Contents

Blaupunkt 5GH75BB490 Instruction Manual PDF

1 of 17
1 of 17

Summary of Content for Blaupunkt 5GH75BB490 Instruction Manual PDF

esLAUPUNKT

lnstruction manual

5GH65BB390

5GH65BB490

5GH75BB390

5GH75BB490

5GH85BB390

5GH85BB490

5GH85BB590

Gas-Hobs

These instructions have been drawn up for your safety and that of others. You

are therefore requested to read them carefully before installing and using the

appliance. Keep this instruction manual for future reference as necessary. If the

appliance is sold or moved, make sure that the manual is handed over to the new

user.

Installation

Installation of the appliance and its connection to the electrical mains must only be

carried out by QUALIFIED PERSONEL. Before any procedure, it is important to

check that the appliance is DISCONNECTED from the electrical mails.

It is risky to modify or attempt to modify the characteristics of this product.

After removing the appliance from the packaging, make sure that it is undamaged

and that the electrical lead is in perfect condition. Otherwise, contact your dealer

before putting the appliance into operation.

The Manufacturer declines all responsibility in case of failure to comply with the

accident prevention regulations.

Make sure that air is able to circulate freely around the appliance. Poor ventilation

produced a shortage of oxygen

Make sure that the appliance is supplied with the type of gas indicated on the

relative sticker next to the mains gas connection pipe.

Use of a gas cooking appliance produces heat and moisture in the room in which it

is installed. Ensure that the room is well ventilated by keeping the air intakes open

and in good working order or by installing an extractor hood with discharge pipe.

If the appliance is used intensively for a long time the effectiveness of the

ventilation will have to be increased, for example by opening a window or

increasing the power of any electric extractor fan.

During use

This product is designed to cook food inside ordinary homes and for

non-professional purposes. It should not be used for any other purpose.

After using the appliance, make sure that all controls are in CLOSED or OFF

position.

If you use an electrical socket close to this appliance, take care that the cables of the

appliances you are using are far away from the hot parts of this appliance.

1

Childrens safety

This appliance must only be used by adults. Make sure that children do not touch

the controls or play with the appliance.

The exposed parts of this appliance heat up during cooking and remain hot for some

time even after it is switched off. Keep children well away until the appliance has

cooled down.

Cleaning and maintenance

Keep the appliance thoroughly cleaned. Food residues may cause fire risks.

Service and parts

In the instance of malfunctions. Never attempt to repair the appliance yourself.

Repairs by unskilled persons may cause damage and accidents. First refer to the

contents of this manual. If you do not find the necessary information, contact your

nearest Service Centre. Servicing work on this appliance must be carried out by an

authorized Technical Service Centre. Always request the use of original spare

parts.

Environmental protection advice

All the materials used are environmentally compatible and recyclable. Please make

your contribution to conserving the environment by using the separate waste

collection channels available.

Decommissioned appliances

Appliances which are no longer used or usable are not worthless waste. Through

environment-friendly disposal, a number of materials used in the production of

your appliance can be recovered.

Find out about the current disposal options from your specialist dealer, or your

local authority.

Before scrapping the appliances, cut the power supply lead and make it unusable.

2

Contents

For the User

For your safety 2

Description of the hob 4

Instructions for use 4

Cleaning and maintenance 6

For The Installation Technician

Technical data 8

Instructions for the installation technician 9

Electrical connection 11

Adapting to the different types of gas 12

Building into fitted kitchen units 13

Guide to reading the instructions

The following symbols will help you

When reading the instructions:

Safety information

Step by step instructions

Suggestions and Advice

Information concerning environmental protection

This appliance complies with the following EEC Directives:

- 73/23 and 90/683 (relating to Low Voltage);

- 89/336 (relating to Electromagnetic Compatibility);

- 90/396 (relating to Gas Appliances);

- 93/68 (relating to the General Standards )

And subsequent amendments.

3

Description of the hob

1

Instructions for use

The hob control knobs

The symbols on the control knobs mean the following:

no gas flow

maximum gas flow

Minimum gas flow

All operating positions must be set between the maximum and minimum flow settings, and never between the maximum setting and the closed position.

(Symbol present on version with lighting A-Burner cap

integrated in the Control knob) B-Lighting plug

C-Thermocouple

D-Triple flame cap

Dual triple flame version

no gas flow

maximum gas flow from central burner

minimum gas flow from central burner

maximum gas flow from outer and central burners simultaneously

minimum gas flow from outer and central burners simultaneously 4

Lighting the burners

To obtain a flame more easily, light the burner before placing a cooking

utensil on the pan stand

To light a burner, proceed as follow: for Version with lighting integrated in

the

control knob push the knob of the burner fully down and turn it

anticlockwise

to the maximum flow setting symbol, or press the button if the appliance

has individual lighting.

After lighting the flame, keep the knob pressed for about 10 seconds: this

time is necessary to heat up the thermocouple(Fig.1-C) and activate the

safety valve, which would otherwise cut off the gas flow.

Then check that the flame is even and turn the control knob to adjust the flame

as required

In the instance of a power cut, place a flame near the burner and proceed as

already described.

If the flame does not light after a few attempts, check that the burner cap and

flame cap are correctly positioned.

To turn off the flame, turn the control knob clockwise to the symbol.

Before removing pans from the burners, always lower or turn off the

flame.

For correct use of the hob

For lower gas consumption and better efficiency: Use only flat-bottomed pans of

dimensions suitable for the burners, as shown in the table on the right. Also, as soon

as a liquid comes to the boil take care to turn the flame down to a level that will just

keep it boiling.

Burner minimum diameter maximum diameter

Large(rapid) 180mm 220mm

Medium(semi-rapid) 120mm 200mm

Small(Auxiliary) 80mm 160mm

Triple Flame 220mm 260mm

During cooking processes involving fats or oils, watch your foods

carefully because these substances may catch fire if brought to high

temperatures.

5

Cleaning and maintenance Before each operation, disconnect the appliance from the electrical mains and allow it

to cool down.

General cleaning

Wash enameled parts with lukewarm water and detergent: do not use abrasive

products which might damage them.

Wash the flame caps and burner caps often with boiling water and detergent, taking

care to remove all deposits

The hob pan stands can also be washed in a dishwasher

For stubborn dirt, use ordinary non-abrasive detergents or specific commercial

products. We strongly advise you not to use scouring pads. Steel wool or acids for

cleaning.

Hob

Clean the hob regularly with a soft cloth wet with lukewarm water and a little liquid

detergent. Do not use the following products:

- household detergents or bleaches;

- soaped scouring pads not suitable for non-stick utensils;

- steel wool scouring pads;

- stain removers for baths or sinks.

If the hob gets very dirty, use specific commercial products.

Ignition plug

Automatic burner ignition is provided (when installed) by a ceramic plug and a

metal electrode (B in fig.1). Periodically clean these parts of the hob thoroughly. In

addition, to avoid ignition difficulties, check that the cavities in the burner are not

obstructed.

To remove deposits from the burner cavities,

remove the cap and separate the two parts

(see diagram on the right). After cleaning,

put the two parts back together and return

them correctly to their position. After washing,

replace the hob pan stands, checking that they

are correctly positioned.

6

Routine maintenance

Have the condition and efficiency of the gas pipe and the pressure regulator (if

installed) checked periodically. If anomalies are found, do not repairs but have the

faulty part replaced.

To ensure good performance and safety, the gas regulator taps must be greased

periodically.

Periodic lubrication of the taps must only be carried out by qualified

personel, who must also be contacted if the appliance malfunctions.

Service and parts

Before leaving the factory, this appliance was tested and adjusted by specialist skilled

staff to give the best operating results. Any subsequent necessary repairs or

adjustments must be carried out with the greatest care and attention.

For this reason, we strongly advise you always to contact the Dealer who sold you the

appliance or our nearest Service Centre, specifying the nature of the problem, the

model of the equipment (Mod.), the product number (Prod. No.) and the serial

number(Ser. No.). These data are provided in the plate on the cover of this manual.

Always request the use of original spare parts.

Warranty conditions

You new appliance is covered by a warranty. The warranty conditions are provided in

full in the Warranty conditions-Service centers leaflet which you will find inside

the appliance

Keep the fiscal receipt or delivery note, either of which documents your purchase of

the appliance and provides proof of date of purchase, in a safe place together with the

leaflet.

If the After-Sales Service is call in, show these documents to the staff. If this

procedure is not followed, the Service-Centre will have no option but to charge for

any repairs.

If necessary, you may find your nearest Centre by consulting the Warranty

conditions Service centers.

7

Technical Data

MAX MIN G30 OUTPUT OUTPUT 28-30mbar

BURNER Nozzle

TYPE Kw Kw Cons

Making g/h

mm Small

Auxiliary 1.00 0.35 0.50 73 burner

Medium Semi-rapid 1.75 0.65 0.65 127

Burner Large rapid 2.0 1.0 0.70 146

burner Triple 0.43 flame 4.0 0.35 + 292 burner 0.93

Gas intake connection G1/2

Electricity supply 220-240v~50/60Hz

Instructions for the installation technician CAUTION: This appliance must only be installed and used in rooms with

permanent ventilation to local standards.

Installation of the appliance and its connection to the electrical mains must

only be carried out by QUALIFIED PERSONEL.

Before any procedure, it is important to check that the appliance is

DISCONNECTED from the electrical mains. The Manufacturer declines all

responsibility for any damage arising from installation in breach of the

regulations in force or from failure to comply with the accident prevention

regulations.

8

Installation premises

For proper operation of a gas appliance, the air necessary for the combustion of the

gas must be able to flow into the room naturally. The air must flow into the room

directly through openings in the outside walls. These openings must have an

unobstructed cross-section not less than 2m 3 /hfor each kw of power (see total power

in kw on the appliance nameplate).

This opening must be constructed so that it will not be

obstructed from inside or outside, or constructed close to

the floor. The opening is recommended to be on the side

opposite to that on which the flue gases are discharged. If it

is not feasible to provide these openings in the room where

the appliance is installed, the necessary air may be taken

from an adjacent room, provided that:

this room is not a bedroom or a hazardous environment;

this room has ventilation;

the ventilation between the room where the appliance is

installed and the adjacent room has openings.

Discharge of flue gases

Gas cooking appliances must discharge their flue gases

through hoods connected directly to flues or the outdoors.

If it is not possible to install the hood (fig. B) an electric

fan must be installed on the outside wall or the window of

the room, provided it is possible for the ventilation opening

to be increased in proportion to the delivery rate of the fan

(fig. C). For a kitchen, the delivery rate of this electric fan

must guarantee an hourly air exchange of 3-5 times its

volume. In both instances, the use of flues already used by other appliances to

discharge the flue gases is forbidden.

9

Connection to the gas supply

The gas Connection must be made in accordance with the

local standards. When installing, fit a safety tap at the end

of the pipeline. The appliance leaves the factory tested and

set for the type of gas indicated on the plate inside the

bottom guard, close to the gas connection pipe. Make sure

that the type of gas to be supplied to the appliance is the

same as that shown on the plate. Otherwise, follow the

instructions provided in the Adapting to different types of

gas section.

For maximum efficiency and minimum consumption, make

sure that the gas supply pressure complies with the values

shown in the gas used is different from that specified (or

variable).a suitable pressure regulator must be installed on

the supply pipeline.

The union must be fitted on the end of the gas train. Complete with GJ1/2threaded

nut, fitting the gasket between the components as shown in the illustration. The

gaskets must comply with the local standards. Screw the parts together without

forcing, fit the union so that it points in the direction required then tighten all parts.

Connection

Make the connection to the gas system using a rigid metal pipe and regulation unions,

or with a stainless steel hose complying with the local standard. If metal hoses are

used, take care that they do not come into contact with mobile parts and are not

crushed. This must also be checked if the hob is to be combined with an oven.

The gas intake connection of the appliance has a male thread.

When making the connection, take care not to apply stresses of any kind to the

appliance.

When the installation is complete, always check that all the unions are

absolutely tight using a soapy solution. Never use a flame to make this

check.

10

Electrical connection The appliance is profited to operate with a power

supply voltage of 230Vsingle-phase. The connection

must be made in accordance with the regulations and

laws in force.

Before making the connection, make sure that:

1) the safety circuit-breaker and the electrical

system are able to withstand the load of the

appliance(see nameplate).

2) The power supply system has an earth

connection in good working order in accordance

with the regulations in force;

3) The socket or omni polar switch use are easily

accessible with the appliance installed.

Fit a plug suitable for the load on the power lead and

connect it to a suitable safety socket.

If you wish to make a direct connection to the mains,

an omni polar switch with a gap between the contacts of at least 3 mm, of suitable

rating for the load and complying with the regulations in force, must be installed

between the appliance and the mains. The switch must not break a contact in the

yellow/green earth wire.

The brown live wire (connected to the L terminal of the terminal board) must

always be connected to the live wire of the power supply mains.

In all cases, the power supply lead must be positioned so that it does not reach a

temperature 50 o C above the room temperature at any point.

One example of an ideal route is shown in the illustration. The cable is guided by

means of band clamps fixed to the side of the cabinet, in order to avoid any contact

with the appliance underneath the hob.

Replacing the power supply lead

If the lead has to be replaced, only HO5RR-F or

HO5RN-F type cables suitable for the load and the

operating temperature must be used. In addition, the

yellow/green earth wire must be about 2 cm longer than

the live and neutral wires.

11

Adapting to the different types of gas

Changing the nozzles

1) Remove the pan standee.

2) Remove the burner caps and flame caps from the burners.

3) Use a size 7 socket wrench to unscrew and remove the

nozzles, replacing them with those corresponding to the

type of gas to be used (see the table ).

4) Reassemble the parts, reversing the operations described

above.

5) Then replace the setting data (close to the mains gas

connection)with the one for the new type of gas If the pressure of the gas used is

different from that specified(or variable),a suitable piped gas pressure regulator

complying with the standard must be installed on the supply pipeline.

Setting the minimum level

1) Light the burner as already described.

2) Turn the tap to the minimum flame position.

3) Remove the control knobs.

4) LPG TO NG:

Use a thin blade screwdriver to turn the by-pass screw

located above left of the gas valve, shaft as shown right. Turn

gently the by-pass screw clockwise to the end completely

then turn it anti-clockwise 1/2 turn for the Triple flame burner, 3/4 turn for the

Large rapid burner, 1/2 turn for the Medium Semi-rapid Burner

and 3/8 turn for the Auxiliary burner.

NG TO LPG:

Use a thin blade screwdriver to turn the by-pass screw located above left of the

gas valve shaft as shown right. Turn gently the by-pass screw clockwise to the

end.

5Finally, check that the burner does not go out when the tap is turned quickly from

the maximum to the minimum position.

12

Building into fitted kitchen units

These hobs are designed for installation in fitted kitchen units up to 600mm deep with

suitable characteristics.

Any cabinet side panels taller than the height of the hob itself must be at least 150mm

away from the opening into which the hob is inserted.

The dimensions of the hob and the installation opening are shown in the illustration.

Insertion and fixing

Before inserting the hob in the installation

opening, place the special gasket around the

bottom edge of the hob.

It is important to fix this gasket evenly,

without gaps or overlapping, to prevent liquid

from seeping underneath the hob.

1) Remove the pan stands and the burner

caps and turn the hob upside down, taking

care not to damage the ignition plugs and

the thermocouples.

2) Place the gasket around the bottom edge

of the hob as shown in the illustration on

the right.

3) Place the hob in the installation opening

and push it down so that the hob

Manualsnet FAQs

If you want to find out how the 5GH75BB490 Blaupunkt works, you can view and download the Blaupunkt 5GH75BB490 Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Blaupunkt 5GH75BB490 as well as other Blaupunkt manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Blaupunkt 5GH75BB490. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Blaupunkt 5GH75BB490 Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Blaupunkt 5GH75BB490 Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Blaupunkt 5GH75BB490 Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Blaupunkt 5GH75BB490 Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Blaupunkt 5GH75BB490 Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.