Black & Decker PI400LA-B3 Inverter Instruction Manual PDF

1 of 17
1 of 17

Summary of Content for Black & Decker PI400LA-B3 Inverter Instruction Manual PDF

Conversor Elctrico Power Inverter

MANUAL DE INSTRUCCIONES INSTRUCTION MANUAL

Cat. N PI400LA

ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. WARNING: READ INSTRUCTION MANUAL BEFORE USING PRODUCT.

Espaol 3 English 11

FIG. A

1

2

3

4 5

6

7 8

9 10

11

ESPAOL 3 NO DEVUELVA ESTE PRODUCTO A LA TIENDA,

comunquese antes a las oficinas locales o con el Centro de Servicio Black & Decker ms cercano a usted.

CONSERVE ESTAS INSTRUCCIONES

Advertencia! Lea todas las instrucciones antes de operar el producto. El incumplimiento de todas y cada una de las instrucciones enumeradas a continuacin puede provocar una descarga elctrica, un incendio o lesiones graves.

NORMAS GENERALES DE SEGURIDAD INSTRUCCIONES DE SEGURIDAD Advertencias de seguridad generales para herramientas elctricas.

Atencin! Lea todas las advertencias e instrucciones de seguridad. En caso de no respetarse las advertencias e instrucciones indicadas a continuacin, podra producirse una descarga elctrica, incendio y/o lesin grave.

Conserve todas las advertencias e instrucciones para su posterior consulta. El trmino empleado en las advertencias indicadas a continuacin se refiere a la herramienta elctrica con alimentacin de red (con cable) o alimentada por pila (sin cable).

f Evite las condiciones ambientales peligrosas. No utilice artefactos en zonas hmedas o mojadas. No utilice artefactos bajo la lluvia.

f Mantenga a los nios alejados. Los visitantes deben mantenerse a distancia del rea de trabajo.

f Guarde los artefactos que no utilice en el interior. Cuando no los utilice, los artefactos deben guardarse en el interior en un lugar seco, alto o bajo llave, lejos del alcance de los nios.

f No fuerce el aparato. Trabajar mejor y con menos probabilidad de riesgo de daos si se opera a la velocidad para la que fue diseado.

f Utilice el aparato adecuado. Nunca utilice el aparato para otra tarea que no sea aquella para la que fue creada.

f Use la vestimenta adecuada. No use ropas holgadas o joyas. Pueden atascarse en las piezas en movimiento. Se recomienda utilizar guantes de goma y calzado antideslizante considerable al trabajar al aire libre. Recjase y cubra el cabello largo.

f Use anteojos de seguridad y cualquier otro equipo de seguridad. Use anteojos protectores o lentes de seguridad con proteccin lateral que cumplan con las normas de seguridad aplicables y, de ser necesario, un protector facial. Utilice tambin mscaras faciales o para polvo si la operacin produce polvillo. Esto se aplica a todas las personas que se encuentren en el rea de trabajo. Utilice tambin un casco, proteccin auditiva, guantes,

calzado de seguridad y sistemas de recoleccin de polvo cuando as se especifique o requiera.

f No tire del cable. Nunca transporte el aparato por el cable ni lo jale para desconectarlo del tomacorriente. Mantenga el cable alejado del calor, el aceite y los bordes afilados.

f No se estire. Conserve el equilibrio y prese adecuadamente en todo momento.

f Desconecte los aparatos. Desconecte el aparato de la fuente de energa cuando no lo utiliza, antes de realizar un mantenimiento y al cambiar accesorios como hojas y elementos semejantes.

f Evite el encendido por accidente. No transporte el aparato enchufado con el dedo en el interruptor. Asegrese de que el interruptor est apagado cuando lo enchufe.

f El enfriamiento correcto es fundamental al operar el conversor. No coloque la unidad cerca de los orificios de ventilacin del vehculo ni la exponga a la luz solar directa.

f La proteccin del interruptor del circuito de la avera elctrica se debe proporcionar en los circuitos o los enchufes que se utilizarn. Los receptculos estn disponibles que construyen en la proteccin del interruptor del circuito de la avera elctrica y se pueden utilizar para esta medida de seguridad.

f Uso de suplementos y accesorios. El uso de accesorios o dispositivos no recomendados para este aparato puede resultar peligroso. Nota: Consulte la seccin Accesorios de este manual para obtener detalles adicionales.

f Mantngase alerta. Fjese en lo que est haciendo. Use el sentido comn. No opere la herramienta si est cansado.

f Verifique que no haya piezas daadas. Antes de volver a utilizar la herramienta, se debe controlar cualquier proteccin u otra pieza que est averiada para determinar si funcionar correctamente y realizar la funcin para la que fue diseada. Verifique la alineacin y la sujecin de las piezas mviles, la rotura de piezas, el montaje y cualquier otra condicin que pueda afectar su operacin. Cualquier proteccin u otra pieza que est daada debe ser reparada correctamente o reemplazada por un centro de mantenimiento autorizado, a menos que este manual de instrucciones indique otra cosa. Reemplace los interruptores defectuosos en un centro de mantenimiento autorizado. No utilice la herramienta si no puede encenderla o apagarla con el interruptor.

f No opere herramientas elctricas porttiles cerca de lquidos inflamables o en atmsferas gaseosas o explosivas. Los motores de estas herramientas normalmente chispean, y las chispas pueden encender los vapores.

4 ESPAOL f En espacios abiertos, use cables prolongadores.

Cuando utiliza la herramienta al aire libre, utilice solamente cables prolongadores diseados para su uso al aire libre o marcados como tales.

f Cables prolongadores. Asegrese de que el cable prolongador est en buenas condiciones. Cuando utilice un cable prolongador, cercirese de que tenga la capacidad para conducir la corriente que su producto exige. Un cable de menor capacidad provocar una disminucin en el voltaje de la lnea, lo cual producir una prdida de potencia y sobrecalentamiento.

NORMAS DE SEGURIDAD: DEFINICIONES Peligro! Indica una situacin de peligro inminente que,

si no se evita, provocar la muerte o lesiones graves. Advertencia! Indica una situacin de peligro potencial

que, si no se evita, podra provocar la muerte o lesiones graves. Precaucin! Indica una situacin de peligro potencial

que, si no se evita, provocar lesiones leves o moderadas. Precaucin! Cuando se utiliza sin el smbolo de alerta

de seguridad indica una situacin de peligro potencial que, si no se evita, puede provocar daos a la propiedad.

Riesgo de operacin insegura. Cuando se utilizan herramientas o equipos, siempre se deben respetar las precauciones de seguridad para reducir el riesgo de lesiones personales. La operacin, el mantenimiento o la modificacin incorrectos de herramientas o equipos pueden provocar lesiones graves y daos a la propiedad. Las herramientas y los equipos estn diseados para determinados usos. Black & Decker recomienda enfticamente que NO se modifique este producto y que NO se utilice para ningn otro uso que aqul para el que fue diseado. Lea y comprenda todas las instrucciones operativas y las advertencias antes de utilizar cualquier herramienta o equipo.

Advertencia! Mantngase lejos del AGUA, FUEGO, HUMO!

Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual de instrucciones. Este manual contiene informacin importante con relacin a la operacin y garanta de este producto. Por favor consrvelo para referencia futura.

El conversor tiene funciones de proteccin como apagado de sobrevoltaje de entrada, apagado de voltaje bajo de entrada, reanudacin de apagado de bajo voltaje, auto seguro de sobre calentamiento, auto seguro de sobrecarga y proteccin de corto circuito, el indicador LED desplegar directamente la entrada de energa y los errores. La unidad no est diseada para que sea a prueba de agua.

INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD

Advertencia! Para reducir el riesgo de descarga elctrica:

f No conecte al cableado de distribucin de CA. f No realice conexiones o desconexiones elctricas

en reas designadas como protegidas contra ignicin. Esto incluye el adaptador para aviones o el enchufe tipo encendedor de cigarrillos de CC. Esta unidad No est aprobada para reas protegidas contra ignicin.

f Nunca sumerja la unidad en el agua ni en ningn otro lquido, ni la utilice cuando est hmeda.

f No introduzca objetos extraos en el tomacorriente de CA ni en el puerto USB.

Advertencia! Para reducir el riesgo de incendio: f No opere cerca de materiales, vapores o gases

inflamables. f El enfriamiento correcto es fundamental al operar

el conversor. No coloque la unidad cerca de los orificios de ventilacin del vehculo ni la exponga a la luz solar directa.

f No lo exponga al calor extremo o a las llamas.

Precaucin! Para reducir el riesgo de lesiones o dao a la propiedad:

f No opere cerca de materiales, vapores o gases inflamables.

f El enfriamiento correcto es fundamental al operar el conversor. No coloque la unidad cerca de los orificios de ventilacin del vehculo ni la exponga a la luz solar directa.

f No lo exponga al calor extremo o a las llamas.

Precaucin! Para reducir el riesgo de lesiones o dao a la propiedad:

f Desenchufe el aparato de la tira del tomacorriente o apague el conversor antes de trabajar en el aparato. Varias cintas de la potencia de salida con interruptores e interruptores automticos slo interrumpen la potencia en los terminales del tomacorriente caliente. Los terminales neutros siguen alimentndose en relacin con los terminales a tierra.

f No intente conectar o configurar la unidad o sus componentes mientras maneja su vehculo. El hecho de no prestar atencin a la carretera puede tener como consecuencia un accidente grave.

f Siempre utilice el conversor en lugares adecuadamente ventilados. No bloquee las ranuras de ventilacin.

f Siempre apague el conversor desenchufndolo del tomacorriente para accesorios de CC cuando no lo utilice.

f Asegrese de que el voltaje nominal de encendido sea CC de 12V, conexin central POSITIVO (+).

ESPAOL 5 f Al utilizar esta unidad en un vehculo, revise el manual

del usuario del vehculo para ver el mximo rango de potencia y la salida recomendada. Tal vez sea necesario cambiar el fusible en lnea del tomacorriente del vehculo a un rango mayor. No lo instale en el compartimiento del motor. Instlelo en un rea bien ventilada.

f No lo utilice con sistemas elctricos con positivo a tierra*. La conexin de polaridad inversa har que un fusible se queme y puede causar un dao permanente al conversor y anular la garanta. * La mayora de los automviles, vehculos recreativos y camiones modernos posee un negativo a tierra.

f Tenga en cuenta que este conversor no funcionar con aparatos o equipos de alta potencia en Watts que produzcan calor, como secadores de cabello, hornos de microondas y tostadores.

f No abra el conversor: no hay piezas que el usuario pueda reparar en su interior.

f No utilice este conversor con dispositivos mdicos. No se ha comprobado su funcionamiento en aplicaciones mdicas.

f Mantenga fuera del alcance de los nios. Esto no es un juguete!

f Instale y opere la unidad solamente como se describe en este manual de instrucciones.

f No utilice este conversor en un bote. No se califica para los usos marinos.

f Controle el desgaste de la unidad peridicamente. Lleve la unidad a un tcnico calificado para reemplazar las piezas desgastadas o defectuosas de inmediato.

f No conecte la unidad a cualesquier sistemas de distribucin de energa de una empresa de servicios pblicos o circuitos de derivacin.

f No utilice el conversor en temperaturas superiores a 104 F (40 C) o inferiores a 32 F (0 C).

f El no seguir estos lineamientos de seguridad resultar en lesiones personales y/o daos a la unidad. Tambin puede anular la garanta.

f Lea y entienda este manual de instruccin antes de usar esta unidad.

CONSERVE ESTAS INSTRUCCIONES Este manual contiene instrucciones importantes de seguridad y de operacin para el conversor de 400W con puerto de carga USB (PI400LA).

Advertencia! Para reducir el riesgo de lesiones: f Siga estas instrucciones y las publicadas por el

fabricante de la batera y de cualquier equipo que tenga la intencin de utilizar con esta unidad. Revise las indicaciones sobre precauciones en estos productos y en el motor.

INTRODUCCIN Gracias por comprar el Sistema de Energa del Vehculo Conversor Elctrico de 400W con Puerto de Carga USB (PI400LA). Este conversor puede utilizarse para operar productos electrnicos personales, como: Computadoras porttiles, cmaras digitales o filmadoras, reproductores de MP3, telfonos celulares, agendas electrnicas y ms. Tambin puede utilizarse para recargar dispositivos de CA que tengan un adaptador de recarga apropiado con un enchufe de dos o tres patas estadounidense estndar. Lea este manual de instrucciones detenidamente antes de utilizar la unidad para garantizar su ptimo rendimiento y evitar daar el producto.

CARACTERSTICAS El panel frontal presenta dos indicadores LED. El indicador LED verde indica la potencia y la operacin adecuada del conversor. Los enchufes de la CA y del USB son listos utilizar. El indicador LED rojo indica que el conversor se apag debido a una sobrecarga o condicin de temperatura excesiva.

El botn de la energa da vuelta al conversor por intervalos. Puede tambin ser utilizado para forzar el reajuste de los circuitos del conversor presionndolo APAGADO (no se enciende ningunos LED), entonces detrs ENCENDIDO otra vez.

El PI400LA posee dos tomacorrientes. El tomacorriente pueden adaptarse a enchufes de CA de dos o tres patas. La potencia tambin puede suministrarse a travs del tomacorriente de CC de 12V.

Controles y funciones (Fig. A) 1. Conversor elctrico 2. Clips para la batera (con los cables) 3. Enchufe para adaptador de vehculo de 12V de CC 4. Indicador LED de falla en la salida de corriente 5. Indicador LED de falla en la entrada de corriente 6. Botn de Conectado/Desconectado de la energa 7. Tomacorriente de tres patas de CA con cubierta 8. Puerto de carga USB 9. Ventilador de enfriamiento de alta velocidad 10. Conexin elctrica de CC del positivo (+) (Rojo) 11. Conexin elctrica de CC del negativo () (Negro)

Funcionamiento del conversor El conversor es un dispositivo electrnico que convierte electricidad de CC (corriente continua) de bajo voltaje de una batera a energa para uso domstico de CA (corriente alterna). Durante el diseo de este conversor, Black & Decker incorpor tcnicas de diseo utilizadas anteriormente en fuentes de energa para computadoras. El resultado de estas innovaciones en el diseo es un conversor elctrico ms pequeo, ms liviano y ms fcil de utilizar.

6 ESPAOL El conversor de 400W convierte la energa en dos etapas:

f La primera etapa consiste en un proceso de conversin de CC a CC que incrementa la CC de bajo voltaje en la entrada del conversor a CC de 145V.

f La segunda etapa es una etapa puente MOSFET (transistor de efecto de campo semiconductor de xido metlico) que convierte la CC de alto voltaje a 220V, 50-60HZ AC.

La forma de onda de salida del conversor elctrico La forma de onda de la salida de CA de este conversor se conoce como una onda senoidal modificada. Es una forma de onda escalonada que posee caractersticas similares a la forma de onda senoidal de la electricidad. Este tipo de forma de onda es adecuado para la mayora de las cargas de CA, incluidas las fuentes de energa por conmutacin y lineales utilizadas en equipos electrnicos, transformadores y motores pequeos.

La onda senoidal modificada producida por este conversor posee un voltaje RMS (raz cuadrada media) de 220V. La mayora de los voltmetros de CA (digitales y anlogos) son sensibles al valor promedio de la forma de onda en lugar de al valor RMS. Estn calibrados para el voltaje RMS suponiendo que la forma de onda medida ser una onda senoidal pura. Estos medidores no leern correctamente el voltaje RMS de una onda senoidal modificada. Un medidor RMS no VERDADERO leer aproximadamente 20V a 30V mnimo cuando mida la salida de este conversor. Para realizar una medicin adecuada del voltaje de salida de esta unidad, utilice un voltmetro de lectura RMS VERDADERO como un Fluke 87, Fluke 8060A, Beckman 4410 o Triplett 4200.

CA modificada de la onda

220V del seno

CA de la onda 220V del seno

Modified sine wave 220V AC

Sine wave 220V AC

Fig. 1: Salida de CA Precaucin! Dispositivos recargables f Algunos dispositivos recargables estn diseados

para cargarse al ser enchufados directame te en un tomacorriente de CA. Estos dispositivos pueden daar el con rsor o el circuito que se est cargando.

f Si hay algn indicio de que su artefacto se comporta de forma distinta a cuando est conectado a la fuente de energa normal, entonces desenchfelo y busque el asesoramiento del fabricante de su aparato.

f Al utilizar un dispositivo recargable, supervise la temperatura durante los primeros 10 minutos de uso para determinar si genera calor en exceso.

f Si produce calor en exceso, esto indica que el dispositivo no debe utilizarse con este conversor.

f Este problema no se presenta con la mayora de los equipos operados con batera. La mayora de estos dispositivos utiliza un cargador o transformador por separado que est enchufado en un tomacorriente de CA.

f El conversor puede funcionar con la mayora de los cargadores y transformadores.

MAXX SST Tecnologa suave del comienzo

La tecnologa suave del comienzo de Black & Decker gradualmente rampas para arriba la energa de los conversores de comenzar lentamente las aplicaciones que requieren una oleada conseguir comenzada. Esta rampa gradual para arriba protege el conversor y la aplicacin, as como la fuente de energa, contra dao y falta.

INSTRUCCIONES DE OPERACIN El Conversor elctrico debe estar conectado solamente a bateras con un voltaje de salida nominal de 12V. La unidad no funcionar si se coloca una batera de 6V y ocasionar un dao permanente si se conecta a una batera de 24V.

Siempre conecte el el PI400LA a la fuente de energa de CC de 12V antes de conectar cualquier dispositivo al conversor.

Los tomacorrientes de CA y los puertos USB permiten al usuario operar varios dispositivos simultneamente. Simplemente enchufe el equipo en la unidad y opere normalmente. Asegrese de que la potencia en Watts de todos los equipos enchufados simultneamente en el PI400LA no supere los 400W continuos.

Conexin a la fuente de energa El conversor elctrico viene equipado con cables para pinzas para la batera para su conexin a una fuente de energa.

Conexin a una fuente de energa utilizando el enchufe de salida para accesorios El enchufe de salida para accesorios de CC es adecuado para operar el conversor con salidas de energa de hasta 100 Watts. La punta del enchufe es el POSITIVO (+) y el contacto lateral es el NEGATIVO ().

Conecte el conversor a la fuente de energa insertando el enchufe de salida para accesorios de CC con firmeza dentro del tomacorriente para accesorios de un vehculo o de otra fuente de energa.

ESPAOL 7 PRECAUCIONES

f Conecte directamente a una fuente de energa al operar a ms de 100W.

f No utilice con sistemas elctricos con positivo a tierra. f La conexin de polaridad inversa har que un fusible se

queme y puede causar un dao permanente al conversor. Notas: La mayora de los circuitos de salida para accesorios del vehculo poseen fusibles clasificados en 15A a 20A o ms. Para operar a la potencia en Watts mxima, utilice el cable de la pinza de la batera (suministrado) o conecte directamente a la fuente de energa con el cable y el fusible suministrado por el usuario. La mayora de los automviles modernos, vehculos recreativos y camiones posee un negativo a tierra. Una vez conectado adecuadamente a una fuente de energa de CC de 12V y encendido, el indicador LED de potencia enciende una luz verde que indica que el conversor est funcionando correctamente. Si el indicador LED de fallas de entrada enciende una luz amarilla o el indicador LED de fallas de salida enciende una luz roja, esto indica que existe una falla. Consulte la seccin Deteccin de problemas de este Manual de instrucciones.

Conexin a una fuente de energa utilizando los clips de la batera Utilice los clips de la batera con cables y conecte el conversor elctrico directamente a la fuente de energa de 12V de la siguiente manera: 1. Compruebe para cerciorarse de que se haya extrado el botn de la energa del conversor (no se enciende ningunos LED) y de que no haya vapores inflamables en el rea de instalacin. 2. Conecte el cable ROJO al borne ROJO marcado como (+) en la parte posterior del conversor. Conecte la pinza de la batera al terminal POSITIVO de la batera. 3. Conecte el cable NEGRO al borne NEGRO marcado como () en la parte posterior del conversor. Conecte la pinza de la batera al terminal NEGATIVO de la batera. 4. Asegrese de que todas las conexiones entre las pinzas de la batera y los terminales sean firmes.

Cableado directo a la fuente de energa (mtodo opcional de la conexin; hardware no incluido)

Advertencia! Para evitar que el conversor funcione en forma defectuosa, se recomienda no instalarlo con cables de una extensin superior a 3m (10 pies).

Utilice el alambre del AWG #6 si el conversor a la conexin de la fuente de energa es 6 pies o menos. Para longitudes de cable ms largas utilice el alambre del AWG #4. En cualquier caso, proteja (+) el alambre positivo contra cortocircuitos instalando un fusible o el interruptor de 35 ANL cerca del terminal de la fuente de la potencia CC (batera).

1. Compruebe para cerciorarse de que se haya extrado el botn de la energa del conversor (no se enciende ningunos LED) y de que no haya vapores inflamables en el rea de instalacin. 2. Identifique los terminales POSITIVO (+) y NEGATIVO () (batera) de la fuente de energa de CD. 3. Instale un soporte para fusibles o interruptor cerca del terminal POSITIVO (+) de la fuente de energa (batera) de CD. 4. Conecte una prolongacin de cable en un lado del soporte del fusible o del interruptor automtico. Conecte el otro extremo del cable al terminal POSITIVO (+) del conversor. 5. Conecte una prolongacin del cable entre el terminal NEGATIVO () del conversor y el terminal NEGATIVO () de la fuente de energa de CD. 6. Conecte una prolongacin corta del cable al otro terminal del soporte del fusible o al interruptor automtico. Mrquelo como POSITIVO o +. 7. Conecte el extremo libre del fusible o del cable del interruptor al terminal POSITIVO (+) de la fuente de energa (batera) de CD. 8. Inserte un fusible adecuado al conversor en el soporte del fusible. 9. Pruebe el conversor encendindolo y enchufndolo en una lmpara o equipo de 100W. 10. Si el conversor no funciona correctamente, consulte la seccin Deteccin de problemas de este manual.

PRECAUCIONES GENERALES f Los conectores sueltos pueden hacer que los cables

se sobrecalienten y que el aislamiento se derrita. f Compruebe para asegurarse de que no ha invertido

la polaridad. Los daos ocasionados por polaridad inversa no estn cubiertos por nuestra garanta.

Conexin a la carga El conversor elctrico viene con tomacorrientes estndar dobles de potencia de CA. Enchufe el cable al equipo que desee operar en el tomacorriente de CA. Asegrese de que el requisito de carga combinada no exceda la potencia continua mxima.

El conversor elctrico est diseado para conectarse directamente a equipos elctricos y electrnicos estndar de la forma en que se describi anteriormente. No conecte el conversor elctrico a cableados de distribucin de CA de vehculos recreativos o para uso domstico. No conecte el conversor elctrico a cualquier circuito de carga de CA en el que el conductor neutro est conectado a tierra o al NEGATIVO de la fuente (batera) de energa de CC.

Advertencia! No conecte al cableado de distribucin de CA.

8 ESPAOL Consumo de corriente real versus calificado del equipo La mayora de las herramientas elctricas, los aparatos y los equipos de audio/vdeo posee etiquetas que indican el consumo de potencia en Amperes o Watts. Asegrese de que el consumo de potencia del artculo que desee operar posea la misma calificacin o una menor a la calificacin de salida del conversor. Si el consumo de energa se clasifica en CA de Amperes, simplemente multiplique por los Volts de CA para determinar la potencia en Watts (220).

El conversor elctrico puede transportar las cargas resistivas con ms facilidad. No obstante, las cargas resistivas ms grandes, como estufas o calentadores elctricos, generalmente requieren ms potencia en Watts de la que puede suministrar el conversor elctrico en forma continua. Las cargas inductivas, como televisores y estreos, requieren ms corriente para funcionar que las cargas resistivas de la misma clasificacin de potencia en Watts.

La unidad se apagar si se sobrecarga. Para recomenzar la unidad, desenchufe simplemente todos los dispositivos tapados en la unidad; desconecte la unidad de cualquier fuente de la potencia CC de 12V; entonces vuelva a conectar la unidad ANTES de tapar la aplicacin detrs adentro.

Funcionamiento del tomacorriente de CA 1. Conecte el conversor con una fuente de funcionamiento de la potencia CC de 12V segn lo descrito en este manual de instruccionne. Si usa el adaptador accesorio del vehculo de la CC de 12V, rote el enchufe accesorio del vehculo levemente para cerciorarse de que hay buen contacto. Cercirese de que haya espacio adecuado para la ventilacin apropiada del conversor. 2. Presione el botn de la energa para girar la unidad. 3. El indicador verde de la energa LED se encender, indicando una conexin apropiada. Si existe el indicador amarillo de la avera LED de la entrada o las luces de indicador rojas de la avera LED de la salida, indicando una condicin de avera, refiera a la seccin de localizacin de averas de este manual de instruccionne. 4. Si el conversor no funciona, asegrese de que el interruptor de accesorios/ignicin est suministrando realmente energa al tomacorriente para accesorios. Algunos vehculos exigen que el interruptor de ignicin est en la posicin de encendido. 5. Enchufe el aparato (CA de 220V) en uno de los tomacorrientes de CA de tres patas del conversor y opere normalmente. Nota: El conversor no servir para aparatos y equipos que generen calor, como secadores de cabello, mantas trmicas, hornos de microondas y tostadores. Recuerde desconectar la unidad de cualquier fuente de energa cuando no es adentro uso.

Funcionamiento del puerto de carga USB 1. Conecte el conversor con una fuente de funcionamiento de la potencia CC de 12V segn lo descrito en este manual de instruccionne. Si usa el adaptador accesorio del vehculo de la CC de 12V, rote el enchufe accesorio del vehculo levemente para cerciorarse de que hay buen contacto. Cercirese de que haya espacio adecuado para la ventilacin apropiada del conversor. 2. Presione el botn de la energa para girar la unidad. 3. El indicador verde de la energa LED se encender, indicando una conexin apropiada. Si existe el indicador amarillo de la avera LED de la entrada o las luces de indicador rojas de la avera LED de la salida, indicando una condicin de avera, refiera a la seccin de localizacin de averas de este manual de instruccionne. 4. Si el conversor no funciona, asegrese de que el interruptor de accesorios/ignicin est suministrando realmente energa al tomacorriente para accesorios. Algunos vehculos exigen que el interruptor de ignicin est en la posicin de encendido. 5. Enchufe el dispositivo elctrico USB en el puerto de carga USB del conversor y opere normalmente.

Nota: Algunos telfonos mviles vienen provistos de un cable de datos en lugar de un cable de carga. Esto puede provocar que su telfono mvil no se cargue a travs del puerto USB. Consltelo con el fabricante del telfono mvil.

Nota: El Puerto de carga USB del conversor no admite comunicacin de datos. Slo proporciona energa de CC de 5V/500 mA a un dispositivo elctrico USB externo. Recuerde desconectar la unidad de cualquier fuente de energa cuando no es adentro uso.

CARACTERSTICAS DE PROTECCIN El conversor supervisa las siguientes condiciones: a. Voltaje bajo de la batera: este estado no es perjudicial para el conversor, pero puede daar la fuente de energa, de modo que el conversor se apagar automticamente cuando el voltaje de entrada disminuya a una CD de 10,5V 0,3V. Al corregir esta condicin, la unidad se reiniciar automticamente. b. Proteccin contra voltaje en exceso: el conversor se apagar automticamente cuando el voltaje de entrada sea mayor a una CD de 15,5V 0,5V. c. Proteccin de apagado trmico: El conversor se apagar automticamente cuando la unidad se sobrecaliente. d. Proteccin contra cortocircuitos: el conversor se apagar automticamente en presencia de un cortocircuito. El conversor se reiniciar automticamente despus de quitar el cortocircuito.

ESPAOL 9 SUGERENCIAS DE OPERACIN El conversor slo debe operarse en lugares: a. Secos: No permita que el agua u otros lquidos entren en contacto con el conversor. b. Frescos: La temperatura ambiente debe estar entre 10C y 20C (50F y 68F). Mantenga el conversor lejos de la luz solar directa siempre que sea posible. c. Bien ventilados: Mantenga el rea que rodea el conversor limpia para garantizar la libre circulacin de aire alrededor de la unidad. No coloque artculos en o sobre el conversor durante su funcionamiento. La unidad se apagar si la temperatura interna se eleva demasiado. El conversor se reiniciar automticamente despus de enfriarse. d. Seguros: No utilice el conversor cerca de materiales inflamables o en lugares donde se puedan acumular vapores o gases inflamables. ste es un aparato elctrico que puede generar chispas durante breves perodos si se establecen conexiones elctricas o stas se rompen.

CUIDADO Y MANTENIMIENTO Almacenamiento 1. La temperatura ideal de almacenamiento vara entre 0C y 40C (32F y 104F). 2. Almacene y use el conversor en un lugar fresco y seco y con ventilacin adecuada en los alrededores. 3. Evite los lugares expuestos a unidades de calefaccin, radiadores, luz solar directa o humedad en exceso.

Reemplazo del fusible Este conversor viene con varios fusibles internos. Normalmente, estos fusibles no se quemarn a menos que exista un problema grave dentro de la unidad. Los fusibles internos pueden reemplazarse, no obstante, slo debe hacerlo el personal capacitado para reemplazar fusibles. Si la unidad se daa durante el reemplazo del fusible, la garanta puede quedar anulada.

El fusible en el enchufe accesorio del enchufe de la CC es usuario-reemplazable. Cercirese de a primero desconectan el enchufe del enchufe de cualquier fuente de la potencia CC de 12V; entonces substituya el fusible por uno del mismo grado y tipo.

PROTECCIN DEL MEDIO AMBIENTE Separacin de desechos. Este producto no debe desecharse con la basura domstica normal. Si llega el momento de reemplazar su producto Black & Decker o ste ha dejado de tener utilidad para usted, no lo deseche con la basura domstica normal. Asegrese de que este producto se deseche por separado.

La separacin de desechos de productos usados y embalajes permite que los materiales puedan reciclarse y reutilizarse. La reutilizacin de materiales reciclados ayuda a evitar la contaminacin medioambiental y reduce la demanda de materias primas. La normativa local puede ofrecer la separacin de desechos de productos elctricos de uso domstico en centros municipales de recogida de desechos o a ravs del distribuidor cuando adquiere un nuevo producto.

ACCESORIOS El adecuado funcionamiento de la herramienta depende de los accesorios que utilice. Los accesorios Piranha y Black & Decker se han fabricado siguiendo estndares de alta calidad y se han diseado para mejorar el funcionamiento de la herramienta. Al utilizar estos accesorios, conseguir el mximo rendimiento de la herramienta.

INFORMACIN DE SERVICIO Todos los Centros de Servicio de Black & Decker cuentan con personal altamente capacitado dispuesto a brindar a todos los clientes un servicio eficiente y confiable en la reparacin de herramientas elctricas. Para mayor informacion acerca de nuestros centros de servicio autorizados y si necesita consejo tcnico, reparaciones o piezas de repuesto originales de fbrica, comuniquese a su oficina local o visitenos en www.BlackandDecker-la.com

ESPECIFICACIONES PI400LA Energa continua mxima: 400 Watts Capacidad de sobretensin: 800 Watts Puerto USB: 5V CC (500mA) Voltaje de entrada: 12,8V Alarma por voltaje bajo: CC de 11V 0,3V Parada por voltaje bajo: CC de 10,5V 0,3V Apagado trmico: Automtico Forma de onda: Onda senoidal modificada (MSW, por su sigla en ingls) Fusibles: Internos / Enchufe del accesorio de la CC de 12V: 10A Cables de entrada: Cables del clip de la batera /cable del adaptador de la CC 12V Temperatura de operacin: 10C y 20C (50F y 68F) Temperatura de almacenamiento: 0C a 40C (32F a 104F) Humedad relativa de operacin: 5% a 95% no condensada

10 ESPAOL DETECCIN DE PROBLEMAS

Problemas visuales/de audio frecuentes Problema Explicacin / recomendacin Zumbidos en los sistemas de audio

Algunos sistemas estreos y estreos econmicos generan zumbidos cuando se los pone en funcionamiento desde el conversor ya que la fuente de energa en el dispositivo electrnico no filtra correctamente la onda senoidal modificada producida por el conversor. La nica solucin a este problema es utilizar un sistema de sonido que posea una fuente de energa de calidad superior.

Interferencia con el televisor El Conversor est protegido a fin de reducir al mnimo la interferencia con las seales de televisin. Sin embargo, en determinadas situaciones, es posible que an haya alguna interferencia, particularmente con seales de televisin dbiles. Intente las siguientes medidas correctivas: 1. Mueva el conversor lo ms lejos posible del televisor, la antena y los cables de la antena. En caso de ser necesario, utilice un cable prolongador de CA corto. 2. Ajuste la orientacin de los cables de la antena y el cable de alimentacin del televisor para reducir al mnimo la interferencia. 3. Asegrese de que la antena conectada al televisor proporcione una seal adecuada (sin nieve) y que se utilice un cable de antena blindado de alta calidad.

Problemas frecuentes de potencia de salida Causas posibles Recomendacines El voltaje de la batera est por debajo de 10,5V Recargue la batera o verifique la fuente de energa de CC.

El equipo que se opera genera mucha energa

f Reduzca la carga a un mximo de 400W. f Conecte directamente con la fuente de energa usando los clips de batera

incluidos al funcionar sobre 100W. El conversor est en la condicin de apagado trmico

Espere que el conversor se enfre. Asegrese de que haya una ventilacin adecuada alrededor de la unidad y que la carga no sea mayor a 400W para un funcionamiento continuo.

La salida de CA est en cortocircuito

Desenchufe la aplicacin de la CA. Desconecte la unidad de cualquier fuente de la potencia CC de 12V. Compruebe la cuerda de la aplicacin. Refiera a la seccin de la informacin de servicio que sigue para entrar en contacto con un centro de servicio de Black & Decker.

ENGLISH 11 DO NOT RETURN THIS PRODUCT TO THE STORE,

first contact your local Black & Decker office or nearest authorized service center.

GENERAL SAFETY RULES Warning! Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS SAFETY INSTRUCTIONS General power tool safety warnings. Warning! Read all safety warnings and

all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference. The term power tool in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.

f Avoid dangerous environments. Dont use appliances in damp or wet locations. Dont use appliances in the rain.

f Keep children away. All visitors should be kept at a distance from work area.

f Store idle appliances indoors. When not in use, appliances should be stored indoors in dry, and high or locked-up place out of reach of children.

f Dont force appliance. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

f Use right appliance. Do not use the appliance for any job except that for which it is intended.

f Dress properly. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial, non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

f Use safety glasses and other safety equipment. Use safety goggles or safety glasses with side shields, complying with applicable safety standards and, when needed, a face shield. Also use face or dust mask if operation is dusty. This applies to all persons in the work area. Also use a hard hat, hearing protection, gloves, safety shoes and dust collection systems when specified or required. Safety glasses or the like are available at extra cost at your local dealer or Black & Decker Service Center.

f Dont abuse cord. Never carry appliance by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.

f Dont overreach. Keep proper footing and balance at all times.

f Disconnect appliances. Disconnect the appliance from the power supply when not in use, before servicing, and when changing accessories such as blades and the like.

f Avoid unintentional starting. Dont carry plugged-in appliance with finger on switch. Be sure switch is off when plugging in.

f Proper cooling is essential when operating the inverter. Do not place the unit near the vehicles heat vent or in direct sunlight.

f Electrical fault circuit interruptor protection should be provided on the circuits or outlets to be used. Receptacles are available having built in electrical fault circuit interruptor protection and may be used for this measure of safety.

f Use of accessories and attachments. The use of any accessory or attachment not recommended for use with this appliance could be hazardous. Note: Refer to the accessory section of this manual for further details.

f Stay alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired.

f Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off.

f Do not operate portable electric tools near flammable liquids or in gaseous or explosive atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes.

f Outdoor use extension cords. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

f Extension cords. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

SAFETY GUIDELINES: DEFINITIONS Danger! Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury. Warning! Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

12 ENGLISH Caution! Indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate injury. Caution! Used without the safety alert symbol indicates

potentially hazardous situation which, if not avoided, may result in property damage.

Risk of unsafe operation. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. Black & Decker strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating instructions before using any tool or equipment.

Warning! Keep away from WATER, FIRE, SMOKE! To reduce the risk of injury, user must read and understand this instructional manual. This manual contains important information regarding the operation and warranty of this product. Please retain for future reference.

The inverter has the protection functions such as over input voltage shut off, low input voltage shut off, Under- voltage turn-off resume, over heating self-lock, overload self-lock, short circuit protection, the LED indicator will directly display input power and errors.

IMPORTANT SAFETY INSTRUCTIONS Warning! To reduce the risk of electric shock: f Do not connect to AC distribution wiring. f Do not make any electrical connections or disconnections

in areas designated as ignition protected. This includes DC cigarette lighter type plug connection. This unit is Not approved for ignition protected areas.

f Never immerse the unit in water or any other liquid, or use when wet.

f Do not insert foreign objects into the AC outlet or the USB outlet.

Warning! To reduce the risk of fire f Do not operate near flammable materials, fumes

or gases. f Do not expose to extreme heat or flames.

Caution! To reduce the risk of injury or property damage:

f Remove appliance plug from outlet before working on the appliance.

f Do not attempt to connect or set up the unit or its components while operating your vehicle. Not paying attention to the road may result in a serious accident.

f Always use the inverter where there is adequate ventilation. Do not block ventilation slots.

f Always turn the inverter OFF by disconnecting it from the DC accessory outlet when not in use.

f Make sure the nominal powering voltage is 12V DC, center connection POSITIVE (+).

f When using this unit in a vehicle, check the vehicle owners manual for maximum power rating and recommended output. It may be necessary to change the vehicle accessory outlets in-line fuse to a higher rating. Do not install in engine compartment install in a well ventilated area.

f Do not use with positive ground electrical systems*. Reverse polarity connection will result in a blown fuse and may cause permanent damage to the inverter and will void warranty. * The majority of modern automobiles, RVs and trucks are negative ground.

f Keep in mind that this inverter will not operate high wattage appliances or equipment that produce heat, such as hair dryers, microwave ovens and toasters.

f Do not open the inverter: there are no user-serviceable parts inside.

f Do not use this inverter with medical devices. It is not tested for medical applications.

f Keep away from children. This is not a toy! f Install and operate unit only as described in this

Instruction Manual. f Do not use this inverter on a watercraft. It is not

qualified for marine applications. f Check unit periodically for wear and tear. Take to

a qualified technician for replacement of worn or defective parts immediately.

f Do not connect the unit to any utility power distribution systems or branch circuits.

f Do not use the inverter in temperatures over 104F (40C) or under 32F (0C).

f Failure to follow these safety guidelines will result in personal injury and/or the damage to the unit. It may also be void of the warranty.

f Read and understand this instruction manual before using this unit.

SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for the 400W Power inverter (PI400LA).

Warning! To reduce the risk of injury: f Follow these instructions and those published

by battery manfacturer and the manufacturer of any equipment you intend to use with this unit. Review cautionary markings on these products and on engine.

ENGLISH 13 INTRODUCTION Thank you for purchasing the PI400LA 400W Power Inverter with USB Charging Port. This inverter can be used to operate personal electronics such as: laptop computers, digital/video cameras, MP3 players, cell phones, PDAs, and more. It can also be used to recharge AC devices that have an appropriate recharging adapter with a local standard plug. Please read this Instruction manual carefully before use to ensure optimum performance and to avoid damage to this product.

FEATURES The front panel provides two LED indicators. The AC and USB outlets are ready to use. The green LED indicates power and proper operation of the inverter. The AC and USB outlets are ready to use. The red LED indicates inverter shutdown from an over-load or over-temperature fault.

The Power Pushbutton turns the inverter ON and OFF. It can also be used to force reset of inverter circuits by pressing it OFF (no LEDs are lit), then back ON again.

AC power is supplied through two standard three-prong type outlets. The outlets can accommodate either two- or three-pin AC plugs.

Controls and functions (Fig. A) 1. Power inverter 2. Battery clips (with cables) 3. DC accessory outlet plug 4. Output fault LED indicator 5. Input fault LED indicator 6. (On/Off) Power pushbutton 7. AC outlet 8. USB charging port with tethered cover 9. High-Speed cooling fan 10. (Red) positive (+) cable post 11. (Black) negative () cable post

How this inverter works This inverter is an electronic device that converts low voltage DC (direct current) electricity from a battery to AC (alternating current) household power. In designing this inverter, Black & Decker has incorporated design techniques previously employed in computer power supplies. The result of these design innovations is a smaller, lighter and easier-to-use power inverter.

The 400W Power Inverter with USB Charging Port converts power in two stages:

f The first stage is a DC-to-DC conversion process that raises the low voltage DC at the inverter input to 145V DC.

f The second stage is a MOSFET bridge stage that converts the high voltage DC into 220V, 50-60HZ AC.

Power inverter output waveform The AC output waveform of this inverter is known as a modified sine wave. It is a stepped waveform that has characteristics similar to the sine wave shape of utility power. This type of waveform is suitable for most AC loads, including linear and switching power supplies used in electronic equipment, transformers, and small motors. The modified sine wave produced by this inverter has an RMS (root mean square) voltage of 220V. Most AC voltmeters (both digital and analog) are sensitive to the average value of the waveform rather than the RMS value. They are calibrated for RMS voltage under the assumption that the waveform measured will be a pure sine wave. These meters will not correctly read the RMS voltage of a modified sine wave. Non-TRUE RMS meters will read about 20 to 30 volts low when measuring the output of this inverter. For accurate measurement of the output voltage of this unit, use a TRUE RMS reading voltmeter such as a Fluke 87, Fluke 8080A, Beckman 4410 or Triplett 4200.

CA modificada de la onda

220V del seno

CA de la onda 220V del seno

Modified sine wave 220V AC

Sine wave 220V AC

Fig. 1: AC Output Caution! Rechargeable Devices f Certain rechargeable devices are designed to

be charged by plugging them directly into an AC receptacle. These devices may damage the inverter or the charging circuit.

f If there is any sign that your appliance is behaving differently to that when connected to the normal power source then unplug and seek advice from your appliance manufacturer.

f When using a rechargeable device, monitor its temperature for the initial ten minutes of use to determine if it produces excessive heat.

f If excessive heat is produced, this indicates the device should not be used with this inverter.

f This problem does not occur with most battery-operated equipment. Most of these devices use a separate charger or transformer that is plugged into an AC receptacle.

f The inverter is capable of running most chargers and transformers.

MAXX SST Soft start technology

Black & Deckers Soft Start Technology gradually ramps up the inverters power to slowly start appliances that require a surge to get started. This gradual ramp up protects the inverter and the appliance, as well as the power source, from damage and failure.

14 ENGLISH OPERATING INSTRUCTIONS The Power Inverter must be connected only to batteries with a nominal output voltage of 12V. The unit will not operate from a 6V battery and will sustain permanent damage if connected to a 24V battery.

Always connect the PI400LA to the 12V DC power source before plugging any devices into the unit.

The standard AC and USB outlets allow simultaneous operation of multiple devices. Simply plug the equipment into the unit and operate normally. Ensure that the wattage of all equipment simultaneously plugged into the PI400LA does not exceed 400W continuous.

Connection to power source The power inverter comes equipped with a DC accessory outlet plug and battery clips for connection to a power source.

Connecting to a power source using the DC accessory outlet plug The DC Accessory outlet plug is suitable for operating the inverter at power outputs up to 100W. The tip of the plug is POSITIVE (+) and the side contact is NEGATIVE ().

Connect the inverter to the power source by inserting the DC accessory outlet plug firmly into the accessory outlet of a vehicle or other DC power source.

CAUTIONS f Connect directly to power source using the included

battery clips when operating above 100W. f Do not use with positive ground electrical systems. f Reverse polarity connection will result in a blown fuse

and may cause permanent damage to the inverter. Notes: Most vehicle accessory outlet circuits have fuses rated at 15A to 20A or greater. To operate at full wattage, either use the battery clip cable (supplied) or directly wire to the power source with user-supplied wire and fuse. The majority of modern automobiles, RVs and trucks are negative ground.

Once properly connected to a 12V DC power source and switched on, the green Power LED Indicator lights indicating that the Inverter is functioning properly. If either the yellow Input Fault LED Indicator or red Output Fault LED Indicator lights, indicating a fault condition exists, refer to the Troubleshooting section of this Instruction manual.

Connecting to a power source using the provided battery clips Use the provided battery clips (with cables) to connect the Power Inverter directly to the 12V power source as follows:

1. Check to make sure the inverters Power Pushbutton has been pressed OFF (no LEDs are lit) and that no flammable fumes are present in the installation area. 2. Connect the red cable to the RED post marked (+) on the back of the inverter . Connect the RED Battery Clip to the POSITIVE terminal of the battery. 3. Connect the black cable to the BLACK post marked () on the back of the inverter. Connect the BLACK Battery Clip to the NEGATIVE terminal of the battery. 4. Make sure that all connections between cables and terminals are secure.

Direct hardwiring to power source (optional connection method; hardware not included)

Warning! It is not recommended to install with cables longer than 10 feet (3m) as this can adversely effect the operation of your inverter.

Use #6 AWG wire if the inverter to power source connection is 6 feet or less. For cable lengths up to 10ft use #4 AWG wire. In either case, protect the positive (+) wire from shorts by installing a 35 ANL fuse or circuit breaker close to the DC power source (battery) terminal.

1. Check to make sure the inverters Power Pushbutton has been pressed OFF (no LEDs are lit) and that no flammable fumes are present in the installation area. 2. Identify the POSITIVE (+) and NEGATIVE () DC power source (battery) terminals. 3. Install a fuse holder or breaker close to the POSITIVE (+) terminal of the DC source (battery). 4. Connect a length of wire on one side of the fuse holder or circuit breaker. Connect the other end of the wire to the POSITIVE (+) terminal of the inverter. 5. Connect a length of wire between the inverters NEGATIVE () terminal and the DC power source NEGATIVE () terminal. 6. Connect a short length of wire to the other terminal of the fuse holder or circuit breaker. Mark it POSITIVE or +. 7. Connect the free end of the fuse or breaker wire to the POSITIVE (+) terminal of the DC power source (battery). 8. Insert a fuse appropriate to the inverter in the fuse holder. 9. Test the inverter by turning it on and plugging in a 100W lamp or equipment. 10. If the inverter is not properly operating, then refer to the Troubleshooting section of this manual.

CAUTION f Loose connectors may cause overheated wires

and melted insulation. f Check to make sure you have not reversed the

polarity. Damage due to reversed polarity is not covered by our warranty.

ENGLISH 15 Connection to load The Power Inverter is equipped with dual standard three- prong type outlets. Plug the cord from the equipment you wish to operate into the AC receptacle(s). Make sure the combined load requirement of your equipment does not exceed maximum continuous power. The Power Inverter is engineered to be connected directly to standard electrical and electronic equipment in the manner described above. Do not connect the Power Inverter to household or RV AC distribution wiring. Do not connect the Power Inverter to any AC load circuit in which the neutral conductor is connected to ground (earth) or to the NEGATIVE of the DC (battery) source.

Warning! Do not connect to AC distribution wiring.

Rated versus actual current draw of equipment Most electrical tools, appliances, electronic devices and audio/visual equipment have labels that indicate the power consumption in amps or watts. Be sure that the power consumption of the item to be operated is below 400W. If the power consumption is rated in amps AC, simply multiply by the AC volts (220) to determine the wattage.

Resistive loads are the easiest for the inverter to run; however, it will not run larger resistive loads (such as electric stoves and heaters), which require far more wattage than the inverter can deliver. Inductive loads (such as TVs and stereos) require more current to operate than do resistive loads of the same wattage rating.

For safety reasons, the unit will simply shut down if it is overloaded. To restart the unit, simply unplug all devices plugged into the unit; disconnect the unit from any 12V DC power source; then reconnect the unit BEFORE plugging the appliance back in.

Operation of the AC Outlets 1. Connect the inverter to a functioning 12V DC power source as described in this Instruction manual. If using the 12V DC vehicle accessory adapter, rotate the vehicle accessory plug slightly to make sure there is good contact. Make sure there is adequate space for proper ventilation of the inverter. 2. Press the power pushbutton to turn the unit ON. 3. The green power LED Indicator will light, indicating a proper connection. If either the yellow input fault LED Indicator or red output fault LED Indicator lights, indicating a fault condition exists, refer to the Troubleshooting section of this Instruction Manual. 4. If the Inverter does not work, make sure the ignition/ accessory switch is actually powering the accessory outlet. Some vehicles require the ignition switch to be turned on.

5. Plug the (220V AC) appliance into one of the inverters three-prong AC outlet and operate normally. Note: The Inverter will not operate appliances and equipment that generate heat, such as hair dryers, electric blankets, microwave ovens and toasters. Remember to disconnect the inverter from any power source when not in use.

Operation of the USB Charging port 1. Connect the inverter to a functioning 12V DC power source as described in this Instruction manual. If using the 12V DC vehicle accessory adapter, rotate the vehicle accessory plug slightly to make sure there is good contact. Make sure there is adequate space for proper ventilation of the inverter. 2. Press the power pushbutton to turn the unit ON. 3. The green power LED Indicator will light, indicating a proper connection. If either the yellow input fault LED Indicator or red output fault LED Indicator lights, indicating a fault condition exists, refer to the Troubleshooting section of this Instruction manual. 4. If the Inverter does not work, make sure the ignition/ accessory switch is actually powering the accessory outlet. Some vehicles require the ignition switch to be turned on. 5. Plug the USB-powered device into the inverters USB charging port and operate normally.

Note: Some mobile phones are provided with a data cable rather than a charging cable. This may result in your mobile phone not charging via the USB. Please check with the mobile phone manufacturer.

Note: This units USB charging port does not support data communication. It only provides 5V/500mA DC power to an external USB-powered device. Remember to disconnect the inverter from any power source when not in use.

PROTECTIVE FEATURES The inverter monitors the following conditions: a. Low battery voltage: This condition is not harmful to the inverter, but could damage the power source, so the inverter will automatically shut down when input voltage drops below 10.5V 0.3V DC. b. Input voltage too high: The inverter will automatically shut down when DC input voltage exceeds 15.5V 0.5V, as this can harm the unit. c. Thermal shutdown protection: The inverter will automatically shut down when the unit becomes overheated. d. Overload/Short circuit protection: The inverter will automatically shut down when a short circuit occurs.

OPERATING TIPS The inverter should only be operated in locations that are: a. Dry: Do not allow water or other liquids to come into contact with the inverter.

16 ENGLISH b. Cool: Surrounding air temperature should ideally be 10C and 20C (50F and 68F). Keep the inverter away from direct sunlight, when possible. c. Well-Ventilated: Keep the area surrounding the inverter clear to ensure free air circulation around the unit. Do not place items on or over the inverter during operation. The unit will shut down if the internal temperature gets too hot. The inverter will auto-reset after it cools down. d. Safe: Do not use the inverter near flammable materials or in any locations that may accumulate flammable fumes or gases. This is an electrical appliance that can briefly spark when electrical connections are made or broken.

CARE AND MAINTENANCE Storage 1. Ideal storage temperature range is 0C and 40C (32F and 104F). 2. Store and use in a cool, dry place with adequate ventilation for all-around air circulation. 3. Avoid locations that are exposed to heating units, radiators, direct sunlight, or excessive humidity or dampness.

Fuse replacement This inverter is equipped with multiple internal fuses. Normally, these fuses will not blow unless there is a serious problem inside the unit. Internal fuses are replaceable; however, only trained personnel should attempt fuse replacement. If the unit is damaged during fuse replacement, the warranty may be voided.

The fuse in the DC accessory outlet plug is user- replaceable. Make sure to first disconnect the outlet plug from any 12V DC power source; then replace the fuse with one of the same rating and type.

PROTECTING THE ENVIRONMENT Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

ACCESSORIES The performance of your tool depends on the accessory used. Black & Decker and Piranha accessories are engineered to high quality standards and designed to enhance the performance of your tool. By using these accessories you will get the very best from your tool.

SERVICE INFORMATION Black & Decker offers a full network of company-owned and authorized service locations. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. For more information about our authorized service centers and if you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you, or visit us at www.BlackandDecker-la.com

SPECIFICATIONS PI400LA Maximum continuous power: 400 Watts Surge capacity: 800 Watts USB port: 5V DC (500mA) Input voltage: 12.8V Low voltage alarm: 11.0V 0.3V DC Low voltage shutdown: 10.5V 0.3V DC Thermal shutdown: Automatic Wave form: Modified sine wave (MSW) Fuses: Internal / 12V DC accessory plug: 10A Input cables: Battery clip cables / 12V DC accessory plug Operating temperature: 10C and 20C (50F and 68F) Storage temperature: 0C and 40C (32F and 104F) Operating/Relative humidity: 5% to 95% non-condensing

ENGLISH 17

Solamente para propsito de Argentina: Importado por: Black & Decker Argentina S.A. Pacheco Trade Center Colectora Este de Ruta Panamericana Km. 32.0 El Talar de Pacheco Partido de Tigre Buenos Aires (B1618FBQ) Repblica de Argentina No. de Importador: 1146/66 Tel.: (011) 4726-4400

Imported by/Importado por: Black & Decker do Brasil Ltda. Rod. BR 050, s/n- Km 167 Dist. Industrial II Uberaba MG Cep: 38064-750 CNPJ: 53.296.273/0001-91 Insc. Est.: 701.948.711.00-98 S.A.C.: 0800-703-4644

Solamente para propsitos de Colombia Importado por: Black & Decker de Colombia, S.A. Carrera 85D # 51-65, Bodega 23 Complejo Logstico San Cayetano Bogot - Colombia Tel.: 744-7100

Solamente para propsito de Chile: Importado por: Black & Decker de Chile, S.A. Av. Pdte. Eduardo Frei M. 6001-67 Conchal Santiago de Chile Tel.: (56-2) 687 1700

Impreso en China Impresso em China Printed in China

11/06/13

Solamente para propsito de Mxico: Importado por: Black & Decker S.A. de C.V. Avenida Antonio Dovali Jaime # 70 Torre B Piso 9 Colonia La Fe, Santa F Delegacin Alvaro Obregn, Mxico D.F. 01210 Tel. (52) 555-326-7100 R.F.C.: BDE810626-1W7

Black & Decker del Per S.A. Av. Enrique Meiggs 227. Pque. Industrial - Callao Tel.: (511) 614-4242 RUC 20266596805

TROUBLESHOOTING

Common audio/visual problems Problem Explanation/Recommendation Buzzing sound in audio systems

Some inexpensive stereo systems and boom boxes make a buzzing sound when operated from the inverter, because the power supply in the electronic device does not properly filter the modified sine wave produced by the inverter. The only solution to this problem is to use a sound system that has a higher quality power supply.

Problem: Television interference The inverter is shielded to minimize interference with TV signals. However, in some instances, some interference may still be visible, especially when the TV signal is weak. Try the following to improve the picture: 1. Move the Inverter as far away as possible from the TV set, the antenna, and the antenna cables. Use a short AC extension cord, if necessary. 2. Adjust the orientation of the antenna cables, and the TV power cord to minimize interference. 3. Make sure that the antenna feeding the TV provides an adequate (snow-free) signal and that high quality, shielded antenna cable is used.

Common power output problems Possible cause Recommendation Battery voltage below 10.5V Recharge battery or check DC power supply. Equipment being operated draws too much power

f Reduce load to maximum 400W. f Connect directly to power source using the included battery clips when

operating above 100W. Inverter in thermal shutdown condition

Allow inverter to cool down. Ensure there is adequate ventilation around the load is no more than 400W for continuo

Manualsnet FAQs

If you want to find out how the PI400LA-B3 Black & Decker works, you can view and download the Black & Decker PI400LA-B3 Inverter Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Black & Decker PI400LA-B3 as well as other Black & Decker manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Black & Decker PI400LA-B3. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Black & Decker PI400LA-B3 Inverter Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Black & Decker PI400LA-B3 Inverter Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Black & Decker PI400LA-B3 Inverter Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Black & Decker PI400LA-B3 Inverter Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Black & Decker PI400LA-B3 Inverter Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.