Blaupunkt 5DA39258AU Instructions for Installation and Use PDF

1 of 12
1 of 12

Summary of Content for Blaupunkt 5DA39258AU Instructions for Installation and Use PDF

Instructions for installation and use

5DA39258AU

22

INDEX SAFETY INFORMATION......................................................................................................................................................... 3

CHARACTERISTICS ............................................................................................................................................................. 6

INSTALLATION...................................................................................................................................................................... 7

USE ........................................................................................................................................................................................ 9

CARE AND CLEANING ....................................................................................................................................................... 10

SAFETY INFORMATION

For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance.

The wire connection has to be done by specialized technician.

The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.

The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).

If the instructions for installation for the gas hob specify a greater distance, this must be respected.

Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.

Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

For Class I appliances, check that the domestic power supply guarantees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route of the flue must be as short as possible.

Regulations concerning the discharge of air have to be fulfilled.

Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).

If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.

The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

If the supply cord is damaged, it must be replaced from the manufac- turer or its service agent.

Connect the plug to a socket complying with current regulations, lo- cated in an accessible place.

With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations pro- vided by the local authorities.

WARNING: Before installing the Hood, remove the protective films.

Use only screws and small parts in support of the hood.

WARNING: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

Do not look directly at the light through optical devices (binoculars, magnifying glasses).

Do not flamb under the range hood; risk of fire.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and under- stand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Children should be supervised to ensure that they do not play with the appliance.

The appliance is not to be used by persons (including children) with re- duced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

Accessible parts may become hot when used with cooking appliances.

Clean and/or replace the Filters after the specified time period (Fire hazard). See paragraph Care and Cleaning.

There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of elec- trical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed informa- tion about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you pur- chased the product.

CHARACTERISTICS

Components Ref. Q.ty Product Components

1 1 Hood Body, complete with: Controls, Light, Blower, Fil-

ters

8 1 Directional Air Outlet grille

20 1 Closing element

Ref. Q.ty Installation Components

12a 4 Screws 4,2 x 44,4

12b 2 Screws 4,2 x 12

12e 2 Screws 2,9 x 9,5

Q.ty Documentation

1 Instruction Manual

12b

INSTALLATION

Drilling the Support surface and Fitting the Hood

SCREW FITTING

The hood support surface must be 135 mm above the bot-

tom surface of the wall units.

Drill the support with a 4,5 mm drill bit, using the drill-

ing template provided.

Cut a hole 125 mm in size on the support surface, using

the drilling template provided.

Fix using the 4 screws 12a (4,2 x 44,4) provided.

12a

1 3 5

125

SNAP-ON FITTING

The hood can be installed either directly on the bottom sur-

face of the wall units using snap-on side supports.

Cut a fitted opening in the bottom surface of the wall unit,

as shown.

Insert the hood until the side supports snap into place.

Lock in position by tightening the screws Vf from under-

neath the hood.

CLOSING ELEMENT

The space between the edge of the hood and the rear wall

can be closed by applying the element 20 provided, using

the screws 12b.

20

12b

Connections DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to

the chimney using either a flexible or rigid pipe 120

mm, the choice of which is left to the installer.

Fix the pipe in position using sufficient pipe clamps

(not supplied).

Remove any activated charcoal filters.

120

RECIRCULATION VERSION AIR OUTLET

Cut a hole 125 mm in any shelf that may be posi-

tioned over the hood.

Connect the flange to the outlet on the shelf over the

hood using a flexible or rigid pipe 120 mm.

Fix the pipe in position using sufficient pipe clamps

(not supplied).

Fix the directional grille 8 on the recirculation air

outlet using the 2 screws 12e (2,9 x 9,5) provided.

Ensure that the activated charcoal filters have been

inserted.

12e

8

9

125

ELECTRICAL CONNECTION

Connect the hood to the mains through a two-pole switch having a contact gap of at least 3

mm.

When opening the sliding carriage for the first time after installing the hood, pull it out

briskly until it clicks.

USE Control panel

L

M - V

0 1

0

1

2 3

L Light Switches the lighting system on and off.

M Motor Switches the extractor motor on and off.

V Speed Sets the operating speed of the extractor:

1. Low speed, used for a continuous and silent air change in the presence

of light cooking vapour.

2. Medium speed, suitable for most operating conditions given the opti-

mum treated air flow/noise level ratio.

3. Maximum speed, used for eliminating the highest cooking vapour

emission, including long periods.

CARE AND CLEANING

Grease filters

CLEANING METAL CASSETTE GREASE FILTERS

The filters must be cleaned every 2 months, or more frequently in case of particularly heavy use of the hood. Filters can be washed in a dishwasher.

Pull out the sliding suction panel. Remove the filters one by one, after having disconnected the

relative fastening elements. Wash the filters, taking care not to bend them. Let them get dry

before refitting them. (The colour of the filter surface may change throughout the time but this has no influence to the fil- ter efficiency).

When refitting the filters, make sure that the handle is visible on the outside.

Close the sliding suction panel.

Charcoal filter (Recycling version)

REPLACING CHARCOAL FILTERS

Warning: Turn the lights off and wait until the lamps cool down

before you change the odour filter.

These filters are not washable and cannot be regenerated, and

must be replaced approximately every four months or more

frequently by particularly heavy use.

Pull out the sliding suction panel.

Remove the grease filters.

Remove the saturated carbon filter by releasing the fixing

hooks

Fit the new filter by hooking it into its seating.

Replace the grease filters.

Close the sliding suction panel.

WORKTOP ILLUMINATION

If a lamp fails to function at any time, open the metal grille panel and check that the lamp is fully screwed into the holder. When changing the lamp, an identical replacement must be fitted to ensure a safe working of the hood.

Lamp Power (W) Socket Voltage (V) Dimension (mm) ILCOS Code

4 E14 220-240 107 x 37 DRBB/F-4-220-240-E14-35/100

5 GU10 230 52 x 50 DRPAR-5/840-220/240-GU10-35/36

DRPAR-5/830-220/240-GU10-35/36

Manualsnet FAQs

If you want to find out how the 5DA39258AU Blaupunkt works, you can view and download the Blaupunkt 5DA39258AU Instructions for Installation and Use on the Manualsnet website.

Yes, we have the Instructions for Installation and Use for Blaupunkt 5DA39258AU as well as other Blaupunkt manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instructions for Installation and Use should include all the details that are needed to use a Blaupunkt 5DA39258AU. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Blaupunkt 5DA39258AU Instructions for Installation and Use is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Blaupunkt 5DA39258AU Instructions for Installation and Use consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Blaupunkt 5DA39258AU Instructions for Installation and Use free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Blaupunkt 5DA39258AU Instructions for Installation and Use, simply download the document to your computer. Once downloaded, open the PDF file and print the Blaupunkt 5DA39258AU Instructions for Installation and Use as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.