Contents

BenQ RM7501K User Manual PDF

1 of 60
1 of 60

Summary of Content for BenQ RM7501K User Manual PDF

RM7501K/RM8601K Interactive Flat Panel User Manual

Disclaimer BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents of this document. BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes.

Copyright Copyright 2018 BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

Table of Contents i

Table of Contents

Safety warnings and precautions ...................................... 1 Important safety instructions............................................ 2

Notes on the LCD panel of this display..................................... 2 Safety notice for remote control................................................. 3 Battery safety notice ....................................................................... 3 BenQ ecoFACTS.............................................................................. 4

Package contents ................................................................. 5 Setting up the display .......................................................... 6

Mounting the display ....................................................................... 6 Parts of the display and their functions .......................... 8

Front/Rear panel ............................................................................. 8 Input/output terminals.................................................................... 9 Remote control............................................................................. 10 Using the remote control ........................................................... 12

Connection ......................................................................... 13 Connecting audio/video signals ................................................. 13 Connecting the multimedia inputs............................................ 16 Connecting the touch module................................................... 17 Connecting power........................................................................ 18 Installing and Removing OPS module ...................................... 19

Using the touch screen..................................................... 20 Important instructions for using the touch screen............... 24

Basic operations................................................................. 25 Turning the display on or off ..................................................... 25 Initial Setup..................................................................................... 25 Sidebar Menu................................................................................. 26 Switching input signals ................................................................. 27 Eye Care solutions..................................................................... 28 Downloading software ................................................................ 28 Setting up Internet connection.................................................. 28 Updating software ........................................................................ 29 Restoring to the default settings ............................................... 30 Adjusting audio volume level ..................................................... 30

Table of Contentsii

The OSD (On-Screen Display) menu ........................... 31 OSD menu overview ................................................................... 31 Operations in the OSD menu.................................................... 32 Picture menu................................................................................ 33 Sound menu................................................................................. 34 Setting menu................................................................................ 35

Working with Android OS.............................................. 37 Settings......................................................................................... 38 Local Application .................................................................... 39 BenQ Suggest ........................................................................... 40 Browser ........................................................................................ 41 ES File Explorer ....................................................................... 42 InstaQPrint .................................................................................. 43 InstaShare ................................................................................... 44 Multimedia................................................................................... 46 WPS Office .................................................................................. 47

Product information.......................................................... 49 Specifications.................................................................................. 49 Dimensions..................................................................................... 52 Supported input ............................................................................ 54

Troubleshooting ................................................................. 55

7/21/20

Safety warnings and precautions 1

Safety warnings and precautions

The mains plug of the power supply cord shall remain readily operable. The AC receptacle (mains socket outlet) shall be installed near the equipment and shall be easily accessible. To completely disconnect this equipment from the AC mains, disconnect the power cord plug from the AC receptacle.

Do not place this display on an uneven, sloping or unstable surface (such as a trolley) where it may fall and cause damage to itself or others.

Do not place this display near water, like a spa or pool, or in a position which will allow the splashing or spraying of water onto the display, like in front of an open window where rain water may enter.

Do not install this display in a confined space without proper ventilation and air circulation, such as in a closed cabinet. Allow proper space around the display for dissipating heat inside. Do not block any openings and vents on the display. Overheating may result in hazards and electric shock.

Installation of this display should only be performed by a qualified technician. Failure to install this display properly may cause injuries and damages to the personnels and the display itself. Check the installation regularly and maintain the display periodically to ensure the best working condition.

Use only the accessories approved or recommended by the manufacturer to mount this display. Using wrong or unsuitable accessories may cause the display to fall and result in serious personal injuries. Make sure that the surface and fixing points are strong enough to sustain the weight of the display.

To reduce the risk of electric shock, do not remove covers. No user serviceable parts inside. Refer servicing to qualified service personnel.

To prevent personal injuries, mounting the display or installing desktop stands is required before use.

THIS EQUIPMENT MUST BE GROUNDED To ensure safe operation, the three-pin plug must be inserted only into a standard three-pin power outlet which is effectively grounded through normal household wiring. Extension cords used with the equipment must have three cores and be correctly wired to provide connection to the ground. Wrongly wired extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power outlet is grounded or that the installation is completely safe. For your safety, if you are in any doubt about the effective grounding of the power outlet, please consult a qualified electrician.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Important safety instructions2

Important safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's

instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Notes on the LCD panel of this display The Liquid Crystal Display (LCD) panel of this display has a very thin protective layer of glass which is liable to marking or scratching, and cracking if struck or pressured. The liquid crystal substrate is also liable to damage under excessive force or extreme temperatures. Please handle with care.

The response time and brightness of the LCD panel may vary with the ambient temperature.

Avoid placing the display in direct sun or where direct sun or spot lighting will shine onto the LCD panel, as the heat may damage the panel and the external casing of the display, and the bright light will make viewing the display more difficult than necessary.

The LCD panel consists of individual pixels to display images and is manufactured according to the design specifications. While 99.9% of these pixels work normally, 0.01% of the pixels may remain constantly lit (in red, blue or green) or unlit. This is a technical limitation of the LCD technology and is not a defect.

LCD screens, like plasma (PDP) and conventional CRT (Cathode Ray Tube) screens, are also susceptible to 'screen burn-in' or 'image retention' which can be found on the

Important safety instructions 3

screen as visible fixed lines and shades. To avoid such damage to the screen, avoid displaying still images (like On-Screen Display menus, TV station logos, fixed/inactive text or icons) for more than 30 minutes. Change the aspect ratio from time to time. Fill the entire screen with the image and eliminate the black bars whenever possible. Avoid displaying images in 16:9 aspect ratio over a long period of time, otherwise there may be visible burn marks on the screen as two vertical lines. Note: Under certain circumstances, condensation may occur on the inner side of the cover glass, it's a natural phenomenon and will not affect the operation of the display. This condensation will usually disappear after around 2 hours of normal operation.

RM series does not offer image retention function, for more information, please refer to installation guide.

RM series does not support portrait use; portrait use may cause display damage. BenQ warranty will not cover faulty usage.

Safety notice for remote control Do not put the remote control in the direct heat, humidity, and avoid fire. Do not drop the remote control. Do not expose the remote control to water or moisture. Failure to do so could result in malfunction.

Confirm there is no object between the remote control and the remote sensor of the product.

When the remote control will not be used for an extended period, remove the batteries.

Battery safety notice The use of the wrong type of batteries may cause chemical leaks or explosion. Please note the following: Always ensure that the batteries are inserted with the positive and negative terminals in the correct direction as shown in the battery compartment.

Different types of batteries have different characteristics. Do not mix different types. Do not mix old and new batteries. Mixing old and new batteries will shorten battery life or cause chemical leaks from the old batteries.

When batteries fail to function, replace them immediately. Chemicals which leak from batteries may cause skin irritation. If any chemical matter seeps out of the batteries, wipe it up immediately using a dry cloth, and replace the batteries as soon as possible.

Due to varying storage conditions, the battery life for the batteries included with your product may be shortened. Replace them within 3 months or as soon as you can after initial use.

There may be local restrictions on the disposal or recycling of batteries. Consult your local regulations or waste disposal provider.

The product is designed for IT power distribution system with phase-to-phase voltage 230V.

Important safety instructions4

BenQ ecoFACTS BenQ has been dedicated to the design and development of greener product as part of its aspiration to realize the ideal of the "Bringing Enjoyment 'N Quality to Life" corporate vision with the ultimate goal to achieve a low-carbon society. Besides meeting international regulatory requirement and standards pertaining to environmental management, BenQ has spared no efforts in pushing our initiatives further to incorporate life cycle design in the aspects of material selection, manufacturing, packaging, transportation, using and disposal of the products. BenQ ecoFACTS label lists key eco-friendly design highlights of each product, hoping to ensure that consumers make informed green choices at purchase. Check out BenQ's CSR Website at http://csr.BenQ.com/ for more details on BenQ's environmental commitments and achievements.

Package contents 5

Package contents Open the sales package and check the contents. If any item is missing or damaged, please contact your dealer immediately.

LCD display Power cord x6 D-Sub (15-pin) cable x1 Remote control

USB cable x1 HDMI cable x1 AAA battery x 2 Touch pen x 2

Quick start guide

The type of power cord supplied may differ from that illustrated depending on your region of purchase.

Before discarding the package, check that you haven't left any accessories inside the box. Dispose of packaging materials wisely. You can recycle the cardboard carton. Consider storing

the package (if possible) for future transport of the display. Do not leave plastic bags within reach of young children or babies.

HDMITOUCH USBMEDIA USBPC USB

Setting up the display6

Setting up the display Mounting the display You can install the display on a vertical surface with a suitable wall mounting bracket or on a horizontal surface with the optional desktop stands. Please pay attention to the following notes during installation: This display should be installed by at least two adult persons. Attempting to install this display by only one person may result in danger and injuries.

Refer the installation to qualified technicians. Improper installation may cause the display to fall or malfunction.

Installing the display on a wall 1. Place a clean, dry and lint-free cloth on a flat, horizontal and object-free surface.

Make sure that the size of the cloth is larger than the display. 2. Gently lay the display on the cloth with the LCD screen facing down. 3. Remove the desktop stands from the display if installed. 4. Identify the wall mounting screw holes on the back of the display as shown in the

illustration.

5. Install the wall mounting bracket on the display and attach the display to the wall according to the mounting brackets instructions. The length of the screw should exceed the thickness of the wall mounting bracket by at least 10 mm. Make sure that all screws are tightened and secured properly. (Recommended torque: 470 - 635Ncm). The mounting means should be strong enough to bear the weight of the display.

RM7501K RM8601K

600568,4 568,4

40 0

29 7,

7 38

7, 6

4-M8*20L

*Screw type: M8

4-M8*20L

645 700 645

37 8

40 0

45 3

*Screw type: M8

Thickness of the wall mounting bracket

10 mm (0.39")

LCD display

Setting up the display 7

To maintain proper ventilation, keep at least 10 mm of clear space from the back cover of the display to the wall.

Please consult a professional technician for wall mount installations. The manufacturer accepts no liability for installations not performed by a professional technician.

10 mm (0.39")

Parts of the display and their functions8

Parts of the display and their functions Front/Rear panel

No. Name Description

TOUCH USB Connects the USB cable from the display to a computer to use the touch module.

AUDIO OUT Connects to an external audio device (such as a speaker, stereo system, or headphone) to output the audio that is supplied by the video source.

MIC Connects to a microphone.

USB2.0 Accesses multimedia files on USB drives directly.

USB2.0 USB3.0

Accesses multimedia files on USB drives directly. USB3.0

HDMI 4(MHL) Receives HDMI signals from an external device or an MHL compatible device.

Power Switch

Used to isolate the power supply from the system. When the switch is set to ON (I), the system will automatically enter standby mode.

When the switch is set to OFF (O), this will completely cut off the power supply.

7

8

1

2

3

4

5

6

7

8

9

Parts of the display and their functions 9

Input/output terminals

MENU Press to open or close the sidebar menu.

Ambient Light Sensor

Detects the ambient room light conditions to automatically adjust the display backlight brightness.

Remote Control Sensor Receives the signal from the remote control.

POWER Press to turn the display on or off.

Power-in Connects with the supplied power cord.

10

11

12

13

14

7 8

No. Name Description

RS232 Serial interface, used for mutual transfer of data between devices.

PC AUDIO Receives audio signals from an external device.

VGA Receives analog RGB signals from an external device (such as a computer).

LAN Connects to a network using the Ethernet cable.

HDMI OUT Connects to display devices with an HDMI input (HDMI 1, HDMI 2, HDMI 3, or OPS input).

HDMI 3 Receives HDMI signals from an external device.

HDMI 2 Receives HDMI signals from an external device.

HDMI 1 Receives HDMI signals from an external device.

1

2

3

4

5

6

7

8

Parts of the display and their functions10

Remote control POWER Turns the display on or off.

INPUT Selects an input source.

CH RETURN Returns to the previous program channel (This function is only supported for certain models).

INFO Shows the current input source and resolution.

FAV Shows the favorite program channel (This function is only supported for certain models).

16:9 Changes the aspect ratio of the display image.

MULTI-MEDIA buttons Used to control the media playback.

Numeric buttons (0-9) Performs as numeric buttons when the OSD menu is on.

SCREEN SHOT Captures a screenshot and automatically save it to the displays internal memory, or to a USB drive if plugged.

CHLIST ( ) Deletes a character / displays program list (This function is only supported for certain models).

MUTE Turns on or off the mute function.

VOL- / VOL+ Turns down/up the volume.

CH+ / CH- Selects the program channel.

2 3

1

7

8

9

12

16 14

18

22

21

23

5 6

4

10

13

11

17

15

19

24

20

1

2

3

4

5

6

7

8

9

10

11

12

13

Parts of the display and their functions 11

Press and hold the CH+ button to enable/disable Keypad Lock function.

Press and hold the CH- button to enable/disable IR Lock function.

WPS Switches the system into Android OS, then opens the WPS office app.

M-Player Switches the system into Android OS, then opens the Multimedia app.

Write Switches the system into Android OS, then opens the EZWrite 4.1 Lite app.

Eye Care Sets the display mode to Eyecare mode. Refer to Picture menu on page 33.

BLANK Hides the image (the screen becomes blank) when the OSD menu is off. Press again to resume normal display.

MENU Opens or closes the OSD menu.

FREEZE Freezes the image when the OSD menu is off.

OK Confirms your selection or save changes.

Cursor keys (///) Scrolls through settings and options in the OSD menu when the OSD menu is on.

Back button ( ) Returns to the previous page (in Android OS).

Home button ( ) Returns to the home screen (in Android OS).

2 3

1

7

8

9

12

16 14

18

22

21

23

5 6

4

10

13

11

17

15

19

24

20

14

15

16

17

18

19

20

21

22

23

24

The users can keep pushing Eye Care on the remote control and then the eye care mode will be shown on the top-left corner of the display, which is the low blue light mode.

Parts of the display and their functions12

Using the remote control Installing remote control batteries

Remote control usage tips Point and aim the top front of the remote control directly at the displays remote control sensor window when you press the buttons.

Do not let the remote control become wet or place it in humid environments (like bathrooms).

If the displays remote control sensor window is exposed to direct sunlight or strong light, the remote control may not operate properly. In this situation, change the light source, readjust the angle of the display or operate the remote control from a location closer to displays remote control sensor window.

1. Open the remote control battery compartment cover.

2. Insert the supplied batteries ensuring that the positive and negative marked battery terminals match the (+) and (-) marks in the battery compartment.

The supplied batteries are provided for your convenience so that you can operate the display straight away. You should replace them as soon as possible.

3. Refit the battery compartment cover.

30 30

Connection 13

Connection Connecting audio/video signals Pay attention to the following notes when you connect cables: Please turn off all devices. Familiarize yourself with the audio/video ports on the display and the devices you want to use. Be aware that incorrect connections may adversely affect picture quality.

Do not remove cables from the ports by pulling the cable itself. Always grasp and pull the connectors at the end of the cable.

Ensure that all cables are fully inserted and firmly seated.

Connecting the VGA input 1. Connect the VGA jack on the display to the VGA output jack on a computer using a

D-Sub (15-pin) cable. 2. Connect the computers audio output jack to the PC AUDIO jack on the display

using a suitable audio cable. 3. To view images from this input, press the INPUT button on the remote control, or

tap the Input Source ( ) icon in the sidebar menu, and then select VGA.

The audio cable is not supplied and should be purchased separately.

Audio cable D-Sub (15-pin) cable

Computer

Connection14

Connecting the digital inputs 1. Connect the HDMI output jack of a computer or A/V device (such as a VCR or DVD

player) to the HDMI 1, HDMI 2, HDMI 3, or HDMI 4(MHL) input jack on the display using the supplied HDMI cable.

2. To view video image from this input, press the INPUT button on the remote control, or tap the Input Source ( ) icon in the sidebar menu, and then select HDMI 1, HDMI 2, HDMI 3, or HDMI 4.

All HDMI ports support 4K resolution.

Computer

HDMI cable

VCR DVD Player

Connection 15

Connecting the mobile device inputs 1. Connect the Micro-USB output jack of an MHL compatible device (such as a Smart-

phone or tablet) to the HDMI 4(MHL) input jack on the display using an MHL cable.

2. To view video image from this input, press the INPUT button on the remote control, or tap the Input Source ( ) icon in the sidebar menu, and then select HDMI 4.

The MHL cable is not supplied and should be purchased separately.

MHL cable MHL compatible device

Connection16

Connecting the multimedia inputs To view multimedia files on the USB flash drive:

1. Plug the USB flash drive in the USB2.0 or USB3.0 port. 2. A dialog box appears on the screen. Select Ok to enter the multimedia mode.

The USB flash drives are not supplied and should be purchased separately.

USB flash drive

Connection 17

Connecting the touch module Connect the TOUCH (type B) jack on the display to the USB port of a computer using the supplied USB cable. The touch module of the display supports easy Plug-and-Play operation. There is no need to install additional drivers on the computer.

Avoid blocking the touch screen frame (where sensors are located) when initiating the touch module.

It is highly recommended that you connect the display to the PC or laptop directly. Avoid connecting the display to a face plate device which may cause failures in touch operations.

If any ghost image occurs, please try to unplug and then re-plug all USB cables. If the failure image still exists, use another USB type B to A cable.

USB cable

Computer

Connection18

Connecting power Plug one end of the power cord into the Power-in jack on the display and the other end into an appropriate power outlet (if the outlet is switched, turn on the switch).

The supplied power cord is suitable for use with 110-240V AC power only. The power cord and outlet illustrated may differ from the ones used in your region. Only use an appropriate power cord for your region. Never use a power cord which appears

damaged or frayed, or change the plug type on the power cord. Be aware of the power loading when you use extension cords or multiple outlet power boards. There are no user serviceable parts in this display. Never unscrew or remove any covers.

There are dangerous voltages inside the display. Turn off the power and unplug the power cord if you intend to move the display.

Connection 19

Installing and Removing OPS module The illustration shown below is for your reference. The actual content, pre-installed applications and available services may vary by the product supplied for your region. OPS module should be purchased separately. To install the OPS module: 1. Power off the display. 2. Remove the two screws to remove the OPS cover.

3. Insert the OPS module and then secure with screws.

To remove the OPS module: 1. Power off the display. 2. Remove the two screws and pull out the OPS module.

Keep the OPS cover for future use.

Using the touch screen20

Using the touch screen You can use the optical touch screen to control your operating system. The touch screen can emulate basic mouse functions and supports multi-touch functions for Windows 7/ 8*. The following table shows a list of gestures you can use on the touch screen.

Ensure that you have installed the USB cable on the display to a computer. *Multi-touch functions are only supported by Windows 8, Windows 7 - Home Premium,

Professional, Enterprise and Ultimate versions. For Windows XP, Windows Vista and Windows 7 - Starter and Home Basic versions, multi-touch are not supported.

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

OS functions Gesture actions

For Windows XP, Windows Vista, Windows 7, Windows 8.1, and Windows 10

Click

Tap the screen once.

Double-click

Tap the screen twice.

Right-click

1. Press on the target. 2. Hold and wait for a blue ring to appear. 3. Release your finger.

Drag

Drag one finger left or right.

Using the touch screen 21

For Windows Vista, Windows 7, Windows 8.1, and Windows 10

Selection

Drag one finger left or right.

Pan up / Pan down / Back / Forward

Quickly drag your finger (Flick) in a desired direction.

Multi-touch functions For Windows 7 - Home Premium, Professional, Enterprise and Ultimate versions

Right-click

1. Press on the target. 2. Tap the screen with another finger. 3. Release the second finger.

Scrolling

Drag one or two fingers up or down.

Zoom

Move two fingers apart or toward each other.

OS functions Gesture actions

or

Using the touch screen22

Supported by specific applications

Move two fingers in opposing directions. Use one finger to pivot around another.

Supported by specific applications

Tap two fingers simultaneously. The target should be the midpoint between the fingers.

For Windows XP, Windows Vista and Windows 7

Wakeup from Windows sleep mode (S3)

Press and hold for 4 seconds.

OS functions Gesture actions

Gesture Description

For Windows 8 Press and hold to learn This touch interaction causes detailed information or teaching visuals (for example, a tooltip or context menu) to be displayed without a commitment to an action. Anything displayed this way should not prevent users from panning if they begin sliding their finger.

Tap for primary action Tapping on an element invokes its primary action, for instance launching an application or executing a command.

Using the touch screen 23

Slide to pan Slide is primarily used for panning interactions but can also be used for moving, drawing or writing. Slide can also be used to target small, densely packed elements by scrubbing (sliding the finger over related objects such as radio buttons).

Swipe to select, command, and move Sliding the finger a short distance, perpendicular to the panning direction, selects objects in a list or grid (ListView and GridLayout controls). Display the AppBar with relevant commands when objects are selected.

Pinch and stretch to zoom While the pinch and stretch gestures are commonly used for resizing, they also enable jumping to the beginning, end, or anywhere within content with Semantic Zoom. A Semantic Zoom control provides a zoomed out view for showing groups of items and quick ways to dive back into them.

Turn to rotate Rotating with two or more fingers causes an object to rotate.

Gesture Description

Using the touch screen24

Important instructions for using the touch screen Please clean the frame when there is sign of malfunction on the touch screen. Before you clean the screen, make sure the display is turned off, and unplug the power cord.

Remove dust or dirt from the screen and the infrared plastic filter periodically. It is suggested using a small amount of alcohol to clean the infrared plastic filter.

To avoid damage to the screen, never use any type of abrasive materials to wipe the screen.

Use a neutral detergent to clean the touch screen. Avoid using detergents with erosive substance, such as banana oil or ammonia.

Moisten a clean soft, lint-free cloth with a neutral detergent and then clean the touch screen.

Do not spray a detergent on the screen surface or the body directly. It may result in a short circuit to the touch screen.

Keep the touch screen out of direct sunlight or spotlights.

Basic operations 25

Basic operations Turning the display on or off Before turning on the display, make sure the power switch is set to ON (I). The system will enter standby mode.

Initial Setup After you have connected the display to the power, you are ready to power on the display. The first time you power on the display, you will be guided through a series of setup screens. Follow the on-screen instructions or the steps below to start up your display and complete the initial setup. 1. Turn on the display. Wait for the display to boot up with the BenQ screen. This may

take a moment. 2. Tap Next on the screen to begin. Follow the on-screen instructions to set up the

language, date and time, and network. Or your can skip some of these steps and complete the setup later.

To turn on the display, press the POWER button on the control panel or on the remote control.

To turn off the display, press the POWER button on the control panel or on the remote control. The system will automatically enter standby mode.

Power Button

IR Receiver

The displays standby mode still consumes power. To completely cut off power supply, set the power switch to OFF (O) and then disconnect the power cord from the power outlet.

Basic operations26

Sidebar Menu To access the sidebar menu:

1. Press the MENU ( ) button on the control panel, or swipe in from the right edge of the screen. The sidebar menu appears at the right side of the screen.

2. Tap the option/function that you want to use.

Options Name/Icon Description

Input Source ( ) Selects an input signal. Refer to Switching input signals on page 27 for more information.

Display Settings ( ) Opens or closes the OSD menu.

Back ( ) Returns to the previous screen or exit the running application.

Home ( ) Returns to the Android home screen.

Recent apps ( ) Displays a list of the most recently used apps.

Tools ( ) Reveals additional tools, including Volume, Screen Capture, and Whiteboard functions.

Freeze ( ) Freezes the screen, tap again to unfreeze screen.

Blank ( ) Hides the image (the screen becomes blank), tap again to resume normal display.

Basic operations 27

Switching input signals To select an input signal: Press the INPUT button on the remote control, and press the or button to select an input signal.

Tap the Input Source ( ) icon in the sidebar menu, and then tap an input signal.

Basic operations28

Eye Care solutions Blue light with wavelengths under 455 nm could affect vision and age the eyes. Eye Care solution is designed for eyesight protection: the display provides proprietary eye-care technology with zero-flicker performance and ultra-low blue light emission, preventing eyestrain, eye fatigue and macular degeneration caused by extended sessions in front of a display. In addition, advanced anti-glare screen treatment minimizes distracting reflections and glare for optimal productivity and comfort.

Downloading software BenQ may periodically release software updates that may add functions or applications associated with your display. To check if there is a software update available for your device or to obtain the software license key, please visit http://business-display.benq.com/ en/findproduct/ifp/software.html. Then enter the serial number (can be found on the sticker attached on the back of the display) and click Ok to access the Software download page.

Setting up Internet connection Your display must be connected to a network to download updates or surf the Internet.

Wired Connection 1. Connect one end of the Ethernet cable to the LAN port of the display. 2. Connect the other end of the Ethernet cable to the LAN port of the router.

3. Press the HOME ( ) button on the remote control, or tap the Home ( ) icon in the sidebar menu to open the Android home screen.

4. On the home screen, select Settings ( ) > Wireless & networks ( ) > Ethernet configuration to view the internet settings.

Wireless Connection Please contact your local dealer for more information on configuring the wireless connection.

1. Press the HOME ( ) button on the remote control, or tap the Home ( ) icon in the sidebar menu to open the Android home screen.

2. On the home screen, select Settings ( ) > Wireless & networks ( ) > Wi- Fi > On/Off to turn Wi-Fi on.

Suggestions for long-term use of the display: Rest your eyes for 10 minutes after 30 minutes of continuous use. For every 20 minutes of display viewing, look into the distance for 20 seconds. When your eyes get sore and strained, close your eyes for a minute and then roll your eyes in

all directions.

Basic operations 29

3. A list of available networks is displayed. Tap the network you want to connect to and tap Connect.

Updating software Whenever a new version of software is available, the system will automatically detect the update and will prompt you to download it every time you turn on the display.

There are two methods that can be used to update the software: If you want to update the software via the internet, select NETWORK UPDATE and then press the OK button on the remote control.

If you want to update the software via the USB port, select USB UPDATE then press the OK button on the remote control.

Or you can skip this step and update the software later.

If you are connecting to a secured wireless network, enter the password for the wireless network access when prompted and tap Connect.

For wireless connection, BenQ shipment does not include wireless dongles, therefore, you may purchase it separately via the local dealer.

Software update process may take some time to complete. During the update process, do not turn off the device or disconnect the Internet connection.

Any interruptions during the software update process may permanently damage your display.

Basic operations30

Restoring to the default settings If you encounter problems with your display, you can restore all parameters to the factory default settings.

There are two methods that can be used to reset your display. Via OSD menu

1. Press the MENU button on the remote control, or tap the Display Settings ( ) icon in the sidebar menu to open the OSD menu.

2. Press the or button on the remote control (or swipe left or right along the top of the OSD menu on the screen) to select the Setting menu.

3. In the Setting menu, press the or button on the remote control (or scroll down on the screen) to select Restore To Default.

4. A confirmation appears on the screen, select Yes to reset your display.

Via Android OS

1. Press the HOME ( ) button on the remote control, or tap the Home ( ) icon in the sidebar menu to open the Android home screen.

2. On the home screen, select Settings ( ) > Personal > Reset. 3. In the Reset menu, select Factory data reset. 4. In the Factory data reset menu, select Reset device > Erase everything.

Adjusting audio volume level Press VOL- / VOL+ on the remote control, or tap Tools ( ) > Volume ( ) in the sidebar Menu to adjust the volume.

Before performing a factory reset, make sure to back up your important data and files.

The OSD (On-Screen Display) menu 31

The OSD (On-Screen Display) menu OSD menu overview

Menu name Options/functions See page

Picture

Picture Mode Contrast Brightness Hue Sharpness Saturation Back Light PC Image Mode Color Temperature Zoom Mode

33

Sound

Sound Mode Low Pitch High Pitch Balance

34

Setting

Menu Time Anti Image Retention HDMI_CEC HDMI EDID Version Light Sensor Keypad Lock IR Lock Power On Mode Power Save Boot Source Software Update(USB) Restore To Default

35

Some options are only available when a certain input signal source is selected.

The OSD (On-Screen Display) menu32

Operations in the OSD menu

Using the touch screen Using the remote control

1. Swipe in from the right edge of the screen to reveal the sidebar menu, and

tap Display Settings ( ) to open the OSD menu.

1. Press the MENU button to open the OSD menu.

2. Swipe left or right along the top of the OSD menu on the screen to select the submenu.

2. Press the or button to select an item.

3. Scroll up or down to browse the items. 3. Press the OK button to confirm

selections.

4. Tap an option to adjust and save the settings.

4. Press the and button to select a feature and press the or button to adjust settings. Press the OK button to confirm changes.

The OSD (On-Screen Display) menu 33

Picture menu Screen images and icons in this document are for your reference only. Actual displays may vary.

Name Description

Picture Mode

Sets the display mode. Available modes are PC, Lightness, Standard, Eyecare, and User. The properties such as Contrast, Brightness, Hue, Sharpness, Saturation, and PC Image Mode can be adjusted if the mode is set to User.

If the mode is set to Eyecare, low blue light will be activated.

Contrast Adjusts the degree of difference between darkness and lightness. Brightness Adjusts the balance between light and dark shades. Hue Adjusts the degree of how we perceive colors. Sharpness Adjusts the clarity and visibility of the edges of the subjects in the image. Saturation Adjusts the purity degree of colors. Back Light Adjusts the back light darkness and lightness.

PC Image Mode

Adjusts the PC display settings. Sets PC image mode to Auto Tune to synchronize the display automatically, or manually fine-tunes Clock, Phase, Horizontal Position, and Vertical Position.

Color Temperature

Adjusts the color temperature. Available options are Cold, Nature, and Warm.

The OSD (On-Screen Display) menu34

Sound menu Screen images and icons in this document are for your reference only. Actual displays may vary.

Zoom Mode

Sets the aspect ratio of the displayed image. The supported aspect ratio varies depending on the input source: HDMI: Auto, Panorama Mode, Just Scan, 14:9, PC Mode, Default, 16:9, and 4:3.

VGA: 16:9, 4:3, 14:9, PC Mode, and Default.

Name Description

Sound Mode Selects a preset audio mode. Available modes are Standard, Music, Movie, Sports, and User. The properties such as Low Pitch and High Pitch can be adjusted if the mode is set to User.

Low Pitch Adjusts the bass level. High Pitch Adjusts the treble level. Balance Adjusts the sound balance between the left and right speakers.

The OSD (On-Screen Display) menu 35

Setting menu Screen images and icons in this document are for your reference only. Actual displays may vary.

Software Update(USB)

Name Description

Menu Time Adjusts the display time of the OSD menu. Available options are 5 Seconds, 10 Seconds, 15 Seconds, 20 Seconds, 30 Seconds, or Always.

Anti Image Retention Enables/disables the image retention function.

HDMI_CEC Allows the user to command and control the CEC-enabled devices connected through HDMI by using only one remote control.

HDMI EDID Version

Adjusts the output signals image resolution to match the displays native resolution. Available options are Default, EDID 1.4, or EDID 2.0.

Light Sensor Enables/disables the ambient light sensor. Keypad Lock Enables/disables the buttons on the control panel. IR Lock Enables/disables the input from the remote control.

The OSD (On-Screen Display) menu36

Power On Mode

Sets the display to a specific power mode once the main power has been re-supplied after a shut-down (for example a power outage). Available options are Power Off, Last Status, or Force On.

If the mode is set to Power Off, you need to press the POWER button on the control panel or on the remote control to turn the display on.

Power Save

Sets the display to reduce power consumption automatically. Available options are Low, High, or Off. Low: If the display receives no signal or any operations for 5 minutes, the screen becomes blank until a signal is detected from the input source.

High: If the display receives no signal or any operations for 5 minutes, it automatically goes into stand-by mode.

Off: The display always keeps in power-on mode.

Boot Source Sets the video source after a reboot. Available options are Last Input, VGA, OPS, HDMI 1, HDMI 2, HDMI 3, HDMI 4, and Android.

Software Update(USB) Updates to a new version of the system software.

Restore To Default Restores all parameters to the factory default settings.

Working with Android OS 37

Working with Android OS To switch to the Android OS:

1. Press the MENU ( ) button on the control panel, or swipe in from the right edge of the screen. The sidebar menu appears at the right side of the screen.

2. Tap the Home ( ) icon in the sidebar menu to open the Android home screen.

3. Select the application that you want to access. Using the touch pen or your finger: Tap your desired application icon to launch the

application. Using the remote control: Press the 3 or 4 button to select your desired application

and press the OK button to launch the application.

Select Local Application ( ) to access all applications.

To return to the Android home screen, press the HOME ( ) button on the remote control,

or tap Home ( ) icon in the sidebar menu. Since the system does not support any third party applications, users may be unable to open an

application even if the installation has completed successfully.

Working with Android OS38

Settings Tap to launch Settings. With this application, you can view and configure the settings for your device.

Tap the desired menu option to enter its submenu.

Menu Option Description

Wireless & networks Select Wi-Fi or Ethernet to view the network status or configure the network connection.

Device Select Storage to view the system storage information. Select Apps to view downloaded apps, system apps, and running apps.

Personal Select Language & input to change the system language and input.

Select Reset to restore all parameters to the factory default settings.

Select Power Option to set up the time of sleep and power off.

System Select Date & time to set the date and time. Select About device to update software or view the basic system information (i.e. device name, legal information, model name, software version, serial number, and build information).

Working with Android OS 39

Local Application Tap to launch Local Application. This menu allows you to view all the applications installed in your device.

Tap the desired app to launch the app.

Application Name/Icon Description

BenQ Suggest ( ) Shows the Android apps suggested by BenQ. Refer to BenQ Suggest on page 40 for more information.

Browser ( ) Accesses web pages. Refer to Browser on page 41 for more information.

ES File Explorer ( ) Manages files stored on the displays internal memory and connected storage devices. Refer to ES File Explorer on page 42 for more information.

EZWrite 4.1 Lite ( ) Draws on the screen or annotates. Refer to EZWrite 4.1 Lite Documents for more information.

InstaQPrint ( )

Prints files stored on the displays internal memory and connected storage devices, or any images shown on the display. Refer to InstaQPrint on page 43 for more information.

InstaShare ( ) Shares files stored on the displays internal memory and connected storage devices. Refer to InstaShare on page 44 for more information.

Multimedia ( ) Browses the multimedia files stored on the displays internal memory or connected storage devices. Refer to Multimedia on page 46 for more information.

WPS Office ( ) Reads and edits files in Office formats, including, *.doc, *.txt, *.xls, *.pdf, and *.ppt. Refer to WPS Office on page 47 for more information.

Working with Android OS40

BenQ Suggest Tap to launch BenQ Suggest. With this application, you can view apps suggested by BenQ for download.

Tap the category on the left panel to browse the suggested apps. Tap an app from the selected category to view a basic description of the app.

Function Description

Search ( ) Tap to search for an app.

Education ( ) Tap to show the suggested apps in the Education category.

Corporation ( ) Tap to show the suggested apps in the Corporation category.

Working with Android OS 41

Browser Tap to launch Browser. With this application, you can view web pages.

Tap the icon on the top panel to activate its function. Slide on the screen to scroll the viewed page.

Before launching the application, make sure your display is properly connected to lnternet.

Function Description

Address Bar Enter the web page address to view the page.

Close ( ) Tap to close the current web page.

New ( ) Tap to open a new web page.

Settings ( ) Tap to configure the browser settings.

Back ( ) Tap to return to the previous page.

Next ( ) Tap to go to the next page.

Refresh ( ) Tap to reload the current web page.

Favorite ( ) Tap to save the current web page to bookmarks.

Search ( ) Tap to search the Internet.

Bookmarks ( ) Tap to select bookmarks, history, or saved favorite web pages to visit.

Working with Android OS42

ES File Explorer Tap to launch ES File Explorer. With this application, you can manage the files and apps.

Tap the category on the left panel and select the desired folder to browse. Tap a file in the folder, then you can view or edit the file according to the available options.

Function Description

Exit ( ) Tap to close ES File Explorer. Theme ( ) Tap to change different theme.

Settings ( ) Tap to access more advanced options.

New ( ) Tap to create a new folder.

Search ( ) Tap to search for files in the internal memory or external device.

Refresh ( ) Tap to reload the current page.

View ( ) Tap to toggle between list view or icons view.

Windows ( )

Tap to switch between open windows.

Working with Android OS 43

InstaQPrint Tap to launch InstaQPrint. With this application, you can print a file or website

image using a Wi-Fi or remote printer.

1. Tap the option on the left panel and browse and select the desired file, photo, page, or image you want to print.

2. Tap Manage Printers to choose which printer that you want to use. 3. To select a printer:

Tap an option from the list of available printers on the left panel. Tap Scan for Wi-Fi Printers to search for printers automatically. Tap Manual Setup to add a new printer manually.

Before launching the application, make sure your display is properly connected to lnternet. For the list of supported printers, see https://printhand.com/list_of_supported_printers.php.

Working with Android OS44

InstaShare Tap to launch InstaShare. With this application, you can mirror the display's screen on your smartphone or tablet for hands-on annotation and mirror the screen of your smartphone or tablet on the display.

To use InstaShare: 1. Make sure your mobile device (such as smartphone or tablet) and the display are

connected to the same network. 2. Press the connection guide and scan the QR code to download and install the

InstaShare app on your mobile device. 3. Open the InstaShare app on your mobile device, and then click the InstaShare

ID name that you want to connect to or enter the pairing code. 4. Enter the connect code shown on the upper right corner of the display or you can

also find the connection code in Setting ( ). 5. Once the mobile device has successfully connected to the display, a confirmation

message will appear on the display. Tap Allow on the display to confirm the connection.

6. Once connected you can: Mirror the display's screen on your mobile device by tapping Screen Mirroring on

your mobile device.

Mirror the devices screen on the display by tapping on your mobile device.

Operate the display by using your mobile device as a remote control.

Before launching the application, make sure your display is properly connected to lnternet.

Once connected, any operations on the display or mobile device will also show up on your mobile device and display.

Working with Android OS 45

You can also tap Setting ( ) in the lower right corner of the display to modify the settings for InstaShare, such as the InstaShare ID name, connect code, or mirroring confirmation message.

Working with Android OS46

Multimedia Tap to launch Multimedia. With this application, you can browse the photos, songs, or videos stored on the internal memory or connected storage devices.

Tap All to view the all files. Tap Picture to view the photos. Tap the desired photo to view it in full screen. Tap Music to view the audio files. Tap the desired audio file to play the song/audio clip. Tap Video to view the videos. Tap the desired video file to play the video clip.

Supported multimedia file formats Video

Photo

Audio

Supported File Formats File Extension

MPEG1 / MPEG2 / MPEG4 / H264 / RM / RMVB / MOV / MJPEG / VC1 / DIVX / FLV

.avi / .mpg / .dat / .vob / .div / .mov / .mkv / .rm / .rmvb /

.mp4 / .mjpeg / .ts / .trp / .wmv / .asf / .flv

Supported File Formats File Extension

JPEG / BMP / PNG .jpg / .bmp / .png

Supported File Formats File Extension

WMA / MP3/ M4A (AAC) .wma / .mp3 / .m4a

Working with Android OS 47

WPS Office Tap to launch WPS Office. With this application, you can open document files including PDFs as well as Microsoft Word, PowerPoint and Excel documents.

To edit a file with WPS Office:

1. Tap Open ( ) on the left panel to browse and open a file located in either the dis- plays internal memory, an external storage device, or cloud storage.

2. Tap the function menu on the top panel to access the file format's various functions.

The description below is for a PowerPoint file, the function menus for other file formats will vary.

Function Description

File Tap to open, save, share, print, and manage your presentations. View Tap to change or edit the presentation views.

Working with Android OS48

Supported Office versions and file formats Supported Office versions: 97 / 2000 / XP/ 2003 / 2007 / 2010

Supported Office software formats:

Play Tap to start or set up a slide show. Edit Tap to edit the content or format of the slides. Insert Tap to insert tables, pictures, charts, comments, video, or audio. Transitions Tap to apply or adjust the timing of a transition. Pen Tap to write, draw, paint or sketch to the slides.

Play ( ) Tap to start a slide show.

Save As ( ) Tap to save the presentation file on either the displays internal memory, an external storage device, or cloud storage.

Undo ( ) Tap to undo an action.

Redo ( ) Tap to redo the last action.

Close ( ) Tap to close the presentation file.

Back ( ) Tap to return to the previous page.

Next ( ) Tap to go to the next page.

Exit ( ) Tap to exit WPS Office.

Office Software Supported File Formats

Word wps / wpt / doc / docx / dot / dotx / txt / log / irc / c / cpp / h / asm / s / java / asp / bat / bas / prg / cmd

Excel et / ett / xls / xlsx / xlt / xltx / csv / xlsm / xltm PowerPoint ppt / pptx

Product information 49

Product information Specifications

Item Specifications

RM7501K RM8601K

LCD panel

Backlight DLED DLED Panel size 75 86 Pixel pitch (mm) 0.43 (H) x 0.43 (V) 0.49 (H) x 0.49 (V) Native resolution (pixels) UHD 3840 x 2160 UHD 3840 x 2160

Brightness (cd/m2) (typical) 350 400

Contrast (typical) 1200:1 Response time (ms) (typical) 8

Panel Bit 10 bit 10 bit

Touch

Technology IR Touch Resolution 32767 x 32767

Capacity 20 points (Varies from operating systems and applications)

Accuracy 1mm over 90% of touchable area Touch Output x1 (USB Type B)

Operating System Win 7, Win 8/8.1, Win 10 / Mac OS X10.11~10.12 /

Chrome OS 58 / Ubuntu 16.04 / Fedora 28 / OpenSuse 15 / Android kernel version 3.10 or above

Panel glass

Tempered glass (thickness, Mohs scale)

4mm, 7H

Anti bacteria coating X AG80 O

Input

Computer VGA (D-Sub 15-pin), HDMI 2.0 x4 Video HDMI 2.0 x4 (HDMI 2.0 MHL x1, share with HDMI) Audio Mic-in (3.5 mm Jack) USB Type-A x4 (2.0 x 2; 3.0 x 2), Type-B x1 Control RS-232 (D-Sub 9-pin)

OPS Option Slot Open pluggable specification (Intel OPS standard) x 1 (19V/4.5A)

Output

Computer HDMI 2.0 Video HDMI 2.0 Audio PC-audio (3.5 mm jack) Control RS-232 (D-Sub 9-pin)

Audio Audio W (Amp) 20W x 2 Internal speaker O

Product information50

Power

Supply 100 - 240V AC, 50/60 Hz, 5.0A

100 - 240V AC, 50/60 Hz, 5.5A

Consumption Max. 460W 500W Consumption Standby 0.5W

Environment

Operating Temperature 0oC - 40oC

Operating Humidity 20% ~ 80% RH Non- Condensing

20% ~ 80% RH Non- Condensing

Storage Temperature -10oC - 60oC

Storage Humidity 10% ~ 60% RH Non- Condensing

10% ~ 60% RH Non- Condensing

Display Orientation Landscape

Mechanical

Weight (without packing / with packing)

65.0kg / 76.2kg 1.5Kg 90.4kg / 103.2kg 1.5Kg

Dimensions (W x H x D) (mm) 1736.8 x1085.3 x137.1 1990 x1231 x140.9

Bezel Dimension - T/B/L/R (mm) 28 / 98 / 28 / 28

Feature

DVI daisy chain X X RS232 control daisy chain X X

Image setting O O Picture mode O O Sharpness enhancement O O

Proof of image retention O O

Dimming control X X Blank O O Freeze O O 10-bit color processing O O

Built-in video wall support X X

Scheduling X X Source / volume control O O

HDMI-HDCP O O HDMI-MHL O O De-Interlacing / Comb Filter X X

Ambient light sensor O O

Product information 51

Specifications and functions are subject to change without notice. To make sure that the touch function works properly on Mac OS X 10.10, you are

recommended to perform screen calibration first. Contact BenQ dealer for the required calibration utility.

Item RM7501K RM8601K

System

CPU ARM Cortex A53 1.4GHz, Quad Core (MSD6A828) System Memory 2GB Storage 32GB OS Android 5.0.1

OS: This Android 5.0 operating system is not standard Android, so access to Google Play is not available. APK cannot be installed in the default location unless given permission by the management units. Contact your BenQ dealer for the required support for the management permission. Without management permission, installing function wont work. There is no guarantee that the self-installed APK can function normally.

Storage: Content storage may vary by the product supplied for your region. Pre-installed system and apps may take up some space.

Product information52

Dimensions RM7501K

Unit: mm

1736,8

1085,3

3092,1

137,1

25,4 600

568,4 568,4

400 297,7387,6

26,326,3

26,3

26,3

Product information 53

RM8601K

Unit: mm

Product information54

Supported input signal resolution

RM7501K & RM8601K

Resolution

Input source

HDMI 1/ HDMI 2/ HDMI 3/

OPS

HDMI 4 VGA

640 x 350 @ 85Hz

640 x 480 @ 85Hz

640 x 480 @ 60Hz

720 x 400 @ 85Hz

720 x 400 @ 70Hz

720 x 576 @ 60Hz

800 x 600 @ 85Hz

800 x 600 @ 60Hz

1024 x 768 @ 85Hz

1024 x 768 @ 60Hz

1152 x 864 @ 75Hz

1280 x 720 @ 120Hz

1280 x 720 @ 60Hz

1280 x 800 @ 60Hz

1280 x 960 @ 60Hz

1280 x 1024 @ 85Hz

1360 x 768 @ 60Hz

1366 x 768 @ 60Hz

1600 x 900 @ 60Hz

1600 x 1200 @ 60Hz

1920 x 1080 @ 60Hz

3840 x 2160 @ 30Hz

3840 x 2160 @ 60Hz

: supported Blank: not supported

Troubleshooting 55

Troubleshooting Problem Solution

No picture

Check the following: Is the display turned on? Check the power indicator of the display.

Is the signal source device turned on? Turn on the device and try again.

Are there any loose cable connections? Make sure that all cables are connected firmly.

Have you chosen an unsupported output resolution on the computer? Refer to Supported input on page 54 to select a supported resolution and try again.

Have you chosen an unsupported output resolution on the DVD or Blu-ray disc player? Refer to Supported input on page 54 to select a supported resolution and try again.

No sound

Check the following: Have you turned on the mute function on the display or the input source device? Turn off the mute function or increase the audio volume level and try again.

Are there any loose cable connections? Make sure that all cables are connected firmly.

The computer input image looks strange

Have you chosen an unsupported output resolution on the computer? Refer to Supported input on page 54 to select a supported resolution and try again.

Use the Auto Tune function (See Picture menu on page 33) to let the display automatically optimize the display of computer image.

If the result of the Auto Tune function is not satisfactory, use the Clock, Phase, Horizontal Position, and Vertical Position functions to manually adjust the image.

The displayed image looks blurry or grainy

Use the Default function (See Setting menu on page 35) to set the output signals image resolution match to the displays native resolution.

If the result of the Default function is not satisfactory, use the EDID 1.4 or EDID 2.0 functions to manually adjust the resolution.

The control panel buttons do not work

Have you locked the control panel buttons? Refer to the Keypad Lock function (See Setting menu on page 35) to unlock the buttons and try again.

Troubleshooting56

The remote control does not work

Check for incorrect battery orientation. Check for dead batteries. Check your distance and angle from the display. Check whether remote control is properly being pointed at the displays remote control sensor window.

Check for any obstacle between the remote control and the remote control sensor window.

Check that the remote control sensor window is not under strong fluorescent lighting, or in direct sunlight.

Check for any devices (computer or personal digital assistant, PDA) nearby that transmit infrared signals which may cause interference to signal transmission between the remote control and the display. Turn off the infrared function of these devices.

USB Function When working with the environment of ESD interference, it is normal that the USB c

Manualsnet FAQs

If you want to find out how the RM7501K BenQ works, you can view and download the BenQ RM7501K User Manual on the Manualsnet website.

Yes, we have the User Manual for BenQ RM7501K as well as other BenQ manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a BenQ RM7501K. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the BenQ RM7501K User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This BenQ RM7501K User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download BenQ RM7501K User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print BenQ RM7501K User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the BenQ RM7501K User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.