock the convertible top compart- ment lid via the convertible top con- trol button, refer to page 47, and open the convertible top compart- ment lid

6. Flip the back half of the wind deflec- tor backward, so that the mounts are lying on the vehicle

7. Close the convertible top compart- ment lid via the convertible top con- trol button. The wind deflector is now attached so that it is theft-proof.

Operate the convertible top com- partment lid from above only in

order to avoid any pinching. With the wind deflector in place: to avoid damaging the wind deflector never push the front seats all the way back.<

Removal Follow the same procedure as when installing, just reverse the steps.

Wind deflector*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

52

To adjust

Safe seating position

For driving that is relaxed and less likely to cause fatigue, you should select a sitting position that reflects your per- sonal requirements. In combination with the safety belts and airbags, the correct seating position also plays an important role in enhancing occupant safety in the event of an accident. To ensure that the vehicle's safety systems provide you with optimal protection, we request that you direct your careful attention to the following section.

For supplementary information on transporting children, refer to page 64.

Sitting safely with airbags Always maintain an adequate dis- tance between yourself and the

airbags. Always hold the steering wheel by the rim to keep any chance of injury to hands or arms to an absolute mini- mum should the airbag be deployed. Never allow any objects, individuals or animals to obstruct the areas between passengers and airbags. Never use the front airbag's cover as a storage tray or support for objects of any kind. Never allow front passengers to rest their feet or legs on the airbag cover.<

For airbag locations and additional information on airbags, refer to page 61.

Sitting safely with safety belts Your vehicle is equipped with four seats, each of which is provided with a safety belt.

Never allow more than one person to wear a single safety belt. Never

allow infants or small children to ride in a passenger's lap. Avoid twisting the belt while routing it firmly across the hips and shoulder, wear it as snugly against your body as possible. Do not allow the belt to rest against hard or fragile objects. Do not route the belt across your neck, or run it across sharp edges. Be sure that the belt does not become caught or jammed. Avoid wearing bulky clothing and pull on the lap belt periodically to retension it over your shoulders. In the event of a frontal impact, a loose lap belt could slide over your hips, leading to abdominal injury. In addition, the safety belt's restraint effectiveness is reduced if it is worn loosely. Expectant mothers should always wear their safety belts, taking care to position the lap belt against the lower hips, where it will not exert pres- sure against the abdominal area.<

For information on using the safety belts, refer to page 56.

53Seats

When adjusting your seat, always observe the following precautions

Never try to adjust your seat while operating the vehicle. The seat

could respond with unexpected move- ment, and the ensuing loss of vehicle control could lead to an accident. Never ride with the backrest reclined to an extreme angle. This is especially impor- tant for the front passenger to remem- ber. If you do so, there is a risk that you will slide under the safety belt in an accident, thus reducing the protection provided by the safety belt. With the wind deflector in place: Do not push the front seats all the way back, otherwise the wind deflector will be damaged.<

Seat adjustment >Power seat adjustment, refer to

page 53 >Head restraint, refer to page 54 >Entering the rear, refer to page 55.

Adjusting electric power seats

Seat adjustment 1 Tilt angle

2 Backward/forward adjustment

3 Height

4 Backrest angle

Please refer to the adjustment instructions on page 53 to reduce

the risk of personal injury.<

With the BMW sports seat* you can also adjust the thigh support. To do so, pull the lever and adjust the position of the cushion for thigh support as desired.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

54 Lumbar support*

To adjust You can adjust the backrest's contour for additional support in the curvature of your spine's lumbar region.

The upper hips and spinal column receive supplementary support to help you maintain a relaxed, upright posture.

>Press front/rear of switch: increase/decrease curvature

>Press the upper/lower end of the switch: increase the upper/lower cur- vature.

Head restraints

Front head restraints 1 Height

Head restraints reduce the risk of spinal injury in the event of an

accident. Adjust the head restraint so that its center is approximately at the height of your ears. When moving the head restraints up or down, avoid placing hands and fingers between the head restraint and the upper edge of the backrest to avoid the possibility of injury.<

Tilt angle: position the head restraints manually in the preferred position.

55

Rear head restraints To avoid possible violation of traf- fic laws, never retract the head

restraints unless the rear seats are empty. Always ensure that the head restraints are raised before transporting passengers in the rear seat.<

To completely lower the rear head restraints:

1. Press the button and hold it down 2. Push the head restraint down from

above.

Raising the rear head restraints Raise the head restraints until you hear them click into place.

Do not remove the rear head restraints, as this would damage

them.<

For further information, please consult your BMW center.

Do not use the rear head restraints as storage shelves.

Always keep the travel path for the roll- over protection system free and clear. Never place protective covers or similar items on the head restraints. See also the labels on the head restraints.<

Entering the rear

The seat-integrated safety belt system allows for easy access to the rear.

1. Lift lever 1 up and tilt the backrest forward

2. Press and hold button 2 in driving direction until the seat moves to the desired position

3. After entering the rear, fold back and lock the backrest

4. Press button 2 opposite the direction of travel and hold. The seat moves back into its previous position. If the button 2 is released beforehand, the seat stops in the respective position.

Head restraints

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

56

You can lock a backrest that has been tilted forward. This makes

sense when, for instance, someone is climbing into the rear on an incline. To do this, press against the backrest until you hear it click into place. To move it back into place, you do not need to first unlock it by moving the lever 1.<

Lock both backrests while driving, otherwise there is a danger of an

unexpected movement causing an accident.<

The indicator lamp in the instru- ment cluster flashes when the backrest is not locked, refer to

page 18.

Safety belts

Always wear your safety belt Always fasten your safety belt before starting off. As supplemental restraint devices, the airbags are designed to enhance the effectiveness of the safety belts, and not to replace them.

Always detach the rear safety belts from their retainers before

wearing.<

To avoid undesired movement at high speeds, always store the rear

safety belts in their retainers when they are not in use.<

To close Make sure you hear the lock engage in the belt buckle.

To release 1. Press the red button in the belt

buckle 2. Hold the belt 3. Guide the belt back into its reel.

Safety belt height The front belt system automatically adapts to your body size when the height of the head restraint is adjusted. Refer to page 54.

If the safety belt system has been subjected to the stresses involved

in an accident or otherwise damaged: have the entire safety belt mechanism replaced by your BMW center, includ- ing the safety belt tensioner. In addi- tion, have your BMW center inspect the safety belt anchors. If a child-restraint system was in the vehicle during an accident, consult the manufacturer's instructions regarding replacement.<

Entering the rear

57Seat and mirror memory*

You can store and recall three different driver's seat and exterior mirror posi- tions.

The lumbar support settings are not stored in the memory.<

To store 1. Ignition key position 1 or 2 2. Select the desired seat and exterior

mirror positions 3. Press the MEMORY button: the indica-

tor lamp in the button lights up 4. Press memory button 1, 2 or 3, as

desired: the indicator lamp goes out.

To select a stored setting Do not select a memory position while the vehicle is moving. If you

do so, there is a risk of accident from unexpected seat movement.<

Ignition key in position 1:

>Briefly press memory button 1, 2 or 3, as desired. Movement stops immediately when one of the seat-adjustment or mem- ory buttons is activated during the adjustment process.

The driver's door is closed and the igni- tion key is either removed or in position 0 or 2:

>Maintain pressure on the desired memory button 1, 2 or 3 until the adjustment process is completed.

If you press the MEMORY button acci- dentally: press the button again; the indicator lamp goes out.

You can have this feature pro- grammed so that when you use

the remote control from your personal- ized key to unlock your door, your seat and the exterior mirrors will move into your own preferred positions.<

Before activating the programmed adjustment feature, ensure that

the footwell behind the driver's seat is empty and unobstructed. If you fail to do so, persons, animals or objects could be injured or damaged if the seat should move backward.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

58

Passenger-side exterior mirror tilt function Automatic curb monitor*

1. Move mirror selector switch 1 to the driver's mirror position

2. When shifting into Reverse, or plac- ing the selector lever in position R, the passenger-side mirror tilts down- ward. This allows the driver to see the area directly adjacent to the vehi- cle during parking curbs, etc.

How far the passenger mirror tilts can be set individually for each

ignition key.<

You can deactivate this automatic fea- ture by setting the mirror selection switch to the passenger side position.

Seat heating*

The seat cushion and backrest can be heated with the ignition key in position 2.

You can select different heating modes by repeatedly pressing the buttons.

You can also switch the higher heating modes off directly:

Press the button and hold it slightly longer.

Seat and mirror memory*

59Steering wheel

To adjust Never attempt to adjust the steer- ing wheel while driving the vehicle

it could respond with unexpected movement, posing a potential accident hazard.<

1. Push the locking lever downward 2. Adjust steering column reach and

height for your selected seating posi- tion

3. Pull the lever back up.

Mirrors

To adjust exterior mirrors 1 Switch for 4-way adjustment

2 Selection switch for changing between mirrors

To adjust manually The mirrors can also be adjusted manu- ally:

Press the edge of the lens.

For storing mirror settings, refer to Seat and mirror memory on page 57.

The mirror on the passenger's side is convex. When estimating

the distance between yourself and other traffic, bear in mind that the objects reflected in the mirror are closer than they appear. This means that esti- mates of the distance to following traffic should not be regarded as precise.<

Electric defrosting Both mirrors are automatically heated when you turn the ignition key to posi- tion 2.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

60

Interior rearview mirror To reduce glare from vehicles behind you when you are driving at night, tilt the mirror by turning the button.

Vehicles without alarm system:

Tilt the small lever forward.

Interior rearview mirror with automatic dimming feature* This mirror automatically responds to ambient light and headlamp glare from following vehicles by dimming through an infinitely variable range and auto- matically reverts to its clear, undimmed setting whenever you shift into Reverse or move the selector lever into position R.

To ensure that the mirror continues to operate efficiently, ensure that the pho- tocells remain clear and unobstructed. One photocell is integrated in the mir- ror's lens see arrow while the other is located at an offset position on the

rear of the mirror. Refrain from attach- ing stickers or other objects to the windshield in the area immediately behind the rearview mirror.

Mirrors

61

Passenger safety systems

Airbags

1 Front airbags on the driver and pas- senger sides

2 Side airbags on the driver and pas- senger sides front and rear*

Protective effect The front airbags supplement the three- point safety belts by providing addi- tional protection in the event of a severe frontal collision in which the pro- tection afforded by the belts alone may no longer be sufficient. The side airbags provide protection in the event of a col- lision from the side. They help support the respective seat occupant's upper body.

For information on the correct sitting posture, refer to page 52.

The side airbags in the rear pas- senger area* of your vehicle may

already have been deactivated by a BMW center. You may have them acti- vated if you desire to do so. Please contact your BMW center for additional information.<

The airbags do not deploy in response to minor collisions, rear

impacts and certain kinds of vehicle rollover.<

Do not apply adhesive materials to the cover panels of the airbags,

cover them or modify them in any other way. Do not remove the airbag restraint system. In the event of a malfunction, deactivation or triggered activation as a response to an accident of the air- bag restraint system, consult your BMW center for inspection, repair or disas- sembly. Do not modify or tamper with either the wiring or the individual com- ponents in the airbag system. These include the upholstered covers on the steering wheel, instrument panel, side trim panels of the doors and front roof pillars and on the sides of the headliner. Also, do not attempt to remove the steering wheel. Unprofessional attempts to service the system could lead to failure in an emergency or undesired airbag activation, either of which could result in personal injury. Do not touch the individual components immediately after the system has been activated, as this could result in per- sonal injury.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

62

At all times, occupants should sit upright and be properly restrained

infants and small children in appropri- ate child-restraint systems; larger chil- dren and adults using the safety belts. Never let an occupant's head rest near or on a side airbag because the inflating airbag could cause a serious or fatal injury. Please note that the word Airbag imprinted on the door trim panel indi- cates the airbag's location. Accident research shows that the saf- est place for children in an automobile is in the rear seat. However, a child sit- ting in the rear seat and not properly restrained could place his or her head on or near the airbag, if so equipped. For example, a child even though belted in may fall asleep with his or her head against the side airbag. It may be difficult for a driver to ensure that children in the rear seat will remain properly positioned at all times and not place their heads on or near the side airbag. Therefore, we recommend that the rear-seat side airbags, if installed in the vehicle, be deactivated if children will travel in the rear seat. The rear seat side airbags may already have been deactivated by a BMW cen- ter. If you are uncertain of their status, or wish to have the airbags activated or

deactivated, please contact your BMW center.<

Even when all these guidelines are fol- lowed, there is still a small residual risk of injuries to the face, hands and arms occurring from airbag deployment in isolated instances.

In sensitive individuals, the ignition and inflation noise may induce a mild hear- ing loss that is temporary in most cases.

Corresponding airbag warning labels are located on both sun visors.

This is the right way a child should sit in a child restraint when rear side airbags are provided.

Airbags

63

This is the right way a larger child should sit wearing the seat belt when rear side airbags are provided.

Indicator lamp The indicator lamp indicates the operational status of the airbag system when the ignition key is

in position 1 or higher.

System operational:

>The indicator lamp comes on briefly when you turn the ignition key to position 1 or higher.

System malfunction:

> Indicator lamp does not come on or > indicator lamp lights up continuously.

If there is a system malfunction, there is a risk that the airbags will

not be triggered within their normal response range, even if the level of impact would normally have triggered them. Have your BMW center inspect the airbag system immediately.<

Airbags

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

64 Transporting children safely

To avoid undesired movement at high speeds, always store the rear

safety belts in their retainers when they are not in use.<

Commercially available child-restraint systems are designed to be secured with a lap belt or with the lap belt por- tion of a combination lap/shoulder belt. Improperly or inadequately installed restraint systems can increase the risk of injury to children. Always read and follow the instructions that come with the system.

Correct location for installing In your BMW, all seats equipped with a three-point safety belt except for the driver's seat are suitable for installing universal child-restraint systems of all age classes and which have been approved for the age group in question.

Child-restraint system with tether strap If you use a child-restraint system with a tether strap, two additional tether anchorage points have been provided.

Depending on the location selected for seating in the rear passenger area, attach the tether strap to the corre- sponding anchorage point to secure the child-restraint system, as shown in the illustration.

1. Open the convertible top compart- ment lid, refer to page 41 or 46

2. Lift the headrest and pass the tether strap between the headrest and the seat back. It is recommended that you return the head restraint back to its lowest possible position

3. Adjust the tether strap according to the child-restraint manufacturer's instructions

4. Close the convertible top compart- ment panel.

65

It is recommended to cover the child- restraint attaching clip with a soft mate- rial to prevent damage to the stored soft top.

Should a hard top be installed, the fitting of child harness tether

strap/s if child seat is required is necessary before installation of the hard top.<

Before installing any child- restraint device or child seat,

please read the following: Never install a rearward-facing child- restraint system in the front passenger seat of this vehicle. Your vehicle is equipped with an airbag supplemental restraint system for the front passenger. Because the backrest on any rearward-facing child-restraint system of the kind designed for infants under 1 year and 20 lbs/9 kg would be within the airbag's deploy- ment range, you should never mount such a device in the front passenger seat, since the impact of the airbag against the child restraint's backrest could lead to serious or fatal injuries. If it is necessary for a child not an infant to ride in the front seat, certain precautions should be taken. First, move the passenger seat as far away from the dashboard as possible. This important precaution is intended to maximize the distance between the air- bag and the child. Older children should be tightly secured with the safety belt after they have outgrown a booster seat that is appropriate for their age, height, and weight. Younger chil- dren should be secured in an appropri- ate forward-facing child-restraint sys-

tem that has first been properly installed with a safety belt. Never install a rearward-facing child- restraint system in the front passenger seat. We strongly urge you to carefully read and comply with the instructions for installation and use provided by the child restraint's manufacturer when- ever you use such a device. Do not attempt to modify child-restraint systems. If you do this, the protection provided by these systems could be impaired. Be sure that all occupants of all ages remain properly and securely restrained at all times.<

All rear seating positions in your vehicle meet the recommendations of SAE J1819, an industry-recommended practice for securing child-restraint sys- tems in motor vehicles.

Transporting children safely

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

66

Securing child-restraint system All of the rear belt retractors and the front passenger's safety belt can be locked for mounting and securing child- restraint systems.

A label with the appropriate instructions is located in the immediate vicinity of the buckle of each safety belt.

To lock the safety belt Extract the entire length of the belt from the inertia reel mechanism. Allow the reel to retract the belt somewhat and engage the buckle, then tighten the belt against the child-restraint system. The retraction mechanism is now locked.

The belt cannot be extracted further. Always observe the installation instruc- tions provided by the manufacturer of the child-restraint system.

To unlock the safety belt Release the safety belt, remove the child seat and retract the safety belt to its end position on the belt retractor.

LATCH child-restraint mounting system LATCH: Lower Anchors and Tethers for CHildren

The left and right rear seats are both equipped with a LATCH child-restraint mounting system.

Transporting children safely

67

Canadian models only:

The LATCH anchorage points are iden- tified by buttons.

The anchorage points for the LATCH child-restraint system are located behind the upholstery at the positions indicated by the arrows.

Carefully slide the brackets through the gaps in the upholstery at the indicated locations.

Always follow all manufacturer's instructions and observe all safety

precautions when installing the LATCH child-restraint mounting system. To avoid undesired movement at high speeds, always store the rear safety belts in their retainers when they are not in use.<

Your BMW center can provide you with a special installation aid* that helps pre- vent damage to the upholstery.

Press the installation aid firmly in the crack between the seat and the back- rest upholstery until both funnels click onto the LATCH system bars in the seat.

The illustration is an example showing the anchorages for a LATCH child seat system on the right rear seat.

Transporting children safely

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

68 Rollover protection system

In the event of an accident or some other critical driving situation extreme tilting in the longitudinal or transverse axis, loss of contact with the ground the rollover protection system will be automatically activated. The protective bars located in the rear head restraints extend within fractions of a second.

In addition to the integrated rollover bar in the windshield frame, the rollover protection system affords all the vehicle occupants necessary headroom.

Always keep the travel path for the rollover protection system free

and clear. Under no circumstances should you cover the head restraints. In the event of less serious accidents, the safety belt will protect you and, depending on the severity of the acci- dent, so will the safety belt tensioner and the multi-stage airbag restraint sys- tem as well.<

If, after being automatically triggered, its protective function is not needed, then the rollover protection system can be lowered back into place. No special tool is needed for this.

1. Using a screwdriver from the onboard tool kit, remove the cover panel; to do this, position the screw- driver under the notch

2. Push the lever toward the front of the vehicle and keep it in this position

69

3. Keep pressing down on the protec- tive bar see arrow 1 from on top until you hear it click into place

4. Put the cover panel back in place and press down firmly

5. Push the back panel of the head restraint closed see arrow 2.

Do the same for the second protective bar. If you are not familiar with any of the procedures, consult your BMW center.

Have the rollover protection system checked out by your BMW center after it has been inadvertently triggered.

Do not move the convertible top under any circumstances if the

rollover protection system has extended. Do not use the rear head restraints as storage shelves. Absolutely no modifications are to be made to any of the rollover protection system's individual components or any of its wiring. Only your BMW center is to carry out any work on the rollover protection sys- tem. Work done on the system that is carried out improperly could lead to failure in an emergency or accidental activation. Regarding having the system checked to ensure long-term operation: be scru- pulous in adhering to the Service inter- val display for maintenance intervals. Every 2 years at the latest, the rollover protection system must be inspected at a BMW center.<

Rollover protection system

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

70 Vehicle Memory, Key Memory

How the system functions No doubt you have reflected at one time or another on how great it would be if you could permanently configure your vehicle's various features and adjustments to mirror your own individ- ual preferences. In engineering your vehicle, BMW has provided for a num- ber of options for personal adjustment that can be programmed into your vehi- cle at your BMW center.

The available configuration data fall into two categories, according to whether their primary orientation is the vehicle Vehicle Memory or the individual Key Memory. Provided that each per- son has a separate remote-control key, you can have your BMW center enter basic adjustment data for up to four individuals in the system.

The system then relies on a bilateral data exchange to identify the individual user and executes the selected settings whenever the remote control unit is used to disengage the door locks.

Distinguishing between keys Color-coded decals have been pro- vided to help you distinguish individual keys with different settings.

What the system can do Your BMW center can provide you with details on the capabilities of the Vehicle Memory and Key Memory systems.

You will see this symbol through- out the Owner's Manual. It is to

remind you at appropriate places of the settings that are available to you.<

Examples for Vehicle Memory:

>Various signals as acknowledgment when locking or unlocking your vehi- cle, refer to pages 31, 33

>Activates/deactivates the 'Follow me home' function, refer to page 97

>Activates/deactivates daytime driv- ing lamps, refer to page 97

>Sets the units of measure for display- ing time, outside temperature, dis- tance traveled and fuel consumption in the instrument cluster

>When you shift into Reverse, an acoustic signal indicates that PDC has been activated, refer to page 92

>Switches on rear window defroster automatically, refer to pages 104, 109

>Activates/deactivates various alarm system functions, refer to page 39

>After giving an ice warning, the onboard computer display returns to the previous setting, refer to page 90.

Examples for Key Memory:

>Unlocks driver's door first, then the vehicle's remaining locks, refer to page 33

>Locks the vehicle automatically after you start off, refer to page 34

>Automatically adjusts the driver's seat to the personal programmed settings when the vehicle is unlocked, refer to page 57

>Automatic tilting of the passenger- side mirror, refer to Automatic curb monitor, page 58.

71

Driving

Ignition lock

Ignition key positions 0 Steering locked

1 Steering unlocked

2 Ignition on

3 Start engine

Steering locked The key can only be inserted and removed in this position.

After removing the key, turn the steer- ing wheel slightly to the left or right until you hear the lock engage.

If the key is not removed, an acoustic signal sounds when the driver door is opened.

Vehicles with automatic transmis- sion:

Do not move the selector lever from position P until the engine is running, ignition key position 2. Your vehicle is equipped with an inter- lock. Therefore, the ignition key cannot be turned to position 0 or removed until the selector lever is in position P.<

Vehicles with manual transmis- sion:

Step on the clutch when starting the vehicle. A lockout prevents the engine from starting if the clutch is not depressed.<

Steering unlocked You will find that it is often easier to turn the ignition key from position 0 to posi- tion 1 when you move the steering wheel slightly to help disengage the lock.

Individual electrical accessories are ready for operation.

Starting the engine

Do not allow the engine to warm up by leaving it running while the

vehicle remains stationary. Instead, drive off immediately at a moderate engine speed.<

Do not allow the engine to run in enclosed spaces. Otherwise,

breathing the exhaust fumes can lead to unconsciousness and death. The exhaust gases contain carbon monox- ide, an odorless and colorless, but highly toxic gas. Do not leave the vehi- cle unattended with the engine running. An unattended vehicle with a running engine represents a safety hazard. When driving, standing at idle or park- ing the vehicle, take care to avoid con- tact between the hot exhaust system and flammable materials grass, hay, leaves, etc. Such contact could lead to a fire, resulting in serious personal injury and property damage.<

Start the engine. Do not press the accelerator pedal.

Do not actuate the starter for too short a time, but do not actuate it

for more than approx. 20 seconds. Release the ignition key immediately when the engine starts.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

72

If the engine does not start on the first attempt if it is very hot or cold, for instance:

>Press the accelerator pedal halfway down while engaging the starter.

Cold starts at extremely low tempera- tures below approx. +57/156 and at altitudes over 3,300 ft/1,000 m:

>On the first start attempt, it may be necessary to engage the starter for a longer period but no longer than 20 seconds

>Press the accelerator pedal halfway down while engaging the starter.

Extended starting attempts, char- acterized by excessively frequent

or long periods with the starter engaged can damage the catalytic con- verter.<

Engine idle speed is controlled by the engine computer system. Increased speeds at start-up are normal and should decrease as the engine warms up. If engine speed does not decrease, service is required.

To prevent the battery from discharg- ing, always deactivate electrical devices that are not in use. Switch the ignition off when the vehicle is not being driven.

Manual transmission 1. Engage the parking brake 2. Gearshift lever in idling position 3. Start the engine.

Automatic transmission 1. Depress footbrake 2. Place the selector lever in position P

or N 3. Start the engine.

To prevent the vehicle from start- ing off on its own, always move

the selector lever to position P and engage the parking brake before leav- ing your vehicle with the engine run- ning. Do not leave the vehicle unattended with the engine running. An unattended vehicle with a running engine repre- sents a safety hazard.<

Sequential manual gearbox SMG 1. Depress footbrake 2. Move selector lever into position N

3. Start the engine.

If the engine does not start, reen- gage the gear last selected, refer

to the gear indicator in the display, and move the selector lever into neutral position N again. The gearbox is automatically taken out of gear if the driver's door is opened while the engine is running and the driver does not actuate the pedals, the shift paddles or the selector lever. This is accompanied by a warning tone and the flashing gear indicator. The gear display N appears in the instrument cluster.<

Before exiting the vehicle with the engine running, move the selector

lever into position N and apply the park- ing brake. Do not leave the vehicle unattended with the engine running. An unattended vehicle with a running engine repre- sents a safety hazard.<

Starting the engine

73Switching off the engine

You should never remove the igni- tion key when the vehicle is in

motion, as the steering lock could engage. When you leave the vehicle, always remove the ignition key and engage the steering lock. Always engage the parking brake when parking on slopes and inclined sur- faces. Engaging a gear may not provide adequate resistance to rolling.<

Vehicles with manual transmission Turn the ignition key to position 1 or 0.

Automatic transmission Move the selector lever into position P, and turn the ignition key to position 1 or 0.

SMG gearbox If you turn the ignition key to position 1 or 0 with the selector lever in position R, or in sequential mode, a gear auto- matically remains engaged.

If you turn the ignition key to position 1 or 0 with the selector lever in neutral position N, a warning tone and the flashing gear indicator in the display remind you that no gear is engaged to secure the vehicle against rolling.

The warning stops after approx. 9 seconds.

Parking brake

The parking brake is primarily designed to prevent the vehicle from rolling while parked. It operates on the rear wheels.

To engage The detent engages automatically and the indicator lamp in the instrument cluster comes on when the ignition key is in position 2, refer to page 18.

To release Pull up slightly on the lever, press the button and lower the lever.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

74

If exceptional circumstances make it necessary to engage the

parking brake while the vehicle is in motion, do not pull it with excessive pressure. Keep your thumb pressed against the release button while care- fully pulling the lever up. Excessive pressure can lead to over- braking and loss of traction fishtailing at the rear axle. The brake lamps do not come on when the parking brake is engaged. Vehicles with manual or SMG gearbox: Engage the parking brake when parking on downhill roads, since engaging a gear may not provide adequate resis- tance to rolling, not even in first or reverse gear. Vehicles with automatic transmission: place the selector lever in P.<

To avoid corrosion and one-sided braking, apply the parking brake

from time to time when coasting to a standstill at a traffic signal, for exam- ple provided that it is safe to do so.<

Manual transmission

Do not hold the vehicle in place on slopes by slipping or 'riding' the

clutch. Use the parking brake instead. Riding the clutch leads to severe and premature clutch wear.<

6-speed transmission* When changing gear in the 5th/6th gear plane, be sure to press the gearshift lever to the right to prevent inadvert- ently shifting to a gear of the 3rd/4th gear plane.

Reverse Select only when the vehicle is station- ary. Press the gearshift lever to the left to overcome the slight resistance.

When you select reverse the backup lamps will light up automatically when the ignition key is in position 2.

Parking brake

75Sequential manual gearbox SMG*

The concept The sequential manual gearbox SMG is an automated manual gearbox with which clutching and shifting is assumed by an electro-hydraulic system.

The SMG is operated via the selector lever in the center console and two shift paddles on the steering wheel.

It offers the following functions:

>Sequential mode: manual mode >Drive mode: automatic operation >Ability to choose between two differ-

ent driving programs: Standard, Sport

>Operating safety through protection against misshifting

>Automatic upshifts and downshifts in the drive mode

>Automatic downshifts at minimum engine rpm

>Kickdown function in the drive mode. >Acceleration assistant, refer to

page 78.

Selector lever positions The current selector lever position is indicated by a light-emitting diode in the center console.

R: Reverse

N: Neutral

Position for forward driving with one- touch functions:

Sequential mode

+: manual upshifts

: manual downshifts

D: drive mode.

The SMG is ready for operation in igni- tion key position 2.

The gearbox is automatically placed in neutral gear if the

driver's door is opened while the engine is running and the driver does not actu- ate the pedals, the shift paddles or the selector lever. This is accompanied by an acoustic signal and the flashing gear indicator. The gear display N appears in the instrument cluster. A driving position can only be engaged when the driver's door is closed. When the vehicle is unlocked, a buzzer in the area of the transmission indicates that the system is ready for operation.<

Shiftlock When the car is at a standstill, a safety function requires you to depress the brake pedal if you want to move the selector lever from the neutral position N to a driving position.

Driving precautions Use enough acceleration to pull away speedily when moving off on

an uphill gradient. Never try to prevent the car from rolling back on an uphill gradient by depressing the accelerator pedal; always apply the handbrake. Otherwise you could overheat the SMG gearbox.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

76

R Reverse Select only when the vehicle is station- ary.

N Neutral Always engage before starting the engine, refer to Starting the engine on page 72.

Sequential mode Each time the engine is started, the sequential mode is activated as soon as you move the selector lever into the for- ward driving position while the brake is depressed.

The gears are shifted via the shift pad- dles or the selector lever.

It is also possible to drive off in second gear, e.g. on snow-covered roads.

D Drive mode In the drive mode all forward gears are shifted automatically.

To switch from sequential to drive mode: tap the selector lever to the right toward D.

For rapid acceleration, e.g. during passing, depress the accelerator pedal completely: kickdown.

To switch back to sequential mode: tap the selector lever again to the right toward D or change the current gear via the shift paddles or the selector lever.

Kickdown You can achieve maximum acceleration using kickdown.

Depress the accelerator pedal past the increased resistance point at the full- throttle position.

Shifting gears With the selector lever:

>To upshift, tap the selector lever toward +

>To downshift, tap the lever toward .

With the shift paddles on the steering wheel:

>To upshift, pull one of the shift pad- dles

>To downshift, push the paddle.

You accelerate from higher gears, e.g. during passing, by manually downshift- ing.

In the following situations, the SMG in the sequential mode assists you:

>Upshifts and downshifts are only exe- cuted at appopriate combinations of engine rpm and vehicle speed. For

Sequential manual gearbox SMG*

77

instance, downshifts that would result in excessive engine speed can- not be executed.

>When you brake the car to a stop, the transmission automatically shifts down to first gear

>As speed diminishes the transmission will shift down automatically, without any action on your part, just before the vehicle slows to below each gear's minimum speed.

Available displays R N 1 2 3 4 5 6

D1 D2 D3 D4 D5 D6

The currently engaged gear, the selected mode, and any malfunctions are displayed in the instrument cluster.

Indicator lamp If the indicator lamp comes on, there is a malfunction in the transmission system.

All selector lever positions can still be engaged, but in the forward driving positions only certain gears are actually available when the vehicle is driven.

Avoid extreme loads and proceed to the nearest BMW center.

For information on jump-starting and towing the vehicle, refer to page 159.

Warning tone An acoustic signal sounds if the SMG gearbox overheats; if possible you should either stop or increase your pull- away speed so that the system can cool down.

Sequential manual gearbox SMG*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

78

Sport program You can choose between two driving programs: smoothly dynamic or Sport. With the sport program, gearshifts are faster in sequential mode and the shift points are adapted in drive mode.

To activate the Sport program: press the SPORT button. The LED in the but- ton lights up.

Acceleration assistant The acceleration assistant permits opti- mum racing-style acceleration on roads with good grip.

Do not use the acceleration assis- tant frequently as this could other-

wise cause premature wear of the com- ponents.<

1. Activate the Sport program 2. Press and hold the DSC button, refer

to page 93, for more than three sec- onds

3. Quickly press the accelerator pedal down fully: kickdown. The optimum rpm for driving off will be adjusted.

To maintain vehicle stability, always drive with the DSC acti-

vated whenever possible.<

Sequential manual gearbox SMG*

79Automatic transmission with Steptronic*

You can drive as with a normal auto- matic transmission. In addition, you can also shift manually.

When you move the selector lever from the D position to the left into the M/S range, the performance-oriented shift programs of the automatic transmission are engaged. Steptronic enters the manual selection mode and executes the desired shift whenever you tap the selector lever in the direction indicated by + or . Whenever you want to use automatic again, just move the selector lever toward the right to position D.

Under normal operating conditions, fuel consumption is lowest when driving in position D.

Selector lever positions P R N D M/S +

Starting the engine The engine can only be started in selec- tor lever positions P for Park or N for Neutral.

Range selection A catch prevents inadvertent movement of the selector lever to positions R and P. To deactivate the catch, press the button on the front of the selector lever knob, see arrow.

While the vehicle is stationary and before shifting out of Park or Neu-

tral, depress the footbrake in order to disengage the selector lever's lock mechanism Shiftlock.<

Hold the footbrake down until starting off. Otherwise the vehicle

will 'creep' when a drive position is engaged. To prevent the vehicle from starting off on its own, always move the selector lever to position P and engage the parking brake before leaving your vehicle with the engine running. Do not leave the vehicle unattended with the engine running. An unattended vehicle with a running engine repre- sents a safety hazard.<

P Park Select only when the vehicle is station- ary. Transmission locks to prevent rear wheels from turning.

R Reverse Select only when the vehicle is station- ary.

N Neutral Select only when stopping for an extended period.

D Drive automatic shift program This position is designed for driving under all normal operating conditions. All forward gears are available.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

80

Kickdown In the kickdown mode, you achieve maximum acceleration and top speed in position D.

Depress the accelerator pedal past the increased resistance point at the full- throttle position.

M/S manual operation and Sport program Move the selector lever from D to M/S to activate the Sport program; SD appears in the display panel. The M/S mode is recommended for perfor- mance-oriented driving.

Once in the M/S mode, you can tap the selector lever to switch the automatic transmission from the Sport program to its manual selection mode.

This mode allows you to execute upshifts manually by tapping the lever toward +, while downshifts are selected by tapping in the direction. The dis- plays M1 through M5 appear in the dis- play panel to indicate your current gear selection.

The transmission will only execute upshifts and downshifts that will result in an appropriate combination of vehi- cle speed and engine rpm. For instance, downshifts that would result in excessive engine speed are not exe- cuted. The desired, then the actual gear, briefly appear in the instrument cluster.

To accelerate quickly in the man- ual mode for maneuvers such as

passing another vehicle, shift down manually or employ the kickdown mode.<

Shifting from M/S to the selector lever positions P, R and N is possible only by going through D.

Automatic transmission with Steptronic*

81

Available displays P R N D SD M1 M2 M3 M4 M5

Electronic transmission control module

If the indicator lamp comes on, there is a malfunction in the transmission system.

Bring the vehicle to a stop. Move the transmission selector lever to P. Set the parking brake and turn the engine off ignition key to position 0.

Wait a few seconds, then start the engine.

If the indicator lamp goes out after a few seconds, normal transmission per- formance has been restored. You may continue to drive as usual.

If the indicator lamp does not go out, you can place the selector lever in all positions. However, the vehicle will now only operate in 3rd and 4th gear.

If this happens, avoid extreme engine loads and consult the nearest autho- rized BMW center.

Never work in the engine com- partment when a drive gear for-

ward or reverse is engaged. If you do this, the vehicle could move.<

For towing or jump-starting, refer to the information beginning on page 159.

Automatic transmission with Steptronic*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

82 Turn signal indicator/Headlamp flasher

1 High beams blue indicator lamp

2 Headlamp flasher blue indicator lamp

3 Turn signal indicator green indicator lamps accompanied by a periodic clicking sound from the relay

To signal briefly Press the lever up to but not beyond the detent. It then returns to the center position when released.

If the flashing of the turn signal indicators and the clicking from

the relay are both faster than normal, one of the turn signal indicators has failed.<

83Washer/wiper system/Rain sensor*

0 Wipers retracted

1 Intermittent mode or rain sensor

2 Normal wipe

3 Fast wipe

4 Brief wipe

5 Rotary dial for control of the wipe interval or the sensitivity of the rain sensor

Intermittent mode Not on vehicles with rain sensor.

You can select any of four sweep inter- vals with rotary dial 5.

In addition, the wipe interval varies automatically depending on road speed.

Rain sensor* The rain sensor is located on the wind- shield directly behind the rearview mir- ror.

To activate the rain sensor:

>With the ignition key in position 1 or higher, move the lever to position 1. The wipers will make at least one sweep across the windshield. You can leave the lever in position 1 at all times. With the ignition key in position 1 or higher, all you then need to do to activate the rain sensor is

>briefly turn the rotary dial 5, or >clean windshield 1, refer to page 84.

To adjust the sensitivity of the rain sen- sor: turn rotary dial 5.

To switch off the rain sensor:

Return lever to position 0.

Turn the rain sensor off in auto- matic car washes. Failure to do so

could result in damage caused by undesired wiper activation.<

Normal wiper speed When the vehicle is stationary, the wip- ers switch automatically to intermittent wipe not on vehicles with rain sensor.

Fast wiper speed When the vehicle is stationary, the wip- ers operate at normal speed not on vehicles with rain sensor.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

84

0 Wipers retracted

1 Clean windshield and headlamps

Cleaning windshield and headlamps*

Do not use the washers if there is any danger that the fluid will

freeze on the windshield, as your vision could be obscured. Always use a wind- shield washer antifreeze in cold weather. Refer to page 138. Do not use the washers when the reser- voir is empty. This could cause damage to the washer pump.<

The system sprays washer fluid against the windshield and activates the wipers for a brief period.

When the vehicle's lighting system is switched on, the headlamps will also be cleaned at reasonable intervals.

Windshield washer nozzles The windshield washer nozzles are heated automatically* when the ignition key is in position 2.

Cruise control*

You can store and automatically main- tain any desired vehicle speed above approx. 20 mph / 30 km/h.

The cruise control is available whenever the engine is running and the system has been activated.

To activate the system

In ignition key position 2:

Press the button in the steering wheel. The indicator lamp in the instrument cluster comes on, refer to page 20. You can now use the cruise control.

Do not use cruise control on twist- ing roads, when high traffic den-

sity prevents driving at a constant speed, or when the road surface is slick snow, rain, ice or loose rocks or gravel, sand.<

To deactivate the system

Press the button as often as needed until the indicator lamp in the instru- ment cluster goes out.

Cruise control is also deactivated when the ignition key is in position 0.

Washer/wiper system/Rain sensor*

85

The speed stored in memory is deleted.

To store and maintain speed or to accelerate

Press button + briefly:

The system maintains and stores the current vehicle speed. Every time you tap the button, the speed increases by approx. 0.6 mph / 1 km/h.

Press and hold button +:

The vehicle accelerates without pres- sure on the accelerator pedal. When you release the button, the system maintains and stores the current speed.

If on a downhill gradient the engine braking effect is not suffi-

cient, the controlled speed can be exceeded. Speed can drop on uphill grades if the engine output is insuffi- cient.<

To decelerate

Press button briefly:

If you are already driving with activated cruise control, the speed is decreased by approx. 0.6 mph / 1 km/h every time you tap the button.

Press and hold button :

With the cruise control active, the sys- tem automatically reduces the throttle opening to slow the vehicle. When you release the button, the system main- tains and stores the current speed.

To interrupt the cruise control

When the system is activated, press the button. The indicator lamp stays on. You can use the cruise control again whenever you want by calling up the speed that was stored last.

In addition, cruise control is interrupted automatically:

>When the brakes are applied >When you apply pressure to the

clutch pedal, or when you move the automatic transmission selector lever from D to N

> If you exceed or fall below the pro- grammed speed for an extended period by depressing the accelera- tor, for example.

To recall the stored setting

Press the button:

The vehicle accelerates to and main- tains the last speed stored.

Cruise control*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

86

Everything under control

Odometer

1 Odometer

2 Trip odometer

Odometer You can activate the displays shown in the illustration with the ignition key in position 0 by pressing the left button in the instrument cluster.

Trip odometer To reset the trip odometer to zero, press the left button with the ignition key in position 1 or higher.

Tachometer

Do not operate the engine with the nee- dle in the red overspeed zone of the gauge.

To protect the engine, the fuel supply is interrupted when you approach this sector.

Energy control

Indicates the current fuel consumption in mpg in liters/100 km on Canadian models. This allows you to see whether your current driving style is conducive to fuel economy with minimum exhaust emissions.

When the vehicle is stationary, the dis- play goes to Maximum zero on Cana- dian models.

87Fuel gauge

Once the indicator lamp stays on con- tinuously, there are still approx. 2.1 gal- lons/8 liters of fuel in the fuel tank.

Fuel tank capacity approx. 16.6 gallons/63 liters.

Certain operating conditions, such as those encountered in mountainous areas, may cause the needle to fluctu- ate slightly.

Fill the fuel tank before it is com- pletely empty. Driving to the last

drop of fuel can prevent the engine from operating properly and result in damage.<

When you switch on the ignition, the indicator lamp lights up briefly as an operation check.

Engine coolant temperature gauge

Blue The engine is still cold. Drive at moder- ate engine and vehicle speeds.

Between the blue and red zones Normal operating range. The needle may rise as far as the edge of the red sector during normal operation.

Red When you switch on the ignition, the warning lamp comes on briefly as an operation check.

If the lamp comes on during normal vehicle operation: the engine has over- heated. Shut off the engine immediately and allow it to cool down.

To check coolant level, refer to page 140.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

88 Service interval display

Remaining distance to next service The displays shown in the illustration appear for a few seconds when the ignition key is in position 1 or higher or after the engine is started.

The next service due appears with the message OIL SERVICE or INSPECTION, together with the dis- tance remaining in miles in kilometers in Canada before the next scheduled service.

The computer bases its calculations of the remaining distance on the preced- ing driving style.

A flashing message and a "" in front of the number mean that the service inter- val has already been exceeded by the distance shown on the display. Please contact your BMW center for an appointment.

Check Control

Display When the ignition key is in position 2, the following information and/or condi- tions are indicated using symbols until the conditions have been corrected.

1 Check the low and high beams as well as the parking lamps

2 Door open

3 Luggage compartment lid open

4 Check tail or brake lamps

When you open the driver's door after having turned the ignition key to posi- tion 0, you will hear an acoustic signal for a few seconds to remind you that the lamps have not been switched off.

89Clock

If you wish to have a permanent time display, you can make this setting in the radio display, refer to the Owner's Man- ual for Radio.

You can set the clock and the time dis- play in the car radio as follows.

Setting Before the clock can be set, the time must be showing in the

instrument cluster display.<

With the ignition key in position 1 or higher

To set ahead: turn the right button to the right.

To set back: turn the right button to the left.

The adjustment speed will increase the longer you continue to hold the right button.

To change the display mode: press the right button briefly.

Every time you press the button, the clock display alternates between the 12-hour and 24-hour mode.

In ignition key position 0: the time is displayed for a few seconds after you press the left button, refer to Odometer on page 86.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

90 Computer

Mode selection With the ignition key in position 1 or higher, you can call up information from the computer using the button in the turn signal lever. The information is dis- played in the instrument cluster. Each time you press the button briefly toward the steering column, a new function is called up in the display.

The displays appear in the following order:

Time of day, outside temperature, aver- age fuel consumption, cruising range, average vehicle speed.

When the ignition key is turned to posi- tion 1 or higher, the last active setting is displayed.

Outside temperature You can change the units of measure, 6/7, for the outside temperature dis- play by pressing the right-hand reset button in the instrument cluster while the temperature display is active. The units of measure, 6/7, in the temper- ature display of the automatic climate control change automatically, refer to page 106.

Ice warning If the outside temperature drops to about 37.57/+36, then the computer will automatically switch to a display of the outside temperature. In addition, a signal sounds as a warning and the dis- play flashes for a brief period.

After giving an ice warning, the display returns to the previous

setting.<

The ice warning does not alter the fact that surface ice can form at

temperatures above 37.57/+36, on bridges or shaded road surfaces, for instance.<

91

Average fuel consumption If you continue to press and hold the button on the turn signal lever, the aver- age fuel consumption being displayed is recalculated from that point in time.

If you wish, you can have the aver- age fuel consumption displayed in

a different unit of measure.<

Range The computer bases its calculations for the cruising range on the operating conditions in the preceding period and on the remaining fuel in the tank.

It is important that you refuel when the cruising range falls below

approx. 35 miles / 50 kilometers. Other- wise, the engine cannot be guaranteed to operate properly and damage may result.<

Average speed If you continue to press and hold the button on the turn signal lever, the aver- age speed being displayed is recalcu- lated from that point in time.

Any time spent when the vehicle is sta- tionary and the engine is switched off is ignored for the calculation.

Computer

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

92

Technology for safety and driving convenience

Park Distance Control (PDC)*

The concept PDC assists you when you back into a parking space. Acoustic signals alert you to the momentary distance to an object behind your vehicle. The system features four ultrasonic sensors mounted in your rear bumper. The mon- itoring range for the two corner sensors extends outward roughly 2 ft/60 cm, while two centrally located sensors detect objects at distances of up to approx. 5 ft/1.50 m.

PDC is a parking aid that can identify objects if they are

approached slowly, as is generally the case when parking. Avoid driving towards objects rapidly; due to underly- ing physical principles, the system may otherwise alert you too late for you to take evasive steps.<

The system starts to operate automati- cally approx. one second after you shift into Reverse or move the selector lever into the R position with the ignition key in position 2.

Let this short period elapse before driving backwards.<

PDC is deactivated when you shift back out of Reverse.

You can have a signal set to con- firm that the PDC has been acti-

vated. The signal then sounds when you shift into Reverse or move the selector lever into the R position.<

Acoustic signals The distance to the nearest object is indicated by a tone sounding at various intervals. As the distance between vehi- cle and object decreases, the intervals between the tones become shorter. A continuous tone indicates the pres- ence of an object less than 1 ft/30 cm away.

The warning signal is canceled after approx. three seconds if the distance to the object remains constant during this time if you are moving parallel to a wall, for instance.

System malfunctions will be indicated by a continuous high-pitched tone when the system is activated the first time. Please have the problem fixed by your BMW center.

PDC does not replace the driver's personal responsibility for evaluat-

ing the distance between the vehicle and any objects. Always remember that the sensors can neither detect nor pro- vide warnings of obstacles located within their blind angles. This applies especially in those cases where the system approaches the physical limits of ultrasonic measurement, as occurs with tow bars and trailer couplings, and in the vicinity of thin or wedge-shaped objects. Moreover, low objects that have already been detected such as a curb edge can disappear out of the detection range of the sensors before a continuous tone sounds. Loud sources of sound from outside or inside the vehicle could drown out the PDC signal tone.<

Keep the sensors clean and free of ice or snow in order to ensure

that they will continue to operate effec- tively. Do not apply high pressure spray to the sensors for a prolonged period of time. Always maintain a distance of more than 4 in/10 cm.<

93Dynamic Stability Control (DSC)

The concept DSC maintains vehicle stability, even in critical driving situations.

DSC is operational every time you start the engine.

DSC contains the Dynamic Traction Control (DTC) and Cornering Brake Control (CBC) functions.

Indicator lamps The indicator lamp in the instru- ment cluster goes out shortly after you switch on the ignition,

refer to page 19.

>The indicator lamp flashes: DSC is actively controlling drive torque and braking intervention

>The indicator lamp stays lit: DSC has been switched off with the button; DTC and DBC are operational. DTC control intervention is not indicated.

The indicator lamp and the brake warning lamp continu- ously light up in yellow:

The DSC, DTC and DBC have been switched off manually or

there is a system malfunction.

The vehicle will remain completely operational, however, without DSC. In the event of a fault, please consult your BMW center.

Indicator and warning lamps for Canadian models.

Deactivating the DSC/activating the DTC Press the DSC button briefly; the indi- cator lamp comes on and stays on.

DSC is deactivated; DTC is operational.

In the following rare situations, it may prove useful to activate the DTC for a brief period:

>When rocking the vehicle or starting off in deep snow or on loose surfaces

>When driving with snow chains >When driving on snow-covered

grades, in deep snow, or on a snow- covered surface that has been packed down from being driven on.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

94

Under these special circumstances traction is increased by deactivating the control systems that enhance traction under normal conditions.

Deactivating the DSC and the DTC Hold the DSC button down for at least 3 seconds. The indicator lamp and the yellow brake warning lamp light up and remain on continuously.

The systems for enhancing stability and traction are deactivated, and there is no active braking intervention or torque control.

To maintain vehicle stability, always drive with the DSC acti-

vated whenever possible.<

Reactivating the DSC Press the button again; the indicator lamp or the indicator lamps will go out. DTC is deactivated.

The laws of physics cannot be repealed even with DSC. An

appropriate driving style always remains the responsibility of the driver. We therefore urge you to avoid using the additional safety margin of the sys- tem as an excuse for taking risks. Whenever the DTC is activated, the DSC is switched off and performs minor stabilizing intervention. Do not make any modifications to the DSC system. Allow only authorized technicians to perform service proce- dures on the DSC.<

Flat Tire Monitor*

The concept As you drive, the Flat Tire Monitor keeps track of pressure levels in all four tires. The system alerts you whenever the inflation pressure of a tire falls sig- nificantly below the pressure of another tire.

The system actually detects pressure loss by monitoring differences in the relative speeds of the four wheels. It interprets variations outside specified limits as severe pressure loss, and then responds by generating a warning.

Functional requirements In order for the Flat Tire Monitor to learn the correct tire inflation pressure, please do the following:

1. Check the tire inflation pressures in all tires

2. Compare them with the tire inflation pressure table on page 25 and cor- rect them, if necessary

3. Initialize the system.

Dynamic Stability Control (DSC)

95

System limitations The Flat Tire Monitor cannot pro- vide you with advance warning of

sudden and severe tire damage caused by external factors and does not detect the balanced and very gradual pressure loss that takes place in all four tires over an extended period of time.<

On the other hand, the following situa- tions can lead to a delayed detection of pressure loss and even to the system not functioning:

>Driving on snow-covered or slippery roads

>Performance-oriented driving: slip at the drive wheels, high levels of lateral acceleration

>When driving with snow chains, false warnings and undetected pressure losses may occur

>When driving with a space-saver spare tire, the Flat Tire Monitor can- not function.

Initializing the system Each time you correct the pres- sure in a tire, or change a wheel or

tire, reinitialize the system immediately afterwards. This requires a bit of driv- ing.<

1. Before driving off, start the engine but do not start driving

2. Press the button as long as you need to until the yellow indicator lamp in the instrument cluster lights up for a few seconds

3. Drive off.

It takes a few minutes before the Flat Tire Monitor can detect a flat tire and issue a warning.

When driving with snow chains or a space-saver spare tire, do not

initialize the system.<

Flat tire The indicator lamp in the instru- ment cluster lights up red. This visual alert is accompanied by

an acoustic warning signal.

1. Carefully reduce speed and come to a stop. Avoid sudden braking and steering maneuvers

2. Determine which wheel is damaged

If this cannot be determined, con- tact your BMW center.<

3. Replace the damaged wheel, refer to Changing a wheel on page 153.

After replacing the damaged tire, initial- ize the system.

Vehicles with Run Flat tires:

1. Carefully reduce your speed to under 50 mph / 80 km/h. Avoid sudden braking and steering maneuvers. Do not exceed a speed of 50 mph / 80 km/h

Flat Tire Monitor*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

96

Because the sides of Run Flat tires are reinforced, a drop in infla-

tion pressure usually cannot be detected from the outside, refer to Run Flat tires, page 156.<

2. To continue driving, follow the instructions under Driving with a damaged tire on page 157.

System malfunction The indicator lamp in the instru- ment cluster lights up yellow. The Flat Tire Monitor is malfunc-

tioning or out of order. Please refer the problem to your BMW center.

Brake force display

The brake force display indicates to the driver of the vehicle behind you how hard you are braking your vehicle.

The display has two levels:

>Normal braking: the brake lamps among the rear lamps and the center brake lamp light up

>Hard braking or use of ABS: the tail lamps light up with the same bright- ness as the brake lamps and thereby intensify the visual effect of the brake lamps.

Flat Tire Monitor*

97

Lamps

Parking lamps/Low beams

Parking lamps The front, rear and side vehicle lighting is switched on. You can use the parking lamps to signal

the position of the vehicle when it is parked. For lighting on one side for parking as an additional feature, refer to page 99.

Low beams When the ignition is switched off while the low beams are on, the headlamps go out and only the

parking lamps remain on.

Follow me home lamps When you activate the headlamp flasher after parking the vehicle with the lamps turned off, the low-beam head- lamps will come on for a short time.

You can also have this function deactivated.<

LIGHTS ON warning When you open the driver's door after having turned the ignition key to posi- tion 0, you will hear an acoustic signal for a few seconds to remind you that the lamps have not been switched off.

Daytime driving lamps* If you desire, the light switch can be left in the second position: when the igni- tion is switched off, the external lighting is also switched off.

You can have the activation set- tings for the daytime driving lamps

programmed on your vehicle.<

Automatic headlamp control* When the switch is set to this position the system automati- cally activates and cancels the

low beams in response to changes in

ambient light in tunnels, at dusk, etc. and in the event of rain and snow. If the low-beam headlamps are on, the LED next to the symbol lights up.

The vehicle's external lights remain on constantly when you

switch on the front fog lamps after the headlamps have come on automati- cally.<

Automatic headlamp control can- not serve as a substitute for the

driver's judgement in determining when the vehicle lights should be switched on. For example, the sensors are not able to detect fog. To avoid safety risks, you should respond to these kinds of low-visibility situations by switching the headlamps on manually.<

You can have the sensitivity of your vehicle's automatic head-

lamp control adjusted.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

98 Adaptive headlights*

The concept Adaptive headlights is a variable head- lamp control system for dynamically illuminating the road. Depending on the steering angle and other factors the light from the headlamps follows the course of the road.

Activating Adaptive headlights With the ignition key in position 2, turn the light switch to the automatic headlamp control

position, refer to page 97.

Adaptive headlights is not active while reversing, and only in one

direction while at a standstill.<

System malfunction The LED above the symbol for the auto- matic headlamp control flashes, refer to page 97. Please have the system inspected at your BMW center.

Instrument lighting

Turn the rotary dial with the parking/ low beam lamps on to adjust the illumi- nation intensity.

99High beams/Standing lamps

1 High beams blue indicator lamp

2 Headlamp flasher blue indicator lamp

3 Standing lamps

Standing lamps, left or right As an additional feature, you can illumi- nate your vehicle on either side for parking:

With the ignition key in position 0, engage the lever in the appropriate turn-signal position.

Fog lamps

Front fog lamps The green indicator lamp in the instrument cluster lights up to indicate that the front fog lamps

are on.

If the automatic headlamp control is on, the low beams will come on

automatically whenever you activate the front fog lamps.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

100 Interior lamps

The interior lamps operate automati- cally.

To switch the interior lamps on and off manually Press button 1 briefly:

If you want the interior lamps to remain off all the time, press and hold the but- ton for approx. 3 seconds.

Press the button briefly to revert to nor- mal operation.

Front reading lamps* Switch on and off with the button 2 adjacent to each lamp.

Rear reading lamps* Rear reading lamps are also provided for rear seat passengers when the hardtop is installed, refer to page 127. Switch on and off with the button adja- cent to each lamp.

In order to prevent battery dis- charge, all of the lamps in the

vehicle are automatically switched off approx. 15 minutes after you turn the ignition key to position 0.<

Light-emitting diodes Light-emitting diodes (LEDs) installed behind translucent lenses serve as the light sources for many of the controls and displays in your vehicle. These light-emitting diodes are related to con- ventional lasers, and legislation defines them as light-emitting diodes, Class 1.

Do not remove the protective lens and avoid staring directly at the

unfiltered beam for several hours, as inflammation of the retina could result.<

101

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

102

Controlling the climate for pleasant driving

Air conditioning

103

1 Air onto the windshield and the side windows

2 Air for the upper body area 105

3 Air to the footwell

4 Air supply/Blower 104

5 Temperature 104

6 Air distribution 104

7 Rear window defroster 104

8 Air conditioning 104

9 Outside air/Recirculated-air mode 104

Air conditioning

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

104

Air supply/Blower You can select blower speeds from 1 to 4. The heating and ventilation become more and more effective as the air sup-

ply settings are increased. In position 0, the blower and the heater are switched off. The outside air supply is blocked in position 0.

Temperature In order to increase the tem- perature of the passenger compartment, turn to the right toward the red zone. The tem-

perature of the incoming air is kept con- stant.

Air distribution You can direct air to flow onto the windows , toward your upper body or into the footwell . All intermediate

settings are possible. In the setting , there is a low flow of air onto the win- dows to keep them free of condensa- tion.

Rear window defroster When the rear window defroster is activated, the indicator lamp

comes on. The rear window defroster switches off automatically.

You can have your vehicle pro- grammed in such a way that the

rear window defroster switches on automatically. This occurs within 5 min- utes after starting the engine when out- side temperatures are below approx. 397/+46.<

Air conditioning The air is cooled and dehumidi- fied and depending on the

temperature setting rewarmed.

Depending on the weather, the wind- shield may fog over briefly when the engine is started. Air conditioning helps prevent the windows from fogging up.

Condensation forms during opera- tion of the air conditioning system,

which then exits under the vehicle. It is thus not unusual for a small puddle to form under the car while the system is running.<

Outside air/Recirculated-air mode You can respond to unpleasant external odors by temporarily

blocking the supply of outside air. The system then recirculates the air cur- rently within the vehicle.

If the windows should fog over in the recirculated-air mode, switch

this mode off and increase the air sup- ply as required.<

Air conditioning

105

Draft-free ventilation You can adjust the blower controls for the upper body area to obtain the opti- mum airflow rates and directions for your personal requirements:

1 Rotary dials for infinitely variable opening and closing of the vent out- lets

2 Levers for airflow direction

3 Rotary dial 3 allows you to control the temperature of the airflow from these outlets as desired

Microfilter The built-in microfilter removes dust and pollen from the incoming air. Your BMW center will replace it during rou- tine maintenance. A substantial reduc- tion in airflow indicates that the filter needs to be replaced before scheduled maintenance.

To defrost windows and remove condensation 1. Set the blower speed control for the

airflow rate to position 4 2. Turn the rotary temperature control

completely to the right, toward the red zone

3. Turn to the rotary control for air dis- tribution to position

4. Switch on the rear window defroster to defrost the rear window.

Air conditioning

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

106 Automatic climate control*

107

1 Air onto the windshield and the side windows

2 Air for the upper body area 109

3 Air to the footwell

4 Air inlet for interior temperature sensor please keep clear and unobstructed

5 Outside air/Automatic recirculated- air control (AUC)/Recirculated air 109

6 Automatic air distribution and supply 108

7 Individual air distribution 108

8 Temperature 108

9 Display for temperature 108 and air supply 108

10 Air supply/Blower 108

11 To defrost windows and remove condensation 108

12 Air conditioning 108

13 Rear window defroster 109

Automatic climate control*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

108

Tips for pleasant driving Use the automatic mode switch on with AUTO button 6. Select the desired interior temperature.

Detailed setting options are described for you in the following section.

You can make the settings of your vehicle in such a manner that,

when you unlock the vehicle with the remote control of your personal key, your own personalized setting for the automatic climate control is initiated.<

Automatic air distribution and supply

The AUTO program adjusts the air distribution and the air sup-

ply for you and in addition adapts the temperature to external influences summer, winter to meet preferences you can specify.

Individual air distribution You can cancel the AUTO pro- gram by selecting specific dis- tribution patterns to suit your own individual requirements.

While the AUTO program is then deacti- vated, the automatic airflow control remains in operation. Air flows onto

the windows , toward the upper body , and into the footwell . You can reactivate the automatic air distri- bution mode by selecting the AUTO button.

Temperature The interior temperature that appears in the display panel is a general figure intended for refer-

ence purposes. We recommend 727/ +226 as a comfortable setting, even if the air conditioning is on. When you start the vehicle, the system ensures that the selected temperature is achieved as quickly as possible. It then maintains this temperature, regardless of the season.

To select the units of measure 6/7 of the display, refer to page 90.

Air supply/Blower By pressing the upper or lower button, you can vary the air sup- ply. This deactivates the auto-

matic control of the air supply, AUTO disappears from the display panel. Nev- ertheless, the automatic air distribution remains unchanged. You can reactivate the automatic air distribution mode by selecting the AUTO button.

When the lowest blower speed is set and you press the lower button, all of the displays are canceled: the blower, heating and air conditioning are switched off. The outside air supply is blocked. You can reactivate the system by pressing any button for the auto- matic climate control.

To defrost windows and remove condensation

This program quickly removes ice and condensation from the

windshield and the side windows.

Air conditioning The air is cooled and dehumidi- fied and depending on the

temperature setting rewarmed.

Depending on the weather, the wind- shield may fog over briefly when the engine is started. Air conditioning helps prevent the windows from fogging up.

Condensation forms during opera- tion of the air conditioning system,

which then exits under the vehicle. It is thus not unusual for a small puddle to form under the car while the system is running.<

Automatic climate control*

109

Outside air/Automatic recirculated-air control (AUC)/ Recirculated air

You can respond to unpleasant external odors or pollutants by

temporarily stopping the flow of outside air. The system then recirculates the air currently within the vehicle.

Press the button repeatedly to select one of three different operating modes.

> Indicator lamps off: outside airflow is on

>Left indicator lamp on automatic mode: the system recognizes pollut- ants in the outside air and blocks the flow of air when necessary. The sys- tem then recirculates the air currently within the vehicle. Depending on the air quality, the automatic system then switches back and forth between outside air supply and recirculation of the air within the vehicle

>Right indicator lamp on: the flow of outside air into the vehicle is perma- nently blocked. The system then recirculates the air currently within the vehicle.

If the windows should fog over in the recirculated-air mode, switch

this mode off and increase the air sup- ply as required.<

Rear window defroster With the convertible top closed or with the hardtop* mounted,

press the button. The indicator lamp comes on. The rear window defroster switches off automatically.

You can have your vehicle pro- grammed in such a way that the

rear window defroster switches on automatically. This occurs within 5 min- utes after starting the engine when out- side temperatures are below approx. 397/+46.<

Draft-free ventilation You can adjust the blower controls for the upper body area to obtain the opti- mum airflow rates and directions for your personal requirements:

1 Rotary dials for infinitely variable opening and closing of the vent out- lets

2 Levers for airflow direction

3 Use the rotary dial to control the tem- perature of the airflow: >Rotate toward blue colder >Turn toward red warmer

Automatic climate control*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

110

Microfilter/activated-charcoal filter The built-in microfilter removes dust and pollen from the incoming air. The activated-charcoal filter provides addi- tional protection by filtering gaseous pollutants from the outside air. Your BMW center replaces this combined fil- ter as a standard part of your scheduled maintenance. A substantial reduction in airflow indicates that the filter needs to be replaced before scheduled mainte- nance.

Automatic climate control*

111

Interior conveniences

Glove compartment

To open Pull the handle. The lamp in the glove compartment comes on.

To close Fold the cover back up.

To prevent injury in the event of an accident, close the glove com-

partment immediately after use.<

To lock Lock with one of the master keys. A master key will also be required to unlock the glove compartment.

If for example for valet parking you turn over only your spare key,

refer to page 30, then access to the glove compartment and luggage com- partment is not possible.<

Rechargeable flashlight The flashlight is located on the left- hand side of the glove compartment.

It features integral overload-protection, so it can be left in its holder continu- ously.

To avoid completely discharging and possibly damaging the flash-

light, always ensure that it is switched off before inserting it in the socket.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

112 Integrated universal remote control*

The concept The integrated universal remote control takes the place of up to three different handheld transmitters belonging to var- ious radio remote control devices, such as door openers and home alarm sys- tems. The integrated universal remote control recognizes and learns the signal sent by each original control device.

The signal of an original control device can be programmed into one of the three memory buttons 1. Afterwards, the programmed memory button 1 can be used to operate the corresponding device. The signal transmission is indi- cated by the indicator lamp 2.

Before selling the vehicle, clear the memory buttons 1, refer to page 114.

While programming is in progress and before operating any pro-

grammed system by remote control using the integrated universal remote control, make sure that the area of movement of the system in question is clear of people, animals and inanimate obstructions, in order to avoid possible injury or damage. Also comply with the safety precautions issued for the origi- nal control device.<

Checking compatibility If this symbol is depicted on the packaging or in the operating instructions of the original con-

trol device, it is safe to assume that the remote-controlled system is compatible with the integrated universal remote control.

If you have additional questions, please consult your BMW center

or call 1-800-355-3515. You can also visit these websites: www.bmwusa.com or www.homelink.com. HomeLink is a registered trademark owned by Johnson Controls, Inc.<

1 Memory buttons

2 Indicator lamp

Programming a fixed-code control device Fixed-code control device

1. Turn the ignition key to position 2 2. Initial operation: press and hold

down both outer buttons 1 for approx. 20 seconds until the indica- tor lamp 2 flashes. The three memory buttons 1 are cleared

113

3. Hold the original control device approx. 2 to 8 in / 5 to 20 cm away from memory buttons 1.

The required distance between the control device and the mem-

ory buttons 1 may vary, depending on the system of the original control device in question.<

4. Simultaneously press the command button of the original control device and the desired memory button 1 on the integrated universal remote con- trol. Indicator lamp 2 starts to flash slowly. When indicator lamp 2 flashes rapidly, release both but- tons. If the indicator lamp 2 does not flash rapidly after approx. 15 seconds, select a different dis- tance between the two devices

5. To program other original control devices, repeat steps 3 and 4.

The corresponding memory button 1 is now programmed with the signal of the original control device.

The system can be operated from igni- tion key position 2.

If the system cannot be operated after repeated attempts at pro-

gramming, check whether the original control device is equipped with an alternating-code system. You can either check the operating instructions of the original control device for this informa- tion, or you can press and hold down the programmed memory button 1 of the integrated universal remote control. If indicator lamp 2 of the integrated uni- versal remote control flashes rapidly for a brief period and then remains on for approx. 2 seconds, the original control device is equipped with an alternating- code system. In this case, you have to program the memory buttons 1 as described below for an alternating- code control device.<

Programming an alternating-code control device You will need to follow the operating instructions of the system in question in order to program the integrated univer- sal remote control. Read through the operating instructions for information

on synchronization. Comply with the following additional instructions when you program an alternating-code con- trol device:

You will find programming easier if you have the assistance of

another person.<

1. Park the vehicle within range of the radio remote controlled device

2. Program the integrated universal remote control as described above in the section on fixed-code program- ming

3. Locate the button on the receiver of the target device, for example on the drive

4. Press the button on the receiver of the target device. Once you have completed step 4, you have approx. 30 seconds to complete step 5

5. Press the programmed memory button 1 of the integrated universal remote control three times.

The corresponding memory button 1 is now programmed with the signal of the original control device.

Please contact your BMW center if you have any questions.<

Integrated universal remote control*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

114

Deleting memory buttons Press and hold down both outer buttons 1 of the integrated universal remote control for approx. 20 seconds until the indicator lamp 2 flashes: All threee memory buttons are cleared.

It is not possible to delete individual memory buttons 1.

Storage compartments

Front center armrest To open: press the button and fold up.

Additional compartments and nets* You will find additional storage com- partments in the front doors and in the center console. Storage nets are on the front seat backrests.

Integrated universal remote control*

115

Beverage holders, coin box A coin box and two beverage holders are provided in the center console.

Cellular phone*

Hands-free system On vehicles that are wired for a tele- phone* or equipped with a communica- tions package*, the cover for the hands-free microphone is located in the headliner near the interior lamp.

For further information on using your cellular phone, refer to the separate Owner's Manual.

Ashtray, front*

To empty Press on the edge of the open cover. The ashtray moves up and can be removed.

Cigarette lighter Hold or touch the hot cigarette lighter by the knob only. Holding

or touching it in other areas could result in burns. The cigarette lighter remains opera- tional when the ignition key has been removed. For this reason, children should never be left in the vehicle unat- tended.<

Press the lighter 1 in. You can remove the lighter from its socket for use as soon as it springs back out.

Storage compartments

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

116

Cigarette lighter socket Suitable for attaching power supplies for flashlights, car vacuum cleaners, etc., up to a rating of approx. 200 watts at 12 volts. Avoid damage to the socket caused by inserting plugs of different shapes or sizes.

Ashtray, rear*

To empty Press on the edge of the open cover in the opening direction. The ashtray moves up and can be removed.

Ashtray, front*

117

Loading and transporting

Ski bag*

The ski bag allows the safe and clean transport of up to 4 pairs of standard skis or up to two snowboards.

The length of the ski bag and the addi- tional space provided in the luggage compartment make it possible to carry skis up to 6 ft 10 in / 2.10 m long. Because of the tapered shape of the bag, only two pairs of skis longer than 6 ft 10 in / 2.10 m can be carried.

Loading 1. Take the safety belts out of their

holders 2. Press button downward and remove

the filler piece by pulling it forward 3. Extend the ski bag between the front

seats. The zipper provides conve- nient access to stored items. It may be opened to allow the ski bag to dry

4. Press the button in the luggage com- partment

5. Use the magnetic holder to fasten the cover panel to the back wall.

To store the ski bag, perform the above steps in reverse sequence.

Securing cargo Secure skis and any other objects stored in the bag by tightening the

retaining strap at the buckle.<

Be sure that your skis are clean before loading them into the bag.

Avoid damage from sharp edges during loading.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

118

When reattaching the cover, guide both bars into the guide and press

the cover back into place. Secure the safety belts in their holders again.<

Cargo loading

Avoid overloading the vehicle so that the permitted load on the tires

is not exceeded. Overloading can lead to overheating and internal tire damage. The ultimate result can assume the form of a sudden air loss.<

Determining the maximum load 1. Locate the following statement on

your vehicles placard*:

The combined weight of occu- pants and cargo should never

exceed XXX kg or YYY lbs., as this could otherwise result in damage to the vehicle or unstable driving conditions.<

2. Determine the combined weight of the driver and passengers that will be riding in your vehicle

3. Subtract the combined weight of the driver and passengers from XXX kilograms or YYY pounds

Ski bag*

119

4. The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the XXX amount equals 1,400 lbs. and there will be five 150 lbs. passengers in your vehi- cle, the amount of available cargo and luggage load capacity is 650 lbs.: 1,400 lbs. minus 750 lbs. = 650 lbs.

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4

6. If your vehicle will be towing a trailer, load from your trailer will be trans- fered to your vehicle. Consult the manual for transporting a trailer to determine how this may reduce the available cargo and luggage load capacity of your vehicle.

Stowing cargo >Load heavy cargo as far forward as

possible directly behind the lug- gage compartment partition and as low as possible

>Cover sharp edges and corners.

With the convertible top closed, you can increase the space in the

luggage compartment refer to page 37 by folding back the convert- ible top compartment panel. We recommend that you always fold the convertible top compartment panel down as soon as you have removed your cargo from the luggage compart- ment. This way, you can be sure that you can always operate your convert- ible top at any time. At the same time, when the top is raised you should fold the convertible top compartment panel back up before stowing large objects in the luggage compartment; this precaution will help reduce the likelihood of damage to either the convertible top compartment or your luggage.<

Cargo loading

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

120

Securing cargo >For small, light items, use the rubber-

lined, non-skid side of the floor mat or secure using the luggage compart- ment net* or elastic straps

>For large, heavy pieces, see your BMW center for load-securing devices*. Anchorages located in the luggage compartment can be used for fastening the load-securing devices.

Read and comply with the information enclosed with the load-securing devices.

Always position and secure loads correctly. If you do not, the load

can endanger the passengers during braking or evasive maneuvers. Do not exceed the approved gross vehicle weight or the approved axle loads, refer to page 168, otherwise the vehicle's operating safety is no longer assured and the vehicle will not be in compliance with the certification regu- lations. Do not stow heavy or hard objects in the passenger compartment without securing them. Otherwise they could be thrown around during braking and eva- sive maneuvers and could endanger the passengers.<

Cargo loading

121Roof-mounted luggage rack for the hardtop*

A special roof-rack system is available as an optional extra for your BMW. Please observe the precautions included with the installation instruc- tions.

Anchorages Access to the anchorages:

To fold up the covers, please use the tool provided with the roof-rack system.

Loading and driving notes Roof-mounted luggage racks raise the center of gravity of the vehicle when they are loaded. For this reason, they exercise a major effect on the vehicle's handling and steering response.

You should therefore always remember not to exceed the approved roof load capacity, the approved gross vehicle weight or the maximum axle loads when loading the rack. These weights are listed under Technical data on page 168.

Make sure that the load is not too bulky, and attempt to distribute it evenly. Always load the heaviest pieces first so that they are at the bottom. Make sure that no objects will be in the way when the luggage compartment lid is opening or closing.

Secure the roof-mounted luggage cor- rectly and securely to prevent it from shifting or being lost during driving.

Drive smoothly and avoid sudden acceleration or braking. Do not corner at high speeds.

The roof-mounted luggage rack and the roof load increase the aerodynamic resistance: increased fuel consumption and additional stress on the vehicle's body are the result.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

122

123

Overview

Controls and features

Operation, maintenance

Owner service procedures

Technical data

Index

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

124

Special operating instructions

Break-in procedures

To ensure that your vehicle continues to provide maximum economy throughout an extended service life, we request that you devote careful attention to the following instructions.

Engine and differential The first 1,250 miles/2,000 km:

Constantly vary both vehicle and engine speeds, remembering not to exceed 4,500 rpm or vehicle speeds of over 100 mph / 160 km/h:

Always obey all official speed limits.

Do not use full throttle, and avoid pressing the accelerator beyond the kickdown point during these initial miles.

You can then proceed to increase engine or vehicle speeds once the ini- tial 1,250 miles/2,000 km have elapsed.

Please remember to observe the same break-in procedures if either the engine or the differential should have to be replaced later in the course of the vehi- cle's service life.

Tires Owing to technical factors associated with their manufacture, tires do not achieve their full traction potential until an initial break-in period has elapsed. We thus ask you to drive with extra care during the first 200 miles/300 km.

Always obey all official speed limits.

When the vehicle is operated on wet or slushy roads, a wedge of

water may form between the tire and the road surface. This phenomenon is referred to as hydroplaning, and can lead to partial or complete loss of trac- tion, vehicle control and braking effec- tiveness. Reduce your speed on wet roads.<

Brake system Approx. 300 miles/500 km must elapse before the brake pads and rotors achieve the optimal pad-surface and wear patterns required for trouble-free operation and an extended service life later on.

To break in the separate parking brake drums, apply the parking brake lightly when coasting to a standstill at a traf- fic signal, for instance; use caution to avoid posing a danger to other road users.

You can prevent corrosion in the drums by periodically repeating this proce- dure.

The brake lamps do not come on when the parking brake is set.

Vacuum for the brake system servo unit on your BMW is available only when the engine is running. When you move the vehicle with the engine off when tow- ing, for example substantially higher levels of pedal force will be required to brake the vehicle.<

Clutch Approx. 300 miles/500 km must elapse before the clutch starts to operate at optimum efficiency. Remember to engage the clutch carefully during this initial period.

125General driving notes

Brakes: do not drive with your foot resting on the brake pedal. Even

light but consistent pedal pressure can lead to high temperatures, brake wear and possibly even brake failure. Hydroplaning: when driving on wet or slushy roads, reduce vehicle speed. If you do not, a wedge of water may form between the tires and the road surface. This phenomenon can lead to partial or complete loss of contact between the tires and road surface, as well as loss of vehicle control and braking ability. Driving through water: do not drive through water on the road if it is deeper than 1 ft/30 cm, and then only at walk- ing speed. Otherwise, the vehicle's engine, the electrical systems and the transmission may be damaged. Clothes hooks, with hardtop: when hanging clothing from the hooks, be sure that they will not obstruct the driver's vision. Do not hang heavy objects on the hooks. If you do so, they could cause personal injury during braking or evasive maneuvers.<

Antilock Brake System (ABS)

The concept ABS keeps the wheels from locking during braking, thereby enhancing active driving safety.

Braking with ABS If you are in a situation that requires full braking, you will exploit the full benefits of ABS system if you apply maximum pedal pressure panic stop.

Since the vehicle maintains steering responsiveness, you can avoid possible obstacles with a minimum of steering effort, despite the full brake application.

Pulsation at the brake pedal combined with sounds from the hydraulic circuits indicates to the driver that ABS is in its active mode.

Dynamic Brake Control (DBC) DBC is included in the DSC, refer to page 93. The system responds to sud- den, high-intensity applications of force to the brake pedal by automatically braking the vehicle with maximum boost to achieve the shortest possible braking distances during panic stops. This system also exploits the benefits of ABS. Do not reduce the pressure

exerted against the brake pedal until the braking maneuver has been com- pleted. DBC is deactivated when you release the brake pedal.

Cornering Brake Control (CBC) CBC is an advanced engineering devel- opment of ABS. When braking during cornering with high lateral accelera- tion, or when braking during a lane change, vehicle stability is improved and the steering response is enhanced.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

126 Brake system

Brake fluid level If the brake fluid level is too low and brake pedal travel has become longer, there may be a defect in one of the brake system's hydraulic circuits.

Proceed to the nearest autho- rized BMW center. It may be nec-

essary to apply higher levels of pres- sure to the pedal when stopping and braking distances may also be longer. Please remember to adapt your driving style accordingly.<

Disc brakes Limited vehicle use, extended periods with the vehicle parked or in storage, and operating conditions in which brak- ing is restricted to gentle, low-pressure applications will all increase the ten- dency for corrosion to form on the rotors; this is often accompanied by a simultaneous accumulation of contami- nation on the brake pads. The pads must exert a certain minimal level of pressure against the rotors for the disc brakes' inherent self-cleaning effect to remain effective.

If the brake rotors are corroded, they will tend to respond to braking with a pulsating effect that even extended brake applications will fail to cure.

When driving in heavy rain and on wet roads it is useful to apply light pressure to the brake pedal every few miles. Monitor traffic conditions to ensure that this maneuver does not pose a hazard to you or to other road users. The heat generated in this process helps dry the pads and rotors to ensure that your brake system will respond with undi- minished efficiency when you need it.

When descending steep hills and extended grades, downshift to a gear that will allow you to continue safely with only a minimal amount of braking. By minimizing the loads placed on the brake system, this strategy helps ensure that optimal brake system response will remain available at all times. Use care to avoid exceeding the approved engine-speed range, refer to page 86.

Do not coast with the clutch depressed or with the transmis-

sion or selector lever in Neutral. Do not coast with the engine shut off. The engine provides no braking effect when the clutch is depressed and there is no power-assist for braking or steering when the engine is not running. Never allow floor mats, carpets or any other objects to protrude into the area around the accelerator, clutch and brake pedals and obstruct their move- ment.<

Brake pads For your own safety: use only brake pads that BMW has

released for your particular vehicle model. BMW cannot evaluate non- approved brake pads to determine if they are suitable for use, and therefore cannot ensure the operating safety of the vehicle if they are installed.<

Portable phone in the vehicle BMW recommends using mobile com- munications devices, e.g. portable phones, inside the vehicle with a suit- able outside antenna. Otherwise, it can- not be ruled out that the vehicle elec- tronics and portable phone may interfere with each other.

127Hardtop*

It is not necessary to remove the fabric top even in the winter, when the hard- top is generally in constant use. But you can also remove it easily at any time. Before the fabric top is stored in the convertible top compartment, it must be absolutely dry in order to avoid water spots and mildew from forming.

The hardtop offers reading lamps and clothes hooks that can be used just by pressing. It is also possible to mount a luggage rack on the roof. Please con- sult your BMW center.

When hanging clothing from the hooks, be sure that they will not

obstruct the driver's vision. Do not hang heavy objects on the hooks. If you do so, they could cause personal injury during braking or evasive maneuvers.<

Two people are required for installation or removal. Work with extreme caution in order to avoid paint damage and damage to the body or hardtop.

To facilitate hardtop installation or removal, you can obtain a specially designed hardtop lift* or hardtop rack* at your BMW center.

Storage Storing the hardtop on the floor: slide the styrofoam block that

came with the hardtop onto its center. The arrow on top of the styrofoam block has to be pointing upward when you are doing this.<

Installation 1. Lower the side windows com-

pletely and flip the sun blinds down. If necessary, remove the antenna rod to avoid any damage

2. On vehicles with manual convert- ible top operation, first release the convertible top compartment lid, and, if necessary, open it some- what. On vehicles with fully-auto- matic convertible top operation, open the convertible top compart- ment lid slightly by pressing the button for the operation of the con- vertible top

3. Remove the trim pieces on both sides by pulling them off toward the back and reclose the convert- ible top compartment lid

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

128

4. Open the two locking levers at the front. Press on the buttons to do so. The levers will release slightly. Open the levers as far as possible

5. Before installing, first flip the cover panels that are located underneath the left and right interior lamps down. To do this, press on the slight bump on the cover panel. There is a holder in the cover panel to securely store the trim pieces that have been removed see arrow 1

6. Open the red release levers as far as the stop will allow see arrow 2

7. Position the hardtop onto the sup- ports with the help of a second person. Be sure to put the mount- ings exactly into the proper brack- ets

Lift the hardtop carefully. Be extremely careful not to shift the

seals. Seals that have been shifted out of place or actually pulled out cause leaks.<

8. In the back, close the red locking levers by turning to the inside as far as the stop located behind the trim will allow. Flip the cover panels back into place

9. To lock the hardtop in the front, keep pressing on the front locking levers until you hear them engage

10. Check the rubber weather-strip- ping between the windshield frame and the hardtop on both the left and right sides. If it is folded or bent out of place, you should smooth it back into position by hand to ensure secure and reliable sealing.

Removal Follow the same procedure as when installing, just reverse the steps.

Hardtop*

129

Wheels and tires

Tire inflation pressure

Information for your safety The factory-approved tires are matched to your vehicle and have been selected to provide optimum safety and driving comfort when used properly.

It is not merely the tire's service life, but also driving comfort and above all else driving safety that depend on the con- dition of the tires and the maintenance of the specified tire inflation pressure.

Incorrect tire inflation pressure is a frequent cause of tire damage.

Tire pressure also has a major effect on your BMW's handling response. Be sure to check the tire inflation pressure, including the space-saver spare tire or the spare tire, on a regular basis, at least twice a month and before every extended journey, refer to page 25. If this is not done, incorrect tire pressures can cause driving instability and tire damage, ultimately resulting in acci- dents.<

Tire condition

Tire tread tire damage Inspect your tires frequently for tread wear, signs of damage and for foreign objects lodged in the tread. Check the tread depth.

Tread depth should not be allowed to go below 1/8 in / 3 mm, even though the legally specified minimum tread depth is 1/16 in / 1.6 mm.

Below 1/8 in / 3 mm tread depth, there is a great risk of hydroplaning, even at relatively moderate speeds and with only small amounts of water on the road. Tread wear indicators in the tread-groove base see arrow are distributed around the wheel circumfer- ence and are labeled on the tire side-

wall with TWI Tread Wear Indicator. At a tread depth of 1/16 in / 1.6 mm, the indicators signal that the legally permis- sible wear limit has been reached.

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

130

Do not drive on a deflated flat tire unless your vehicle is

equipped with Run Flat tires. A flat tire greatly impairs steering and braking response, and can lead to complete loss of control over the vehicle. Avoid overloading the vehicle so that the per- mitted load on the tires is not exceeded. Overloading can lead to overheating and internal tire damage. The ultimate result can assume the form of a sudden air loss. Unusual vibrations encountered during normal vehicle operation can indicate a flat tire or some other vehicle malfunc- tion. This type of problem can be caused by contact with curbs, etc. This is also true for irregularities in the vehi- cle's handling characteristics, such as a pronounced tendency to pull to the left or right. Should this occur, respond by immediately reducing your speed. Pro- ceed carefully to the nearest BMW cen- ter or professional tire center, or have the vehicle towed in to have it, its wheels or its tires inspected. Tire damage up to and including sud- den and complete air loss can endan- ger the lives of both the vehicle occu- pants and other road users.<

Tire replacement

To maintain good handling and vehicle response, use only tires of a single tread configuration from a single manu- facturer.

Comply with the specified tire inflation pressures and be sure to have the wheel and tire assembly balanced every time you change a tire or wheel.

DOT quality grades Tread wear

Traction AA A B C

Temperature A B C

All passenger car tires must con- form to Federal Safety Require-

ments in addition to these grades.<

Tread wear The tread wear grade is a comparative rating based on the wear rate of the tire when tested under controlled condi- tions on a specified government test course.

For example, a tire graded 150 would wear one and one-half 1 1/2 times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual condi- tions of their use, however, and may

depart significantly from the norm due to variations in driving habits, service practices and differences in road char- acteristics and climate.

Traction The traction grades, from highest to lowest, are AA, A, B and C.

Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on speci- fied government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

The traction grade assigned to this tire is based on straight-

ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction charac- teristics.<

Temperature The temperature grades are A the highest B and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled condi- tions on a specified indoor laboratory test wheel.

Tire condition

131

Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive tem- perature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

The temperature grade for this tire is established for a tire that is

properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.<

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:

Tread wear 200

Traction AA

Temperature A

BMW advises against using retreaded tires, since driving

safety may be impaired. This is due to the possible variations in casing struc- tures and, in some cases, to their extreme age, which can lead to a decrease in their durability.<

Tire age The date on which the tire was manu- factured is indicated by the code on the sidewall:

DOT... 3603 indicates that the tire was manufactured in week 36 of the year 2003.

BMW recommends the replacement of all tires including the spare tire* when the tires are no more than 6 years old, even if a tire life of 10 years is pos- sible.

Run Flat tires* Before purchasing tires, check if your BMW is equipped with Run Flat tires. These are indicated by a circular sym- bol containing the letters RSC on the tire sidewall, refer to Changing a wheel. In this case, use only Run Flat tires, since no spare wheel is available in the event of a flat.

For more information on Run Flat tires, refer to page 156.

Tire replacement

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

132 Wheel and tire combinations

The right choice BMW recommends using only wheels and tires that have been

approved by BMW for your particular vehicle model, as otherwise body con- tact and serious accidents can result despite the use of the same nominal size, e.g. due to manufacturing toler- ances. BMW cannot evaluate all tires and wheels on the market, and is thus unable to guarantee that the vehicle will continue to perform safely if unap- proved tires and/or wheels are mounted.<

For each tire size, BMW has assessed the safe performance of specific tire brands and approved them for use. Consult any BMW center for details. Comply with any local/national regula- tions, for example by recording the tire type in the vehicle documents.

The correct wheel and tire combi- nation affects various systems

that would otherwise be impaired, for example ABS, DSC and DBC. For this reason, use only tires of the same manufacture and tread configura- tion. In the event of a flat tire, for exam- ple, remount the approved wheel and tire combination as soon as possible.<

Storage Always store tires in a cool, dry place. Store them away from light whenever possible. Protect the tires against con- tact with oil, grease and fuel.

Do not exceed the maximum tire infla- tion pressures specified on the tire sidewall.

Winter tires

Choosing the right tire BMW recommends the use of winter tires for operation under winter road conditions. While all-season tires with M+S designation provide better winter traction than the corresponding sum- mer tires, they generally do not achieve the performance of winter tires.

In the interest of safe tracking and steering response, install winter tires made by the same manufacturer and with the same tread configuration on all four wheels.

Never exceed the maximum speed for which the winter tires

are rated. Unprofessional attempts by laymen to service tires can lead to damage and accidents. Have this work performed by trained professionals only. Any BMW center has the required technical knowledge and the proper equipment and will be happy to assist you.<

Run Flat tires Before purchasing winter tires, check if your BMW is eqipped with Run Flat tires. These are indicated by a circular symbol containing the letters RSC on

133

the tire sidewall, refer to Changing a wheel. In this case, use only Run Flat winter tires, since no spare tire is pro- vided in the event of a flat tire.

Tire condition, tire pressure At tread depths below approx. 3/16 in / 4 mm, winter tires display a perceptible decrease in their ability to cope with winter driving conditions, and should be replaced in the interest of safety.

Comply with the specified tire inflation pressures and be sure to have the wheel and tire assembly balanced every time you change a tire or wheel.

Snow chains* Only certain snow chains have been tested by BMW and determined and approved as roadworthy. Consult any BMW center for details. BMW recom- mends using only these approved fine- link snow chains. Use them in pairs on either summer or winter tires, but only on both rear wheels.

Comply with all manufacturer's safety precautions when mounting the chains. Do not exceed a speed of 30 mph / 50 km/h when using snow chains.

You cannot mount snow chains with the following tires:

225/50 R 16

225/45 R 17

225/40 R 18

245/40 R 17

255/35 R 18

Do not initialize the Flat Tire Moni- tor after mounting snow chains to

the tires. When driving with snow chains, it may be useful to turn off the DSC for a short time, refer to page 94.<

Winter tires

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

134

In the engine compartment

Hood

To release Pull the lever located under the left- hand side of the instrument panel.

Do not attempt to service your vehicle if you do not have the

required technical background. Failure to work in an informed, professional manner when servicing components and materials constitutes a safety haz- ard for vehicle occupants and other road users. If you are not familiar with the guidelines, BMW recommends that you have the operations performed by your BMW center.<

To open Pull the release handle and open the hood.

To close Allow the hood to fall from a height of about 1 ft/30 cm so that it audibly engages.

To avoid injuries, be sure that the travel path of the hood is clear

when it is closed, following the same safety precautions used in all closing procedures. If you notice while driving that the hood is not completely closed, stop immedi- ately and close it securely.<

135

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

136 Engine compartment essentials

137

1 Brake fluid reservoir 141

2 Engine oil dipstick 138

3 Coolant expansion tank 140

4 Reservoir for the headlamp and wind- shield washer system 138

5 Engine oil filler neck 139

6 Auxiliary terminal for jump- starting 159

Engine compartment essentials

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

138 Washer fluid

Headlamp* and windshield washer system Approximate capacity is 5.6 US quarts/5.3 liters.

Fill with water and, if required, with a washer antifreeze additive according to manufacturer's recommendations.

We recommend that you mix the washer fluid before adding it to

the reservoir.<

Antifreeze agents for the washer fluid are highly flammable. For this

reason, keep them away from sources of flame and store them only in closed original containers, inaccessible to chil- dren. Comply with the instructions on the containers.<

Engine oil

Checking the oil level 1. Park the vehicle on a level surface 2. Switch the engine off after it has

reached normal operating tempera- ture

3. After approx. 5 minutes, pull the dip- stick out and wipe it off with a clean lint-free cloth, paper towel, or similar material

4. Carefully push the dipstick all the way into the guide tube and pull it out again

5. The oil level should be between the two marks on the dipstick.

As with fuel economy, oil consumption is directly influenced by your driving style and vehicle operating conditions.

The oil volume between the two marks on the dipstick corresponds to approx. 1.1 US quarts/1 liter. Do not fill beyond the upper mark on the dipstick. Excess oil will damage the engine.

139

Adding engine oil Only add engine oil when the oil level has dropped to just above the lower mark on the dipstick.

BMW engines are designed to operate without oil additives; the

use of additives could lead to damage in some cases. This also applies to the manual transmission, the automatic transmission, the differential, and the power steering system.<

Recommendation: have the oil changed at your BMW center.

Continuous exposure to used oil has caused cancer in laboratory

testing. For this reason, any skin areas that come into contact with oil should be thoroughly washed with soap and water. Store oils, grease and similar materials so that they are inaccessible to chil- dren. Comply with warning labels and information on containers.<

Comply with the applicable envi- ronmental laws regulating the dis-

posal of used oil.<

Specified engine oils The quality of the engine oil is extremely important for the operation and service life of an engine. Based on extensive testing, BMW has approved only certain grades of engine oil.

Use only approved BMW High Perfor- mance Synthetic Oil.

If an approved BMW High Performance Synthetic Oil should be unavailable, you may use small amounts of other syn- thetic oils for topping up between oil changes. Use only oils with the specifi- cation API SH or higher.

Ask your BMW center for details concerning the specific BMW

High Performance Synthetic Oil or syn- thetic oils that have been approved.<

You can also call BMW of North Amer- ica toll-free at 1-800-831-1117 or visit this website: www.bmwusa.com to obtain this information.

Viscosity ratings Viscosity is the oilflow rating as estab- lished in SAE classes.

The selection of the correct SAE class depends on the climatic conditions in the area where you drive your BMW.

Approved oils are in SAE classes 5W-40 and 5W-30.<

These kinds of oil may be used for driv- ing in all ambient temperatures.

Engine oil

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

140 Coolant

Do not add coolant to the cooling system when the engine is hot. If

you attempt to do so, escaping coolant can cause burns. Antifreeze and anti-corrosion agents are hazardous to health. You should always store them in their closed origi- nal containers and in a location which is out of reach of children. Antifreeze and anti-corrosion agents are inflammable. For this reason, do not spill them on hot engine parts. They could ignite and cause serious burns. Comply with the instructions on the containers.<

Comply with the applicable envi- ronmental laws regulating the dis-

posal of antifreeze with corrosion inhib- itor.<

Checking the coolant level and adding coolant Check the coolant level when the engine is cold, approx. 687/+206.

1. Open the cap for the expansion tank by turning it slightly counterclock- wise to allow accumulated pressure to escape, then open

2. The coolant level is correct when the upper end of the red float rod see arrow is at least even with the upper edge of the filler neck, is at least even with the upper edge of the filler neck; see arrow. The end of the float may stick out by a maximum of 3/4 in / 2 cm that is, up to the sec- ond mark on the float

3. If necessary, add coolant. If the cool- ant is low, slowly add coolant until the correct level is reached do not overfill.

141Brake fluid

Indicator lamp The brake warning lamp comes on when the parking brake is not engaged: the brake fluid

level is too low, refer to page 18.

Brake warning lamp for Cana- dian models.

Adding brake fluid For adding brake fluid or for determin- ing and correcting the cause of brake fluid loss, consult your BMW center. Your BMW center is familiar with the specifications for factory-approved brake fluids DOT 4.

Brake fluid loss results in extended pedal travel. Refer to the information on page 126.

Brake fluid is hygroscopic, that is, it absorbs moisture from the air

over time. In order to ensure the brake system's safety and reliability, have the brake fluid changed every two years by a BMW center. Refer also to page 88 and to the Service and Warranty Information Booklet for US models or the Warranty and Service Guide Booklet for Cana- dian models. Brake fluid is toxic and damages the vehicle's paint. You should always store it in its closed original container and in a location which is out of reach of chil- dren. Do not spill the brake fluid and do not fill the brake fluid reservoir beyond the MAX mark. The brake fluid could ignite upon contact with hot engine parts and cause serious burns.<

Comply with the applicable envi- ronmental laws regulating

the disposal of brake fluid.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

142

Maintenance

The BMW Maintenance System

The BMW Maintenance System has been designed as a reliable means of providing maximum driving and operat- ing safety and as cost-effectively for you as possible.

Please keep in mind that regular main- tenance is not only necessary for the safety of your vehicle, but also plays a significant role in maintaining its resale value.

Service interval display While conventional systems rely on milage alone to determine when service is due, the BMW Maintenance System reflects the actual conditions under which the vehicle is operated: some miles are more strenuous than others.

From a maintenance point of view, 62,000 miles/100,000 km accumulated in short-distance urban driving are not the equivalent of the same distance covered at moderate cruising speeds in long-distance highway travel.

The BMW Maintenance System includes the Engine Oil Service and Inspections I and II.

This service strategy accurately reflects your own vehicle's specific needs by defining maintenance intervals accord- ing to individual operating conditions. Minimal use drivers those who drive significantly fewer than 6,200 miles/10,000 km annually should have the engine oil changed at least every 2 years since oil deterio- rates over time, regardless of use.

Service and Warranty Information Booklet for US models/Warranty and Service Guide Booklet for Canadian models For additional information on required maintenance intervals and procedures, please refer to the Service and War- ranty Information Booklet for US mod- els, or the Warranty and Service Guide Booklet for Canadian models.

As a precaution against corrosion, if your vehicle is exposed to potential damage from unimproved road sur- faces we suggest that you have the body checked for damage from stone chips and gravel at the same time.

Have your BMW center perform maintenance and repair.

Be sure that all maintenance work is recorded in the Service and Warranty Information Booklet for US models, or in the Warranty and Service Guide Booklet for Canadian models. These entries confirm that your vehicle has benefitted from regular maintenance, and are also required for warranty claims.<

Care You can find everything you need to know on this topic by consulting the separate Caring for your vehicle bro- chure.

143

Laws and regulations

California Proposition 65 warning

California laws require us to state the following warning:

Engine exhaust and a wide variety of automobile components and

parts, including components found in the interior furnishings in a vehicle, con- tain or emit chemicals known to the State of California to cause cancer and birth defects and reproductive harm. In addition, certain fluids contained in vehicles and certain products of com- ponent wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Battery posts, terminals and related accessories contain lead and lead com- pounds. Wash your hands after hand- ling. Used engine oil contains chemicals that have caused cancer in laboratory ani- mals. Always protect your skin by washing thoroughly with soap and water.<

OBD interface socket

The interface socket for onboard diag- nostics is located on the left-hand side of the driver's side, behind a specially marked cover located beneath the instrument panel. The cover has the let- ters OBD on it.

This interface makes it possible to access data on emissions-related com- ponents using special equipment.

An illuminated indicator informs you of the need for service, not that you need to stop the vehi-

cle. However, the systems should be checked by your BMW center at the next opportunity.

If the indicator blinks or flashes, this indicates a high level of engine misfire. Reduce speed and contact the nearest BMW center immediately. Severe

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

144

engine misfiring for even a short period of time can seriously damage emission control system components, especially the catalytic converter.

SERVICE ENGINE SOON warn- ing lamp for Canadian models.

If the gas cap is not on tight enough, the OBD system can

detect leaking vapor and the indicator will light up. If the gas cap is then tight- ened, the indicator will usually go out after a short period of time.<

OBD interface socket

145

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

146

147

Overview

Controls and features

Operation, maintenance

Owner service procedures

Technical data

Index

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

148

Replacement procedures

Onboard tool kit

The onboard tool kit is located in the luggage compartment lid.

Loosen the wing nut to open.

Windshield wiper blades

1. Switch off the engine 2. Fold the wiper arm completely out

from the windshield 3. Position the wiper blade at an angle

and pull the release spring see arrow

4. Fold the wiper blade down and unhook it toward the windshield

5. Pull the wiper blade past the wiper arm toward the top

6. Insert a new wiper blade and apply pressure until you hear it engage.

149Lamps and bulbs

The lamps and bulbs make essential contributions to the safety of your vehi- cle. Therefore, proceed carefully when handling bulbs. BMW recommends that you have such work performed by your BMW center if you are not familiar with the procedures.

Do not touch the glass portion of a new bulb with your bare hands

since even small amounts of impurities burn in to the surface and reduce the service life of the bulb. Use a clean cloth, paper napkin, or a similar mate- rial, or hold the bulb by its metallic base.<

A replacement bulb set is available from your BMW center.

Before working on the electrical system, switch off the electrical

accessory you are working on or dis- connect the cable from the negative terminal of the battery. Failure to observe this precaution could result in short circuits. To prevent injuries and damage, com- ply with any instructions provided by the bulb manufacturer.<

Low beams H7 bulb, 55 watts

Engine compartment, left side:

The H7 bulb is pressurized. There- fore, wear safety glasses and pro-

tective gloves. Failure to comply with this precaution could lead to injury if the bulb is damaged.<

1. Remove the cover of the headlamp by pressing the tab and lifting the cover off

2. Pull off the plug 3. Release the retaining wire 4. Remove and replace the bulb.

When cleaning the headlamps, please follow the instructions in

the Caring for your vehicle brochure.<

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

150

High beams H7 bulb, 55 watts

Engine compartment, left side:

The H7 bulb is pressurized. There- fore, wear safety glasses and pro-

tective gloves. Failure to comply with this precaution could lead to injury if the bulb is damaged.<

1. Turn the cover to the left and remove 2. Pull off the plug 3. Release the retaining wire 4. Remove and replace the bulb.

Note the letters TOP when putting the cover in place.<

When cleaning the headlamps, please follow the instructions in

the Caring for your vehicle brochure.<

Xenon lamps* The service life of these bulbs is very long and the probability of a failure is very low, provided that they are not switched on and off an unusual number of times. If one of these bulbs should nevertheless fail, it is possible to con- tinue driving with great caution using the fog lamps, provided local traffic laws do not prohibit this.

Because of the extremely high voltages involved, any work on the

xenon lighting system, including bulb- changing, should be carried out by technically qualified personnel only. Otherwise, there is a risk of fatal injury.<

Parking lamps 5 watt bulb

Engine compartment, left side:

1. Turn the bulb holder to the left and remove

2. Pull the bulb off and replace it.

Lamps and bulbs

151

Front turn signal indicators 21 watt bulb 1. Turn the bulb holder with the plug to

the left and remove 2. Pull the bulb off and replace it.

When replacing the bulb on the right, loosen and lift the reservoir

for the headlamp and windshield washer system if necessary.<

Side turn signal indicators 1. Press the front edge of the lamp

toward the back with the tip of your finger and remove

2. Pull off the plug and replace the entire lamp.

The side turn signal indicator is designed using LED technology. If

faulty, the entire side turn signal indica- tor must be replaced.<

Rear lamps 1 Turn signal indicator

2 Backup lamp 21 watt bulb

3 Tail lamp/brake lamp

All bulbs in the fender are designed using LED technology.

Please contact your BMW center in case of a malfunction.<

Lamps and bulbs

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

152

Bulbs in the luggage compartment lid: 1. Using a screwdriver, loosen the clip

2. Swing trim panel down see arrow 1. Unlock bulb holder see arrow 2 and remove

3. Applying light pressure, turn the bulb to the left. Remove and exchange the bulb

4. Press the bulb holder into place con- tinuing until you hear it engage

5. Reinstall the trim panel with the clip.

Center high-mount brake lamp LED strip on the rear window.

Please contact your BMW center in case of a malfunction.

Lamps and bulbs

153

License plate lamps 5 watt bulb

1. Place a screwdriver in the slot and press toward the left to release the lens

2. Replace the bulb.

Changing a wheel

Safety precautions in the event of a flat tire or wheel change:

Stop the vehicle as far as possible from passing traffic. Park on a firm, flat, sur- face. Switch on the hazard warning flashers. Turn the steering wheel to the straight-ahead position and engage the steering lock. Shift into 1st or Reverse, or if you have an automatic transmis- sion position the selector lever in Park, and engage the parking brake. All passengers should be outside the vehicle and well away from your imme- diate working area behind a guardrail, for example. If a warning triangle or portable hazard warning lamp is available, set it up on the roadside at an appropriate distance from the rear of the vehicle. Comply with all safety guidelines and regula- tions. Change the wheel only on a level, firm surface which is not slippery. Avoid jacking the vehicle on a soft or slippery support surface snow, ice, loose gravel, etc. as either the vehicle or the jack could slip sideways. Position the jack on a firm support sur- face. Do not place wooden blocks or similar objects under the jack. They could pre- vent the jack from extending to its full

height and reduce its support capacity. Do not lie under the vehicle or start the engine when the vehicle is supported by the jack. There is otherwise a risk of fatal injury.<

Your BMW is equipped with a space- saver spare tire designed for temporary use in maintaining the vehicle's mobility in an emergency.

To remove the space-saver spare tire, lift the floor panel in the lug-

gage compartment completely out, refer to page 37.<

Lamps and bulbs

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

154

What you will need In order to avoid rattling noises later, note the position of the tools when you remove them and return them to their original position when you are through using them.

>Jack 1 Raise the floor panel in the luggage compartment, refer to page 37, and undo the jack. When you have completed work, fold the handle back and insert it in its holder

>Chock 2 Located behind the jack on the wall in the luggage compartment. Loosen the wingnut to remove it

>Space-saver spare tire next to jack Loosen the wing nut by hand, remove the storage shelf and take the wheel out

>Lug wrench in the onboard tool kit on the underside of the luggage com- partment lid, refer to page 148.

Procedure 1. Read and comply with the safety

precautions provided on the previ- ous page

2. Secure the vehicle to prevent it from rolling: Place the chock against the rear surface of the front tire on the side opposite the side being raised. If the vehicle is parked on a down- ward slope, place the chock securely in front of the tire. If the

wheel must be changed on a sur- face with a more severe slope, take additional precautions to secure the vehicle from rolling

3. Wheels with full wheel covers*: reach into the ventilation openings and pull the cover off

4. Loosen the lug bolts by rotating half a turn

Changing a wheel

155

5. Position the jack at the jacking point closest to the flat tire with the jack base vertically below the jack- ing point. The entire surface of the head of the jack moves into the square recess of the jacking point refer to the detail in the next illus- tration when the jack is cranked

6. Continue raising the vehicle up until the wheel you are changing is raised from the ground

7. Unscrew the lug bolts and remove the wheel

8. Remove accumulations of mud and dirt from the mounting surfaces of the wheel and hub. Clean the lug bolts

9. Position the new wheel or the space-saver spare tire on the hub and screw at least two lug bolts fin- ger-tight into opposite bolt holes

10. Screw in the remaining lug bolts. Screw in all the bolts in a diagonal pattern

11. Lower the jack and remove it from beneath the vehicle

12. Tighten the lug bolts securely in a diagonal pattern

13. Wheels with full wheel covers*: place the wheel cover with the valve opening over the valve. Use both hands to press the cover securely onto the rim

14. Check and correct the tire inflation pressure at the earliest opportunity. Vehicles with Flat Tire Monitor: After mounting the spare tire or correcting the tire inflation pres- sure, reinitialize the system, refer to page 95.

Protect valve stems and valves from dirt using screw-on valve stem caps. Dirty valve stems frequently lead to slow pressure loss.

Do not place the full wheel cover on the space-saver spare tire,

since this could damage the cover.<

Changing a wheel

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

156

The vehicle jack is designed for changing wheels only. Do not

attempt to raise another vehicle model with it or to raise any other type of load. To do so could cause accidents and personal injury. To ensure continued safety, have the tightness of the torque bolts checked with a calibrated lug wrench torque specification: 88.5 lb ft/120 Nm at the earliest opportunity.<

When storing a wheel in the spare tire recess, take care to avoid bending the threaded rod.

If light-alloy wheels other than original BMW light-alloy wheels have been mounted, it may be necessary to use different lug bolts for those wheels.

Replace the defective tire as soon as possible and have the new wheel/tire balanced.

Driving with the space-saver spare tire Drive cautiously. Do not exceed a speed of 45 mph / 80 km/h.

Be aware that vehicle handling may be altered. Anticipate, e.g., reduced track- ing during braking, longer braking dis- tances and changed steering charac-

teristics when approaching limit conditions. These handling characteris- tics will be even more pronounced if winter tires are mounted.

Only one space-saver spare tire may be mounted at one time.

Mount a wheel and tire of the original size at the earliest possible opportu- nity.<

Run Flat tires*

Run Flat tires are labeled on the side- wall with a circular symbol containing the letters RSC. Run Flat tires consist of self-supporting tires and special rims. The tire reinforcement ensures that driving remains possible to a restricted degree in the event of pressure drop or even if the tire is deflated.

When mounting or replacing sum- mer tires with winter tires, or vice

versa, use Run Flat tires since no spare wheel is available in the event of a flat. In this event, BMW recommends con- sulting your BMW center. Your BMW center has the information needed for working with Run Flat tires and is equipped with the necessary special tools.<

Changing a wheel

157

Driving with a damaged tire Depending on the cargo load, Run Flat tires allow you to continue driving at a maximum speed of 50 mph / 80 km/h. If there is a total loss of tire inflation pres- sure, 0 psi/0 kPa, or obvious tire dam- age, you can determine the distance you may continue driving based on the following values:

>With a light load: 1 to 2 persons without luggage: approx. 150 miles/250 km

>With a medium load: 2 persons, luggage compartment full; or 4 persons without luggage: approx. 100 miles/150 km

>With a full load: 4 persons, luggage compartment full: approx. 30 miles/50 km.

Drive cautiously. Do not exceed a speed of 45 mph / 80 km/h. Be

aware that vehicle handling will be altered when there is a loss in inflation pressure. Anticipate, e.g., reduced tracking during braking, longer braking distances and changed steering char- acteristics. For safety reasons, BMW recommends not having damaged Run Flat tires repaired. In this case, consult your BMW center.<

Battery

Maintenance The battery is maintenance-free, that is, the original electrolyte will normally last for the service life of the battery under moderate climatic conditions.

Please consult your BMW center whenever you have any questions

concerning the battery.<

Charging the battery When charging the battery in the vehi- cle, leave the engine off at all times. Connect the charge cables to the termi- nals in the engine compartment. For terminal locations, refer to Jump-start- ing on page 159.

Disposal Return used batteries to a recy- cling point or your BMW center.

Maintain the battery in an upright posi- tion for transport and storage. Secure the battery against tilting during trans- port.<

Fuses

You will find the fuses and information on their respective allocation in the glove compartment behind a panel with two snap clips.

Do not attempt to repair a blown fuse or replace it with a fuse

having a different color or amperage rating. To do this could cause a fire in the vehicle resulting from a circuit over- load.<

Run Flat tires*

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

158

Giving and receiving assistance

Receiving assistance

The BMW Group's Mobile Service offers you 24-hour assistance in the event of a breakdown, even on week- ends and holidays.

The telephone numbers of the Mobile Service control center in your country are listed in the BMW Dealer Directory.

If your vehicle has the necessary equip- ment, you can contact the Mobile Ser- vice or issue an emergency call using buttons in the interior rearview mirror.

When an emergency call is initiated, a telephone connection is established with the general emergency call center.

In vehicles with activated BMW Assist function, a telephone connection is set up to the BMW Assist emergency call center. If the current location of your vehicle can be determined, this location is transmitted to the BMW Assist emer- gency call center.

Fold down the cover.

1 Emergency call

2 Mobile Service

Requirements for initiating an emer- gency call or contacting Mobile Service:

>The car phone is registered with a mobile network

>The emergency call system is opera- tional.

Initiating an emergency call* Press button 1 for at least 2 seconds.

The indicator lamp above the buttons lights up. As soon as a telephone con- nection has been set up to the main emergency call center, the indicator lamp flashes.

If the indicator lamp is flashing but you cannot hear the emergency call center, you may still be heard by the emer- gency call center.

For technical reasons, the emer- gency call function cannot be

guaranteed in certain unfavorable con- ditions.<

If certain requirements are met, an emergency call is automatically initiated after a serious accident. The automatic emergency call will not be hindered by pressing the button.

Mobile Service* To establish contact with the BMW Group's Mobile Service:

Press button 2 for at least 2 seconds.

The indicator lamp above the buttons lights up. As soon as a telephone con- nection has been set up with the Mobile Service, the indicator lamp flashes.

Depending on the country you are in, your vehicle's current location will also be transmitted if your vehicle is equipped with an activated BMW Assist function.

159Jump-starting

When your battery is discharged you can use two jumper cables to start your vehicle with power from the battery in a second vehicle. You can also use the same method to help start another vehicle. Only use jumper cables with fully insulated handles on the terminal clamps.

Do not touch high-voltage wiring and cables on a running engine.

Contact with components carrying high voltage can be harmful or fatal. Care- fully observe the following instructions to avoid personal injury and/or damage to one or both vehicles.<

Preparations 1. Check whether the battery of the

support vehicle has 12 volts and approximately the same capacity measured in Ah. This information is provided on the battery

2. Stop the engine of the support vehi- cle

3. Switch off all electrical components in both vehicles.

Make absolutely certain that there is no contact between the body-

work of the two vehicles, otherwise there is a short circuit hazard.<

Connecting the jumper cables Always adhere to this sequence when connecting jumper cables;

failure to observe this procedure can lead to sparks at the battery terminals and pose an injury hazard.<

The auxiliary jump-starting terminal located in your BMW's engine compart- ment acts as the positive battery termi- nal. Refer to the engine compartment overview on page, 136. The cover of this auxiliary terminal is marked with a +.

1. Open the cover of the BMW auxiliary jump-starting terminal. Do so by pull- ing the tab see arrow 1

2. Connect one terminal clamp of the plus/+ jumper cable to the positive terminal of the battery or to an auxil- iary jump-starting terminal of the support vehicle

3. Connect the second terminal clamp of the plus/+ jumper cable to the positive terminal of the battery or to an auxiliary jump-starting terminal of the vehicle to be started

4. Your BMW is equipped with a special nut see arrow 2 to serve as the ground or negatvie terminal. Attach a terminal clamp of the minus/ jumper cable to the negative terminal of the support vehicle's bat- tery or to a suitable ground on its engine or bodywork

5. Attach the second terminal clamp of the minus/ jumper cable to the neg- ative terminal of the battery or to a suitable ground on the engine or bodywork of the vehicle to be started.

Starting the engine 1. Start the engine of the support vehi-

cle and let it run for several minutes at a slightly elevated engine idle speed

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

160

2. Start the engine of the other vehicle as usual. If the first start attempt is not suc- cessful, wait a few minutes before another attempt in order to allow the discharged battery to recharge

3. Allow the engines to run for several minutes

4. Disconnect the jumper cables in reverse sequence.

Depending on the cause of the fault, have the battery checked and recharged by your BMW center.

Do not use spray starter fluids to start the engine.<

Towing the vehicle

Always comply with all applicable towing laws and regulations.<

Towing with a commercial tow truck >Use wheel lift or flat bed carrier >Do not tow with sling-type equip-

ment.

Never allow passengers to ride in a towed vehicle for any reason.

Never attach tie-down hooks, chains, straps, or tow hooks to tie rods, control arms, or any other part of the vehicle suspension, as severe damage to these components will occur, possibly lead- ing to accidents.<

Jump-starting

161

Towing the vehicle with the front axle raised Vehicles with automatic transmission:

1. Towing speed: maximum 45 mph / 70 km/h

2. Towing distance: maximum 90 miles/150 km.

Vehicles with sequential manual gear- box SMG:

While the ignition is on, move the selec- tor lever to position N, then turn off the ignition.

Towing eyelet The screw-in towing eyelet is stored in the onboard tool kit; be sure that it remains in the vehicle at all times. It can be attached at the front or rear of the vehicle. It should not be used to pull a vehicle out of deep snow, mud, sand, etc.

Always observe all applicable towing laws and regulations.

Access to tow sockets Front:

Press out the cover panel with a screw- driver inserted in the recess at the top.

Rear:

Press out the cover panel with a screw- driver inserted in the recess at the top.

Use only the towing eyelet sup- plied with the vehicle and screw it

in firmly until it stops. Use the towing eyelet for towing on paved roads only. If you do not follow these instructions, the towing eyelet could be torn out and vehicle damage could occur. Never attach tie-down hooks, chains, straps, or tow hooks to tie rods, control arms, or any other part of the vehicle suspension, as severe damage to these components will occur, possibly lead- ing to accidents.<

Towing the vehicle

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

162

Avoid staggered towing and be careful that the towing strap is

taut before starting to drive the vehicle doing the towing.<

Use only a nylon towing strap to tow the vehicle, since the inherent resil- ience of this material helps protect both vehicles from sudden jerking move- ments.

The towed vehicle should always be the lighter of the two vehicles.

If this is not the case, it will not be pos- sible to control vehicle handling.<

Tow-starting For instructions on jump-starting, refer to page 159.

Never attempt to use your vehicle to push another car, since damage to the energy-absorbing bumpers could result.

Towing the vehicle

163

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

164

165

Overview

Controls and features

Operation, maintenance

Owner service procedures

Technical data

Index

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

166 Engine data

325Ci 330Ci

Displacement Number of cylinders

cu in/cm3 152.2/2,494 6

181.8/2,979 6

Maximum power output at engine speed

hp rpm

184 6,000

225 5,900

Maximum torque at engine speed

lb ft/Nm rpm

175/237 3,500

214/290 3,500

Compression ratio 10.5 10.2

Stroke Bore

in/mm in/mm

2.95/75 3.31/84

3.53/89.6 3.31/84

Fuel mixture preparation Digital electronic engine-management system (DME)

167Dimensions

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

168 Weights

325Ci 330Ci

Curb weight

with manual transmission/SMG with automatic transmission

lbs/kg lbs/kg

3,560/1,615 3,627/1,645

3,616/1,640 3,704/1,675

Approved gross vehicle weight with manual transmission/SMG with automatic transmission

lbs/kg lbs/kg

4,442/2,015 4,509/2,045

4,497/2,040 4,575/2,075

Approved front axle load lbs/kg 2,083/945 2,094/950

Approved rear axle load lbs/kg 2,546/1,155 2,579/1,170

Approved maximum roof load for the hardtop lbs/kg 165/75 165/75

Luggage compartment capacity with the convertible top compartment raised

cu ft/l cu ft/l

9.2/260 10.6/300

9.2/260 10.6/300

Approved axle loads and approved gross vehicle weight must never be exceeded.

169Capacities

Notes

Fuel tank Reserve

gal./liters gal./liters

approx. 16.6/63 approx. 2.1/8

Fuel specification, refer to page 25

Windshield/ Headlamp washer reservoir quarts/liters approx. 5.6/5.3

Specifications, refer to page 138

Engine oil and filter change quarts/liters approx. 6.9/6.5 BMW High Performance Synthetic Oil Specifications, refer to page 138

Manual and automatic transmission and differential Lifetime lubricant, no oil change required

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

170

171

Overview

Controls and features

Operation, maintenance

Owner service procedures

Technical data

Index

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Everything from A to Z

A ABS Antilock Brake

System 125 indicator lamp 19

Acceleration assistant 78 Accessories, refer to For

your own safety 5 Accident, refer to Emer-

gency call 158 Activated-charcoal filter 110 Adaptive headlights 98 Adding brake fluid 141 Additional sources of infor-

mation 4 Air conditioning 102 Air conditioning mode 104

automatic climate control 108

Air distribution air conditioning 104 automatic climate control 108

Air distribution, individual 108

Air outlets, refer to Ventila- tion 102, 106

Air pressure, refer to Tire inflation pressure 25, 129

Air recirculation, refer to Recirculated-air mode 104, 109

Air supply air conditioning 104 automatic climate control 108

Air, drying, refer to Air con- ditioning mode 104, 108

Airbags 61 deactivating 64 indicator lamp 18, 63 sitting safely 52

Airing out, refer to Ventila- tion 102, 106

AKI, refer to Fuel specifica- tions 25

Alarm system 38 avoiding unintentional alarms 39

All-season tires, refer to Winter tires 132

Antifreeze 140 coolant 140 washer fluid 138

Antilock Brake System (ABS) 125 indicator lamp 19

Anti-theft system 30 Anti-theft warning system,

refer to Alarm system 38 Approved axle loads, refer

to Weights 168 Approved gross weight,

refer to Weights 168

Armrest 114 Artificial leather, refer to the

Caring for your vehicle brochure

Ashtray front 115 rear 116

Assistant systems, refer to Dynamic Stability Control (DSC) 93

AUC Automatic recircu- lated-air control 109

AUTO program, refer to Automatic air distribution 108

Automatic air distribution 108 air supply 108 cruise control 84 headlamp control 97

Automatic car wash, refer to the Caring for your vehicle brochure

Automatic climate control 106

Automatic curb monitor 58 Automatic dimming, interior

rearview mirror 60 Automatic recirculated-air

control (AUC) 109

Automatic transmission with Steptronic 79 indicator lamp 19, 81 interlock 71 selector lever lock 79 shiftlock 79

Automatic windshield washer, refer to Rain sen- sor 83

Average fuel consumption 91

Average speed 91 Avoiding unintentional

alarms 39 Axle loads, refer to

Weights 168

B Backrest

unlock 55 Backrest, refer to Seat

adjustment 53 Backup lamps 74

bulb replacement 151 Bandages, refer to First-aid

kit 23 Bar, towing 161

Everything from A to Z 173

Battery 157 charge 157 disposal 157 indicator lamp 18 jump-starting 159 remote control 30, 31

Battery charge current 18 Belts, refer to Safety

belts 56 Beverage holders 115 Blower

air conditioning 104 automatic climate control 108

BMW High Performance Synthetic Oils 139

BMW Maintenance System 142

BMW sports seat 53 Bore, refer to Engine

data 166 Bottle holders, see Bever-

age holders 115 Brake fluid 141

indicator lamp 18, 141 level 141

Brake force display 96 Brake hydraulic system 126 Brake lamps

bulb replacement 151 indicator lamp, defective lamp 88

Brake lights brake force display 96

Brake pads 126 brake fluid level 18, 126, 141 breaking in 124 disc brakes 126 indicator lamp 19

Brake rotors brake system 126 breaking in 124

Brake wear warning indicator lamp 19

Brakes ABS 125 brake fluid 141 breaking in 124 indicator/warning lamp 18, 19 parking brake 73

Break-in procedures 124 Bulb replacement, refer to

Lamps and bulbs 149 Bulb, replacing 149 Buttons in steering wheel 22

C California Proposition

65 warning 143 Can holders, see Beverage

holders 115 Capacities 169

Car battery 157 Car care, refer to the Caring

for your vehicle brochure Car keys, refer to Keys 30 Car radio, refer to the

Owner's Manual for Radio Car telephone

preparation 115 Car telephone, refer to the

separate Owner's Manual Car vacuum cleaner, con-

necting 116 Car wash, refer to the Caring

for your vehicle brochure Carpet care, refer to the

Caring for your vehicle brochure

Cassette operation, refer to the Owner's Manual for Radio/Onboard Computer

CBC Cornering Brake Con- trol 125 warning lamp 19

CD changer, refer to the Owner's Manual for Radio/Onboard Computer

CD operation, refer to the Owner's Manual for Radio/Onboard Computer

Cellular phone 115 Center armrest

front 114

Center high-mount brake lamp bulb replacement 152

Central locking system 30 button 34 passenger compartment 34

Changing a wheel 153 Charge indicator lamp 18 Check Control 88 Check Gas Cap

indicator lamp 19 Child seats, refer to Child-

restraint systems 64 Child-restraint mounting

system (LATCH) 66 Child-restraint system 64 Chock 154 Cigarette lighter 115 Cigarette lighter socket 116 Cleaning chrome parts, refer

to the Caring for your vehi- cle brochure

Cleaning light alloy wheels, refer to the Caring for your vehicle brochure

Cleaning position, convert- ible top 45, 50

Cleaning the vehicle, refer to the Caring for your vehicle brochure

Cleaning windshield 84

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Everything from A to Z

Clock 89 12-/24-hour mode 89 setting, refer also to the Owner's Manual for Radio/Onboard Computer

Closing from inside 34 from outside 31

Clothes hooks 125 Clutch

breaking in 124 Cockpit 14 Code, refer to the Owner's

Manual for Radio/Onboard Computer

Coin box 115 Cold start, refer to Starting

the engine 71 Compact disc operation,

refer to the Owner's Man- ual for Radio/Onboard Computer

Compartments 114 Compression ratio, refer to

Engine data 166 Computer 90 Condensation, refer to Air

conditioning mode 104, 108

Configuring settings, refer to Vehicle Memory, Key Memory 70

Connecting a vacuum cleaner, refer to Cigarette lighter 116

Consumption display 86

Consumption, refer to Aver- age fuel consumption 91

Control elements, refer to Cockpit 14

Convenience operation from outside 33 windows 32

Convertible top cleaning position 45, 50 closing in an emergency 48 electrical fault 48 indicator lamps 47 remote control 31

Convertible top activation fully automatic top 46 manual top 41

Convertible top compart- ment panel 37

Coolant 140 indicator lamp 19, 87 level 140 temperature gauge 87

Coolant water, refer to Cool- ant 140

Cooling, refer to Tempera- ture 104, 108

Copyright 4 Cornering Brake Control

(CBC) 125 warning lamp 19

Correct tires 132 Cruise control 84

indicator lamp 20 Cup holders, see Beverage

holders 115 Curb weight, refer to

Weights 168 Current consumption, refer

to Energy control 86 Curve lighting, refer to

Adaptive headlights 98 Cylinders, refer to Engine

data 166

D Dashboard, refer to

Cockpit 14 Data

capacities 169 dimensions 167 engine 166 technical 166 weights 168

Daytime driving lamps 97 DBC Dynamic Brake Control

19, 125 Deep water, refer to Water

on roadways 125

Defrost position, refer to Defrosting windows 105, 108

Defrosting and demisting windows air conditioning 105 automatic climate control 108

Defrosting windows 105, 108

Defrosting windshield, refer to Defrosting windows 105, 108

Demisting windows air conditioning 105 automatic climate control 108

Determining the maximum load 118

Differential breaking in 124

Digital clock 89 Dimensions 167 Dipstick, engine oil 138 Disc brakes 126 Displacement, refer to

Engine data 166 Display lighting, refer to

Instrument lighting 98 Displays, refer to Instrument

cluster 16

Everything from A to Z 175

Disposal oil 139 vehicle battery 157

Distance warning, refer to Park Distance Control (PDC) 92

Door key 30 Door lock 33 Doors

emergency operation 33 Draft-free ventilation

105, 109 Driving light, refer to Parking

lamps/Low beams 97 Driving notes 125 Dry air, refer to Air condi-

tioning mode 104, 108 DSC Dynamic Stability Con-

trol 93 indicator lamp 19, 93

DTC Dynamic Traction Con- trol 93 indicator lamp 19, 93

Dynamic Brake Control (DBC) 19, 125 indicator lamp 19

Dynamic Stability Control (DSC) 19, 93

Dynamic Traction Control (DTC) 93 indicator lamp 19, 93

E Easy entry, refer to Entering

the rear 55 Electric power windows 40 Electrical accessories, fail-

ure 157 Electrical malfunction

automatic transmission with Steptronic 81 door lock 33 driver's door 33 fuel filler door 24 luggage compartment lid 35

Electronic Stability Program (ESP), refer to Dynamic Stability Control (DSC) 93

Emergency call 158 Emergency operation

closing the convertible top 48 doors 33 driver's door 33 fuel filler door 24

Emergency release luggage compartment lid 35, 36

Emissions, minimum, refer to Energy control 86

Energy control 86

Engine breaking in 124 data 166 electronics 19 indicator lamp 19 speed 86, 166 starting 71 switching off 73

Engine compartment 136 Engine coolant 140

adding 140 Engine oil

adding 139 additives, refer to Adding engine oil 139 capacity 169 consumption 138 indicator/warning lamp 19 quality 139 specified oils 139 viscosity 139

Engine oil level 19 check 138 indicator/warning lamp 18

Engine oil pressure indicator/warning lamp 18

Engine oil types 139 Engine output, refer to

Engine data 166 Engine speed 86, 166 Entering the rear 55

Environmentally-friendly driving, refer to Energy control 86

Equipment range, refer to the Service and Warranty Information Booklet for US models / Warranty and Service Guide Booklet for Canadian models

ESP Electronic Stability Pro- gram, refer to Dynamic Stability Control (DSC) 93

Exterior mirrors 59 Eyelets, towing 161

F False alarm, refer to

Avoiding unintentional alarms 39

Fasten safety belts warning lamp 18, 56

Fault displays 88 Filling the windshield washer

reservoir 169 First aid, refer to First-aid

kit 23 First-aid kit 23 Flashlight 111 Flashlight, refer to

Rechargeable flashlight 111

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Everything from A to Z

Flat tire 153 Flat Tire Monitor 94 space-saver spare tire 153

Flat Tire Monitor 94 indicator lamp 18, 19, 95

Flat tire, refer to Tire condi- tion 129

Fluid reservoir for washer systems 138

Fog lamps 99 indicator lamp 20

Follow me home lamps 97 Footbrake, refer to General

driving notes 125 Front airbags 61 Front fog lamps 99 Front seat adjustment 53 Fuel

display 87 quality 25 volume 169

Fuel consumption display 91

Fuel display, refer to Fuel gauge 87

Fuel economy, refer to Energy control 86

Fuel filler door 24 release following an elec- trical malfunction 24

Fuel level indicator, refer to Fuel gauge 87

Fuel mixture preparation 166 Fuel reserve indicator, refer

to Fuel gauge 87 Fuel tank capacity 169 Fully-automatic convertible

top 46 activation 46 convenience operation 32, 33 opening, closing 47 remote control 32

Fuses 157

G Garage door opener, refer to

Integrated universal remote control 112

Gasoline consumption, refer to Average fuel consump- tion 91

Gasoline, refer to Fuel spec- ifications 25

Gear indicator 77, 81 Gear lever

automatic transmission with Steptronic 79 sequential manual gear- box SMG 75

Gearbox manual transmission 74

Gearshift lever manual transmission 74

General driving notes 125 Glove compartment 111 Grills, refer to Ventilation

102, 106 Gross weight, refer to

Weights 168

H Handbrake, refer to Parking

brake 73 Hardtop 127 Hardtop preparation 127 Hardtop, refer to the sepa-

rate Owner's Manual 127 Hazard warning flashers 14 Hazard warning triangle 23 Head restraints 54 Headlamp cleaning system

cleaning headlamps 84 washer fluid 138, 169

Headlamp control, auto- matic 97

Headlamp flasher 99 indicator lamp 21

Headlamps bulb replacement 149 care, refer to the Caring for your vehicle brochure

Heated mirrors 59

Heated rear window air conditioning 104 automatic climate control 109

Heated seats 58 Heating

exterior mirrors 59 rear window 104, 109 seats 58

Heating and ventilation 102, 106

Heavy loads, refer to Cargo loading 119

Height adjustment seats 53 steering wheel 59

Height, refer to Dimensions 167

High beams 82, 83, 99 bulb replacement 150 headlamp flasher 99 indicator lamp 21

Holder for beverages 115 Hood release 134 Horn 14 Hub cap 154 Hydraulic brake assistant,

refer to DBC 125 Hydraulic system

brakes 126 Hydroplaning 125

Everything from A to Z 177

I Ice warning 90 Ignition 71 Ignition key 30

positions 71 Ignition lock 71 Imprint 4 Indicator lamps 18 Indicator/warning lamp

airbags 18 alarm system 39 brakes 18, 19 Check Gas Cap 19 coolant 19, 87 DSC 19 Fasten safety belts 18 Flat Tire Monitor 18, 19, 95 fog lamps 20 reserve 87 rollover protection system 19 Service Engine Soon 19

Individual air distribution 108 Individual settings, refer to

Vehicle Memory, Key Memory 70

Inflation pressure monitor- ing, refer to Flat Tire Moni- tor 94

Inflation pressure, tires 25, 129

INSPECTION 88 Instrument cluster 16 Instrument lighting 98 Instrument panel 14 Integrated universal remote

control 112 Interface socket for onboard

diagnostics (OBD) 143 Interior lamps 100

remote control 32 Interior motion sensor 38

switching off 32, 39 Interior rearview mirror 60

automatic dimming feature 60

Interior temperature, adjust- ment 104, 108

Interlock, refer to Steering wheel lock 71

Intermittent mode, wipers 83

Interval display, service 88

J Jack 153 Jacking points 154 Jump-starting 159

K Key Memory 70

Keys 30 with remote control 30

Kickdown 76, 80

L Lamp defect 149 Lamps and bulbs 149 Lashing down loads, refer to

Cargo loading 118 Lashing eyelets, refer to

Securing cargo 120 Lashing fittings, refer to

Securing cargo 120 LATCH child-restraint

mounting system 66 Leather care, refer to the

Caring for your vehicle brochure

LEDs light-emitting diodes 100

Length, refer to Dimensions 167

License plate lamp bulb replacement 153

Light switch 97 Light-emitting diodes

(LEDs) 100 Lighter 115 LIGHTS ON warning 97 Lights, refer to Parking

lamps/Low beams 97

Load, refer to Cargo loading 118

Loading vehicle 118

Load-securing devices 120 Lock buttons on doors, refer

to Locking 34 Lock, steering wheel 71 Locking

from inside 34 from outside 31, 33

Locking and unlocking doors from inside 34 from outside 31, 33

Low beams 97 automatic 97 bulb replacement 149 indicator lamp, defective lamp 88

Lug bolts key 154 torque 154

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Everything from A to Z

Luggage compartment capacity 168 emergency operation, refer to Manual operation 35 enlarge volume 37 floor panel 37 lid 35 opening from outside 35 opening, remote control 32 opening/closing, refer to Luggage compartment lid 35 remote control 32 volume 168

Luggage compartment lid 35 emergency operation 35 emergency release 36 indicator lamp 88 opening from inside the vehicle 35 opening from outside 35 remote control 32 securing separately 35 unlocking manually 35

Luggage compartment light- ing 35

Luggage rack, refer to Roof- mounted luggage rack 121

Lumbar support 54

M Maintenance 88, 142 Maintenance system 142 Making telephone calls,

refer to the telephone Owner's Manual

Malfunction convertible top 48 door lock 33 fuel filler door 24

Malfunction displays 88 Manual convertible top 41

closing 44 opening 42 operation 41

Manual operation door lock 33 driver's door 33 fuel filler door 24 luggage compartment lid 35 power convertible top 48

Manual transmission 74 Master keys 30 MC operation, refer to the

Owner's Manual for Radio/Onboard Computer

MD operation, refer to the Owner's Manual for Radio/Onboard Computer

Memory, refer to Seat and mirror memory 57

Memory, refer to Vehicle Memory, Key Memory 70

Microfilter air conditioning 105 automatic climate control 110

Microphone, refer to Cellular phone 115

Mini disc operation, refer to the Owner's Manual for Radio/Onboard Computer

Mirrors 59 heated 59 memory, refer to Seat and mirror memory 57

Mobile Service 158 Modifications, technical,

refer to For your own safety 5

Multifunction steering wheel 22

Multifunction switch turn signal indicator/head- lamp flasher 82, 83

N Navigation system, refer to

the Owner's Manual for Radio/Onboard Computer

Neck restraints, refer to Head restraints 54

Nets 114

Nozzles, refer to Ventilation 102, 106

Nylon rope, refer to Towing the vehicle 161

O OBD interface socket 143 Odometer 86 Oil

additives, refer to Adding engine oil 139 capacity 169 dipstick 138 quality 139 specified engine oils 139 viscosity 139

Oil change intervals, refer to Service interval display 142

Oil change intervals, refer to the Service and Warranty Information Booklet for US models/Warranty and Ser- vice Guide Booklet for Canadian models

Oil consumption 138 Oil dipstick 138 Oil filter change 169 Oil level

checking 138 indicator lamp 18

Everything from A to Z 179

Oil pressure indicator lamp 18

OIL SERVICE 88 Oil types 139 Old batteries, refer to Dis-

posal 157 Onboard computer 90 Onboard computer, refer to

the Owner's Manual for Onboard Computer

Onboard tool kit 148 Opening and closing

from outside 31 from the inside 34 via the door lock 33 via the remote control 31

Outlets, ventilation 102, 106 Outside temperature dis-

play 90 changing unit of measure 90

P Paintwork care, refer to the

Caring for your vehicle brochure

Panic mode, trigger alarm 32

Park Distance Control (PDC) 92

Parking aid, refer to Park Distance Control (PDC) 92

Parking brake 73 indicator lamp 18

Parking lamps 97 bulb replacement 150

Parking lamps/Low beams 97

Parts and accessories, refer to Your individual vehicle 5

Passenger-side exterior mir- ror tilt function 58

PDC Park Distance Control 92

Plastic, refer to the Caring for your vehicle brochure

Pollen, refer to Microfilter 105

Pollen, refer to Microfil- ter/activated-charcoal fil- ter 110

Power output, refer to Engine data 166

Power seat 53 Power socket, cigarette

lighter 116 Pressure monitoring, tires

Flat Tire Monitor 94 Pressure, tires 25, 129 Protective function

electric power windows 41

R Radio remote control key,

refer to Master key with remote control 30

Radio, refer to the Owner's Manual for Radio

Rain sensor 83 Raising the floor panel 37 Range 91 Reading lamps

front 100 rear 100

Rear lamps bulb replacement 151 indicator lamp, defective lamp 88

Rear window defroster air conditioning 104

Rear window heating automatic climate control 109

Rear-entry assist 55 Rearview mirror 59 Receiving assistance 158 Recirculated-air mode

air conditioning 104 automatic climate control 109

Recirculating the air, refer to Recirculated-air mode 104, 109

Reclining seat, refer to Seat adjustment 53

Refueling 24 fuel filler door 24

Releasing hood 134

Remaining distance to ser- vice 88

Remaining distance, refer to Range 91

Remote control 31 garage door opener 112 luggage compartment lid 32 malfunction 32

Replacement key 31 Replacing lamps, refer to

Lamps and bulbs 149 Replacing tires 130 Reporting safety defects 7 Restraint systems

for children 64 Restraint systems, refer to

Safety belts 56 Reverse

automatic transmission with Steptronic 79 SMG gearbox 76

Reverse gear manual transmission 74

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Everything from A to Z

Rollover protection system 68 indicator lamp 19 lowering 68

Roof load capacity 168 Roof-mounted luggage

rack 121 Rope, refer to Towing the

vehicle 161 Run Flat tires 131, 156

S Safe seating position 52 Safety belt height adjust-

ment 56 Safety belts 56

seat-integrated safety belt system 55 sitting safely 52 warning lamp 18

Safety systems, refer to Antilock Brake System 125 Dynamic Stability Control (DSC) 93

Screwdriver, refer to Onboard tool kit 148

Seat adjustment 53 BMW sports seat 53 power 53

Seat belt tensioner, refer to Safety belts 56

Seat heating 58 Seat memory, refer to Seat

and mirror memory 57 Seat positions, storing 57 Seats 53 Securing cargo 120 Securing child-restraint sys-

tem 66 Securing the vehicle

from inside 34 from outside 31, 33

Selector lever automatic transmission 79 sequential manual gear- box SMG 75

Selector lever lock, refer to Shiftlock 75, 79

Selector lever positions automatic transmission 79 sequential manual gear- box SMG 75

Sequential manual gearbox SMG 75 indicator lamp 19

Service and Warranty Infor- mation Booklet 142

Service Engine Soon warning lamp 19

Service interval display 88, 142

Shift paddles 76

Shifting gears automatic transmission with Steptronic 79 sequential manual gear- box SMG 76

Shiftlock 75 Shiftlock, refer to Range

selection 79 Side airbags 61 Side turn signal indicators

bulb replacement 151 Sitting safely

with airbags 52 with safety belts 52

Size 167 Ski bag 117 Slipstream deflector, refer to

Wind deflector 50 SMG sequential manual

gearbox 75 indicator lamp 19

Smokers' package, refer to Ashtray 115

Snow chains 133 SOS, refer to Emergency

call 158 Space-saver spare tire

changing a wheel 153 Spare key 30 Spare tire 153 Spare wheel 156 Special oils 139

Specified oils 139 Speed gauge, refer to

Speedometer 16 Speedometer 16 SPORT button 78 Sport program

automatic transmission with Steptronic 80

Sports seat 53 Stability control, refer to

Dynamic Stability Control (DSC) 93

Standing lamps 99 Starting difficulties

jump-starting 159 temperature 71

Starting help DSC 93 Starting the engine 71 Starting, refer to Starting the

engine 71 Status of the Owner's Man-

ual 5 Steering wheel lock 71 Steering wheel, adjusting 59 Steptronic, refer to Manual

operation 80 Storage compartments 114 Storage nets 114 Storing seat positions,

refer to Seat and mirror memory 57

Storing tires 132

Everything from A to Z 181

Stroke, refer to Engine data 166

Surface ice, refer to Ice warning 90

Switches, refer to Cockpit 14

Switching off engine 73 vehicle 73

Symbols 4 Synthetic oils 139

T Tachometer 86 Tail lamps

bulb replacement 151 Tail lamps, refer to Rear

lamps 151 Tank capacity, refer to Fuel

tank capacity 169 Tank indicator, refer to Fuel

gauge 87 Technical data 166 Technical modifications 5 Technical modifications,

refer to For your own safety 5

Telephone hookup 115 Telephone, refer to the sep-

arate Owner's Manual

Television, refer to the Owner's Manual for Onboard Computer

Temperature air conditioning 104 automatic climate control 108

Temperature adjustment 104, 108

Temperature display engine coolant 87 ice warning 90 outside temperature 90 setting units 90

Temperature layering 105, 109

Tempomat, refer to Cruise control 84

Thigh support area, adjust- ing 53

Third brake lamp, refer to Center high-mount brake lamp 152

Three-point safety belt 56 Tilt alarm sensor 32

remote control 32 switching off 32, 39

Tilting passenger-side exte- rior mirror 58

Time 89

Tire pressure monitoring, refer to Flat Tire Monitor 94

Tire replacement 130, 153 Tires

age 131 breaking in 124 changing 153 damage 129 flat 153 inflation pressure 25, 129 replacing 130 size, refer to Wheel and tire combinations 132 storing 132 tread 129 tread wear indicator, refer to Tire tread tire damage 129 winter tires 132

Tools, refer to Onboard tool kit 148

Torque engine 166 lug bolts 154

Tow sockets for towing eye- let 161

Towing bar 161 Towing eyelet 161 Towing rope 161 Towing the vehicle 161

Track width, refer to Dimen- sions 167

Transmission automatic transmission with Steptronic 79 sequential manual gear- box SMG 75

Transmission lock, refer to P Park 79

Transmission malfunction automatic transmission with Steptronic 81 sequential manual gear- box SMG 77

Transport securing devices, refer to Securing cargo 120

Transporting children safely 64

Trap protection electric power windows 41

Tread depth, refer to Tire tread 129

Tread depth, tires 129 Tread wear indicator in the

tires, refer to Tire tread tire damage 129

Trip distance recorder, refer to Trip odometer 86

Trip meter, refer to Trip odometer 86

Trip odometer 86

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Everything from A to Z

Trunk lid, refer to Luggage compartment lid 35

Trunk lighting, refer to Lug- gage compartment light- ing 35

Turn signal indicator 82, 83 bulb replacement 151 indicator lamp 20

Turn signal indicator, side bulb replacement 151

Turning circle, refer to Dimensions 167

TV function, refer to the Owner's Manual for Onboard Computer

U Underbody protection, refer

to the Caring for your vehi- cle brochure

Uniform Tire Quality Grading 131

Units average fuel consumption 91 temperature 90

Universal garage door con- trol, refer to Integrated universal remote control 112

Universal remote control 112

Unlocking from inside 34 from outside 31, 33

V Valve

screw caps 154 Vehicle

battery 157 break-in procedures 124 dimensions 167 loading 118 starting 71 switching off 73 washing, refer to the Car- ing for your vehicle bro- chure 83 weight 168

Vehicle Memory 70 Vehicle weight 168 Ventilation 102, 106

draft-free 105, 109 Voice Input System 22 Voice recognition, refer to

separate Owner's Manual Volume

luggage compartment 168

W Warning and indicator

lamps 18

Warning lamp 'Fasten safety belts' 18

Warning messages 88 Warranty and Service Guide

Booklet 142 Warranty, refer also to sepa-

rate booklet 7 Washer fluid

adding 138, 169 Washer fluid reservoir 138

volume 138 Washer jets, refer to Wind-

shield washer jets 84 Washer/wiper system 84

washer fluid 138 Waste tray, refer to

Ashtray 115 Water on roadways, deep

water 125 Weights 168 Wheel and tire

combinations 132 Wheelbase, refer to Dimen-

sions 167 Wheels and tires 132 Wheelslip control DSC 93 Width, refer to

Dimensions 167 Wind deflector 50 Window condensation

removing 105, 108

Windows convenience operation 32, 33 power 40 remote control 31, 32

Windshield washer nozzles 84

Windshield washer reservoir volume, see Capacities 169

Winter tires 132 storing 132

Wiper blades, replacing 148 Work in the engine compart-

ment 134 Wrench, refer to Onboard

tool kit 148

X Xenon lamps

bulb replacement 150

183

Ov er

vi ew

Co nt

ro ls

M ai

nt en

an ce

Re pa

ir s

Da ta

In de

x

Refueling

To ensure that you always have conve- nient access to all essential information when you stop for fuel, we recommend that you fill out the adjoining chart by entering the data that apply to your vehicle. Consult the index for individual specifications.

Fuel

Please enter your preferred fuel here.

Engine oil

The oil volume between the two marks on the dipstick corresponds to approx. 1.1 US quarts/1 liter.

Tire inflation pressure

Designation

Quality

Summer tires Winter tires

Front Rear Front Rear

Up to 2 persons

4 persons plus luggage

More about BMW

bmwusa.com Th

Manualsnet FAQs

If you want to find out how the 3 Series BMW works, you can view and download the BMW 325Ci Convertible 3 Series 2004 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for BMW 3 Series as well as other BMW manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a BMW 3 Series. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the BMW 325Ci Convertible 3 Series 2004 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This BMW 325Ci Convertible 3 Series 2004 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download BMW 325Ci Convertible 3 Series 2004 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print BMW 325Ci Convertible 3 Series 2004 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the BMW 325Ci Convertible 3 Series 2004 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.