Black & Decker 1180-220 Drill Instruction Manual PDF

1 of 8
1 of 8

Summary of Content for Black & Decker 1180-220 Drill Instruction Manual PDF

Black & Decker (U.S.) Inc. 701 East Joppa Road, Towson, Maryland 21286 Printed in U.S.A. (FEB96-CD-1) Form No. 154566 Copyright 1996

154566/1180-220 5/17/02 1:32 PM Page 2

Instruction Manual 1180-220 1311-220 VSR Holgun Drills

154566/1180-220 5/17/02 1:32 PM Page 3

Getting the most out of your tool. Please take time to read this manual and pay particular attention to the safety rules weve provided for your protection. Dont forget to send in your owners registration card. If you have any questions about your tool please call:

1-800-9-BD TOOL (1-800-923-8665)

1180-220 (3/8") VSR HOLGUN DRILL

1311-220 (1/2") VSR HOLGUN DRILL

CHUCK

REVERSING LEVER

TRIGGER SWITCH

LOCKING BUTTON

CHUCK

REVERSING LEVER

TRIGGER SWITCH

LOCKING BUTTON

SIDE HANDLE 220 VOLT PLUG

220 VOLT PLUG

154566/1180-220 5/17/02 1:32 PM Page 4

1

KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors should be kept away from work area.

STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-up place out of reach of children.

DONT FORCE TOOL. It will do the job better and safer at the rate for which it was intended.

USE RIGHT TOOL. Dont force small tool or attachment to do the job of a heavy-duty tool. Dont use tool for purpose not intended.

DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recom- mended when working outdoors. Wear protective hair covering to contain long hair.

USE SAFETY GLASSES. Also use face or dust mask if operation is dusty. DONT ABUSE CORD. Never carry tool by cord or yank it to disconnect from

receptacle. Keep cord from heat, oil, and sharp edges. SECURE WORK. Use clamps or a vise to hold work. Its safer than using

your hand and it frees both hands to operate tool. DONT OVERREACH. Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and

safer performance. Follow instructions for lubricating and changing acces- sories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.

DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when changing accessories, such as blades, bits, cutters.

REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

AVOID UNINTENTIONAL STARTING. Dont carry tool with finger on switch. Be sure switch is off when plugging in.

EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry

WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following:

READ ALL INSTRUCTIONS

Double Insulation Double insulated tools are constructed throughout with two separate layers of electrical insulation or one double thickness of insulation between you and the tools electrical system. Tools built with this insulation system are not intended to be grounded. As a result, your tool is equipped with a two prong plug which permits you to use extension cords without concern for maintaining a ground connection.

NOTE: Double insulation does not take the place of normal safety precau- tions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool.

CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or replace damaged cords.

Safety Instructions For All Tools KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. Dont expose power tools to rain.

Dont use power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence of flammable liquids or gases.

GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, and refrigerator enclosures.

FOR YOUR SAFETY - ALL TOOLS

154566/1180-220 5/17/02 1:32 PM Page 1

2

the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more AWG Than Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended

OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

STAY ALERT. Watch what you are doing. Use common sense. Do not oper- ate tool when you are tired.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized ser- vice center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off.

CAUTION: When drilling or driving into walls, floors or wherever live electri- cal wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by insulated grasping surfaces to prevent electric shock if you drill or drive into a live wire.

SAVE THESE INSTRUCTIONS

Side Handle (1311-220) CAUTION: Always use side handle when provided and hold drill with both hands. A side handle is supplied with all 1/2" and some 3/8" drills. In most cases, it clamps to the front of the gear case as shown in Figure 1 and can be rotated 360 to permit right or left hand use.

Switch To start drill, depress the trigger switch, shown in Figure 2. To stop drill, release the switch. To lock the trigger switch in the ON position for continu- ous operation, depress the trigger switch and push up the locking button. The tool will continue to run. To turn the tool OFF, from a locked ON condi- tion, squeeze and release the trigger once. Before using the tool (each time), be sure that the locking button release mechanism is working freely.

Do not lock the switch ON when drilling by hand so that you can instantly release the trigger switch if the bit binds in the hole. The locking button is for use only when the drill is mounted in a drill press stand or other wise held stationary. Be sure to release the locking mechanism before disconnecting the plug from the power supply. Failure to do so will cause the drill to start immediately the next time it is plugged in. Damage or injury could result.

The variable speed trigger switch permits speed control. The farther the trig- ger switch is depressed, the higher the speed of the drill.

NOTE: Use lower speeds for starting holes without a centerpunch, drilling in metal, plastics or ceramics, or driving screws. Higher speeds are better for drilling in wood and composition board and for using abrasive and polishing accessories.

TOOL OPERATION

154566/1180-220 5/17/02 1:32 PM Page 2

3

The reversing lever is used to reverse the drill for backing out screws or jammed bits. It is located above the trigger, shown in Figure 2. To reverse the drill, turn it OFF and push the reversing lever to the left (when viewed from the chuck end). To position the lever for forward operation, turn the drill OFF and push the lever to the right.

Chuck To insert bit, open chuck jaws by turning collar with fingers and insert shank of bit about 3/4" into chuck. Tighten chuck collar by hand. Place chuck key in each of the three holes and tighten in clockwise direction. Its impor- tant to tighten chuck with all three holes. To release bit, turn chuck key counterclockwise in just one hole, then loosen the chuck by hand.

Chuck Key Holder (May be installed already)

1. Push double hole end of holder through slot in other end of holder (Figure 3).

2. Slip loop over electric plug and draw loop tight around cord (Figure 4). 3. Push ends of chuck key handle through two holes in end of holder

(Figure 5).

Chuck Removal 1. turn off tool and DISCONNECT FROM POWER SUPPLY. 2. Place chuck key in chuck as shown in Figure 6. 3. Using a wooden mallet or similar object, strike key sharply in a clock-

wise direction. This will loosen screw inside chuck (Figure 6). 4. Open chuck jaws fully. Insert screwdriver (or 3/16" hex wrench if

required) into front of chuck between jaws to engage screw head.

REVERSING LEVER

TRIGGER SWITCH

LOCKING BUTTON

Figure 2

Figure 1

Figure 3

Figure 5

Figure 4

154566/1180-220 5/17/02 1:32 PM Page 3

4

5. Remove screw by turning clockwise (left-hand thread). 6. Place key in chuck as shown in Figure 7. 7. Using a wooden mallet or similar object, strike key sharply in a counter-

clockwise direction. This will loosen chuck so that it can be unscrewed by hand (Figure 7).

Drilling 1. Always turn off tool and disconnect from power supply when attaching

or changing bits or accessories. 2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits,

power auger bits, or hole saws. For METAL, use high speed steel twist drill bits or hole saws. For MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits

3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a back-up block to prevent damage to the material.

4. Always apply pressure in a straight line with the bit. Use enough pres- sure to keep the drill bit biting, but do not push hard enough to stall the motor or deflect the bit.

5. Hold tool firmly to control the twisting action of the drill.

6. IF DRILL STALLS, it is usually because it is being overloaded. RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL THIS CAN DAMAGE THE DRILL.

7. To minimize stalling on breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of the hole.

8. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent jamming.

9. With variable speed drills there is no need to center punch the point to be drilled. Use a slow speed to start the hole and accelerate by squeez- ing the trigger harder when the hole is deep enough to drill without the bit skipping out. Operate at full speed after starting the bit.

Drilling in Wood Holes in wood can be made with the same twist drills used for metal. These bits may overheat unless pulled out frequently to clear chips from the flutes. For larger holes, use spade bits, power auger bits, or hole saws. Work that is likely to splinter should be backed up with a block of wood.

Drilling in Metals Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulphurized cutting oil or lard oil; bacon grease will also serve the purpose.

Drilling in Masonry Use carbide tipped masonry bits at low speeds. Keep even force on the drill but not so much that you crack the brittle materials. A smooth, even flow of dust indicates the proper drilling rate.

Figure 6 Figure 7

154566/1180-220 5/17/02 1:32 PM Page 4

5

Lubrication All ball and sleeve bearings used are factory lubricated to last the life of the bearings. All needle bearings used received their lubrication from the grease in the gear case. Clean and relubricate gear case yearly or whenever servic- ing requires the gear case to be removed. Use type and quantity of grease shown on Parts Bulletin packed with your tool. The gear case is removed by removing the three screws from the front of the tool. If the chuck is too large to permit removal of the two top screws, see instructions for chuck removal.

Motor Brushes Your drill uses the B&D CHECKPOINT brush system. The tool will stop when the brushes wear out. This prevents damage to the motor.

IMPORTANT! To assure product safety and reliability, particularly for double Insulated tools, repairs, maintenance and adjustment (excluding maintenance described in this manual) should be performed by B&D service centers or authorized service centers, using identical B&D replacement parts.

Accessories Recommended accessories for use with your tool are available at extra cost from your distributor or local service center.

CAUTION: The use of any non-recommended accessory may be hazardous.

If you need any assistance in locating any accessory call 1-800-9-BD TOOL: (1-800-923-8665) or contact Black & Decker (U.S.) Inc., Consumer Services Department, 626 Hanover Pike, P.O. Box 618, Hampstead, MD 21074.

MAINTENANCE

One Year Service/Safety Check All B&D tools for Industry and Construction are covered under a service/safety check program where B&D will inspect your tool for safety and provide necessary maintenance or repairs, including normal wear and tear parts, for one year, FREE OF CHARGE.

Full Warranty All B&D tools for Industry and Construction are warranted to be free of any defects in materials or workmanship. Upon thorough examination of tool, B&D will repair or replace, at our option, any product that is determined to be defective.

Conditions The service/safety check and the warranty do not apply to: repairs made or attempted by anyone other than an authorized B&D service location; misuse, abuse, neglect, improper application of the tool; missing parts; or normal wear and tear (after first year of ownership). Please return the complete unit, trans- portation prepaid, to any B&D factory owned or B&D authorized service center location (list provided with tool or see Yellow Pages under Tools Electric).

Every B&D tool is of the highest quality. If you wish to contact us regarding this product, please call to

Manualsnet FAQs

If you want to find out how the 1180-220 Black & Decker works, you can view and download the Black & Decker 1180-220 Drill Instruction Manual on the Manualsnet website.

Yes, we have the Instruction Manual for Black & Decker 1180-220 as well as other Black & Decker manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Instruction Manual should include all the details that are needed to use a Black & Decker 1180-220. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Black & Decker 1180-220 Drill Instruction Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Black & Decker 1180-220 Drill Instruction Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Black & Decker 1180-220 Drill Instruction Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Black & Decker 1180-220 Drill Instruction Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Black & Decker 1180-220 Drill Instruction Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.