Behringer FEX800 Quick Start Guide PDF

1 of 15
1 of 15

Summary of Content for Behringer FEX800 Quick Start Guide PDF

Quick Start Guide (Check out behringer.com for Full Manual)

MINIFEX FEX800 Ultra-Compact Stereo Multi-FX Processor

LEGAL DISCLAIMER

LIMITED WARRANTYImportant Safety Instructions

Terminals marked with this symbol carry electrical current of suffi cient

magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with " TS or twist- locking plugs pre-installed. All other installation or modifi cation should be performed only by qualifi ed personnel.

This symbol, wherever it appears, alerts you to the presence of uninsulated

dangerous voltage inside the enclosure - voltage that may be suffi cient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and

maintenance instructions in the accompanying literature. Please read the manual.

Caution To reduce the risk of electric shock, do not remove the

top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualifi ed personnel.

Caution To reduce the risk of fi re or electric shock, do not expose

this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects fi lled with liquids, such as vases, shall be placed on the apparatus.

Caution These service instructions are for use by qualifi ed

service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualifi ed service personnel.

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding- type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Use only attachments/accessories specifi ed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with

the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection. 16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

TECHNICAL SPECIFICATIONS AND APPEARANCES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ACCURACY IS NOT GUARANTEED. BEHRINGER, KLARK TEKNIK, MIDAS, BUGERA, AND TURBOSOUND ARE PART OF THE MUSIC GROUP (MUSIC-GROUP.COM). ALL TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED BY ANY PERSON WHO RELIES EITHER WHOLLY OR IN PART UPON ANY DESCRIPTION, PHOTOGRAPH OR STATEMENT CONTAINED HEREIN. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. MUSIC GROUP PRODUCTS ARE SOLD THROUGH AUTHORIZED FULLFILLERS AND RESELLERS ONLY. FULLFILLERS AND RESELLERS ARE NOT AGENTS OF MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED UNDERTAKING OR REPRESENTATION. THIS MANUAL IS COPYRIGHTED. NO PART OF THIS MANUAL MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING AND RECORDING OF ANY KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS WRITTEN PERMISSION OF MUSIC GROUP IP LTD.

ALL RIGHTS RESERVED. 2013 MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, British Virgin Islands

For the applicable warranty terms and conditions and additional information regarding MUSIC Groups Limited Warranty, please see complete details online at www.music-group.com/warranty.

Las terminales marcadas con este smbolo transportan corriente elctrica de

magnitud sufi ciente como para constituir un riesgo de descarga elctrica. Utilice solo cables de altavoz profesionales y de alta calidad con conectores TS de 6,3 mm o de bayoneta prefi jados. Cualquier otra instalacin o modifi cacin debe ser realizada nicamente por un tcnico cualifi cado.

Este smbolo, siempre que aparece, le advierte de la presencia de voltaje

peligroso sin aislar dentro de la caja; este voltaje puede ser sufi ciente para constituir un riesgo de descarga.

Este smbolo, siempre que aparece, le advierte sobre instrucciones operativas y

de mantenimiento que aparecen en la documentacin adjunta. Por favor, lea el manual.

Atencin Para reducir el riesgo de descarga elctrica, no quite

la tapa (o la parte posterior). No hay piezas en el interior del equipo que puedan ser reparadas por el usuario. Si es necesario, pngase en contacto con personal cualifi cado.

Atencin Para reducir el riesgo de incendio o descarga

elctrica, no exponga este aparato a la lluvia, humedad o alguna otra fuente que

pueda salpicar o derramar algn lquido sobre el aparato. No coloque ningn tipo de recipiente para lquidos sobre el aparato.

Atencin Las instrucciones de servicio deben llevarlas a cabo

exclusivamente personal cualifi cado. Para evitar el riesgo de una descarga elctrica, no realice reparaciones que no se encuentren descritas en el manual de operaciones. Las reparaciones deben ser realizadas exclusivamente por personal cualifi cado. 1. Lea las instrucciones. 2. Conserve estas instrucciones. 3. Preste atencin a todas las advertencias. 4. Siga todas las instrucciones. 5. No use este aparato cerca del agua. 6. Limpie este aparato con un pao seco. 7. No bloquee las aberturas de ventilacin. Instale el equipo de acuerdo con las instrucciones del fabricante. 8. No instale este equipo cerca de fuentes de calor tales como radiadores, acumuladores de calor, estufas u otros aparatos (incluyendo amplifi cadores) que puedan producir calor. 9. No elimine o deshabilite nunca la conexin a tierra del aparato o del cable de alimentacin de corriente. Un enchufe polarizado tiene dos polos, uno de los cuales tiene un contacto ms ancho que el otro. Una clavija con puesta a tierra dispone de tres contactos: dos polos y la puesta a tierra. El contacto ancho y el tercer contacto, respectivamente, son los que garantizan una mayor seguridad. Si el enchufe suministrado con el equipo no concuerda con la toma de corriente, consulte con un electricista para cambiar la toma de corriente obsoleta. 10. Coloque el cable de suministro de energa de manera que no pueda ser pisado y que est protegido de objetos afi lados. Asegrese de que el cable de suministro de energa est protegido, especialmente en la zona de la clavija y en el punto donde sale del aparato.

11. Use nicamente los dispositivos o accesorios especifi cados por el fabricante.

12. Use nicamente la carretilla, plataforma, trpode, soporte o mesa especifi cados por

el fabricante o suministrados junto con el equipo. Al transportar el equipo, tenga cuidado para evitar daos y cadas al tropezar con algn obstculo. 13. Desenchufe el equipo durante tormentas o si no va a utilizarlo durante un periodo largo. 14. Confe las reparaciones nicamente a servicios tcnicos cualifi cados. La unidad requiere mantenimiento siempre que haya sufrido algn dao, si el cable de suministro de energa o el enchufe presentaran daos, se hubiera derramado un lquido o hubieran cado objetos dentro del equipo, si el aparato hubiera estado expuesto a la humedad o la lluvia, si ha dejado de funcionar de manera normal o si ha sufrido algn golpe o cada. 15. Al conectar la unidad a la toma de corriente elctrica asegrese de que la conexin disponga de una unin a tierra. 16. Si el enchufe o conector de red sirve como nico medio de desconexin, ste debe ser accesible fcilmente.

LAS ESPECIFICACIONES TCNICAS Y LA APARIENCIA EXTERIOR ESTN SUJETAS A CAMBIOS SIN PREVIO AVISO Y NO PODEMOS GARANTIZAR LA TOTAL EXACTITUD DE TODO LO QUE APARECE AQU. BEHRINGER, KLARK TEKNIK, MIDAS, BUGERA, Y TURBOSOUND SON PARTE DEL GRUPO MUSIC GROUP (MUSIC-GROUP.COM). TODAS LAS MARCAS REGISTRADAS SON PROPIEDAD DE SUS RESPECTIVOS DUEOS. MUSIC GROUP NO ACEPTA NINGN TIPO DE RESPONSABILIDAD POR POSIBLES

Instrucciones de seguridad

NEGACIN LEGAL

2 3Quick Start GuideMINIFEX FEX800

DAOS Y PERJUICIOS SUFRIDOS POR CUALQUIER PERSONA QUE SE HAYA BASADO COMPLETAMENTE O EN PARTE EN LAS DESCRIPCIONES, FOTOGRAFAS O EXPLICACIONES QUE APARECEN EN ESTE DOCUMENTO. LOS COLORES Y ESPECIFICACIONES TCNICAS PUEDEN VARIAR LIGERAMENTE DE UN PRODUCTO A OTRO. LOS PRODUCTOS MUSIC GROUP SON COMERCIALIZADOS NICAMENTE A TRAVS DE DISTRIBUIDORES OFICIALES. LOS DISTRIBUIDORES Y MAYORISTAS NO SON AGENTES DE MUSIC GROUP, POR LO QUE NO ESTN AUTORIZADOS A CONCEDER NINGN TIPO DE CONTRATO O GARANTA QUE OBLIGUE A MUSIC GROUP DE FORMA EXPRESA O IMPLCITA. ESTE MANUAL EST PROTEGIDO POR LAS LEYES DEL COPYRIGHT. ESTE MANUAL NO PUEDE SER REPRODUCIDO O TRANSMITIDO, NI COMPLETO NI EN PARTE, POR NINGN TIPO DE MEDIO, TANTO SI ES ELECTRNICO COMO MECNICO, INCLUYENDO EL FOTOCOPIADO O REGISTRO DE CUALQUIER TIPO Y PARA CUALQUIER FIN, SIN LA AUTORIZACIN EXPRESA Y POR ESCRITO DE MUSIC GROUP IP LTD.

RESERVADOS TODOS LOS DERECHOS. 2013 MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, British Virgin Islands

Si quiere conocer los detalles y condiciones aplicables de la garanta as como informacin adicional sobre la Garanta limitada de MUSIC group, consulte online toda la informacin en la web www.music-group.com/warranty.

Les points reprs par ce symbole portent une tension lectrique suffi sante

pour constituer un risque dlectrocution.

Utilisez uniquement des cbles denceintes professionnels de haute qualit avec fi ches Jack mono 6,35 mm ou fi ches verrouillages dj installes. Toute autre installation ou modifi cation doit tre eff ectue uniquement par un personnel qualifi .

Ce symbole avertit de la prsence dune tension dangereuse et non isole

lintrieur de lappareil - elle peut provoquer des chocs lectriques.

Attention Ce symbol signale les consignes dutilisation

et dentre ! Tien importantes dans la documentation fournie. Lisez les consignes de scurit du manuel dutilisation de lappareil.

Attention Pour viter tout risque de choc lectrique, ne pas

ouvrir le capot de lappareil ni dmonter le panneau arrire. Lintrieur de lappareil ne possde aucun lment rparable par lutilisateur. Laisser toute rparation un professionnel qualifi .

Attention Pour rduire les risques de feu et de choc lectrique,

nexposez pas cet appareil la pluie, la moisissure, aux gouttes ou aux claboussures. Ne posez pas de rcipient contenant un liquide sur lappareil (un vase par exemple).

Attention Ces consignes de scurit et dentretien sont destines

un personnel qualifi . Pour viter tout risque de choc lectrique, neff ectuez aucune rparation sur lappareil qui ne soit dcrite par le manuel dutilisation. Les ventuelles rparations doivent tre eff ectues uniquement par un technicien spcialis. 1. Lisez ces consignes. 2. Conservez ces consignes. 3. Respectez tous les avertissements. 4. Respectez toutes les consignes dutilisation. 5. Nutilisez jamais lappareil proximit dun liquide.

6. Nettoyez lappareil avec un chiff on sec. 7. Veillez ne pas empcher la bonne ventilation de lappareil via ses oues de ventilation. Respectez les consignes du fabricant concernant linstallation de lappareil. 8. Ne placez pas lappareil proximit dune source de chaleur telle quun chauff age, une cuisinire ou tout appareil dgageant de la chaleur (y compris un ampli de puissance). 9. Ne supprimez jamais la scurit des prises bipolaires ou des prises terre. Les prises bipolaires possdent deux contacts de largeur diff rente. Le plus large est le contact de scurit. Les prises terre possdent deux contacts plus une mise la terre servant de scurit. Si la prise du bloc dalimentation ou du cordon dali-mentation fourni ne correspond pas celles de votre installation lectrique, faites appel un lectricien pour eff ectuer le changement de prise. 10. Installez le cordon dalimentation de telle faon que personne ne puisse marcher dessus et quil soit protg dartes coupantes. Assurez-vous que le cordon dalimentation est suffisamment protg, notamment au niveau de sa prise lectrique et de lendroit o il est reli lappareil; cela est galement valable pour une ventuelle rallonge lectrique. 11. Utilisez exclusivement des accessoires et des appareils supplmentaires recommands par le fabricant.

12. Utilisez exclusivement des chariots, des diables, des prsentoirs, des pieds et des surfaces

de travail recommands par le fabricant ou livrs avec le produit. Dplacez prcautionneusement tout chariot ou diable charg pour viter dventuelles blessures en cas de chute. 13. Dbranchez lappareil de la tension secteur en cas dorage ou si lappareil reste inutilis pendant une longue priode de temps. 14. Les travaux dentretien de lappareil doivent tre eff ectus uniquement par

du personnel qualifi. Aucun entretien nest ncessaire sauf si lappareil est endommag de quelque faon que ce soit (dommages sur le cordon dalimentation ou la prise par exemple), si un liquide ou un objet a pntr lintrieur du chssis, si lappareil a t expos la pluie ou lhumidit, sil ne fonctionne pas correctement ou la suite dune chute. 15. Lappareil doit tre connect une prise secteur dote dune protection par mise la terre. 16. La prise lectrique ou la prise IEC de tout appareil dnu de bouton marche/ arrt doit rester accessible en permanence.

CARACTRISTIQUES TECHNIQUES ET APPARENCE SUJETTES MODIFICATIONS SANS PRAVIS. PRCISION NON GARANTIE. BEHRINGER, KLARK TEKNIK, MIDAS, BUGERA, ET TURBOSOUND FONT PARTIE DU MUSIC GROUP (MUSIC-GROUP.COM). TOUTES LES MARQUES DPOSES SONT LA PROPRIT DE LEURS PROPRITAIRES RESPECTIFS. LA SOCIT MUSIC GROUP NACCEPTE AUCUNE RESPONSABILIT DANS LES VENTUELS DOMMAGES OU PERTES SUBIS PAR UN TIERS EN SE BASANT EN ENTIER OU EN PARTIE SUR LES DESCRIPTIONS, PHOTOGRAPHIES OU DCLARATIONS CONTENUES DANS CE DOCUMENT. LES COULEURS ET CARACTRISTIQUES PEUVENT VARIER LGREMENT DE CELLES DU PRODUIT. LES PRODUITS MUSIC GROUP NE SONT VENDUS QUE PAR LE BIAIS DE REVENDEURS AGRS. LES DISTRIBUTEURS ET LES REVENDEURS NE SONT PAS AGENTS DE MUSIC GROUP ET NONT ABSOLUMENT AUCUNE AUTORIT POUR ENGAGER OU REPRSENTER LA SOCIT MUSIC GROUP DE FAON IMPLICITE, EXPLICITE OU INDIRECTE. CE MODE DEMPLOI EST PROTG PAR DROITS DAUTEURS. IL EST INTERDIT DE TRANSMETTRE OU DE COPIER CE MODE DEMPLOI SOUS

QUELLE FORME QUE CE SOIT, PAR QUEL MOYEN QUE CE SOIT, LECTRONIQUE OU MCANIQUE, CE QUI COMPREND LES MOYENS DE PHOTOCOPIE ET DENREGISTREMENT DE QUELLE FAON QUE CE SOIT, QUEL QUE SOIT LE BUT, SANS LA PERMISSION CRITE EXPRESSE DE MUSIC GROUP IP LTD.

TOUS DROITS RSERVS. 2013 MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, Iles Vierges Britanniques

Pour connatre les termes et conditions de garantie applicables, ainsi que les informations supplmentaires et dtailles sur la Garantie Limite de MUSIC Group, consultez le site Internet www.music-group.com/warranty.

Vorsicht Die mit dem Symbol markierten Anschlsse

fhren so viel Spannung, dass die Gefahr eines Stromschlags besteht. Verwenden Sie nur hochwertige, professionelle Lautsprecherkabel mit vorinstallierten 6,35 mm MONO-Klinkensteckern oder Lautsprecherstecker mit Drehverriegelung. Alle anderen Installationen oder Modifi kationen sollten nur von qualifi ziertem Fachpersonal ausgefhrt werden.

Achtung Um eine Gefhrdung durch Stromschlag auszuschlieen,

darf die Gerteabdeckung bzw. Gerterckwand nicht abgenommen werden. Im Innern des Gerts befi nden sich keine vom Benutzer reparierbaren Teile. Reparaturarbeiten drfen nur von qualifi ziertem Personal ausgefhrt werden.

Achtung Um eine Gefhrdung durch Feuer bzw. Stromschlag

auszuschlieen, darf dieses Gert weder Regen oder Feuchtigkeit ausgesetzt werden noch sollten Spritzwasser oder tropfende Flssigkeiten in das Gert gelangen knnen. Stellen Sie keine mit Flssigkeit gefllten Gegenstnde, wie z. B. Vasen, auf das Gert.

Achtung Die Service-Hinweise sind nur durch qualifi ziertes

Personal zu befolgen. Um eine Gefhrdung durch Stromschlag zu vermeiden, fhren Sie bitte keinerlei Reparaturen an dem Gert durch, die nicht in der Bedienungsanleitung beschrieben sind. Reparaturen sind nur von qualifi ziertem Fachpersonal durchzufhren. 1. Lesen Sie diese Hinweise. 2. Bewahren Sie diese Hinweise auf. 3. Beachten Sie alle Warnhinweise. 4. Befolgen Sie alle Bedienungshinweise. 5. Betreiben Sie das Gert nicht in der Nhe von Wasser. 6. Reinigen Sie das Gert mit einem trockenen Tuch. 7. Blockieren Sie nicht die Belftungsschlitze. Beachten Sie beim Einbau des Gertes die Herstellerhinweise. 8. Stellen Sie das Gert nicht in der Nhe von Wrmequellen auf. Solche Wrmequellen sind z. B. Heizkrper, Herde oder andere Wrme erzeugende Gerte (auch Verstrker). 9. Entfernen Sie in keinem Fall die Sicherheitsvorrichtung von Zweipol- oder geerdeten Steckern. Ein Zweipolstecker hat zwei unterschiedlich breite Steckkontakte. Ein geerdeter Stecker hat zwei Steckkontakte und einen dritten Erdungskontakt. Der breitere Steckkontakt oder der zustzliche Erdungskontakt dient Ihrer Sicherheit. Falls das mitgelieferte Steckerformat nicht zu Ihrer Steckdose passt, wenden Sie sich bitte an einen Elektriker, damit die Steckdose entsprechend ausgetauscht wird.

GARANTA LIMITADA

Consignes de scurit

DNI LGAL

GARANTIE LIMITE

Wichtige Sicherhteitshinweise

4 5Quick Start GuideMINIFEX FEX800

10. Verlegen Sie das Netzkabel so, dass es vor Tritten und scharfen Kanten geschtzt ist und nicht beschdigt werden kann. Achten Sie bitte insbesondere im Bereich der Stecker, Verlngerungskabel und an der Stelle, an der das Netzkabel das Gert verlsst, auf ausreichenden Schutz. 11. Das Gert muss jederzeit mit intaktem Schutzleiter an das Stromnetz angeschlossen sein. 12. Sollte der Hauptnetzstecker oder eine Gertesteckdose die Funktionseinheit zum Abschalten sein, muss diese immer zugnglich sein. 13. Verwenden Sie nur Zusatzgerte/ Zubehrteile, die laut Hersteller geeignet sind.

14. Verwenden Sie nur Wagen, Standvorrichtungen, Stative, Halter oder Tische, die vom Hersteller benannt

oder im Lieferumfang des Gerts enthalten sind. Falls Sie einen Wagen benutzen, seien Sie vorsichtig beim Bewegen der Wagen-Gertkombination, um Verletzungen durch Stolpern zu vermeiden. 15. Ziehen Sie den Netzstecker bei Gewitter oder wenn Sie das Gert lngere Zeit nicht benutzen. 16. Lassen Sie alle Wartungsarbeiten nur von qualifi ziertem Service-Personal ausfhren. Eine Wartung ist notwendig, wenn das Gert in irgendeiner Weise beschdigt wurde (z. B. Beschdigung des Netzkabels oder Steckers), Gegenstnde oder Flssigkeit in das Gerteinnere gelangt sind, das Gert Regen oder Feuchtigkeit ausgesetzt wurde, das Gert nicht ordnungsgem funktioniert oder auf den Boden gefallen ist.

17. Korrekte Entsorgung dieses Produkts: Dieses Symbol weist darauf hin, das Produkt entsprechend der WEEE Direktive

(2002/96/EC) und der jeweiligen nationalen Gesetze nicht zusammen mit Ihren Haushaltsabfllen zu entsorgen. Dieses Produkt sollte bei einer autorisierten Sammelstelle fr Recycling elektrischer und elektronischer Gerte

(EEE) abgegeben werden. Wegen bedenklicher Substanzen, die generell mit elektrischen und elektronischen Gerten in Verbindung stehen, knnte eine unsachgeme Behandlung dieser Abfallart eine negative Auswirkung auf Umwelt und Gesundheit haben. Gleichzeitig gewhrleistet Ihr Beitrag zur richtigen Entsorgung dieses Produkts die eff ektive Nutzung natrlicher Ressourcen. Fr weitere Informationen zur Entsorgung Ihrer Gerte bei einer Recycling-Stelle nehmen Sie bitte Kontakt zum zustndigen stdtischen Bro, Entsorgungsamt oder zu Ihrem Haushaltsabfallentsorger auf.

TECHNISCHE DATEN UND ERSCHEINUNGSBILD KNNEN UNANGEKNDIGT GENDERT WERDEN. IRRTMER BLEIBEN VORBEHALTEN. BEHRINGER, KLARK TEKNIK, MIDAS, BUGERA UND TURBOSOUND SIND TEIL DER MUSIC GROUP (MUSIC-GROUP.COM). ALLE WARENZEICHEN SIND DAS EIGENTUM IHRER JEWEILIGEN BESITZER. MUSIC GROUP BERNIMMT KEINE HAFTUNG FR VERLUSTE, DIE PERSONEN ENTSTEHEN, DIE SICH GANZ ODER TEILWEISE AUF HIER ENTHALTENE BESCHREIBUNGEN, FOTOS ODER AUSSAGEN VERLASSEN. ABGEBILDETE FARBEN UND SPEZIFIKATIONEN KNNEN GERINGFGIG VOM PRODUKT ABWEICHEN. MUSIC GROUP PRODUKTE WERDEN NUR BER AUTORISIERTE FACHHNDLER VERKAUFT. DIE VERTRIEBSPARTNER UND HNDLER SIND KEINE VERTRETER VON MUSIC GROUP UND SIND NICHT BERECHTIGT, MUSIC GROUP DURCH AUSDRCKLICHE ODER STILLSCHWEIGENDE HANDLUNGEN ODER REPRSENTANZEN ZU VERPFLICHTEN. DIESE BEDIENUNGSANLEITUNG IST URHEBERRECHTLICH GESCHTZT. KEIN TEIL DIESES HANDBUCHS DARF IN IRGENDEINER FORM ODER MIT IRGENDWELCHEN MITTELN ELEKTRONISCH ODER MECHANISCH, INKLUSIVE FOTOKOPIE ODER AUFNAHME, ZU IRGENDEINEM ZWECK OHNE DIE SCHRIFTLICHE ZUSTIMMUNG DER FIRMA MUSIC GROUP IP LTD. VERVIELFLTIGT ODER BERTRAGEN WERDEN.

ALLE RECHTE VORBEHALTEN. 2013 MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, British Virgin Islands

Die geltenden Garantiebedingungen und zustzliche Informationen bezglich der von MUSIC Group gewhrten beschrnkten Garantie fi nden Sie online unter www. music-group.com/warranty.

Aviso! Terminais marcados com o smbolo carregam corrente

eltrica de magnitude sufi ciente para constituir um risco de choque eltrico. Use apenas cabos de alto-falantes de alta qualidade com plugues TS de " ou plugues com trava de toro pr-instalados. Todas as outras instalaes e modifi caes devem ser efetuadas por pessoas qualifi cadas.

Este smbolo, onde quer que o encontre, alerta-o para a leitura das instrues de

manuseamento que acompanham o equipamento. Por favor leia o manual de instrues.

Ateno De forma a diminuir o risco de choque elctrico,

no remover a cobertura (ou a seco de trs). No existem peas substituveis por parte do utilizador no seu interior. Para esse efeito recorrer a um tcnico qualifi cado.

Ateno Para reduzir o risco de incndios ou choques

elctricos o aparelho no deve ser exposto chuva nem humidade. Alm disso, no deve ser sujeito a

salpicos, nem devem ser colocados em cima do aparelho objectos contendo lquidos, tais como jarras.

Ateno Estas instrues de operao devem ser utilizadas,

em exclusivo, por tcnicos de assistncia qualifi cados. Para evitar choques elctricos no proceda a reparaes ou intervenes, que no as indicadas nas instrues de operao, salvo se possuir as qualifi -caes necessrias. Para evitar choques elctricos no proceda a reparaes ou intervenes, que no as indicadas nas instrues de operao. S o dever fazer se possuir as qualifi caes necessrias. 1. Leia estas instrues. 2. Guarde estas instrues. 3. Preste ateno a todos os avisos. 4. Siga todas as instrues. 5. No utilize este dispositivo perto de gua. 6. Limpe apenas com um pano seco. 7. No obstrua as entradas de ventilao. Instale de acordo com as instrues do fabricante. 8. No instale perto de quaisquer fontes de calor tais como radiadores, bocas de ar quente, foges de sala ou outros aparelhos (incluindo amplifi cadores) que produzam calor. 9. No anule o objectivo de segurana das fi chas polarizadas ou do tipo de ligao terra. Uma fi cha polarizada dispe de duas palhetas sendo uma mais larga do que a outra. Uma fi cha do tipo ligao terra dispe de duas palhetas e um terceiro dente de ligao terra. A palheta larga ou o terceiro dente so fornecidos para sua segurana. Se a fi cha fornecida no encaixar na sua tomada, consulte um electricista para a substituio da tomada obsoleta. 10. Proteja o cabo de alimentao de pisadelas ou apertos, especialmente nas fi chas, extenses, e no local de sada da unidade. Certifi que-se de que o cabo elctrico est protegido. Verifi que particularmente nas fi chas, nos receptculos e no ponto em que o cabo sai do aparelho.

11. O aparelho tem de estar sempre conectado rede elctrica com o condutor de proteco intacto. 12. Se utilizar uma fi cha de rede principal ou uma tomada de aparelhos para desligar a unidade de funcionamento, esta deve estar sempre acessvel. 13. Utilize apenas ligaes/acessrios especifi cados pelo fabricante.

14. Utilize apenas com o carrinho, estrutura, trip, suporte, ou mesa especifi cados pelo fabricante ou

vendidos com o dispositivo. Quando utilizar um carrinho, tenha cuidado ao mover o conjunto carrinho/dispositivo para evitar danos provocados pela terpidao. 15. Desligue este dispositivo durante as trovoadas ou quando no for utilizado durante longos perodos de tempo. 16. Qualquer tipo de reparao deve ser sempre efectuado por pessoal qualifi cado.  necessria uma reparao sempre que a unidade tiver sido de alguma forma danifi cada, como por exemplo: no caso do cabo de alimentao ou fi cha se encontrarem danifi cados; na eventualidade de lquido ter sido derramado ou objectos terem cado para dentro do dispositivo; no caso da unidade ter estado exposta chuva ou humidade; se esta no funcionar normalmente, ou se tiver cado.

17. Correcta eliminao deste produto: este smbolo indica que o produto no deve ser eliminado juntamente com os

resduos domsticos, segundo a Directiva REEE (2002/96/CE) e a legislao nacional. Este produto dever ser levado para um centro de recolha licenciado para a reciclagem de resduos de equipamentos elctricos e electrnicos (EEE). O tratamento incorrecto deste tipo de resduos pode ter um eventual impacto negativo no ambiente e na sade humana devido a substncias potencialmente perigosas que esto geralmente associadas aos EEE. Ao mesmo tempo, a sua colaborao para a eliminao correcta deste produto ir contribuir para a utilizao efi ciente dos recursos naturais. Para mais informao acerca dos locais

onde poder deixar o seu equipamento usado para reciclagem, favor contactar os servios municipais locais, a entidade de gesto de resduos ou os servios de recolha de resduos domsticos.

ESPECIFICAES TCNICAS E APARNCIA ESTO SUJEITAS A MUDANAS SEM AVISO PRVIO E NO H GARANTIA DE PRECISO. BEHRINGER, KLARK TEKNIK, MIDAS, BUGERA, E TURBOSOUND FAZEM PARTE DO MUSIC GROUP (MUSIC-GROUP.COM). TODAS AS MARCAS REGISTADAS SO PROPRIEDADE DOS SEUS RESPECTIVOS PROPRIETRIOS. MUSIC GROUP NO SE RESPONSABILIZA POR QUALQUER PERDA QUE POSSA TER SIDO SOFRIDA POR QUALQUER PESSOA QUE ACREDITA TANTO COMPLETA QUANTO PARCIALMENTE EM QUALQUER DESCRIO, FOTO OU AFIRMAO AQUI CONTIDA. CORES E ESPECIFICAES PODEM VARIAR UM POUCO DO PRODUTO. OS PRODUTOS DA MUSIC GROUP SO VENDIDOS ATRAVS DE DISTRIBUIDORES AUTORIZADOS APENAS. DISTRIBUIDORES E REVENDEDORES NO SO AGENTES DA MUSIC GROUP E NO TM AUTORIDADE ALGUMA PARA OBRIGAR A MUSIC GROUP A QUALQUER TAREFA OU REPRESENTAO EXPRESSA OU IMPLCITA. ESTE MANUAL TEM DIREITOS AUTORAIS. PARTE ALGUMA DESTE MANUAL PODE SER REPRODUZIDA OU TRANSMITIDA DE QUALQUER FORMA OU MEIO, ELETRNICO OU MECNICO, INCLUINDO FOTOCPIA E GRAVAO DE QUALQUER TIPO, PARA QUALQUER INTENO, SEM A PERMISSO ESCRITA EXPRESSA DE MUSIC GROUP IP LTD.

TODOS DIREITOS RESERVADOS. 2013 MUSIC Group IP Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, Ilhas Virgens Britnicas

Para obter os termos de garantia aplicveis e condies e informaes adicionais a respeito da garantia limitada do MUSIC group, favor verifi car detalhes na ntegra atravs do website www.music-group.com/warranty.

BESCHRNKTE GARANTIE

HAFTUNGSAUSSCHLUSS

Instrues de Segurana Importantes

GARANTIA LIMITADA

LEGAL RENUNCIANTE

6 7Quick Start GuideMINIFEX FEX800

(EN) Controls

MINIFEX FEX800 Controls 8 MINIFEX FEX800 9 Quick Start Guide

(2)

(1) (8)

(3) (4) (5) (6) (7) (9) (10) (11) (12) (14)(13)

(1) The two LED displays show the effect preset currently selected. One LED is assigned to each preset.

(2) Use the PRESETS control to select one of the 16 effect presets.

(3) The EDIT control allows you to edit one effect parameter. The center position corresponds to the default setting programmed for the preset.

(4) The TAP/SELECT button performs two functions:

TAP (tempo entry): Hit the button several times in the tempo of the music piece to adapt the delay time of presets 9 and 15 or the modulation speed of presets 10-12. The button starts flashing in the corresponding tempo.

SELECT (additional effect parameter): Press this button to choose between two different effect characteristics when using presets 1-8, 13-14, 16. When the button lights up this means that the corresponding parameter of the selected preset has been activated.

(5) Use the INPUT LEVEL control to adjust the input signal level. Please be sure to set a level that is sufficiently high but does not overload the unit.

(6) The L + R LED display is for monitoring the input level. It comprises 6 LEDs. When the CLIP LED lights up, this indicates that digital distortion may occur at the input of the FEX800. In this case, the input signal level must be reduced.

(7) Use the MIX BALANCE control to adjust the ratio of original vs. effect signal. Turn the control fully to the right to hear only the processed effect signal. Turn it fully to the left to hear only the unprocessed input signal.

(8) The IN/OUT button enables/disables the effect signal. The button lights up when the input signal is being processed by the FEX800. In order to hear the processed signal you have to set a suitable ratio of effect vs. direct signal using the MIX BALANCE control (7).

(9) Use the OUTPUT LEVEL control to adjust the output level.

(10) The switch turns your MINIFEX FEX800 on and off. The switch lights up when the unit is switched on.

(11) The FEX800 is connected to the mains using a 2-pole POWER connector jack. A matching mains adaptor is included with the unit.

(12) A single footswitch can be connected to the IN/OUT connector. This footswitch allows you to remotely control the IN/OUT button (8) on the front panel and switch the effect signal on and off.

(13) The two OUTPUT connectors are on 1/4" connectors and provide a balanced left/right signal.

(14) The two INPUT connectors are on 1/4" connectors and can be used for unbalanced signals. A single mono signal should be connected to the L jack.

Check Out behringer.com for Full Manual

Front panel control elements of the FEX800 Rear panel connectors of the FEX800

(ES) Controles

MINIFEX FEX800 Controles 10 MINIFEX FEX800 11 Quick Start Guide

(2)

(1) (8)

(3) (4) (5) (6) (7) (9) (10) (11) (12) (14)(13)

Rear panel connectors of the FEX800 Conexiones en la parte trasera del FEX800

(1) Estos LED indican el preset seleccionado. Cada preset tiene un LED asignado.

(2) El control PRESETS le permite seleccionar uno de los 16 efectos.

(3) Este control le permite EDIT(ar) un parmetro especfico del efecto seleccionado. En la posicin central, el parmetro tiene el valor original de fbrica.

(4) El botn TAP/SELECT tiene dos funciones:

TAP (ajuste de tempo/velocidad): pulse un par de veces el botn TAP al tempo de una cancin para ajustar a ste el tiempo de retraso (delay) de los presets (9) y (15), o la velocidad de modulacin de los presets (10-12). El botn parpadear a la velocidad/ tempo correspondiente.

SELECT (parmetros adicionales): al pulsar el botn, el parmetro correspondiente (ver la Tabla 6.1) de los presets (1-8, 13-14, 16) conmuta entre dos valores preestablecidos. Si el botn est iluminado, el parmetro asume el valor secundario asignado a ste. Si el botn no est iluminado, el parmetro conserva su valor original.

(5) Utilice el control INPUT LEVEL para regular el nivel de la seal de entrada. Asegrese de que el nivel sea suficientemente alto, sin llegar a distorsionar.

(6) El medidor de seis segmentos L+R le permite monitorizar el nivel de entrada. Si se ilumina el LED CLIP, esto indica que la seal de entrada puede estar distorsionando. En dado caso, reduzca el nivel de entrada.

(7) El control MIX BALANCE le permite ajustar la relacin entre la seal original y la seal con efecto. Para escuchar slo la seal con efecto, gire el control completamente a la derecha. Para escuchar la seal original, sin efecto, gire el control completamente a la izquierda.

(8) El botn IN/OUT permite activar y desactivar la seal del FEX800, a manera de bypass. Si el botn est iluminado, la seal est siendo procesada por el FEX800. Para poder escuchar la seal procesada debe ajustar el balance adecuado entre las seales con y sin efecto, mediante el control MIX BALANCE (7).

(9) Utilice el control OUTPUT LEVEL para regular el nivel de salida.

(10) Con el interruptor se enciende el MINIFEX FEX800. Al encender el procesador, se ilumina este interruptor.

(11) La conexin a la red elctrica se realiza mediante el conector POWER. En el suministro encontrar un adaptador de corriente adecuado.

(12) El conector IN/OUT le permite utilizar un pedal para activar o desactivar, a manera de bypass, el procesamiento de seal del FEX800 de manera remota.

(13) Las salidas OUTPUT transmiten una seal estreo (L/R) mediante jacks balanceados de 6,3 mm.

(14) Ambas entradas INPUT estn provistas de jacks mono no balanceados de 6,3 mm. Si la fuente de seal es mono, conctela en la entrada izquierda (L).

Si quiere acceder al manual de instrucciones completo, vaya a la pgina web behringer.com

MINIFEX FEX800 Rglages 12 MINIFEX FEX800 13 Quick Start Guide

(FR) Rglages

(2)

(1) (8)

(3) (4) (5) (6) (7) (9) (10) (11) (12) (14)(13)

(1) Ces colonnes de LED indiquent la preset slectionne. A chaque preset correspond une LED.

(2) Utilisez lencodeur PRESETS pour slectionner lun des 16 programmes deffet.

(3) La commande EDIT sert la modification de la valeur dun paramtre deffet. La position centrale correspond la valeur dusine de ce paramtre.

(4) La touche TAP/SELECT possde deux fonctions :

TAP (saisie du tempo/de la vitesse) : appuyez plusieurs fois sur cette touche au rythme de la musique pour adapter le temps de delay des presets (9) et (15) ou la vitesse de modulation des presets (10 12). La touche clignote la vitesse saisie.

SELECT (paramtre deffet supplmentaire) : appuyez sur cette touche pour commuter entre deux couleurs deffet diffrentes pour les presets (1 8, 13 14 et 16). Lorsque la touche est allume, le paramtre supplmentaire de la preset slectionne est actif.

(5) Utilisez le potentiomtre INPUT LEVEL pour ajuster le niveau du signal de lentre. Veillez rgler un niveau suffisamment lev sans toutefois faire saturer le processeur.

(6) La chane de 6 LED L+R permet de visualiser le niveau dentre. La LED CLIP sallume pour vous signaler que des distorsions numriques peuvent apparatre dans ltage dentre du FEX800. Dans ce cas, rduisez le niveau du signal en entre.

(7) Tournez le potentiomtre MIX BALANCE pour dterminer le rapport de volume entre le signal deffet et le signal original. Placez ce potentiomtre en bute droite pour nentendre que le signal deffet. Inversement, positionnez-le en bute gauche pour nentendre que le signal source sans traitement.

(8) Appuyez sur la touche IN/OUT pour activer ou dsactiver le signal deffet. Lorsque la touche est allume, le signal source est trait par le FEX800. Pour pouvoir entendre le signal trait, vous devez rgler une proportion de signal deffet suffisante par rapport au signal original laide du potentiomtre MIX BALANCE (7).

(9) Tournez le potentiomtre OUTPUT LEVEL pour rgler le niveau du signal de sortie.

(10) Appuyez sur le commutateur pour allumer le MINIFEX FEX800. La touche reste allume tant que lappareil est en service.

(11) On effectue la liaison avec la tension secteur par lintermdiaire du bloc dalimentation externe fourni et de lembase bipolaire POWER.

(12) Le connecteur IN/OUT est conu pour le cblage dune pdale de commutation qui permettra alors de commander distance la fonction de la touche IN/OUT (8) du MINIFEX, autrement dit dactiver ou de dsactiver leffet.

(13) Les sorties OUTPUT L (gauche) et R (droite) sont des embases jack de 6,3 mm. Elles dlivrent un signal stro symtrique.

(14) Les entres INPUT L (gauche) et R (droite) sont des embases jack asymtriques de 6,3 mm. Si le signal source est mono, reliez-le lentre INPUT L.

Consultez le site behringer.com pour tlcharger le mode demploi complet

Commandes de la face avant du FEX800 Connexions du panneau arrire du FEX800

MINIFEX FEX800 Regler (DE) Schritt 2: Regler

(2)

(1) (8)

(3) (4) (5) (6) (7) (9) (10) (11) (12) (14)(13)

(1) Die beiden LED-Ketten zeigen das ausgewhlte Effekt-Preset an. Jedem Preset ist eine LED zugeordnet.

(2) Mit dem PRESETS-Regler whlen Sie eines der 16 Effekt-Presets aus.

(3) Mit dem EDIT-Regler knnen Sie einen Effektparameter verndern. Die Mittelstellung entspricht der werksseitigen Einstellung des Presets.

(4) Der TAP/SELECT-Taster erfllt zwei Funktionen:

TAP (Tempo-/Geschwindigkeitseingabe) : Drcken Sie den Taster mehrmals im Tempo des Musikstcks, um die Delay-Zeit der Presets (9) und (15) oder die Modulationsgeschwindigkeit der Presets (10-12) anzupassen. Der Taster blinkt mit der entsprechenden Geschwindigkeit.

SELECT (Zustzlicher Effektparameter) : Durch Drcken des Tasters schalten Sie bei den Presets (1-8, 13-14, 16) zwischen zwei unterschiedlichen Effektcharakteristika um. Leuchtet der Taster, so ist der jeweilige Parameter des gewhlten Presets aktiviert.

(5) Mit dem INPUT LEVEL-Regler stellen Sie den Pegel des Eingangssignals ein. Achten Sie darauf, dass Sie den Pegel ausreichend hoch einstellen, ohne jedoch zu bersteuern.

(6) Mit Hilfe der L+R LED-Kette berwachen Sie den Eingangspegel. Dabei stehen Ihnen 6 LEDs zur Verfgung. Ein Aufleuchten der CLIP-LED signalisiert, dass am Eingang des FEX800 digitale Verzerrungen auftreten knnten. Reduzieren Sie dann den Pegel des Eingangssignals.

(7) Mit Hilfe des MIX BALANCE-Reglers bestimmen Sie das Verhltnis von Original- und Effektsignal. Drehen Sie den Regler ganz nach rechts, um nur das bearbeitete Effektsignal zu hren. Drehen Sie den Regler ganz nach links, um ausschlielich das unbearbeitete Eingangssignal zu hren.

(8) Mit dem IN/OUT-Taster schalten Sie das Effektsignal ein oder aus. Leuchtet der Taster, wird das Signal vom FEX800 bearbeitet. Damit Sie das bearbeitete Signal hren knnen, mssen Sie mit Hilfe des MIX BALANCE-Regler (7) ein entsprechendes Verhltnis von Effekt- und Direktsignal einstellen.

(9) Benutzen Sie den OUTPUT LEVEL-Regler, um den Ausgangspegel einzustellen.

(10) Mit dem -Schalter nehmen Sie den MINIFEX FEX800 in Betrieb. Ist das Gert eingeschaltet, leuchtet der Schalter.

(11) Die Stromversorgung erfolgt ber die zweipolige POWER-Anschlussbuchse. Ein passender Netzadapter gehrt zum Lieferumfang.

(12) An den IN/OUT-Anschluss knnen Sie einen einfachen Futaster (Footswitch) anschlieen. Damit knnen Sie den IN/OUT- Taster (8) auf der Frontseite des Gertes fernbedienen und das Effektsignal des MINIFEX an- oder abschalten.

(13) Die beiden OUTPUT-Buchsen sind fr den Anschluss von 6,3-mm-Klinkensteckern ausgelegt und liefern ein symmetrisch gefhrtes L/R-Signal.

(14) Die beiden INPUT-Buchsen sind fr den Anschluss von 6,3-mm-Klinkensteckern ausgelegt und knnen mit unsymmetrischen Signalen belegt werden. Ein Monosignal schlieen Sie an der L-Buchse an.

Das komplette Handbuch finden Sie unter behringer.com

Bedienungselemente auf der Frontseite des FEX800 Anschlsse auf der Rckseite des FEX800

14 MINIFEX FEX800 15 Quick Start Guide

MINIFEX FEX800 Controles (PT) Controles

(2)

(1) (8)

(3) (4) (5) (6) (7) (9) (10) (11) (12) (14)(13)

(1) Ambas as correntes LED apresentam a predefinio de efeitos seleccionada. Cada predefinio atribuda a um LED.

(2) Com o regulador PRESETS, seleccione uma das 16 predefinies de efeitos.

(3) Com o regulador EDIT, pode alterar um parmetro de efeitos. A posio central corresponde regulao da predefinio de fbrica.

(4) A tecla TAP/SELECT cumpre duas funes:

(5) TAP (andamento/velocidade): Prima repetidamente a tecla no andamento de uma pea musical para ajustar o tempo de atraso da predefinio (9) e (15) ou a velocidade de modulao da predefinio (10-12). A tecla pisca com a velocidade correspondente.

(6) SELECT (parmetro de efeitos adicional): Ao premir a tecla, alterna as predefinies (1-8, 13-14, 16) entre duas caractersticas de efeitos diferentes. A tecla acende quando o respectivo parmetro da predefinio seleccionada est activado.

(7) Com o regulador INPUT LEVEL, ajuste o nvel do sinal de entrada. Certifique-se de que ajusta o nvel para um valor suficientemente elevado, sem, no entanto, sobrecarregar.

(8) Com a corrente LED L+R, controle o nvel de entrada. Para tal, tem disposio 6 LEDs. Se o LED CLIP acender, significa que podem ocorrer distores digitais entrada do FEX800. Nesse caso, reduza o nvel do sinal de entrada.

(9) Com o regulador MIX BALANCE, determina a proporo do sinal original e do sinal de efeitos. Rode o regulador completamente para a direita, para escutar apenas o sinal de efeitos processado. Rode o regulador completamente para a esquerda, para escutar exclusivamente o sinal de entrada no trabalhado.

(10) Com a tecla IN/OUT, ligue e desligue o sinal de efeitos. A tecla acende-se quando o sinal processado pelo FEX800. Para poder ouvir o sinal trabalhado, tem de regular a proporo correspondente do sinal de efeitos e do sinal directo com o regulador MIX BALANCE (7).

(11) Utilize o regulador OUTPUT LEVEL para ajustar o nvel de sada.

(12) Com o interruptor, coloque o MINIFEX FEX800 em funcionamento. Se o aparelho estiver aceso, o interruptor acende--se.

(13) A fonte de alimentao dispe de um conector de ligao POWER de dois plos. fornecido um adaptador de rede adequado.

(14) Na conexo IN/OUT, pode ligar um interruptor de pedal simples (Footswitch). Com isto, pode comandar a tecla IN/OUT (8) da parte frontal do aparelho e activar ou desactivar o sinal de efeitos do MINIFEX.

(15) Ambos os conectores OUTPUT destinam-se ligao de conectores de 6,3 mm e emitem um sinal simtrico E/D.

(16) Ambos os conectores INPUT destinam-se ligao de conectores de 6,3 mm e podem ser cobertos com sinais assimtricos. Um sinal mono associado ao conector L.

Verifique o site behringer.com para obter o manual completo Full Manual

Comandos da face frontal do FEX800 Connexions du panneau arrire du FEX800

16 MINIFEX FEX800 17 Quick Start Guide

Specifications Especificaciones tcnicas 18 19Quick Start GuideMINIFEX FEX800

Input

Type 1/4" TS connectors, unbalanced

Impedance approx. 30 k

Output

Type 1/4" TRS connectors, impedance balanced

Impedance approx. 220

Max. output level +10 dBu

In/Out

Type 1/4" TS footswitch connector

Digital Processing

Converters 24-Bit Delta-Sigma, 128-times oversampling

Sampling rate 48 kHz

System Specifications

Frequency response 10 Hz to 22 kHz, -3 dB

Dynamic range 96 dB, 10 Hz to 22 kHz

Distortion 0,01% typ. @ 0 dBFS

Crosstalk -75 dB @ 1 kHz

Signal-to-noise ratio 10 Hz to 22 kHz <86 dB @ 0 dBu, A-weighted

Power Supply

Mains connection external power supply, 9 V~, 750 mA

Mains Voltage

USA/Canada 120 V~, 60 Hz

U.K./Australia 240 V~, 50 Hz

China 220 V~, 50 Hz

Europe 230 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

Power consumption approx. 7.5 W

Dimensions/Weight

Dimensions (H x W x D) approx. 1.9 x 4.7 x 9.6" approx. 48 x 120 x 242.6 mm

Weight approx. 1.46 lbs / 0.66 kg

Conectores jack mono de 6,3 mm, no balanceados

Impedancia de entrada aprox. 30 k

Salida (Output)

Conectores jack estreo de 6,3 mm, balanceados

Impedancia de salida mn. 220

Nivel de salida mx. +10 dBu

In/Out

Conector jack mono de 6,3 mm (pedal)

Procesamiento Digital

Convertidor Delta-Sigma de 24 bits, sobremuestreo de 128x

Frecuencia de muestreo 48 kHz

Datos de Sistema

Respuesta en frecuencia 10 Hz a 22 kHz, - 3 dB

Dinmica 96 dB, 10 Hz a 22 kHz

THD 0,01% tp. @ 0 dBFS

Diafona -75 dB @ 1 kHz

Relacin seal a ruido 10 Hz a 22 kHz <86 dB @ 0 dBu, ponderado A

Suministro de Corriente

Conexin de red adaptador de corriente externo, 9 V~, 750 mA

Tensin de Red

EE.UU./Canad 120 V~, 60 Hz

R.U./Australia 240 V~, 50 Hz

China 220 V~, 50 Hz

Europa 230 V~, 50 Hz

Japn 100 V~, 50 - 60 Hz

Consumo de potencia aprox. 7,5 W

Dimensiones/Peso

Dimensiones (alt. x anch. x prof.) aprox. 48 x 120 x 242,6 mm

Peso aprox. 0,66 kg

Entrada (Input)

Caractristiques techniques Technische Daten 20 21Quick Start GuideMINIFEX FEX800

Input (Entre)

Connecteurs Embases jack de 6,3 mm, asymtriques

Impdance dentre Env. 30 k

Output (Sortie)

Connecteurs Embases jack de 6,3 mm, symtriques

Impdance dentre Min. 220

Niveau de sortie max. +10 dBu

In/Out (Pdale)

Connecteur Embase jack mono de 6,3 mm

Traitements Numeriques

Convertisseur Delta-Sigma 24 bits, surchantillonnage 128x

Frquence dchantillonnage 48 kHz

Caracteristiques du Systeme

Bande passante De 10 Hz 22 kHz, - 3 dB

Dynamique 96 dB, de 10 Hz 22 kHz

Distorsion 0,01% typ. @ 0 dBFS

Diaphonie -75 dB @ 1 kHz

Rapport signal/bruit De 10 Hz 22 kHz <86 dB @ 0 dBu, A pondr

Alimentation Electrique

Connexion secteur Bloc dalimentation externe, 9 V~, 750 mA

Tension Secteur

Etats-Unis/Canada 120 V~, 60 Hz

Royaume-Uni/Australie 240 V~, 50 Hz

Chine/Core 220 V~, 50 Hz

Europe 230 V~, 50 Hz

Japon 100 V~, 50 - 60 Hz

Consommation lectrique Env. 7,5 W

Dimensions/Poids

Dimensions (H x L x P) Env. 48 x 120 x 242,6 mm

Poids Env. 0,66 kg

Input

Anschlsse 6,3-mm-Monoklinke, unsymmetrisch

Eingangsimpedanz ca. 30 k

Output

Anschlsse 6,3-mm-Stereoklinke, impedanz-symmetrisch

Ausgangsimpedanz min. 220

Maximaler Ausgangspegel +10 dBu

In/Out

Anschluss 6,3-mm-Monoklinke (Futaster)

Digitale Verarbeitung

Wandler 24-Bit Delta-Sigma, 128-faches Oversampling

Abtastrate 48 kHz

Systemdaten

Frequenzgang 10 Hz bis 22 kHz, - 3 dB

Dynamik 96 dB, 10 Hz bis 22 kHz

Klirrfaktor 0,01% typ. @ 0 dBFS

Signalbersprechen -75 dB @ 1 kHz

Rauschabstand 10 Hz bis 22 kHz <86 dB @ 0 dBu, A-gewichtet

Stromversorgung

Netzanschluss externer Netzadapter, 9 V~, 750 mA

Netzspannung

USA/Kanada 120 V~, 60 Hz

U.K./Australien 240 V~, 50 Hz

China 220 V~, 50 Hz

Europa 230 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

Leistungsaufnahme ca. 7,5 W

Abmessungen/Gewicht

Abmessungen (H x B x T) ca. 48 x 120 x 242,6 mm

Gewicht ca. 0,66 kg

Dados tcnicos 22 23Quick Start GuideMINIFEX FEX800

Entrada

Ligaes conector mono de 6,3 mm, assimtrico

Impedncia de entrada cerca de 30 k

Sada

Ligaes conector estreo de 6,3 mm, impedncia simtrica

Impedncia de sada mn. 220

Nvel mx. sada +10 dBu

In/Out

Ligao conector mono de 6,3 mm (interruptor de pedal)

Tratamento Digital

Transformador 24 bits Delta-Sigma, 128 Oversampling

Taxa de amostragem 48 kHz

Dados do Sistema

Intervalo de frequncia 10 Hz a 22 kHz, - 3 dB

Dinmica 96 dB, 10 Hz a 22 kHz

Factor de distoro 0,01% tip. @ 0 dBFS

Interferncia do sinal -75 dB @ 1 kHz

Rcio sinal/rudo 10 Hz a 22 kHz <86 dB @ 0 dBu, ponderao A

Alimentao

Ligao de rede adaptador de rede externo, 9 V~, 750 mA

Tenso de Rede

USA/Canad 120 V~, 60 Hz

U.K./Austrlia 240 V~, 50 Hz

China 220 V~, 50 Hz

Europa 230 V~, 50 Hz

Japo 100 V~, 50 - 60 Hz

Consumo de energia cerca de 7,5 W

Dimenses/Peso

Dimenses (A x L x P) cerca de 48 x 120 x 242,6 mm

Peso cerca de 0,66 kg

Other important information

1. Register online. Please register your new MUSIC Group equipment right after you purchase it by visiting behringer. com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.

2. Malfunction. Should your MUSIC Group Authorized Reseller not be located in your vicinity, you may contact the MUSIC Group Authorized Fulfiller for your country listed under Support at behringer. com. Should your country not be listed, please check if your problem can be dealt with by our Online Support which may also be found under Support at behringer. com. Alternatively, please submit an online warranty claim at behringer. com BEFORE returning the product.

3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

1. Registro online. Le recomendamos que registre su nuevo aparato MUSIC Group justo despus de su compra accediendo a la pgina web behringer. com. El registro de su compra a travs de nuestro sencillo sistema online nos ayudar a resolver cualquier incidencia que se presente a la mayor brevedad posible. Adems, aproveche para leer los trminos y condiciones de nuestra garanta, si es aplicable en su caso.

2. Averas. En el caso de que no exista un distribuidor MUSIC Group en las inmediaciones, puede ponerse en contacto con el distribuidor MUSIC Group de su pas, que encontrar dentro del apartado Support de nuestra pgina web behringer. com. En caso de que su pas no aparezca en ese listado, acceda a la seccin Online Support (que tambin encontrar dentro del apartado Support de nuestra pgina web) y compruebe si su problema aparece descrito y solucionado all. De forma alternativa, envenos a travs de la pgina web una solicitud online de soporte en periodo de garanta ANTES de devolvernos el aparato.

3. Conexiones de corriente. Antes de enchufar este aparato a una salida de corriente, asegrese de que dicha salida sea del voltaje adecuado para su modelo concreto. En caso de que deba sustituir un fusible quemado, deber hacerlo por otro de idnticas especificaciones, sin excepcin.

1. Enregistrez-vous en ligne. Prenez le temps denregistrer votre produit MUSIC Group aussi vite que possible sur le site Internet behringer. com. Le fait denregistrer le produit en ligne nous permet de grer les rparations plus rapidement et plus efficacement. Prenez galement le temps de lire les termes et conditions de notre garantie.

2. Dysfonctionnement. Si vous navez pas de revendeur MUSIC Group prs de chez vous, contactez le distributeur MUSIC Group de votre pays : consultez la liste des distributeurs de votre pays dans la page Support de notre site Internet behringer. com. Si votre pays nest pas dans la liste, essayez de rsoudre votre problme avec notre aide en ligne que vous trouverez galement dans la section Support du site behringer. com. Vous pouvez galement nous faire parvenir directement votre demande de rparation sous garantie par Internet sur le site behringer. com AVANT de nous renvoyer le produit.

3. Raccordement au secteur. Avant de relier cet quipement au secteur, assurez-vous que la tension secteur de votre rgion soit compatible avec lappareil. Veillez remplacer les fusibles uniquement par des modles exactement de mme taille et de mme valeur lectrique sans aucune exception.

Important information Aspectos importantes Informations importantes

1. Online registrieren. Bitte registrieren Sie Ihr neues MUSIC Group-Gert direkt nach dem Kauf auf der Website behringer. com. Wenn Sie Ihren Kauf mit unserem einfachen online Formular registrieren, knnen wir Ihre Reparaturansprche schneller und effizienter bearbeiten. Lesen Sie bitte auch unsere Garantiebedingungen, falls zutreffend.

2. Funktionsfehler. Sollte sich kein MUSIC Group Hndler in Ihrer Nhe befinden, knnen Sie den MUSIC Group Vertrieb Ihres Landes kontaktieren, der auf behringer. com unter Support aufgefhrt ist. Sollte Ihr Land nicht aufgelistet sein, prfen Sie bitte, ob Ihr Problem von unserem Online Support gelst werden kann, den Sie ebenfalls auf behringer. com unter Support finden. Alternativ reichen Sie bitte Ihren Garantieanspruch online auf behringer. com ein, BEVOR Sie das Produkt zurcksenden.

3. Stromanschluss. Bevor Sie das Gert an eine Netzsteckdose anschlieen, prfen Sie bitte, ob Sie die korrekte Netzspannung fr Ihr spezielles Modell verwenden. Fehlerhafte Sicherungen mssen ausnahmslos durch Sicherungen des gleichen Typs und Nennwerts ersetzt werden.

1. Registre-se online. Por favor, registre seu novo equipamento MUSIC Group logo aps a compra visitando o site behringer. com Registrar sua compra usando nosso simples formulrio online nos ajuda a processar seus pedidos de reparos com maior rapidez e eficincia. Alm disso, leia nossos termos e condies de garantia, caso seja necessrio.

2. Funcionamento Defeituoso. Caso seu fornecedor MUSIC Group no esteja localizado nas proximidades, voc pode contatar um distribuidor MUSIC Group para o seu pas listado abaixo de Suporte em behringer. com. Se seu pas no estiver na lista, favor checar se seu problema pode ser resolvido com o nosso Suporte Online que tambm pode ser achado abaixo de Suporteem behringer. com. Alternativamente, favor enviar uma solicitao de garantia online em behringer. com ANTES da devoluo do produto.

3. Ligaes. Antes de ligar a unidade tomada, assegure-se de que est a utilizar a voltagem correcta para o modelo em questo. Os fusveis com defeito tero de ser substitudos, sem qualquer excepo, por fusveis do mesmo tipo e corrente nominal.

Weitere wichtige Informationen

Outras Informaes Importantes

25Quick Start Guide24 MINIFEX FEX800

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible Party Name: MUSIC Group Services US Inc.

Address: 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA

Phone/Fax No.: Phone: +1 425 672 0816 Fax: +1 425 673 7647

MINIFEX FEX800

complies with the FCC rules as mentioned in the following paragraph:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important information:

Changes or modifications to the equipment not expressly approved by MUSIC Group can void the users authority to use the equipment.

MINIFEX FEX800

27Quick Start Guide26 MINIFEX FEX800

Manualsnet FAQs

If you want to find out how the FEX800 Behringer works, you can view and download the Behringer FEX800 Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Behringer FEX800 as well as other Behringer manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Behringer FEX800. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Behringer FEX800 Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Behringer FEX800 Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Behringer FEX800 Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Behringer FEX800 Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Behringer FEX800 Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.