Behringer K450FX Quick Start Guide PDF

1 of 16
1 of 16

Summary of Content for Behringer K450FX Quick Start Guide PDF

Quick Start Guide

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Ultra-Flexible 300/180/90/45-Watt 4/3-Channel PA System / Keyboard Amplifier with FX and FBQ Feedback Detection

V 5.0

2 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 3

Las terminales marcadas con este smbolo transportan corriente elctrica de magnitud suficiente como para constituir

un riesgo de descarga elctrica. Utilice solo cables de altavoz profesionales y de alta calidad con conectores TS de 6,3 mm o de bayoneta prefijados. Cualquier otra instalacin o modificacin debe ser realizada nicamente por un tcnico cualificado.

Este smbolo, siempre que aparece, le advierte de la presencia de voltaje peligroso sin aislar dentro de la caja;

este voltaje puede ser suficiente para constituir un riesgo de descarga.

Este smbolo, siempre que aparece, le advierte sobre instrucciones operativas y de mantenimiento que aparecen en la

documentacin adjunta. Por favor, lea el manual.

Atencin Para reducir el riesgo de descarga elctrica, no quite la tapa (o la parte

posterior). No hay piezas en el interior del equipo que puedan ser reparadas por el usuario. Si es necesario, pngase en contacto con personal cualificado.

Atencin Para reducir el riesgo de incendio o descarga elctrica, no exponga este

aparato a la lluvia, humedad o alguna otra fuente que pueda salpicar o derramar algn lquido sobre el aparato. No coloque ningn tipo de recipiente para lquidos sobre el aparato.

Atencin Las instrucciones de servicio deben llevarlas a cabo exclusivamente personal

cualificado. Para evitar el riesgo de una descarga elctrica, no realice reparaciones que no se encuentren descritas en el manual de operaciones. Las reparaciones deben ser realizadas exclusivamente por personal cualificado.

1. Lea las instrucciones.

2. Conserve estas instrucciones.

3. Preste atencin a todas las advertencias.

4. Siga todas las instrucciones.

5. No use este aparato cerca del agua.

6. Limpie este aparato con un pao seco.

7. No bloquee las aberturas de ventilacin. Instale el equipo de acuerdo con las instrucciones del fabricante.

8. No instale este equipo cerca de fuentes de calor tales como radiadores, acumuladores de calor, estufas u otros aparatos (incluyendo amplificadores) que puedan producir calor.

9. No elimine o deshabilite nunca la conexin a tierra del aparato o del cable de alimentacin de corriente. Un enchufe polarizado tiene dos polos, uno de los cuales tiene un contacto ms ancho que el otro. Una clavija con puesta a tierra dispone de tres contactos: dos polos y la puesta a tierra. El contacto ancho y el tercer contacto, respectivamente, son los que garantizan una mayor seguridad. Si el enchufe suministrado con el equipo no concuerda con la toma de corriente, consulte con un electricista para cambiar la toma de corriente obsoleta.

10. Coloque el cable de suministro de energa de manera que no pueda ser pisado y que est protegido de objetos afilados. Asegrese de que el cable de suministro de energa est protegido, especialmente en la zona de la clavija y en el punto donde sale del aparato.

11. Use nicamente los dispositivos o accesorios especificados por el fabricante.

12. Use nicamente la carretilla, plataforma, trpode, soporte o mesa especificados por el fabricante o suministrados junto con el equipo. Al transportar el equipo, tenga cuidado para evitar

daos y cadas al tropezar con algn obstculo.

13. Desenchufe el equipo durante tormentas o si no va a utilizarlo durante un periodo largo.

14. Confe las reparaciones nicamente a servicios tcnicos cualificados. La unidad requiere mantenimiento siempre que haya sufrido algn dao, si el cable de suministro de energa o el enchufe presentaran daos, se hubiera derramado un lquido o hubieran cado objetos dentro del equipo, si el aparato hubiera estado expuesto a la humedad o la lluvia, si ha dejado de funcionar de manera normal o si ha sufrido algn golpe o cada.

15. Al conectar la unidad a la toma de corriente elctrica asegrese de que la conexin disponga de una unin a tierra.

16. Si el enchufe o conector de red sirve como nico medio de desconexin, ste debe ser accesible fcilmente.

17. Cmo debe deshacerse de este aparato: Este smbolo indica que este aparato no debe ser tratado como basura orgnica, segn lo indicado en la Directiva WEEE (2012/19/EU) y a las normativas aplicables en su pas.

En lugar de ello deber llevarlo al punto limpio ms cercano para el reciclaje de sus elementos elctricos / electrnicos (EEE). Al hacer esto estar ayudando a prevenir las posibles consecuencias negativas para el medio ambiente y la salud que podran ser provocadas por una gestin inadecuada de este tipo de aparatos. Adems, el reciclaje de materiales ayudar a conservar

los recursos naturales. Para ms informacin acerca del reciclaje de este aparato, pngase en contacto con el Ayuntamiento de su ciudad o con el punto limpio local.

18. No instale esta unidad en un espacio muy reducido, tal como encastrada en una librera o similar.

19. No coloque objetos con llama, como una vela encendida, sobre este aparato.

20. Tenga presentes todas las advertencias relativas al reciclaje y correcta eliminacin de las pilas. Las pilas deben ser siempre eliminadas en un punto limpio y nunca con el resto de la basura orgnica.

21. Puede usar este aparato en lugares con climas tropicales y moderados que soporten temperaturas de hasta 45C.

Music Tribe no admite ningn tipo de responsabilidad por cualquier dao o prdida que pudiera sufrir cualquier persona por confiar total o parcialmente en la descripciones, fotografas o afirmaciones contenidas en este documento. Las especificaciones tcnicas, imgenes y otras informaciones contenidas en este documento estn sujetas a modificaciones sin previo aviso. Todas las marcas comerciales que aparecen aqu son propiedad de sus respectivos dueos. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones y Coolaudio son marcas comerciales o marcas registradas de Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 Reservados todos los derechos.

Si quiere conocer los detalles y condiciones aplicables de la garanta as como informacin adicional sobre la Garanta limitada de Music Tribe, consulte online toda la informacin en la web community.musictribe.com/ pages/support#warranty.

Instrucciones de seguridad

NEGACIN LEGAL

GARANTA LIMITADA

Important Safety Instructions

LEGAL DISCLAIMER

LIMITED WARRANTY

Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock.

Use only high-quality professional speaker cables with " TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.

This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the

enclosure - voltage that may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the

accompanying literature. Please read the manual.

Caution To reduce the risk of electric shock, do not remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to qualified personnel.

Caution To reduce the risk of fire or electric shock, do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution These service instructions are for use by qualified service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Use only attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

17. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product

should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.

18. Do not install in a confined space, such as a book case or similar unit.

19. Do not place naked flame sources, such as lighted candles, on the apparatus.

20. Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.

21. This apparatus may be used in tropical and moderate climates up to 45C.

Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 All rights reserved.

For the applicable warranty terms and conditions and additional information regarding Music Tribes Limited Warranty, please see complete details online at community.musictribe.com/pages/support#warranty.

4 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 5

Vorsicht Die mit dem Symbol markierten Anschlsse fhren so viel Spannung,

dass die Gefahr eines Stromschlags besteht. Verwenden Sie nur hochwertige, professionelle Lautsprecherkabel mit vorinstallierten 6,35 mm MONO-Klinkensteckern oder Lautsprecherstecker mit Drehverriegelung. Alle anderen Installationen oder Modifikationen sollten nur von qualifiziertem Fachpersonal ausgefhrt werden.

Achtung Um eine Gefhrdung durch Stromschlag auszuschlieen, darf die Gerteabdeckung

bzw. Gerterckwand nicht abgenommen werden. Im Innern des Gerts befinden sich keine vom Benutzer reparierbaren Teile. Reparaturarbeiten drfen nur von qualifiziertem Personal ausgefhrt werden.

Achtung Um eine Gefhrdung durch Feuer bzw. Stromschlag auszuschlieen, darf dieses

Gert weder Regen oder Feuchtigkeit ausgesetzt werden noch sollten Spritzwasser oder tropfende Flssigkeiten in das Gert gelangen knnen. Stellen Sie keine mit Flssigkeit gefllten Gegenstnde, wie z. B. Vasen, auf das Gert.

Achtung Die Service-Hinweise sind nur durch qualifiziertes Personal zu befolgen.

Um eine Gefhrdung durch Stromschlag zu vermeiden, fhren Sie bitte keinerlei Reparaturen an dem Gert durch, die nicht in der Bedienungsanleitung beschrieben sind. Reparaturen sind nur von qualifiziertem Fachpersonal durchzufhren.

1. Lesen Sie diese Hinweise.

2. Bewahren Sie diese Hinweise auf.

3. Beachten Sie alle Warnhinweise.

4. Befolgen Sie alle Bedienungshinweise.

5. Betreiben Sie das Gert nicht in der Nhe von Wasser.

6. Reinigen Sie das Gert mit einem trockenen Tuch.

7. Blockieren Sie nicht die Belftungsschlitze. Beachten Sie beim Einbau des Gertes die Herstellerhinweise.

8. Stellen Sie das Gert nicht in der Nhe von Wrmequellen auf. Solche Wrmequellen sind z. B. Heizkrper, Herde oder andere Wrme erzeugende Gerte (auch Verstrker).

9. Entfernen Sie in keinem Fall die Sicherheitsvorrichtung von Zweipol- oder geerdeten Steckern. Ein Zweipolstecker hat zwei unterschiedlich breite Steckkontakte. Ein geerdeter Stecker hat zwei Steckkontakte und einen dritten Erdungskontakt. Der breitere Steckkontakt oder der zustzliche

Erdungskontakt dient Ihrer Sicherheit. Falls das mitgelieferte Steckerformat nicht zu Ihrer Steckdose passt, wenden Sie sich bitte an einen Elektriker, damit die Steckdose entsprechend ausgetauscht wird.

10. Verlegen Sie das Netzkabel so, dass es vor Tritten und scharfen Kanten geschtzt ist und nicht beschdigt werden kann. Achten Sie bitte insbesondere im Bereich der Stecker, Verlngerungskabel und an der Stelle, an der das Netzkabel das Gert verlsst, auf ausreichenden Schutz.

11. Das Gert muss jederzeit mit intaktem Schutzleiter an das Stromnetz angeschlossen sein.

12. Sollte der Hauptnetzstecker oder eine Gertesteckdose die Funktionseinheit zum Abschalten sein, muss diese immer zugnglich sein.

13. Verwenden Sie nur Zusatzgerte/Zubehrteile, die laut Hersteller geeignet sind.

14. Verwenden Sie nur Wagen, Standvorrichtungen, Stative, Halter oder Tische, die vom Hersteller benannt oder im Lieferumfang des Gerts enthalten sind. Falls Sie einen

Wagen benutzen, seien Sie vorsichtig beim Bewegen der Wagen- Gertkombination, um Verletzungen durch Stolpern zu vermeiden.

15. Ziehen Sie den Netzstecker bei Gewitter oder wenn Sie das Gert lngere Zeit nicht benutzen.

16. Lassen Sie alle Wartungsarbeiten nur von qualifiziertem Service-Personal ausfhren. Eine Wartung ist notwendig, wenn das Gert in irgendeiner Weise beschdigt wurde (z. B. Beschdigung des Netzkabels oder Steckers), Gegenstnde oder Flssigkeit in das Gerteinnere gelangt sind, das Gert Regen oder Feuchtigkeit ausgesetzt wurde, das Gert nicht ordnungsgem funktioniert oder auf den Boden gefallen ist.

17. Korrekte Entsorgung dieses Produkts: Dieses Symbol weist darauf hin, das Produkt entsprechend der WEEE Direktive (2012/19/EU) und der jeweiligen nationalen Gesetze nicht zusammen mit

Ihren Haushaltsabfllen zu entsorgen. Dieses Produkt sollte bei einer autorisierten Sammelstelle fr Recycling elektrischer und elektronischer Gerte (EEE) abgegeben werden. Wegen bedenklicher Substanzen, die generell mit elektrischen und elektronischen Gerten in Verbindung stehen, knnte eine unsachgeme Behandlung dieser Abfallart eine negative Auswirkung auf Umwelt und Gesundheit haben. Gleichzeitig gewhrleistet Ihr Beitrag zur richtigen Entsorgung dieses Produkts die effektive Nutzung natrlicher Ressourcen. Fr weitere Informationen zur Entsorgung Ihrer Gerte bei einer Recycling-Stelle nehmen Sie bitte Kontakt zum zustndigen stdtischen Bro, Entsorgungsamt oder zu Ihrem Haushaltsabfallentsorger auf.

18. Installieren Sie das Gert nicht in einer beengten Umgebung, zum Beispiel Bcherregal oder hnliches.

19. Stellen Sie keine Gegenstnde mit offenen Flammen, etwa brennende Kerzen, auf das Gert.

20. Beachten Sie bei der Entsorgung von Batterien den Umweltschutz-Aspekt. Batterien mssen bei einer Batterie-Sammelstelle entsorgt werden.

21. Dieses Gert ist in tropischen und gemigten Klimazonen bis 45 C einsetzbar.

Music Tribe bernimmt keine Haftung fr Verluste, die Personen entstanden sind, die sich ganz oder teilweise auf hier enthaltene Beschreibungen, Fotos oder Aussagen verlassen haben. Technische Daten, Erscheinungsbild und andere Informationen knnen ohne vorherige Ankndigung gendert werden. Alle Warenzeichen sind Eigentum der jeweiligen Inhaber. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones und Coolaudio sind Warenzeichen oder eingetragene Warenzeichen der Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 Alle Rechte vorbehalten.

Die geltenden Garantiebedingungen und zustzliche Informationen bezglich der von Music Tribe gewhrten beschrnkten Garantie finden Sie online unter community.musictribe.com/pages/support#warranty.

Les points reprs par ce symbole portent une tension lectrique suffisante pour constituer un risque dlectrocution.

Utilisez uniquement des cbles denceintes professionnels de haute qualit avec fiches Jack mono 6,35 mm ou fiches verrouillages dj installes. Toute autre installation ou modification doit tre effectue uniquement par un personnel qualifi.

Ce symbole avertit de la prsence dune tension dangereuse et non isole lintrieur de lappareil - elle peut

provoquer des chocs lectriques.

Attention Ce symbol signale les consignes dutilisation et dentre ! Tien importantes

dans la documentation fournie. Lisez les consignes de scurit du manuel dutilisation de lappareil.

Attention Pour viter tout risque de choc lectrique, ne pas ouvrir le capot de lappareil ni

dmonter le panneau arrire. Lintrieur de lappareil ne possde aucun lment rparable par lutilisateur. Laisser toute rparation un professionnel qualifi.

Attention Pour rduire les risques de feu et de choc lectrique, nexposez pas cet appareil la

pluie, la moisissure, aux gouttes ou aux claboussures. Ne posez pas de rcipient contenant un liquide sur lappareil (un vase par exemple).

Attention Ces consignes de scurit et dentretien sont destines un personnel qualifi.

Pour viter tout risque de choc lectrique, neffectuez aucune rparation sur lappareil qui ne soit dcrite par le manuel dutilisation. Les ventuelles rparations doivent tre effectues uniquement par un technicien spcialis.

1. Lisez ces consignes.

2. Conservez ces consignes.

3. Respectez tous les avertissements.

4. Respectez toutes les consignes dutilisation.

5. Nutilisez jamais lappareil proximit dun liquide.

6. Nettoyez lappareil avec un chiffon sec.

7. Veillez ne pas empcher la bonne ventilation de lappareil via ses oues de ventilation. Respectez les consignes du fabricant concernant linstallation de lappareil.

8. Ne placez pas lappareil proximit dune source de chaleur telle quun chauffage, une cuisinire ou tout appareil dgageant de la chaleur (y compris un ampli de puissance).

9. Ne supprimez jamais la scurit des prises bipolaires ou des prises terre. Les prises bipolaires possdent deux contacts de largeur diffrente. Le plus large est le contact de scurit. Les prises terre possdent deux contacts plus une mise la terre servant de scurit. Si la prise du bloc dalimentation ou du cordon dali-mentation fourni ne correspond pas celles de votre installation lectrique, faites appel un lectricien pour effectuer le changement de prise.

10. Installez le cordon dalimentation de telle faon que personne ne puisse marcher dessus et quil soit protg dartes coupantes. Assurez-vous que le cordon dalimentation est suffisamment protg, notamment au niveau de sa prise lectrique et de lendroit o il est reli lappareil; cela est galement valable pour une ventuelle rallonge lectrique.

11. Utilisez exclusivement des accessoires et des appareils supplmentaires recommands par le fabricant.

12. Utilisez exclusivement des chariots, des diables, des prsentoirs, des pieds et des surfaces de travail recommands par le fabricant ou livrs avec le produit.

Dplacez prcautionneusement tout chariot ou diable charg pour viter dventuelles blessures en cas de chute.

13. Dbranchez lappareil de la tension secteur en cas dorage ou si lappareil reste inutilis pendant une longue priode de temps.

14. Les travaux dentretien de lappareil doivent tre effectus uniquement par du personnel qualifi. Aucun entretien nest ncessaire sauf si lappareil est endommag de quelque faon que ce soit (dommages sur le cordon dalimentation ou la prise par exemple), si un liquide ou un objet a pntr lintrieur du chssis, si lappareil a t expos la pluie ou lhumidit, sil ne fonctionne pas correctement ou la suite dune chute.

15. Lappareil doit tre connect une prise secteur dote dune protection par mise la terre.

16. La prise lectrique ou la prise IEC de tout appareil dnu de bouton marche/arrt doit rester accessible en permanence.

17. Mise au rebut approprie de ce produit: Ce symbole indique quen accord avec la directive DEEE (2012/19/EU) et les lois en vigueur dans votre pays, ce produit ne doit pas tre jet avec les dchets mnagers. Ce produit doit tre

dpos dans un point de collecte agr pour le recyclage des dchets dquipements lectriques et lectroniques (EEE). Une mauvaise manipulation de ce type de dchets pourrait avoir un impact ngatif sur lenvironnement et la sant cause des substances potentiellement

dangereuses gnralement associes ces quipements. En mme temps, votre coopration dans la mise au rebut de ce produit contribuera lutilisation efficace des ressources naturelles. Pour plus dinformations sur lendroit o vous pouvez dposer vos dchets dquipements pour le recyclage, veuillez contacter votre mairie ou votre centre local de collecte des dchets.

18. Ninstallez pas lappareil dans un espace confin tel quune bibliothque ou meuble similaire.

19. Ne placez jamais dobjets enflamms, tels que des bougies allumes, sur lappareil.

20. Gardez lesprit limpact environnemental lorsque vous mettez des piles au rebus. Les piles uses doivent tre dposes dans un point de collecte adapt.

21. Cet appareil peut tre utilis sous un climat tropical ou modr avec des tempratures de 45C maximum.

Music Tribe ne peut tre tenu pour responsable pour toute perte pouvant tre subie par toute personne se fiant en partie ou en totalit toute description, photographie ou affirmation contenue dans ce document. Les caractristiques, lapparence et dautres informations peuvent faire lobjet de modifications sans notification. Toutes les marques appartiennent leurs propritaires respectifs. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones et Coolaudio sont des marques ou marques dposes de Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 Tous droits rservs.

Pour connatre les termes et conditions de garantie applicables, ainsi que les informations supplmentaires et dtailles sur la Garantie Limite de Music Tribe, consultez le site Internet community.musictribe.com/pages/support#warranty.

Consignes de scurit

DNI LGAL

Wichtige Sicherheitshinweise

HAFTUNGSAUSSCHLUSS

BESCHRNKTE GARANTIE

GARANTIE LIMITE

6 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 7

Attenzione I terminali contrassegnati da questo simbolo conducono una corrente elettrica

di magnitudine sufficiente a costituire un rischio di scossa elettrica. Utilizzare solo cavi per altoparlanti professionali di alta qualit con jack sbilanciati da 6,35mm. o connettori con blocco a rotazione. Tutte le altre installazioni o modifiche devono essere eseguite esclusivamente da personale qualificato.

Attenzione Questo simbolo, ovunque appaia, avverte della presenza di una tensione pericolosa

non isolata all'interno dello chassis, tensione che pu essere sufficiente per costituire un rischio di scossa elettrica.

Attenzione Questo simbolo, ovunque appaia, segnala importanti istruzioni operative e di

manutenzione nella documentazione allegata. Si invita a leggere il manuale.

Attenzione Per ridurre il rischio di scosse elettriche, non rimuovere il coperchio superiore

(o la sezione posteriore). All'interno non ci sono parti riparabili dall'utente. Per la manutenzione rivolgersi a personale qualificato.

Attenzione Per ridurre il rischio di incendi o scosse elettriche, non esporre questo apparecchio

a pioggia e umidit. L'apparecchio non deve essere esposto a gocciolio o schizzi di liquidi e nessun oggetto contenente liquidi, come vasi, deve essere collocato sull'apparecchio.

Attenzione Queste istruzioni di servizio sono destinate esclusivamente a personale qualificato.

Per ridurre il rischio di scosse elettriche non eseguire interventi di manutenzione diversi da quelli contenuti nel manuale di istruzioni. Le riparazioni devono essere eseguite da personale di assistenza qualificato.

1. Leggere queste istruzioni.

2. Conservare queste istruzioni.

3. Prestare attenzione a tutti gli avvisi.

4. Applicare tutte le istruzioni.

5. Non utilizzare questo dispositivo vicino l'acqua.

6. Pulire esclusivamente con un panno asciutto.

7. Non bloccare le aperture di ventilazione. Installare in conformit con le istruzioni del produttore.

8. Non installare vicino a fonti di calore come radiatori, termoregolatori, stufe o altri apparecchi (inclusi amplificatori) che producono calore.

9. Non escludere la sicurezza fornita dalla spina polarizzata o con messa a terra. Una spina polarizzata ha due lame, una pi larga dell'altra. Una spina con messa a terra ha due lame e un terzo polo di messa a terra. La lama larga o il terzo polo sono forniti per la vostra sicurezza. Se la spina fornita non si adatta alla presa, consultare un elettricista per la sostituzione della presa obsoleta.

10. Proteggere il cavo di alimentazione dal calpestio o essere schiacciato in particolare alle spine, prese di corrente e il punto in cui esce dall'apparecchio.

11. Utilizzare esclusivamente dispositivi/accessori specificati dal produttore.

12. Utilizzare solo carrelli, supporti, treppiedi, staffe o tavoli indicati dal produttore o venduti con l'apparecchio. Utilizzando un carrello, prestare attenzione quando si sposta la combinazione

carrello/apparecchio per evitare lesioni dovute al ribaltamento.

13. Scollegare questo apparecchio durante i temporali o se non utilizzato per lunghi periodi di tempo.

14. Per tutte le riparazioni rivolgersi a personale qualificato. La manutenzione necessaria quando l'apparecchio danneggiato in qualsiasi modo, come danneggiamento del cavo di alimentazione o della spina, versamento di liquido o oggetti caduti nell'apparecchio, se l'apparecchio stato esposto a pioggia o umidit, se non funziona normalmente o caduto.

15. L'apparecchio deve essere collegato a una presa di corrente elettrica con messa a terra di protezione.

16. Se la spina o una presa del dispositivo utilizzata come dispositivo di disconnessione, deve essere facilmente utilizzabile.

17. Smaltimento corretto di questo prodotto: questo simbolo indica che questo dispositivo non deve essere smaltito insieme ai rifiuti domestici, secondo la Direttiva RAEE (2012/19 / UE) e la vostra legislazione

nazionale. Questo prodotto deve essere portato in un centro di raccolta autorizzato per il riciclaggio di rifiuti di apparecchiature elettriche ed elettroniche (RAEE). La cattiva gestione di questo tipo di rifiuti potrebbe avere un possibile impatto negativo sull'ambiente e sulla salute umana a causa di sostanze potenzialmente pericolose che sono generalmente associate alle apparecchiature elettriche ed elettroniche. Nello stesso tempo la vostra collaborazione al corretto smaltimento di questo prodotto contribuir all'utilizzo efficiente delle risorse naturali. Per ulteriori informazioni su dove possibile trasportare le apparecchiature per il riciclaggio vi invitiamo a contattare l'ufficio comunale locale o il servizio di raccolta dei rifiuti domestici.

18. Non installare in uno spazio ristretto, come in una libreria o in una struttura simile.

19. Non collocare sul dispositivo fonti di fiamme libere, come candele accese.

20. Per lo smaltimento delle batterie, tenere in considerazione gli aspetti ambientali. Le batterie devono essere smaltite in un punto di raccolta delle batterie esauste.

21. Questo apparecchio pu essere usato in climi tropicali e temperati fino a 45C.

Music Tribe non si assume alcuna responsabilit per eventuali danni che possono essere subiti da chiunque si affidi in tutto o in parte a qualsiasi descrizione, fotografia o dichiarazione contenuta qui. Specifiche tecniche, aspetti e altre informazioni sono soggette a modifiche senza preavviso. Tutti i marchi sono di propriet dei rispettivi titolari. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones e Coolaudio sono marchi o marchi registrati di Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 Tutti i diritti riservati .

Per i termini e le condizioni di garanzia applicabili e le informazioni aggiuntive relative alla garanzia limitata di Music Tribe, consultare online i dettagli completi su community.musictribe.com/pages/support#warranty.

Informazioni importanti

DISCLAIMER LEGALE

GARANZIA LIMITATA

Aviso! Terminais marcados com o smbolo carregam corrente eltrica de magnitude

suficiente para constituir um risco de choque eltrico. Use apenas cabos de alto-falantes de alta qualidade com plugues TS de " ou plugues com trava de toro pr-instalados. Todas as outras instalaes e modificaes devem ser efetuadas por pessoas qualificadas.

Este smbolo, onde quer que o encontre, alerta-o para a leitura das instrues de manuseamento que acompanham o

equipamento. Por favor leia o manual de instrues.

Ateno De forma a diminuir o risco de choque elctrico, no remover a cobertura

(ou a seco de trs). No existem peas substituveis por parte do utilizador no seu interior. Para esse efeito recorrer a um tcnico qualificado.

Ateno Para reduzir o risco de incndios ou choques elctricos o aparelho no deve ser

exposto chuva nem humidade. Alm disso, no deve ser sujeito a salpicos, nem devem ser colocados em cima do aparelho objectos contendo lquidos, tais como jarras.

Ateno Estas instrues de operao devem ser utilizadas, em exclusivo, por tcnicos de

assistncia qualificados. Para evitar choques elctricos no proceda a reparaes ou intervenes, que no as indicadas nas instrues de operao, salvo se possuir as qualifi-caes necessrias. Para evitar choques elctricos no proceda a reparaes ou intervenes, que no as indicadas nas instrues de operao. S o dever fazer se possuir as qualificaes necessrias.

1. Leia estas instrues.

2. Guarde estas instrues.

3. Preste ateno a todos os avisos.

4. Siga todas as instrues.

5. No utilize este dispositivo perto de gua.

6. Limpe apenas com um pano seco.

7. No obstrua as entradas de ventilao. Instale de acordo com as instrues do fabricante.

8. No instale perto de quaisquer fontes de calor tais como radiadores, bocas de ar quente, foges de sala ou outros aparelhos (incluindo amplificadores) que produzam calor.

9. No anule o objectivo de segurana das fichas polarizadas ou do tipo de ligao terra. Uma ficha polarizada dispe de duas palhetas sendo uma mais larga do que a outra. Uma ficha do tipo ligao terra dispe

de duas palhetas e um terceiro dente de ligao terra. A palheta larga ou o terceiro dente so fornecidos para sua segurana. Se a ficha fornecida no encaixar na sua tomada, consulte um electricista para a substituio da tomada obsoleta.

10. Proteja o cabo de alimentao de pisadelas ou apertos, especialmente nas fichas, extenses, e no local de sada da unidade. Certifique-se de que o cabo elctrico est protegido. Verifique particularmente nas fichas, nos receptculos e no ponto em que o cabo sai do aparelho.

11. O aparelho tem de estar sempre conectado rede elctrica com o condutor de proteco intacto.

12. Se utilizar uma ficha de rede principal ou uma tomada de aparelhos para desligar a unidade de funcionamento, esta deve estar sempre acessvel.

13. Utilize apenas ligaes/acessrios especificados pelo fabricante.

14. Utilize apenas com o carrinho, estrutura, trip, suporte, ou mesa especificados pelo fabricante ou vendidos com o dispositivo. Quando utilizar um carrinho, tenha cuidado ao

mover o conjunto carrinho/dispositivo para evitar danos provocados pela terpidao.

15. Desligue este dispositivo durante as trovoadas ou quando no for utilizado durante longos perodos de tempo.

16. Qualquer tipo de reparao deve ser sempre efectuado por pessoal qualificado. necessria uma reparao sempre que a unidade tiver sido de alguma forma danificada, como por exemplo: no caso do cabo de alimentao ou ficha se encontrarem danificados; na eventualidade de lquido ter sido derramado ou objectos terem cado para dentro do dispositivo; no caso da unidade ter estado exposta chuva ou humidade; se esta no funcionar normalmente, ou se tiver cado.

17. Correcta eliminao deste produto: este smbolo indica que o produto no deve ser eliminado juntamente com os resduos domsticos, segundo a Directiva REEE (2012/19/EU) e a legislao nacional. Este produto dever

ser levado para um centro de recolha licenciado para a reciclagem de resduos de equipamentos elctricos e electrnicos (EEE). O tratamento incorrecto deste tipo de resduos pode ter um eventual impacto negativo no ambiente e na sade humana devido a substncias potencialmente perigosas que esto geralmente associadas aos EEE. Ao mesmo tempo, a sua colaborao para a eliminao correcta deste produto ir contribuir para a utilizao eficiente dos recursos naturais. Para mais informao acerca dos locais onde poder deixar o seu equipamento usado para reciclagem, favor contactar os servios municipais locais, a entidade de gesto de resduos ou os servios de recolha de resduos domsticos.

18. No instale em lugares confinados, tais como estantes ou unidades similares.

19. No coloque fontes de chama, tais como velas acesas, sobre o aparelho.

20. Favor, obedecer os aspectos ambientais de descarte de bateria. Baterias devem ser descartadas em um ponto de coletas de baterias.

21. Esse aparelho pode ser usado em climas tropicais e moderados at 45C.

O Music Tribe no se responsabiliza por perda alguma que possa ser sofrida por qualquer pessoa que dependa, seja de maneira completa ou parcial, de qualquer descrio, fotografia, ou declarao aqui contidas. Dados tcnicos, aparncias e outras informaes esto sujeitas a modificaes sem aviso prvio. Todas as marcas so propriedade de seus respectivos donos. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones e Coolaudio so marcas ou marcas registradas do Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 Todos direitos reservados.

Para obter os termos de garantia aplicveis e condies e informaes adicionais a respeito da garantia limitada do Music Tribe, favor verificar detalhes na ntegra atravs do website community.musictribe.com/pages/ support#warranty.

Instrues de Segurana Importantes

LEGAL RENUNCIANTE

GARANTIA LIMITADA

8 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 9

Waarschuwing Aansluitingen die gemerkt zijn met het symbool voeren een zodanig hoge

spanning dat ze een risico vormen voor elektrische schokken. Gebruik uitsluitend kwalitatief hoogwaardige, in de handel verkrijgbare luidsprekerkabels die voorzien zijn van " TS stekkers. Laat uitsluitend gekwalificeerd personeel alle overige installatie- of modificatiehandelingen uitvoeren.

Dit symbool wijst u altijd op belangrijke bedienings - en onderhoudsvoorschriften in de bijbehorende documenten.

Wij vragen u dringend de handleiding te lezen.

Attentie Verwijder in geen geval de bovenste afdekking (van het achterste gedeelte)

anders bestaat er gevaar voor een elektrische schok. Het apparaat bevat geen te onderhouden onderdelen. Reparatiewerkzaamheden mogen uitsluitend door gekwalificeerd personeel uitgevoerd worden.

Attentie Om het risico op brand of elektrische schokken te beperken, dient u te

voorkomen dat dit apparaat wordt blootgesteld aan regen en vocht. Het apparaat mag niet worden blootgesteld aan neerdruppelend of opspattend water en er mogen geen met water gevulde voorwerpen zoals een vaas op het apparaat worden gezet.

Attentie Deze onderhoudsinstructies zijn uitsluitend bedoeld voor gekwalificeerd

onderhoudspersoneel. Om elektrische schokken te voorkomen, mag u geen andere onderhoudshandelingen verrichten dan in de bedieningsinstructies vermeld staan. Reparatiewerkzaamheden mogen alleen uitgevoerd worden door gekwalificeerd onderhoudspersoneel.

1. Lees deze voorschriften.

2. Bewaar deze voorschriften.

3. Neem alle waarschuwingen in acht.

4. Volg alle voorschriften op.

5. Gebruik dit apparaat niet in de buurt van water.

6. Reinig het uitsluitend met een droge doek.

7. Let erop geen van de ventilatie-openingen te bedekken. Plaats en installeer het volgens de voor- schriften van de fabrikant.

8. Het apparaat mag niet worden geplaatst in de buurt van radiatoren, warmte-uitlaten, kachels of andere zaken (ook versterkers) die warmte afgeven.

9. Maak de veiligheid waarin door de polarisatie- of aardingsstekker wordt voorzien, niet ongedaan. Een polarisatiestekker heeft twee bladen, waarvan er een breder is dan het andere. Een aardingsstekker heeft twee bladen en een derde uitsteeksel voor de aarding. Het bredere blad of het derde uitsteeksel zijn er voor uw veiligheid. Mocht de geleverde stekker niet in uw stopcontact passen, laat het contact dan door een elektricien vervangen.

10. Om beschadiging te voorkomen, moet de stroomleiding zo gelegd worden dat er niet kan worden over gelopen en dat ze beschermd is tegen scherpe kanten. Zorg zeker voor voldoende bescherming aan de stekkers, de verlengkabels en het punt waar het netsnoer het apparaat verlaat.

11. Het toestel met altijd met een intacte aarddraad aan het stroomnet aangesloten zijn.

12. Wanneer de stekker van het hoofdnetwerk of een apparaatstopcontact de functionele eenheid voor het uitschakelen is, dient deze altijd toegankelijk te zijn.

13. Gebruik uitsluitend door de producent gespeci- ficeerd toebehoren c.q. onderdelen.

14. Gebruik het apparaat uitsluitend in combinatie met de wagen, het statief, de driepoot, de beugel of tafel die door de producent is aangegeven, of die in combinatie met het apparaat wordt verkocht.

Bij gebruik van een wagen dient men voorzichtig te zijn bij het verrijden van de combinatie wagen/apparaat en letsel door vallen te voorkomen.

15. Bij onweer en als u het apparaat langere tijd niet gebruikt, haalt u de stekker uit het stopcontact.

16. Laat alle voorkomende reparaties door vakkundig en bevoegd personeel uitvoeren. Reparatiewerk-zaamheden zijn nodig als het toestel op enige wijze beschadigd is geraakt, bijvoorbeeld als de hoofd-stroomkabel of -stekker is beschadigd, als er vloeistof of voorwerpen in terecht zijn gekomen, als het aan regen of vochtigheid heeft bloot-gestaan, niet normaal functioneert of wanneer het is gevallen.

17. Correcte afvoer van dit product: dit symbool geeft aan dat u dit product op grond van de AEEA-richtlijn (2012/19/EU) en de nationale wetgeving van uw land niet met het gewone huishoudelijke afval mag

weggooien. Dit product moet na afloop van de nuttige levensduur naar een officile inzamelpost voor afgedankte elektrische en elektronische apparatuur (AEEA) worden gebracht, zodat het kan worden gerecycleerd. Vanwege de potentieel gevaarlijke stoffen die in elektrische en elektronische apparatuur kunnen voorkomen, kan een onjuiste afvoer van afval van het onderhavige type een negatieve invloed op het milieu en de menselijke gezondheid hebben. Een juiste afvoer van dit product is echter niet alleen beter voor het milieu en de gezondheid, maar draagt tevens bij aan een doelmatiger gebruik

van de natuurlijke hulpbronnen. Voor meer informatie over de plaatsen waar u uw afgedankte apparatuur kunt inleveren, kunt u contact opnemen met uw gemeente of de plaatselijke reinigingsdienst.

18. Installeer niet in een kleine ruimte, zoals een boekenkast of iets dergelijks.

19. Plaats geen open vlammen, zoals brandende kaarsen, op het apparaat.

20. Houd rekening met de milieuaspecten van het afvoeren van batterijen. Batterijen moeten bij een inzamelpunt voor batterijen worden ingeleverd.

21. Dit apparaat kan worden gebruikt in tropische en gematigde klimaten tot 45 C.

Music Tribe aanvaardt geen aansprakelijkheid voor enig verlies dat kan worden geleden door een persoon die geheel of gedeeltelijk vertrouwt op enige beschrijving, foto of verklaring hierin. Technische specificaties, verschijningen en andere informatie kunnen zonder voorafgaande kennisgeving worden gewijzigd. Alle handelsmerken zijn eigendom van hun respectievelijke eigenaren. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones en Coolaudio zijn handelsmerken of gedeponeerde handelsmerken van Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 Alle rechten voorbehouden.

Voor de toepasselijke garantievoorwaarden en aanvullende informatie met betrekking tot de beperkte garantie van Music Tribe, zie de volledige details online op community.musictribe.com/pages/ support#warranty.

Belangrijke veiligheidsvoorschriften

Varning Uttag markerade med symbolen leder elektrisk strmstyrka som r tillrckligt

stark fr att utgra en risk fr elchock. Anvnd endast hgkvalitativa, kommersiellt tillgngliga hgtalarkablar med frhandsinstallerade " TS-kontakter. All annan installering eller modifikation br endast utfras av kompetent personal.

Den hr symbolen hnvisar till viktiga punkter om anvndning och underhll i den medflljande dokumentationen.

Var vnlig och ls bruksanvisningen.

Frsiktighet Minska risken fr elektriska sttar genom att aldrig ta av hljet upptill p apparaten

(eller ta av baksidan). Inuti apparaten finns det inga delar som kan repareras av anvndaren. Endast kvalificerad personal fr genomfra reparationer.

Frsiktighet Fr att minska risken fr brand och elektriska sttar ska apparaten skyddas

mot regn och fukt. Apparaten gr inte utsttas fr dropp eller spill och inga vattenbehllare som vaser etc. fr placeras p den.

Frsiktighet Serviceinstruktionen r enbart avsedd fr kvalificerad servicepersonal. Fr att

undvika risker genom elektriska sttar, genomfr inga reparationer p apparaten, vilka inte r beskrivna i bruksanvisningen. Endast kvalificerad fackpersonal fr genomfra reparationerna.

1. Ls dessa anvisningar.

2. Spara dessa anvisningar.

3. Beakta alla varningar.

4. Flj alla anvisningar.

5. Anvnd inte apparaten i nrheten av vatten.

6. Rengr endast med torr trasa.

7. Blockera inte ventilationsppningarna. Installera enligt tillverkarens anvisningar.

8. Installera aldrig intill vrmekllor som vrme- element, varmluftsintag, spisar eller annan utrustning som avger vrme (inklusive frstrkare).

9. ndra aldrig en polariserad eller jordad kontakt. En polariserad kontakt har tv blad det ena bredare n det andra. En jordad kontakt har tv blad och ett tredje jordstift. Det breda bladet eller jordstiftet r till fr din skerhet. Om den medfljande kontakten inte passar i ditt uttag, ska du kontakta en elektriker fr att f uttaget bytt.

10. Frlgg elkabeln s, att det inte r mjligt att trampa p den och att den r skyddad mot skarpa kanter och inte kan skadas. Ge i synnerhet akt p omrdena omkring stickkontakterna, frlngningskablarna och p det stlle, dr elkabeln lmnar apparaten, r tillrckligt skyddade.

11. Apparaten mste alltid vara ansluten till elntet med intakt skyddsledare.

12. Om huvudkontakten, eller ett apparatuttag, fungerar som avstngningsenhet mste denna alltid vara tillgnglig.

13. Anvnd endast tillkopplingar och tillbehr som angetts av tillverkaren.

14. Anvnd endast med vagn, stativ, trefot, hllare eller bord som angetts av tillverkaren, eller som slts till- sammans med apparaten. Om du anvnder en vagn, var frsiktig, nr du

frflyttar kombinationen vagn-apparat, fr att frhindra olycksfall genom snubbling.

15. Dra ur anslutningskontakten und skvder eller nr apparaten inte ska anvndas under ngon lngre tid.

16. Lt kvalificerad personal utfra all service. Service r ndvndig nr apparaten har skadats, t.ex. nr en elkabel eller kontakt r skadad, vtska eller frmmande freml har kommit in i apparaten, eller nr den har fallit i golvet.

17. Kassera produkten p rtt stt: den hr symbolen indikerar att produkten inte ska kastas i hushllssoporna, enligt WEEE direktivet (2012/19/EU) och gllande, nationell lagstiftning. Produkten ska lmnas till ett

auktoriserat tervinningsstlle fr elektronisk och elektrisk utrustning (EEE). Om den hr sortens avfall hanteras p fel stt kan miljn, och mnniskors hlsa, pverkas negativt p grund av potentiella risksubstanser som ofta associeras med EEE. Avfallshanteras produkten dremot p rtt stt bidrar detta till att naturens resurser anvnds p ett bra stt. Kontakta kommun, ansvarig frvaltning eller avfallshanteringsfretag fr mer information om tervinningscentral dr produkten kan lmnas

18. Installera inte i ett trngt utrymme, t.ex. i en bokhylsa eller liknande enhet.

19. Placera inte kllor med ppen eld, t.ex. tnda ljus, p apparaten.

20. Tnk p miljaspekterna vid kassering av batterier. Batterier mste kasseras p ett batteriuppsamlingsstlle.

21. Denna apparat kan anvndas i tropiska och mttliga klimat upp till 45 C.

Music Tribe tar inget ansvar fr ngon frlust som kan drabbas av ngon person som helt eller delvis frlitar sig p ngon beskrivning, fotografi eller uttalande som finns hr. Tekniska specifikationer, utseenden och annan information kan ndras utan fregende meddelande. Alla varumrken tillhr respektive gare. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones och Coolaudio r varumrken eller registrerade varumrken som tillhr Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 Alla Rttigheter reserverade.

Fr tillmpliga garantivillkor och ytterligare information om Music Tribes begrnsade garanti, se fullstndig information online p community.musictribe.com/ pages/support#warranty.

Viktiga skerhetsanvisningar

BEGRNSAD GARANTI

FRISKRIVNINGSKLAUSUL

WETTELIJKE ONTKENNING

BEPERKTE GARANTIE

10 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 11

Uwaga Terminale oznaczone symbolem przenosz wystarczajco wysokie

napicie elektryczne, aby stworzy ryzyko poraenia prdem. Uywaj wycznie wysokiej jakoci fabrycznie przygotowanych kabli z zainstalowanymi wtyczkami " TS. Wszystkie inne instalacje lub modyfikacje powinny by wykonywane wycznie przez wykwalifikowany personel techniczny.

Ten symbol informuje o wanych wskazwkach dotyczcych obsugi i konserwacji urzdzenia w doczonej

dokumentacji. Prosz przeczyta stosowne informacje w instrukcji obsugi.

Uwaga W celu wyeliminowania zagroenia poraenia prdem zabrania si

zdejmowania obudowy lub tylnej cianki urzdzenia. Elementy znajdujce si we wntrzu urzdzenia nie mog by naprawiane przez uytkownika. Naprawy mog by wykonywane jedynie przez wykwalifikowany personel.

Uwaga W celu wyeliminowania zagroenia poraenia prdem lub zapalenia si

urzdzenia nie wolno wystawia go na dziaanie deszczu i wilgotnoci oraz dopuszcza do tego, aby do wntrza dostaa si woda lub inna ciecz. Nie naley stawia na urzdzeniu napenionych ciecz przedmiotw takich jak np. wazony lub szklanki.

Uwaga Prace serwisowe mog by wykonywane jedynie przez wykwalifikowany personel.

W celu uniknicia zagroenia poraenia prdem nie naley wykonywa adnych manipulacji, ktre nie s opisane w instrukcji obsugi. Naprawy wykonywane mog by jedynie przez wykwalifikowany personel techniczny.

1. Prosz przeczyta ponisze wskazwki.

2. Prosz przechowywa niniejsz instrukcj.

3. Naley przestrzega wszystkich wskazwek ostrzegawczych.

4. Naley postpowa zgodnie z instrukcj obsugi.

5. Urzdzenia nie wolno uywa w pobliu wody.

6. Urzdzenie mona czyci wycznie such szmatk.

7. Nie zasania otworw wentylacyjnych. W czasie podczania urzdzenia naley przestrzega zalece producenta.

8. Nie stawia urzdzenia w pobliu rde ciepa takich, jak grzejniki, piece lub urzdzenia produkujce ciepo (np. wzmacniacze).

9. W adnym wypadku nie naley usuwa zabezpiecze z wtyczek dwubiegunowych oraz wtyczek z uziemieniem. Wtyczka dwubiegunowa posiada dwa wtyki kontaktowe o rnej szerokoci. Wtyczka z uziemieniem ma dwa wtyki kontaktowe i trzeci wtyk uziemienia. Szerszy wtyk kontaktowy lub dodatkowy wtyk uziemienia su do zapewnienia bezpieczestwa uytkownikowi. Jeli format wtyczki urzdzenia nie odpowiada standardowi gniazdka, prosz zwrci si do elektryka z prob o wymienienie gniazda.

10. Kabel sieciowy naley uoy tak, aby nie by naraony na deptanie i dziaanie ostrych krawdzi, co mogoby doprowadzi do jego uszkodzenia. Szczegln uwag zwrci naley na odpowiedni ochron miejsc w pobliu wtyczek i przeduaczy oraz miejsce, w ktrym kabel sieciowy przymocowany jest do urzdzenia.

11. Urzdzenie musi by zawsze podczone do sieci sprawnym przewodem z uziemieniem.

12. Jeeli wtyk sieciowy lub gniazdo sieciowe w urzdzeniu peni funkcj wycznika, to musz one by zawsze atwo dostpne.

13. Uywa wycznie sprztu dodatkowego i akcesoriw zgodnie z zaleceniami producenta.

14. Uywa jedynie zalecanych przez producenta lub znajdujcych si w zestawie wzkw, stojakw, statyww, uchwytw i stow. W przypadku

posugiwania si wzkiem naley zachowa szczegln ostrono w trakcie przewoenia zestawu, aby unikn niebezpieczestwa potknicia si i zranienia.

15. W trakcie burzy oraz na czas duszego nieuywania urzdzenia naley wyj wtyczk z gniazdka sieciowego.

16. Wykonywanie wszelkich napraw naley zleca jedynie wykwalifikowanym pracownikom serwisu. Przeprowadzenie przegldu technicznego staje si konieczne, jeli urzdzenie zostao uszkodzone w jakikolwiek sposb (dotyczy to take kabla sieciowego lub wtyczki), jeli do wntrza urzdzenia dostay si przedmioty lub ciecz, jeli urzdzenie wystawione byo na dziaanie deszczu lub wilgoci, jeli urzdzenie nie funkcjonuje poprawnie oraz kiedy spado na podog.

17. Prawidowa utylizacja produktu: Ten symbol wskazuje, e tego produktu nie naley wyrzuca razem ze zwykymi odpadami domowymi, tylko zgodnie z dyrektyw w sprawie zuytego sprztu

elektrycznego i elektronicznego (WEEE) (2012/19/EU) oraz przepisami krajowymi. Niniejszy produkt naley przekaza do autoryzowanego punktu zbirki zuytego sprztu elektrycznego i elektronicznego. Niewaciwe postpowanie z tego typu odpadami moe wywoa szkodliwe dziaanie na rodowisko naturalnej i

zdrowie czowieka z powodu potencjalnych substancji niebezpiecznych zaliczanych jako zuyty sprzt elektryczny i elektroniczny. Jednoczenie, Twj wkad w prawidow utylizacj niniejszego produktu przyczynia si do oszczdnego wykorzystywania zasobw naturalnych. Szczegowych informacji o miejscach, w ktrych mona oddawa zuyty sprzt do recyklingu, udzielaj urzdy miejskie, przedsibiorstwa utylizacji odpadw lub najbliszy zakad utylizacji odpadw.

18. Nie instaluj w ograniczonej przestrzeni, takiej jak pka na ksiki lub podobny zestaw.

19. Nie stawiaj na urzdzeniu rde otwartego ognia, takich jak zapalone wiece.

20. Naley pamita o rodowiskowych aspektach utylizacji baterii. Baterie naley utylizowa w punkcie zbirki baterii.

21. To urzdzenie moe by uywane w klimacie tropikalnym i umiarkowanym do 45 C.

Music Tribe nie ponosi odpowiedzialnoci za jakiekolwiek straty, ktre mog ponie osoby, ktre polegaj w caoci lub w czci na jakimkolwiek opisie, fotografii lub owiadczeniu zawartym w niniejszym dokumencie. Specyfikacje techniczne, wygld i inne informacje mog ulec zmianie bez powiadomienia. Wszystkie znaki towarowe s wasnoci ich odpowiednich wacicieli. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones i Coolaudio s znakami towarowymi lub zastrzeonymi znakami towarowymi firmy Music Tribe Global Brands Ltd. Music Tribe Global Brands Ltd. 2021 Wszystkie prawa zastrzeone.

Aby zapozna si z obowizujcymi warunkami gwarancji i dodatkowymi informacjami dotyczcymi ograniczonej gwarancji Music Tribe, zapoznaj si ze wszystkimi szczegami w trybie online pod adresem community.musictribe.com/pages/support#warranty.

Wane informacje o bezpieczestwie

ZASTRZEENIA PRAWNE

OGRANICZONA GWARANCJA

12 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 13

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Hook-up

(EN) Step 2: Controls

(ES) Paso 2: Controles

(FR) Etape 2 : Rglages

(DE) Schritt 2: Bedienelemente

(PT) Passo 2: Controles

(IT) Passo 2: Controlli

(NL) Stap 2: Bediening

(SE) Steg 2: Kontroller

(PL) Krok 2: Sterowanica

Example of a setup using the ULTRATONE

Ejemplo de configuracin con el ULTRATONE

Exemple de configuration utilisant lULTRATONE

Beispiel-Setup mit dem ULTRATONE

Exemplo de configurao utilizando o ULTRATONE

Esempio di configurazione utilizzando ULTRATONE

Voorbeeld van een opstelling met behulp van de ULTRATONE

Exempel p en installation med ULTRATONE

Przykad konfiguracji przy uyciu ULTRATONE

Live setup

Configuracin para directo

Systme de live

Live-Setup

Configurao ao vivo

Configurazione dal vivo

Live opstelling

Live-installation

Konfiguracja na ywo

Footswitch

BEHRINGER ULTRATONE K900FX

HPS3000

Keyboard

CD In

Mic In

Line In Line In

Phones

Drum Computer

XM8500

MP3 Player Footswitch

BEHRINGER ULTRATONE K3000FX

HPS3000XM8500

Line In

X2222USB

EP2000

EP2000

Line Out

Main Outputs

Mic In 1

Phones

Line In 4 Line In 2Line In 3

Sub Out

B1800X PRO

B1520 PRO

Drum Computer

2 x Keyboard

14 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 15

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Controls

(EN) Step 2: Controls

(1) (3) (5) (6) (7) (9)

(2) (4) (8) (14)(12)(10)

(11) (13)

(15)

(25)(24)(19) (20)(18)(16)

(23)(22)(26)(17) (21)

(14)(12)(10)(8)

(9)(7)(6)(5)(1)

(2)

(16)(15) (22) (21) (19) (25)(23) (24)

16 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 17

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Controls

(EN) Step 2: Controls (ES) Paso 2: Controles

(1) The LEVEL controls adjust the signal level of channels 1 - 4 (K900FX and K450FX: channels 1 - 3).

(2) The four FX controls adjust the channel 1 - 4 signal level at the input of the integrated effects processor (K900FX and K450FX: three controls fo r channels 1 - 3).

(3) The channel 4 signal (K3000FX and K1800FX only) is normally routed just to the PHONES output without effects. This way you can practice without being heard, or you can connect a metronome that you need on headphones but not on speakers. By pressing the TO MAIN button the signal will be additionally routed to the speakers without effects.

(4) By pressing the TO LINE OUT button the channel 4 signal will be additionally routed to the LINE OUT output without effects (K3000FX and K1800FX only). If you press both the TO MAIN and TO LINE button, channel 4 will be equal to channels 1 - 3. The signal will be routed to the speakers and the LINE OUT output including effects.

(5) The ULTRATONE is equipped with a 7-band graphic equalizer (K900FX and K450FX: 5-band graphic equalizer). Use the EQ to adapt the sound to the room acoustics.

(6) Press the FBQ switch to activate the FBQ Feedback Detection System. The frequencies causing feedback are shown by the brightly lit fader LEDs. Simply lower the level of the respective frequency range until feedback disappears and the LED goes out.

(7) The FX display shows the currently selected preset. The SIG LED lights up when the effects processor receives an input signal. When the CLIP LED lights up please reduce the effects input signal by using the respective FX control(s) (2).

(8) Turn the FX control to select an effects preset (preset number starts flashing). Push the control briefly to confirm your selection.

(9) The LEVEL control in the master section is used to adjust the main output volume.

(10) Turn the FX RET control to add the effect signal to the main mix.

(11) Pressing the SHAPE button will add the Shape effect to the main signal. The Shape function on your ULTRATONE provides a revolutionary type of filter that you can use to modify your keyboard sound (K3000FX and K1800FX only).

(12) Use the PHONES jack to plug in your headphones.

(13) The PHONES LEVEL control adjusts the headphones output level (K3000FX and K1800FX only).

(14) Use the POWER switch to switch the ULTRATONE on or off. You should always make sure that the POWER switch is in the Off position when initially connecting the unit to the mains.

(15) MAINS CONNECTION. Use the power cord supplied with the unit to connect it to the mains.

(16) FUSE HOLDER/VOLTAGE SELECTOR. Before connecting the unit to the mains, make sure that the voltage setting matches your local voltage. A blown fuse should only be replaced by a fuse of the same type and rating. On some units, the fuse holder can be switched to one of two positions, i.e. 230 V and 120 V. When operating the unit outside Europe at 120 V, a higher fuse rating is required.

(17) The GROUND LIFT switch disconnects (switch pressed) the ground connection at the LINE OUT output to effectively eliminate hum noise resulting from ground loops (K3000FX and K1800FX only).

(18) Use the balanced LINE OUT XLR connectors to feed the audio signal from your ULTRATONE to a mixing console (K3000FX and K1800FX only). The LINE OUT signal is post-EQ.

(19) These are the LINE OUT outputs on 1/4" TS connectors (K900FX and K450FX: one 1/4" TS connector). Both XLR and 1/4" TS LINE OUT connectors can be used simultaneously.

(20) For stereo operation the ULTRATONE features a STEREO LINK facility. You can connect the OUT of the ULTRATONE to the LINK IN of another keyboard amp that serves as slave to achieve true stereo sound. When using the ULTRATONE as slave, connect the LINK OUT of the master amp to the IN (K3000FX and K1800FX only).

(21) The SUB OUT connector provides the line- level mono subwoofer signal for connection to the input of a power amp or active subwoofer.

(22) Connect your footswitch to the FOOT SW jack, so as to activate/deactivate the effects processor.

(23) Use the CD IN connectors to connect the output of your CD player, tape deck, or MP3 Player. This way you can play along to music or keyboard tutorial CDs.

(24) These are the LINE inputs for channels 1-4 (K3000FX/K1800FX) / channels 1-3 (K900FX/ K450FX) on " TS connectors. For mono input signals please use the L (MONO) connector.

(25) Channel 1 is equipped with an additional XLR MIC input. Due to internal +15 V phantom power you can even use condenser microphones. Both XLR and 1/4" TS connectors can be used simultaneously. In this case the LEVEL control of channel 1 adjusts both the level of the LINE and MIC signal.

(1) El control LEVEL regula el nivel de seal de los canales 1 - 4 (K900FX y K450FX: canales 1 - 3).

(2) Los cuatro controles FX regulan el nivel de la seal de entrada del procesador de efectos proveniente de los canales 1 - 4 (K900FX y K4500FX: tres controles para los canales 1 - 3).

(3) Por lo general, la seal del canal 4 (nicamente K3000FX y K1800FX) es asignada sin efectos a la salida de auriculares exclusivamente, lo que le permite practicar sin ser escucha-do o utilizar un metrnomo que slo sea escuchado a travs de los auriculares. Sin embargo, tambin puede asignar la seal sin efectos del canal 4 a los altavoces presionando el pulsador TO MAIN.

(4) El pulsador TO LINE OUT asigna la seal sin efectos del canal 4 a la salida LINE OUT (nicamente K3000FX y K1800FX). Si presiona ambos pulsadores TO MAIN y TO LINE, el canal 4 se comportar de la misma manera que los canales 1 - 3, es decir, la seal con efectos del canal 4 ser asignada a los altavoces y a la salida LINE OUT.

(5) El ULTRATONE est equipado con un ecualizador grfico de 7 bandas (K900FX y K450FX: ecualizador grfico de 5 bandas). ste le puede ser muy til para ajustar el sonido del amplificador a la acstica del lugar.

(6) FBQ activa el Sistema FBQ de Deteccin de Realimentacin, mediante el cual se indican las frecuencias que provocan realimentacin en los LEDs de los faders del ecualizador. Si se presenta el caso, simplemente debe bajar el nivel del rango de frecuencias indicado hasta que la realimentacin cese, el LED correspondiente se volver a apagar.

(7) La pantalla FX indica el preset seleccionado en ese momento. El LED SIG se ilumina al detectar una seal en la entrada del procesador. Si se ilumina el LED de saturacin, CLIP, reduzca la seal de entrada del procesador mediante el control FX correspondiente (2).

(8) Al girar este control se seleccionan los presets de efectos (el nombre del preset parpadea). Para confirmar su seleccin pulse brevemente el control.

(9) El control LEVEL de la seccin principal determina el volumen general de salida del amplificador.

(10) El control FX RET le permite aadir la seal de efectos a la seal principal.

(11) El pulsador SHAPE activa esta funcin en la seal principal. La funcin Shape de su ULTRATONE le provee un revolu-cionario filtro para alterar el sonido de su teclado (nicamente K3000FX y K1800FX).

(12) Utilice la salida PHONES para conectar sus auriculares.

(13) El control PHONES LEVEL regula el nivel de salida de los auriculares (nicamente K3000FX y K1800FX).

(14) Con el interruptor POWER se enciende el ULTRATONE. ste debe estar en la posicin de apagado al conectar el amplificador a la red de corriente elctrica.

(15) Utilice el cable suministrado para conectar su equipo a la red de corriente elctrica.

(16) PORTAFUSIBLES / SELECCIN DE TENSIN. Antes de conectar su ULTRATONE a la red de corriente elctrica, asegrese de que el indicador de tensin de ste corresponda a la tensin de red local. Si sustituye el fusible debe emplear indispensablemente uno del mismo tipo. En algunos aparatos el portafusibles puede colocarse en dos posiciones distintas para conmutar entre 230 V y 120 V. Si desea usar el aparato fuera de Europa, a 120 V por ejemplo, debe utilizar un fusible con valor distinto.

(17) Al activar el interruptor de separacin de masa GROUND LIFT (pulsador presionado) se interrumpe la conexin a tierra de la salida LINE OUT, eliminando as ruidos provoca-dos por bucles de masa (nicamente K3000FX y K1800FX).

(18) Utilice los conectores XLR balanceados designados como LINE OUT para alimentar la seal de su ULTRATONE a un mezclador (nicamente K3000FX y K1800FX). La seal de la salida LINE OUT es postecualizador, es decir, siempre se ver afectada por los ajustes realizados en el ecualizador.

(19) Las salidas LINE OUT son mediante jacks mono de 6,3 mm (K900FX y K450FX: un jack mono de 6,3 mm). Ambos conectores XLR y jack mono de 6,3 mm para la salida LINE OUT pueden usarse simultneamente.

(20) Para operacin en estreo, el ULTRATONE dispone la opcin STEREO LINK. sta le permite conectar la salida OUT del ULTRATONE a la entrada LINK IN de otro amplificador de teclado, que funcionar como esclavo, para obtener una autntica reproduccin estreo. Al utilizar el ULTRATONE como esclavo debe conectar la salida LINK OUT del ampli-ficador maestro a la entrada IN de su ULTRATONE (nicamente K3000FX y K1800FX).

(21) La salida SUB OUT le permite alimentar la seal de subwoofer con nivel de lnea de su ULTRATONE a una etapa de potencia o subwoofer activo.

(22) Para activar o desactivar los efectos mediante un pedal, conecte ste en la entrada FOOT SW.

(23) Utilice la entrada CD IN para conectar la salida de un reproductor de CD, casetera o MP3 a su amplificador. Esto le permite tocar simultneamente con su msica favorita o algn curso de teclado en CD.

(24) Entradas de lnea de los canales 1-4 (K3000FX/K1800FX) / canals 1-3 (K900FX/ K450FX) mediante. Para seales de entrada mono, utilice el conector L (MONO).

(25) El canal 1 est equipado con una entrada XLR para MIC(rfono). La alimentacin fantasma de +15 V le permite incluso utilizar micrfonos de condensador. Ambos conec- tores XLR y jack mono de 6,3 mm pueden se usados simult-neamente. En este caso, el control LEVEL del canal 1 regula el nivel de la seal de lnea y de la seal de micrfono.

18 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 19

(FR) Etape 2 : Rglages (DE) Schritt 2: Bedienelemente

(1) Les potentiomtres LEVEL dterminent le niveau du signal des canaux 1 4 (K900FX et K450FX : canaux 1  3).

(2) Les quatre commandes FX rglent le niveau du signal des canaux 1 4 lentre du multi-effet intgr (K900FX et K4500FX : trois commandes pour les canaux 1 3).

(3) Le signal du canal 4 (K3000FX et K1800FX uniquement) est normalement rout sans effet sur la sortie casque PHONES. Ainsi, vous pouvez jouer sans tre entendu. Vous pouvez galement alimenter le canal 4 avec un mtronome que vous souhaitez entendre dans le casque mais pas dans les haut-parleurs. Appuyez sur la touche TO MAIN pour assigner le signal sans effet du canal 4 galement aux haut-parleurs de lampli.

(4) Appuyez sur la touche TO LINE OUT pour router le signal sans effet du canal 4 galement sur la sortie LINE OUT (K3000FX et K1800FX uniquement). Appuyez sur les deux touches TO MAIN et TO LINE pour que le canal 4 se comporte comme les canaux 1 3. Le signal avec effet est alors assign aux haut- parleurs et la sortie ligne LINE OUT.

(5) LULTRATONE est dot dun galiseur graphique 7 bandes (K900FX et K450FX : galiseur graphique 5 bandes). Utilisez lgaliseur pour adapter le son lacoustique des lieux.

(6) Appuyez sur la touche FBQ pour activer le systme FBQ de dtection de larsens. Les frquences daccrochage sont indiques par lintensit lumineuse suprieure de la LED des faders. Dans ce cas, rduisez simplement le niveau de la bande de frquences en question jusqu ce que la LED se brille normalement et le larsen disparaisse.

(7) Lafficheur FX indique la preset deffet momentanment active. La LED SIG sallume lorsque le processeur deffets est aliment par un signal. Si la LED CLIP sallume, rduisez le niveau des signaux alimentant le multi-effet en utilisant leur potentiomtre FX (2).

(8) Tournez le rotatif FX pour slectionner une preset deffet (le numro de preset commence clignoter). Appuyez brivement sur lencodeur pour valider la slection.

(9) Utilisez le potentiomtre LEVEL de la section principale Master/Main pour rgler le volume de sortie global.

(10) Tournez le bouton FX RET pour ajouter le signal deffet la section principale Main.

(11) Appuyez sur la touche SHAPE pour traiter le signal principal Main avec cette fonction de votre ULTRATONE. Shape est un type de filtre rvolutionnaire trs utile pour le traitement de vos sons de clavier (K3000FX et K1800FX uniquement).

(12) Reliez votre casque audio la sortie PHONES.

(13) Le bouton PHONES LEVEL dtermine le volume du signal de la sortie casque (K3000FX et K1800FX uniquement).

(14) Utilisez le commutateur POWER pour allumer ou teindre votre ULTRATONE. Assurez-vous systmatiquement que POWER est en position Arrt avant de relier lampli la tension secteur.

(15) CONNEXION SECTEUR. Utilisez le cordon dalimentation fourni pour relier lampli la tension secteur.

(16) PORTE-FUSIBLE/SELECTEUR DE TENSION. Avant de brancher lampli, assurez-vous quil est rgl sur la tension adquate. Tout fusible dfectueux doit tre remplac par un fusible de mme type. Sur certains appareils, le p orte-fusible peut permettre de commuter entre 230 V et 120 V. Installez un fusible de valeur suprieure si vous alimentez lampli en 120 V hors dEurope.

(17) La touche GROUND LIFT dsactive (touche enfonce) la mise la terre de la sortie LINE OUT afin de supprimer deventuels ronflements induits par le courant alternatif (K3000FX et K1800FX uniquement).

(18) Utilisez la sortie LINE OUT sur XLR symtriques pour alimenter une table de mixage avec le signal de lULTRATONE (K3000FX et K1800FX uniquement). Le signal LINE OUT est prlev aprs lgaliseur.

(19) Il sagit des sorties LINE OUT sur jacks asymtriques (K900FX et K450FX : un seul jack asymtrique). Vous pouvez utiliser simultanment les connec-teurs XLR et jack de la sortie LINE OUT.

(20) LULTRATONE possde une option STEREO LINK destine aux applications stro. Vous pouvez relier la sortie OUT de lULTRATONE lentre LINK IN dun autre ampli clavier afin dobtenir une diffusion en vritable stro. Si vous utilisez lULTRATONE comme esclave, cblez la sortie LINK OUT de lampli matre avec lentre IN de lULTRATONE (K3000FX et K1800FX uniquement).

(21) La sortie SUB OUT dlivre un signal ligne mono pour subwoofer. Reliez-la lentre dun ampli de puissance ou lentre dun subwoofer actif.

(22) Raccordez votre pdale au jack FOOT SW afin de pouvoir activer/dsactiver distance le multi-effet de lampli.

(23) Utilisez lentre CD IN pour cbler la sortie de votre lecteur CD, cassette ou MP3  lULTRATONE afin de pouvoir jouer sur vos morceaux prfrs ou avec des CD pdagogiques.

(24) LINE sont les entres ligne sur jacks asymtriques des canaux 1-4 (K3000FX/ K1800FX) / canaux 1-3 (K900FX/K450FX). Utilisez uniquement lentre gauche L (MONO) pour alimenter un canal avec une source mono.

(25) Le canal 1 est dot dune entre micro MIC supplmentaire sur XLR. Grce  lalimentation fantme interne + 15 V de lULTRATONE, vous pouvez mme relier un micro lectrostatique lentre micro. Vous pouvez utiliser simultanment les entres sur XLR et jack asymtrique du canal. Dans ce cas, le potentiomtre LEVEL du canal 1 rgle le niveau des deux sources (ligne et micro).

(1) Mit den LEVEL-Reglern bestimmen Sie die Lautstrke fr die Kanle 1 - 4 (K900FX und K450FX: Kanle 1 - 3).

(2) Die vier FX-Regler von Kanal 1 - 4 bestimmen den Signalpegel, der vom jeweiligen Kanal zum integrierten Effektprozessor geleitet wird (K900FX und K450FX: drei Regler fr die Kanle 1 - 3).

(3) Das Signal von Kanal 4 (nur K3000FX und K1800FX) ist nur auf den PHONES-Ausgang geschaltet (ohne Effekt). Auf diese Weise knnen Sie lautlos ben, oder ein Metronom anschlieen, das Sie auf dem Kopfhrer brauchen, aber nicht auf den Lautsprechern. Durch Drcken des TO MAIN-Schalters wird das Signal zustzlich, ebenfalls ohne Effekt, ber die Lautsprecher hrbar.

(4) Durch Drcken des TO LINE OUT-Schalters kann das Kopfhrersignal von Kanal 4 zustzlich, ohne Effekte an den LINE OUT- Ausgngen abgegriffen werden. Sind sowohl TO MAIN als auch TO LINE OUT gedrckt, ist Kanal 4 gleichwertig mit den Kanlen 1 - 3. Das Signal wird inklusive Effekt ber die Lautsprecher hrbar und kann an den LINE- Ausgngen abgegriffen werden.

(5) Der ULTRATONE K3000FX/K1800FX besitzt einen grafischen 7-Band Equalizer (K900FX/ K450FX: 5-Band Equalizer). Mit seiner Hilfe passen Sie den Klang den rumlichen Gegebenheiten an.

(6) Wenn Sie den FBQ-Schalter drcken, wird das FBQ Feedback-Erkennungssystem aktiviert. Frequenzen, die Rckkopplungen hervorrufen, werden in Form von hell leuchtenden Fader-LEDs angezeigt. Alle anderen LEDs werden gedmpft. Senken Sie nun einfach den betreffen den Frequenzbereich etwas ab, bis das Feedback nicht mehr auftritt und die LED dunkler wird bzw. erlischt.

(7) Das Effekt-Display zeigt stets an, welches Preset aktiv ist. Die SIG-LED leuchtet auf, sobald der Effektprozessor ein Eingangssignal erhlt. Wenn die CLIP-LED aufleuchtet, reduzieren Sie bitte das Effekteingangssignal mit Hilfe der entsprechenden FX-Regler (2).

(8) Durch Drehen des FX-Reglers whlen Sie ein Effektprogramm aus (die Preset-Nummer blinkt). Zur Aktivierung des gewhlten Effekts drcken Sie kurz auf den Regler.

(9) Der LEVEL-Regler der Master-Sektion bestimmt die ber die Lautsprecher wiedergegebene Gesamtlautstrke.

(10) Mit FX RET wird der Anteil des gewhlten Effektes im Main Mix geregelt.

(11) Durch Drcken des SHAPE-Tasters fgen Sie dem Gesamtsignal den Shape-Effekt hinzu. Die Shape-Funktion des ULTRATONE bietet einen revolutionren Filtertyp, der dem Keyboard-Sound den letzten Schliff verleiht (nur K3000FX und K1800FX).

(12) Der PHONES-Ausgang dient zum Anschluss eines Kopfhrers.

(13) Der PHONES LEVEL-Regler bestimmt die Lautstrke des Kopfhrersignals (nur K3000FX und K1800FX).

(14) Mit dem POWER-Schalter wird der ULTRATONE in Betrieb genommen. Der POWER-Schalter sollte sich in der Stellung Aus befinden, wenn Sie die Verbindung zum Stromnetz herstellen.

(15) Die Netzverbindung erfolgt ber eine IEC-KALTGERTEBUCHSE. Ein passendes Netzkabel gehrt zum Liefer umfang.

(16) SICHERUNGSHALTER/SPANNUNGSWAHL. Bevor Sie das Gert mit dem Netz verbinden, berprfen Sie bitte, ob die Spannungsanzeige mit Ihrer lokalen Netzspannung bereinstimmt. Beim Ersetzen der Sicherung sollten Sie unbedingt den gleichen Typ verwenden. Bei manchen Gerten kann der Sicherungshalter in zwei Positionen eingesetzt werden, um zwischen 230 V und 120 V umzuschalten. Beachten Sie bitte: Wenn Sie ein Gert auerhalb Europas auf 120 V betreiben wollen, muss ein grerer Sicherungswert eingesetzt werden.

(17) Mit dem GND LIFT-Schalter (Ground Lift) knnen Sie die Masseverbindung des LINE OUT-Anschlusses trennen (Schalter gedrckt), um Brummgerusche oder Masseschleifen zu verhindern (nur K3000FX und K1800FX).

(18) An den symmetrischen XLR LINE OUT- Ausgngen kann das Keyboard-Signal abgegriffen und an ein Mischpult weitergeleitet werden (nur K3000FX und K1800FX). Die LINE OUT-Signale werden post-EQ ausgespielt.

(19) Dies sind die LINE OUT-Ausgnge auf 6,3-mm-Monoklinken steckern. Die XLR- und Klinkenanschlsse knnen gleichzeitig verwendet werden.

(20) Die STEREO LINK-Anschlsse des ULTRATONE bieten die Mglichkeit zum Stereobetrieb. Den OUT-Anschluss knnen Sie mit dem LINK IN-Anschluss eines zweiten Keyboard- Verstrkers verbinden, der dann als Slave dient, um True Stereo-Sound zu erreichen. Um den ULTRATONE als Slave zu verwenden, schlieen Sie den LINK OUT- Anschluss des zweiten Verstrkers an den IN-Anschluss an (nur K3000FX und K1800FX).

(21) An der SUB OUT-Buchse kann ein Mono- Subwoofer-Signal mit Line-Pegel abgegriffen werden, um dieses an einen zustzlichen Verstrker oder einen aktiven Monitor weiterzuleiten.

(22) An der FOOT SW-Buchse knnen Sie einen Fuschalter anschlieen, um den internen Effektprozessor des ULTRATONE ein- und auszuschalten.

(23) An den CD IN knnen CD-Player, Tape Deck, oder MP3 Player angeschlossen werden. Auf diese Weise knnen Sie Musik laufen lassen und dazu spielen.

(24) Hier befinden sich die LINE-Eingangsbuchsen der Kanle 1-4 (K3000FX/K1800FX) / Kanle 1-3 (K900FX/K450FX). Wenn Sie ein Monosignal anschlieen wollen, verwenden Sie bitte den linken Kanal L (MONO).

(25) Kanal 1 ist mit einem zustzlichen XLR MIC-Eingang ausgestattet. Er bietet eine interne +15 V-Phantom speisung, die die Verwendung von Kondensatormikrofonen ermglicht. Der XLR-Anschluss und die 6,3-mm-Klinken buchsen knnen gleichzeitig genutzt werden. In diesem Fall regelt der LEVEL-Regler von Kanal 1 gleichzeitig das LINE- und das MIC-Signal.

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Controls

20 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 21

(PT) Passo 2: Controles

(1) Os controlos de LEVEL regulam o nvel do sinal dos canais 1 - 4 (K900FX e K450FX: canais 1 - 3).

(2) Os quatro controlos FX regulam o nvel do sinal do canal 1 - 4 na entrada do processador de efeitos integrados (K900FX e K4500FX: trs controlos para os canais 1 - 3).

(3) O sinal do canal 4 (apenas no K3000FX e K1800FX)  normalmente direccionado apenas para a sada dos AUSCULTADORES sem efeitos. Assim, poder praticar sem ser ouvido ou poder ligar um metrnomo de que necessita nos auscultadores e no nas colunas. Ao premir o boto TO MAIN, o sinal ser adicionalmente direccionado para as colunas sem efeitos.

(4) Ao premir o boto TO LINE OUT, o sinal do canal 4 ser adicionalmente direccionado para a sada da LINE OUT sem efeitos (apenas no K3000FX e K1800FX). Se premir ambos os botes TO MAIN e TO LINE, o canal 4 ficar igual aos canais 1 - 3. O sinal ser direccionado para as colunas e a sada da LINE OUT, incluindo efeitos.

(5) O ULTRATONE est equipado com um equalizador grfico de 7 bandas (K900FX e K450FX: equalizador grfico de 5 bandas). Utilize o Equalizador para adaptar o som acstica da sala.

(6) Prima o interruptor FBQ para activar o Sistema de Deteco de Retorno FBQ. As frequncias que causam o retorno de som so apresentadas atravs dos Indicadores Luminosos acesos do potencimetro. Baixe simplesmente o nvel do respectivo intervalo de frequncia at o retorno de som desaparecer e os Indicadores Luminosos se apagarem.

(7) O ecr FX apresenta a predefinio actualmente definida. O Indicador Luminoso SIG acende-se quando o processador de efeitos recebe a entrada de um sinal. Quando o Indicador Luminoso CLIP acender, por favor reduza a entrada de sinais de efeitos. utilizando o(s) respectivo(s) controlo(s) FX (2).

(8) Rode o controlo FX para seleccionar uma predefinio de efeitos (o nmero predefinido ficar intermitente). Prima brevemente o controlo para confirmar a sua seleco.

(9) O controlo LEVEL na seco bsica utilizado para regular o volume da sada principal.

(10) Rode o controlo FX RET para adicionar o sinal de efeito mistura principal.

(11) Ao premir o boto SHAPE adicionar o efeito de Forma ao sinal principal. A funo Shape no seu ULTRATONE fornece um tipo revolucionrio de filtro que pode utilizar para modificar o som do seu teclado (apenas no K3000FX e K1800FX).

(12) Utilize o conector dos PHONES para ligar os seus auscultadores.

(13) O controlo PHONES LEVEL regula o nvel de sada dos auscultadores (apenas no K3000FX e K1800FX).

(14) Utilize o interruptor POWER para ligar e desligar o ULTRATONE. Certifique-se sempre de que o interruptor POWER est na posio de Off quando inicialmente ligar a unidade corrente elctrica.

(15) LIGAO CORRENTE ELCTRICA. Utilize o cabo elctrico fornecido com esta unidade para lig-la corrente elctrica.

(16) PORTA-FUSVEIS/SELECTOR DE VOLTAGEM. Antes de ligar a unidade corrente elctrica, certifique-se de que as definies de voltagem correspondem sua voltagem local. Um fusvel fundido dever apenas ser substitudo por outro fusvel do mesmo tipo e potncia. Nalgumas unidades, o porta-fusveis pode ser colocado numa de duas posies, por exemplo 230 V e 120 V. Quando trabalhar com a unidade fora da Europa com 120 V, ser necessrio um fusvel de potncia superior.

(17) O interruptor GROUND LIFT desliga a ligao terra (interruptor premido) na sada LINE OUT para eliminar eficazmente rudos de zumbido resultantes de elos de terra (apenas no K3000FX e K1800FX).

(18) Utilize os conectores balanceados LINE OUT XLR para alimentar o sinal de udio do seu ULTRATONE a uma consola de mistura (apenas no K3000FX e K1800FX). O sinal da LINE OUT ps-equalizador.

(19) Estas so as sadas LINE OUT nos conectores mono de 6,3 mm (K900FX e K450FX: um conector mono de 6,3 mm). Ambos os conectores TS e XLR de 6,3 mm de LINE OUT podem ser utilizados simultaneamente.

(20) Para funcionamento estereofnico, o ULTRATONE inclui uma funo de STEREO LINK. Pode ligar a OUT do ULTRATONE LINK IN de outro amplificador de teclado que esteja a funcionar como dependente para conseguir um verdadeiro som estereofnico. Quando utilizar o ULTRATONE como dependente, ligue a LINK OUT do amplificador principal IN (apenas no K3000FX e K1800FX).

(21) O conector SUB OUT fornece o sinal de Subwoofer mono nvel de linha para ligao entrada de um amplificador de potencia ou de um Subwoofer activo.

(22) Ligue o seu interruptor de pedal ao conector FOOT SW, para poder activar/desactivar o processador de efeitos.

(23) Utilize os conectores de CD IN para ligar a sada dos seu leitor de CD, cassetes ou de MP3 porttil. Desta forma, pode acompanhar uma msica ou os CDs de instrues do teclado.

(24) Estas so as entradas de LINE para os canais 1-4 (K3000FX/K1800FX) / canais 1-3 (K900FX/ K450FX) nos conectores. Para entradas de sinais mono, por favor utilize o conector L (MONO).

(25) O canal 1 est equipado com uma entrada adicional XLR MIC. Em virtude da energia fantasma interna de +15 V, poder mesmo utilizar microfones condensadores. Ambos os conectores XLR e mono de 6,3 mm podem ser utilizados simultaneamente. Neste caso, o controlo do LEVEL do canal 1 ajusta os nveis de ambos para o sinal de LINE e de MICROFONE.

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Controls

(IT) Step 2: Controls

(1) I controlli LEVEL regolano il livello del segnale dei canali 1 - 4 (K900FX e K450FX: canali 1 - 3).

(2) I quattro controlli FX regolano il livello del segnale del canale 1 - 4 all'ingresso del processore di effetti integrato (K900FX e K450FX: tre controlli per i canali 1 - 3).

(3) Il segnale del canale 4 (solo K3000FX e K1800FX) viene normalmente indirizzato solo all'uscita PHONES senza effetti. In questo modo puoi esercitarti senza essere ascoltato, oppure puoi collegare un metronomo di cui hai bisogno sulle cuffie ma non sugli altoparlanti. Premendo il pulsante TO MAIN il segnale verr inoltre inviato agli altoparlanti senza effetti.

(4) Premendo il pulsante TO LINE OUT il segnale del canale 4 verr inoltre indirizzato all'uscita LINE OUT senza effetti (solo K3000FX e K1800FX). Se si premono entrambi i pulsanti TO MAIN e TO LINE, il canale 4 sar uguale ai canali 1 - 3. Il segnale verr indirizzato agli altoparlanti e all'uscita LINE OUT inclusi gli effetti.

(5) L'ULTRATONE dotato di un equalizzatore grafico a 7 bande (K900FX e K450FX: equalizzatore grafico a 5 bande). Usa l'EQ per adattare il suono all'acustica della stanza.

(6) Premere l'interruttore FBQ per attivare il sistema di rilevamento feedback FBQ. Le frequenze che causano il feedback sono mostrate dai LED dei fader luminosi. Abbassate semplicemente il livello della rispettiva gamma di frequenza fino a quando il feedback scompare e il LED si spegne.

(7) Il display FX mostra il preset attualmente selezionato. Il LED SIG si accende quando il processore di effetti riceve un segnale in ingresso. Quando il LED CLIP si accende, ridurre il segnale di ingresso degli effetti utilizzando i rispettivi controlli FX (2).

(8) Ruotare il controllo FX per selezionare un preset di effetti (il numero del preset inizia a lampeggiare). Premere brevemente il controllo per confermare la selezione.

(9) Il controllo LEVEL nella sezione master viene utilizzato per regolare il volume di uscita principale.

(10) Ruota il controllo FX RET per aggiungere il segnale dell'effetto al mix principale.

(11) Premendo il pulsante SHAPE si aggiunger l'effetto Shape al segnale principale. La funzione Shape sul tuo ULTRATONE fornisce un rivoluzionario tipo di filtro che puoi usare per modificare il suono della tua tastiera (solo K3000FX e K1800FX).

(12) Utilizzare la presa PHONES per collegare le cuffie.

(13) Il controllo PHONES LEVEL regola il livello di uscita delle cuffie (solo K3000FX e K1800FX).

(14) Utilizzare l'interruttore POWER per accendere o spegnere ULTRATONE. Assicurarsi sempre che l'interruttore POWER sia in posizione "Off" quando si collega inizialmente l'unit alla rete elettrica.

(15) COLLEGAMENTO ALLA RETE. Utilizzare il cavo di alimentazione fornito con l'unit per collegarla alla rete elettrica.

(16) PORTAFUSIBILE / SELETTORE DI TENSIONE. Prima di collegare l'unit alla rete, assicurarsi che l'impostazione della tensione corrisponda alla tensione locale. Un fusibile bruciato deve essere sostituito solo da un fusibile dello stesso tipo e valore. Su alcune unit, il portafusibile pu essere commutato in una delle due posizioni, ovvero 230 V e 120 V. Quando si utilizza l'unit fuori dall'Europa a 120 V, richiesta una classificazione del fusibile pi alta.

(17) L'interruttore GROUND LIFT scollega (interruttore premuto) il collegamento di terra all'uscita LINE OUT per eliminare efficacemente il ronzio derivante dai loop di massa (solo K3000FX e K1800FX).

(18) Usa i connettori LINE OUT XLR bilanciati per inviare il segnale audio dal tuo ULTRATONE a una console di missaggio (solo K3000FX e K1800FX). Il segnale LINE OUT post-EQ.

(19) Queste sono le uscite LINE OUT sui connettori TS da 1/4 "(K900FX e K450FX: un connettore TS da 1/4"). Entrambi i connettori XLR e TS LINE OUT da 1/4 "possono essere utilizzati contemporaneamente.

(20) Per il funzionamento stereo, ULTRATONE dispone di una funzione STEREO LINK. possibile collegare OUT dell'ULTRATONE al LINK IN di un altro amplificatore per tastiera che funge da slave per ottenere un vero suono stereo. Quando si utilizza ULTRATONE come

slave, collegare il LINK OUT dell'amplificatore master a IN (solo K3000FX e K1800FX).

(21) Il connettore SUB OUT fornisce il segnale del subwoofer mono a livello di linea per il collegamento all'ingresso di un amplificatore di potenza o di un subwoofer attivo.

(22) Collega il tuo interruttore a pedale alla presa FOOT SW, in modo da attivare / disattivare il processore di effetti.

(23) Utilizzare i connettori CD IN per collegare l'uscita del lettore CD, della piastra di registrazione o del lettore MP3. In questo modo puoi suonare insieme alla musica o ai CD tutorial della tastiera.

(24) Questi sono gli ingressi LINE per i canali 1-4 (K3000FX / K1800FX) / canali 1-3 (K900FX / K450FX) sui connettori TS da ". Per i segnali di ingresso mono, utilizzare il connettore L (MONO).

(25) Il canale 1 dotato di un ingresso XLR MIC aggiuntivo. Grazie all'alimentazione phantom interna di +15 V possibile persino utilizzare microfoni a condensatore. Entrambi i connettori XLR e TS da 1/4 "possono essere utilizzati contemporaneamente. In questo caso il controllo LEVEL del canale 1 regola sia il livello del segnale LINE che MIC.

22 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 23

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Controls

(NL) Stap 2: Bediening (SE) Steg 2: Kontroller

(1) De LEVEL-regelaars regelen het signaalniveau van de kanalen 1 - 4 (K900FX en K450FX: kanalen 1 - 3).

(2) De vier FX-regelaars regelen het signaalniveau van kanaal 1 - 4 aan de ingang van de gentegreerde effectprocessor (K900FX en K450FX: drie regelaars voor kanalen 1 - 3).

(3) Het kanaal 4-signaal (alleen K3000FX en K1800FX) wordt normaal gesproken zonder effecten naar de PHONES-uitgang gerouteerd. Op deze manier kun je oefenen zonder gehoord te worden, of je kunt een metronoom die je nodig hebt aansluiten op een koptelefoon maar niet op speakers. Door op de TO MAIN-knop te drukken, wordt het signaal bovendien zonder effecten naar de luidsprekers geleid.

(4) Door op de TO LINE OUT-knop te drukken, wordt het signaal van kanaal 4 bovendien zonder effecten naar de LINE OUT-uitgang geleid (alleen K3000FX en K1800FX). Als u zowel de TO MAIN- als de TO LINE-knop indrukt, is kanaal 4 gelijk aan kanaal 1 - 3. Het signaal wordt naar de luidsprekers en de LINE OUT-uitgang inclusief effecten gestuurd.

(5) De ULTRATONE is uitgerust met een 7-bands grafische equalizer (K900FX en K450FX: 5-bands grafische equalizer). Gebruik de EQ om het geluid aan de akoestiek van de ruimte aan te passen.

(6) Druk op de FBQ-schakelaar om het FBQ Feedback Detection System te activeren. De frequenties die feedback veroorzaken, worden weergegeven door de helder verlichte fader-LED's. Verlaag gewoon het niveau van het respectieve frequentiebereik totdat de feedback verdwijnt en de LED uitgaat.

(7) Het FX-display toont de momenteel geselecteerde preset. De SIG-LED licht op als de effectprocessor een ingangssignaal ontvangt. Als de CLIP-LED oplicht, verminder dan het ingangssignaal van de effecten met behulp van de respectievelijke FX-regelaar (s) (2).

(8) Draai aan de FX-regelaar om een effectvoorinstelling te selecteren (het voorkeuzenummer begint te knipperen). Druk kort op de knop om uw keuze te bevestigen.

(9) De LEVEL-regelaar in de master-sectie wordt gebruikt om het hoofduitgangsvolume aan te passen.

(10) Draai aan de FX RET-regelaar om het

effectsignaal aan de hoofdmix toe te voegen.

(11) Door op de SHAPE-knop te drukken, wordt het Shape-effect aan het hoofdsignaal toegevoegd. De Shape-functie op uw ULTRATONE biedt een revolutionair filtertype dat u kunt gebruiken om uw toetsenbordgeluid te wijzigen (alleen K3000FX en K1800FX).

(12) Gebruik de PHONES-aansluiting om uw hoofdtelefoon aan te sluiten.

(13) De PHONES LEVEL-regelaar past het uitgangsniveau van de hoofdtelefoon aan (alleen K3000FX en K1800FX).

(14) Gebruik de POWER-schakelaar om de ULTRATONE in of uit te schakelen. U moet er altijd voor zorgen dat de POWER-schakelaar in de Off -stand staat wanneer u het apparaat voor het eerst op het lichtnet aansluit.

(15) NETAANSLUITING. Gebruik het bij het apparaat geleverde netsnoer om het op het lichtnet aan te sluiten.

(16) ZEKERINGHOUDER / VOLTAGE SELECTOR. Voordat u het apparaat op het lichtnet aansluit, moet u ervoor zorgen dat de spanningsinstelling overeenkomt met uw plaatselijke netspanning. Een doorgebrande zekering mag alleen worden vervangen door een zekering van hetzelfde type en dezelfde waarde. Bij sommige units kan de zekeringhouder in een van de twee standen worden geschakeld, namelijk 230 V en 120 V. Bij gebruik van de unit buiten Europa op 120 V is een hogere zekering vereist.

(17) De GROUND LIFT-schakelaar verbreekt (schakelaar ingedrukt) de massa-aansluiting op de LINE OUT-uitgang om bromgeluid als gevolg van aardlussen effectief te elimineren (alleen K3000FX en K1800FX).

(18) Gebruik de gebalanceerde LINE OUT XLR- connectoren om het audiosignaal van uw ULTRATONE naar een mengtafel te leiden (alleen K3000FX en K1800FX). Het LINE OUT- signaal is post-EQ.

(19) Dit zijn de LINE OUT-uitgangen op 1/4 "TS-connectoren (K900FX en K450FX: een 1/4" TS-connector). Zowel XLR- als 1/4 "TS LINE OUT-connectoren kunnen tegelijkertijd worden gebruikt.

(20) Voor stereowerking is de ULTRATONE voorzien van een STEREO LINK-functie. U kunt de OUT van de ULTRATONE aansluiten op de LINK IN van een andere keyboardversterker die als

slaaf dient om echt stereogeluid te verkrijgen. Als u de ULTRATONE als slave gebruikt, sluit u de LINK OUT van de masterversterker aan op de IN (alleen K3000FX en K1800FX).

(21) De SUB OUT-connector levert het mono-subwoofersignaal op lijnniveau voor aansluiting op de ingang van een eindversterker of actieve subwoofer.

(22) Sluit uw voetschakelaar aan op de FOOT SW-aansluiting om de effectprocessor te activeren / deactiveren.

(23) Gebruik de CD IN-aansluitingen om de uitgang van uw cd-speler, tapedeck of mp3- speler aan te sluiten. Op deze manier kunt u meespelen met muziek of keyboard tutorial CD's.

(24) Dit zijn de LINE-ingangen voor kanalen 1-4 (K3000FX / K1800FX) / kanalen 1-3 (K900FX / K450FX) op "TS-aansluitingen. Gebruik voor mono-ingangssignalen de L (MONO) -aansluiting.

(25) Kanaal 1 is uitgerust met een extra XLR MIC- ingang. Door interne +15 V fantoomvoeding kunt u zelfs condensatormicrofoons gebruiken. Zowel XLR- als 1/4 "TS-connectoren kunnen tegelijkertijd worden gebruikt. In dit geval past de LEVEL-regelaar van kanaal 1 zowel het niveau van het LINE- als het MIC-signaal aan.

(1) LEVEL-kontrollerna justerar signalnivn fr kanalerna 1 - 4 (K900FX och K450FX: kanalerna 1-3).

(2) De fyra FX-kontrollerna justerar kanal 1-4 signalnivn vid ingngen till den integrerade effektprocessorn (K900FX och K450FX: tre kontroller fr kanalerna 1-3).

(3) Kanal 4-signalen (endast K3000FX och K1800FX) dirigeras normalt bara till PHONES- utgngen utan effekter. P s stt kan du va utan att bli hrd, eller s kan du ansluta en metronom som du behver p hrlurar men inte p hgtalare. Genom att trycka p TO MAIN-knappen dirigeras signalen till hgtalarna utan effekter.

(4) Genom att trycka p TO LINE OUT-knappen dirigeras kanal 4-signalen till LINE OUT- utgngen utan effekter (endast K3000FX och K1800FX). Om du trycker p bde TO MAIN- och TO LINE-knappen kommer kanal 4 att vara lika med kanalerna 1 - 3. Signalen dirigeras till hgtalarna och LINE OUT-utgngen inklusive effekter.

(5) ULTRATONE r utrustad med en 7-band grafisk equalizer (K900FX och K450FX: 5-band grafisk equalizer). Anvnd EQ fr att anpassa ljudet till rumsakustiken.

(6) Tryck p FBQ-omkopplaren fr att aktivera FBQ Feedback Detection System. Frekvenserna som orsakar terkoppling visas av de starkt tnda lysdioderna fr fader. Snk helt enkelt nivn fr respektive frekvensomrde tills terkoppling frsvinner och lysdioden slocknar.

(7) FX-displayen visar den frinstllda frinstllningen. SIG-LED tnds nr effektprocessorn tar emot en insignal. Nr CLIP-lysdioden tnds, var vnlig minska effekten ingngssignal med hjlp av respektive FX-kontroll (er) (2).

(8) Vrid FX-reglaget fr att vlja en effektfrinstllning (frinstllningsnumret brjar blinka). Tryck kort p kontrollen fr att bekrfta ditt val.

(9) LEVEL-kontrollen i huvudsektionen anvnds fr att justera huvudutmatningsvolymen.

(10) Vrid FX RET-kontrollen fr att lgga till effektsignalen till huvudmixen.

(11) Genom att trycka p SHAPE-knappen lggs Shape-effekten till huvudsignalen. Shape-funktionen p din ULTRATONE ger en revolutionerande typ av filter som du kan

anvnda fr att ndra ditt tangentbordsljud (endast K3000FX och K1800FX).

(12) Anvnd PHONES-uttaget fr att ansluta hrlurarna.

(13) PHONES LEVEL-kontrollen justerar hrlurarnas utgngsniv (endast K3000FX och K1800FX).

(14) Anvnd POWER-omkopplaren fr att sl p eller av ULTRATONE. Du br alltid se till att POWER-omkopplaren r i Off -lget nr du frst ansluter enheten till elntet.

(15) HUVUDANSLUTNING. Anvnd den medfljande strmsladden fr att ansluta den till elntet.

(16) SKRINGSHLLARE / SPNNINGSVLJARE. Innan du ansluter enheten till elntet, se till att spnningsinstllningen matchar din lokala spnning. En utbruten skring br endast bytas ut mot en skring av samma typ och klass. P vissa enheter kan skringshllaren bytas till en av tv lgen, dvs. 230 V och 120 V. Nr du anvnder enheten utanfr Europa vid 120 V krvs en hgre skring.

(17) GROUND LIFT-omkopplaren kopplar bort (brytaren trycks ned) jordanslutningen vid LINE OUT-utgngen fr att effektivt eliminera brus frn jordglor (endast K3000FX och K1800FX).

(18) Anvnd de balanserade LINE OUT XLR- kontakterna fr att mata ljudsignalen frn din ULTRATONE till en blandningskonsol (endast K3000FX och K1800FX). LINE OUT-signalen r post-EQ.

(19) Det hr r LINE OUT-utgngarna p 1/4 "TS-kontakter (K900FX och K450FX: en 1/4" TS-kontakt). Bde XLR- och 1/4 "TS LINE OUT- kontakter kan anvndas samtidigt.

(20) Fr stereodrift har ULTRATONE en STEREO LINK-anlggning. Du kan ansluta ULTRATONE OUT till LINK IN p en annan tangentbordfrstrkare som fungerar som slav fr att uppn kta stereoljud. Nr du anvnder ULTRATONE som slav, anslut LINK OUT p huvudfrstrkaren till IN (endast K3000FX och K1800FX).

(21) SUB OUT-kontakten ger mono-subwoofer- signalen p linjeniv fr anslutning till ingngen till en effektfrstrkare eller aktiv subwoofer.

(22) Anslut fotpedalen till FOOT SW-uttaget fr att aktivera / avaktivera effektprocessorn.

(23) Anvnd CD IN-kontakterna fr att ansluta utgngen frn din CD-spelare, kassettdck eller MP3-spelare. P det hr sttet kan du spela med p musik- eller tangentbord-CD- skivor.

(24) Detta r LINE-ingngarna fr kanalerna 1-4 (K3000FX / K1800FX) / kanalerna 1-3 (K900FX / K450FX) p "TS-kontakter. Fr monoingngssignaler anvnd L (MONO) -kontakten.

(25) Kanal 1 r utrustad med en extra XLR MIC-ingng. P grund av intern +15 V fantomeffekt kan du till och med anvnda kondensatormikrofoner. Bde XLR- och 1/4 "TS-kontakter kan anvndas samtidigt. I detta fall justerar LEVEL-kontrollen p kanal 1 bde nivn p LINE- och MIC-signalen.

24 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 25

K3000FX K1800FX K900FX K450FX Audio Inputs

Line In 1 - 4 " TS connector

Input impedance approx. 30 k balanced

Stereo Link In " TS connector

Input impedance approx. 20 k unbalanced

CD In RCA connector

Input impedance approx. 20 k unbalanced

Mic In 1 XLR connector

Input impedance approx. 2 k balanced

Audio Outputs

Headphones connector " TRS connector

Line Out " TS and XLR connector

Output impedance " TS connector: approx.150 unbalanced XLR connector: approx. 300 balanced

Stereo Link Out " TS connector

Output impedance approx. 150 unbalanced

Sub Out " TS connector

Output impedance approx. 150 unbalanced

Equalizer

Type Graphic EQ with FBQ Feedback Detection

Frequency range 63 Hz / 160 Hz / 400 Hz / 1 kHz / 2.5 kHz / 6.3 kHz / 12 kHz 63 Hz / 250 Hz / 1 kHz / 3.5 kHz / 12 kHz

Bandwidth 2/3-oct.

Control range +12 to -12 dB

Digital Effects Processor

Converters 24-bit sigma-delta, 64/128-times oversampling

Sampling rate 40 kHz

System Specifications

Power amp output 300 Watts 180 Watts 90 Watts 45 Watts

Loudspeaker

Type 15'' Bugera woofer and custom-made 1'' driver

12'' Bugera woofer and custom-made 1'' driver

12'' Bugera woofer and custom-made 1'' driver 10'' Bugera speaker

Input impedance 4

Power Supply

Mains Voltage

USA/Canada 120 V~, 60 Hz

U.K./Australia 230 V~, 50 Hz

Europe 230 V~, 50 Hz

China/Korea 220 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

General export model 120/230 V~, 50 - 60 Hz

Power consumption approx. 350 Watts approx. 290 Watts approx. 150 Watts approx. 75 Watts

Fuse 100 - 120 V~: 6.3 A H 250 V 220 - 240 V~: 3.15 A H 250 V

100 - 120 V~: 6.3 A H 250 V 220 - 240 V~: 3.15 A H 250 V

100 - 120 V~: 3.15 A H 250 V 220 - 240 V~: 1.6 A H 250 V

100 - 120 V~: 2.5 A H 250 V 220 - 240 V~: 1.25 A H 250 V

Mains connection Standard IEC receptacle

Dimensions/Weight

Dimensions approx. 20 7/8 x 23 1/2 x 16" approx. 530 x 597 x 406 mm

approx. 16 7/8 x 19 3/8 x 11 3/4" approx. 429 x 492 x 299 mm

approx. 16 7/8 x 19 3/8 x 11 3/4" approx. 429 x 492 x 299 mm

approx. 16 1/2 x 17 3/8 x 11 3/4" approx. 419 x 441 x 299 mm

Weight approx. 70.10 lbs / 31.8 kg approx. 42.32 lbs / 19.2 kg approx. 39.90 lbs / 18.1 kg approx. 34.83 lbs / 15.8 kg

SpecificationsULTRATONE K3000FX/K1800FX/K900FX/K450FX Controls

(PL) Krok 2: Sterowanica

(1) Elementy sterujce LEVEL su do regulacji poziomu sygnau kanaw 1 - 4 (K900FX i K450FX: kanay 1 - 3).

(2) Cztery regulatory FX reguluj poziom sygnau kanaw 1 - 4 na wejciu zintegrowanego procesora efektw (K900FX i K450FX: trzy regulatory dla kanaw 1 - 3).

(3) Sygna kanau 4 (tylko K3000FX i K1800FX) jest zwykle kierowany do wyjcia PHONES bez efektw. W ten sposb moesz wiczy bez syszenia lub moesz podczy metronom, ktrego potrzebujesz, do suchawek, ale nie do gonikw. Po naciniciu przycisku TO MAIN sygna bdzie dodatkowo kierowany do gonikw bez efektw.

(4) Po naciniciu przycisku TO LINE OUT sygna z kanau 4 zostanie dodatkowo skierowany do wyjcia LINE OUT bez efektw (tylko K3000FX i K1800FX). Jeli wciniesz jednoczenie przycisk TO MAIN i TO LINE, kana 4 bdzie rwny kanaom 1 - 3. Sygna zostanie skierowany do gonikw i na wyjcie LINE OUT wraz z efektami.

(5) ULTRATONE jest wyposaony w 7-pasmowy korektor graficzny (K900FX i K450FX: 5-pasmowy korektor graficzny). Uyj korektora, aby dostosowa dwik do akustyki pomieszczenia.

(6) Nacinij przecznik FBQ, aby aktywowa system wykrywania sprzenia zwrotnego FBQ. Czstotliwoci wywoujce sprzenie zwrotne s wskazywane przez jasno wiecce diody LED suwakw. Po prostu obni poziom odpowiedniego zakresu czstotliwoci, a zniknie sprzenie zwrotne i zganie dioda LED.

(7) Wywietlacz FX pokazuje aktualnie wybrany preset. Dioda SIG LED zapala si, gdy procesor efektw odbiera sygna wejciowy. Gdy zawieci si dioda CLIP, zmniejsz sygna wejciowy efektw za pomoc odpowiednich regulatorw FX (2).

(8) Obr regulator FX, aby wybra ustawienie wstpne efektw (numer presetu zacznie miga). Nacinij krtko pokrto, aby potwierdzi wybr.

(9) Pokrto LEVEL w sekcji gwnej suy do regulacji gonoci gwnego wyjcia.

(10) Obr regulator FX RET, aby doda sygna efektu do gwnego miksu.

(11) Nacinicie przycisku SHAPE doda efekt Shape do gwnego sygnau. Funkcja Shape

w ULTRATONE zapewnia rewolucyjny rodzaj filtra, ktrego moesz uy do modyfikacji brzmienia klawiatury (tylko K3000FX i K1800FX).

(12) Uyj gniazda PHONES, aby podczy suchawki.

(13) Pokrto PHONES LEVEL umoliwia regulacj poziomu wyjciowego suchawek (tylko modele K3000FX i K1800FX).

(14) Za pomoc przecznika POWER wcz lub wycz ULTRATONE. Naley zawsze upewni si, e przecznik POWER znajduje si w pozycji Off podczas pierwszego podczania urzdzenia do sieci.

(15) PODCZENIE DO SIECI. Uyj przewodu zasilajcego dostarczonego z urzdzeniem, aby podczy je do sieci elektrycznej.

(16) UCHWYT BEZPIECZNIKA / SELEKTOR NAPICIA. Przed podczeniem urzdzenia do sieci naley upewni si, e ustawienie napicia odpowiada lokalnemu napiciu. Przepalony bezpiecznik naley wymienia tylko na bezpiecznik tego samego typu i wartoci. W niektrych urzdzeniach uchwyt bezpiecznika mona przeczy na jedn z dwch pozycji, tj. 230 V i 120 V. Podczas eksploatacji urzdzenia poza Europ przy napiciu 120 V wymagana jest wysza warto znamionowa bezpiecznika.

(17) Przecznik GROUND LIFT rozcza (przecznik wcinity) uziemienie na wyjciu LINE OUT, aby skutecznie eliminowa szumy powstae w wyniku ptli uziemienia (tylko K3000FX i K1800FX).

(18) Uyj zbalansowanych zczy XLR LINE OUT do doprowadzenia sygnau audio z ULTRATONE do konsoli mikserskiej (tylko K3000FX i K1800FX). Sygna LINE OUT jest po korektorze.

(19) S to wyjcia LINE OUT na zczach TS 1/4 "(K900FX i K450FX: jedno zcze 1/4" TS). Oba zcza XLR i 1/4 "TS LINE OUT mog by uywane jednoczenie.

(20) Do pracy w trybie stereo ULTRATONE posiada funkcj STEREO LINK. Moesz podczy OUT ULTRATONE do LINK IN innego wzmacniacza klawiszowego, ktry suy jako slave, aby uzyska prawdziwy dwik stereo. Uywajc ULTRATONE jako slave, podcz LINK OUT wzmacniacza gwnego do IN (tylko K3000FX i K1800FX).

(21) Zcze SUB OUT dostarcza liniowy sygna mono subwoofera do podczenia do

wejcia wzmacniacza mocy lub aktywnego subwoofera.

(22) Podcz przecznik nony do gniazda FOOT SW, aby wczy / wyczy procesor efektw.

(23) Uyj zczy CD IN do podczenia wyjcia odtwarzacza CD, magnetofonu lub odtwarzacza MP3. W ten sposb moesz gra razem z pytami CD z muzyk lub samouczkami na klawiaturze.

(24) S to wejcia LINE dla kanaw 1-4 (K3000FX / K1800FX) / kanaw 1-3 (K900FX / K450FX) na zczach "TS. Dla sygnaw wejciowych mono uyj zcza L (MONO).

(25) Kana 1 wyposaony jest w dodatkowe wejcie XLR MIC. Dziki wewntrznemu zasilaniu phantom +15 V mona nawet uywa mikrofonw pojemnociowych. Oba zcza XLR i 1/4 "TS mog by uywane jednoczenie. W tym przypadku regulator LEVEL kanau 1 reguluje zarwno poziom sygnau LINE jak i MIC.

26 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 27

Other important information

1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.

2. Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under Support at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our Online Support which may also be found under Support at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.

3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

1. Registro online. Le recomendamos que registre su nuevo aparato Music Tribe justo despus de su compra accediendo a la pgina web musictribe.com. El registro de su compra a travs de nuestro sencillo sistema online nos ayudar a resolver cualquier incidencia que se presente a la mayor brevedad posible. Adems, aproveche para leer los trminos y condiciones de nuestra garanta, si es aplicable en su caso.

2. Averas. En el caso de que no exista un distribuidor Music Tribe en las inmediaciones, puede ponerse en contacto con el distribuidor Music Tribe de su pas, que encontrar dentro del apartado Support de nuestra pgina web musictribe.com. En caso de que su pas no aparezca en ese listado, acceda a la seccin Online Support (que tambin encontrar dentro del apartado Support de nuestra pgina web) y compruebe si su problema aparece descrito y solucionado all. De forma alternativa, envenos a travs de la pgina web una solicitud online de soporte en periodo de garanta ANTES de devolvernos el aparato.

3. Conexiones de corriente. Antes de enchufar este aparato a una salida de corriente, asegrese de que dicha salida sea del voltaje adecuado para su modelo concreto. En caso de que deba sustituir un fusible quemado, deber hacerlo por otro de idnticas especificaciones, sin excepcin.

1. Enregistrez-vous en ligne. Prenez le temps denregistrer votre produit Music Tribe aussi vite que possible sur le site Internet musictribe.com. Le fait denregistrer le produit en ligne nous permet de grer les rparations plus rapidement et plus efficacement. Prenez galement le temps de lire les termes et conditions de notre garantie.

2. Dysfonctionnement. Si vous navez pas de revendeur Music Tribe prs de chez vous, contactez le distributeur Music Tribe de votre pays : consultez la liste des distributeurs de votre pays dans la page Support de notre site Internet musictribe.com. Si votre pays nest pas dans la liste, essayez de rsoudre votre problme avec notre aide en ligne que vous trouverez galement dans la section Support du site musictribe.com. Vous pouvez galement nous faire parvenir directement votre demande de rparation sous garantie par Internet sur le site musictribe.com AVANT de nous renvoyer le produit.

3. Raccordement au secteur. Avant de relier cet quipement au secteur, assurez-vous que la tension secteur de votre rgion soit compatible avec lappareil. Veillez remplacer les fusibles uniquement par des modles exactement de mme taille et de mme valeur lectrique sans aucune exception.

1. Online registrieren. Bitte registrieren Sie Ihr neues Music Tribe-Gert direkt nach dem Kauf auf der Website musictribe.com. Wenn Sie Ihren Kauf mit unserem einfachen online Formular registrieren, knnen wir Ihre Reparaturansprche schneller und effizienter bearbeiten. Lesen Sie bitte auch unsere Garantiebedingungen, falls zutreffend.

2. Funktionsfehler. Sollte sich kein Music Tribe Hndler in Ihrer Nhe befinden, knnen Sie den Music Tribe Vertrieb Ihres Landes kontaktieren, der auf musictribe.com unter Support aufgefhrt ist. Sollte Ihr Land nicht aufgelistet sein, prfen Sie bitte, ob Ihr Problem von unserem Online Support gelst werden kann, den Sie ebenfalls auf musictribe.com unter Support finden. Alternativ reichen Sie bitte Ihren Garantieanspruch online auf musictribe.com ein, BEVOR Sie das Produkt zurcksenden.

3. Stromanschluss. Bevor Sie das Gert an eine Netzsteckdose anschlieen, prfen Sie bitte, ob Sie die korrekte Netzspannung fr Ihr spezielles Modell verwenden. Fehlerhafte Sicherungen mssen ausnahmslos durch Sicherungen des gleichen Typs und Nennwerts ersetzt werden.

1. Registre-se online. Por favor, registre seu novo equipamento Music Tribe logo aps a compra visitando o site musictribe.com Registrar sua compra usando nosso simples formulrio online nos ajuda a processar seus pedidos de reparos com maior rapidez e eficincia. Alm disso, leia nossos termos e condies de garantia, caso seja necessrio.

2. Funcionamento Defeituoso. Caso seu fornecedor Music Tribe no esteja localizado nas proximidades, voc pode contatar um distribuidor Music Tribe para o seu pas listado abaixo de Suporte em musictribe.com. Se seu pas no estiver na lista, favor checar se seu problema pode ser resolvido com o nosso Suporte Online que tambm pode ser achado abaixo de Suporteem musictribe.com. Alternativamente, favor enviar uma solicitao de garantia online em musictribe.com ANTES da devoluo do produto.

3. Ligaes. Antes de ligar a unidade tomada, assegure-se de que est a utilizar a voltagem correcta para o modelo em questo. Os fusveis com defeito tero de ser substitudos, sem qualquer excepo, por fusveis do mesmo tipo e corrente nominal.

1. Registratevi online. Vi invitiamo a registrare il nuovo apparecchio Music Tribe subito dopo averlo acquistato visitando musictribe.com. La registrazione dell'acquisto tramite il nostro semplice modulo online ci consente di elaborare le richieste di riparazione in modo pi rapido ed efficiente. Leggete anche i termini e le condizioni della nostra garanzia, qualora applicabile.

2. Malfunzionamento. Nel caso in cui il rivenditore autorizzato Music Tribe non si trovi nelle vostre vicinanze, potete contattare il Music Tribe Authorized Fulfiller per il vostro paese, elencato in Support @ musictribe.com. Se la vostra nazione non elencata, controllate se il problema pu essere risolto tramite il nostro Online Supportche pu anche essere trovato sotto Support @ musictribe.com. In alternativa, inviate una richiesta di garanzia online su musictribe.com PRIMA di restituire il prodotto.

3. Collegamento allalimentazione. Prima di collegare l'unit a una presa di corrente, assicuratevi di utilizzare la tensione di rete corretta per il modello specifico. I fusibili guasti devono essere sostituiti, senza eccezioni, con fusibili dello stesso tipo e valore nominale.

Important information

Aspectos importantes

Informations importantes

Weitere wichtige Informationen

Outras Informaes Importantes

Informazioni importanti

1. Registreer online. Registreer uw nieuwe Music Tribe-apparatuur direct nadat u deze hebt gekocht door naar musictribe.com te gaan. Door uw aankoop te registreren via ons eenvoudige online formulier, kunnen wij uw reparatieclaims sneller en efficinter verwerken. Lees ook de voorwaarden van onze garantie, indien van toepassing.

2. Storing. Mocht uw door Music Tribe geautoriseerde wederverkoper niet bij u in de buurt zijn gevestigd, dan kunt u contact opnemen met de door Music Tribe Authorized Fulfiller voor uw land vermeld onder Support op musictribe.com. Als uw land niet in de lijst staat, controleer dan of uw probleem kan worden opgelost door onze "Online Support", die u ook kunt vinden onder "Support" op musictribe.com. U kunt ook een online garantieclaim indienen op musictribe.com VOORDAT u het product retourneert.

3. Stroomaansluitingen. Voordat u het apparaat op een stopcontact aansluit, moet u ervoor zorgen dat u de juiste netspanning voor uw specifieke model gebruikt. Defecte zekeringen moeten zonder uitzondering worden vervangen door zekeringen van hetzelfde type en dezelfde waarde.

1. Registrera online. Registrera din nya Music Tribe-utrustning direkt efter att du kpt den genom att beska musictribe.com. Att registrera ditt kp med vrt enkla onlineformulr hjlper oss att behandla dina reparationsansprk snabbare och mer effektivt. Ls ocks villkoren i vr garanti, om tillmpligt.

2. Fel. Om din Music Tribe-auktoriserade terfrsljare inte finns i din nrhet kan du kontakta Music Tribe Authorized Fulfiller fr ditt land listat under Support p musictribe.com. Om ditt land inte r listat, kontrollera om ditt problem kan hanteras av vr Onlinesupport som ocks finns under Support p musictribe.com. Alternativt kan du skicka in ett online-garantiansprk p musictribe. com INNAN du returnerar produkten.

3. Strmanslutningar. Innan du ansluter enheten till ett eluttag, se till att du anvnder rtt ntspnning fr just din modell. Felaktiga skringar mste bytas ut mot skringar av samma typ och mrkning utan undantag.

1. Zarejestrowa online. Zarejestruj swj nowy sprzt Music Tribe zaraz po zakupie na stronie musictribe.com. Zarejestrowanie zakupu za pomoc naszego prostego formularza online pomaga nam szybciej i efektywniej rozpatrywa roszczenia dotyczce naprawy. Przeczytaj rwnie warunki naszej gwarancji, jeli dotyczy.

2. Awaria. Jeli Twj autoryzowany sprzedawca Music Tribe nie znajduje si w pobliu, moesz skontaktowa si z autoryzowanym dostawc Music Tribe dla swojego kraju, wymienionym w sekcji Wsparcie na stronie musictribe.com. Jeli Twojego kraju nie ma na licie, sprawd, czy Twj problem moe zosta rozwizany przez nasze Wsparcie online, ktre mona rwnie znale w sekcji Wsparcie na stronie musictribe.com. Alternatywnie, przelij zgoszenie gwarancyjne online na musictribe.com PRZED zwrotem produktu.

3. Poczenia zasilania. Przed podczeniem urzdzenia do gniazdka sieciowego upewnij si, e uywasz odpowiedniego napicia sieciowego dla danego modelu. Wadliwe bezpieczniki naley bez wyjtku wymieni na bezpieczniki tego samego typu i wartoci.

Belangrijke informatie

Viktig information

Wana informacja

28 ULTRATONE K3000FX/K1800FX/K900FX/K450FX Quick Start Guide 29

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible Party Name: Music Tribe Commercial NV Inc.

Address: 122 E. 42nd St.1, 8th Floor NY, NY 10168, United States

Email Address: legal@musictribe.com

ULTRATONE K3000FX/K1800FX/K900FX/K450FX

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important information:

Changes or modifications to the equipment not expressly approved by Music Tribe can void the users authority to use the equipment.

Hereby, Music Tribe declares that this product is in compliance with Directive 2014/35/EU,Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/ EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2

Manualsnet FAQs

If you want to find out how the K450FX Behringer works, you can view and download the Behringer K450FX Quick Start Guide on the Manualsnet website.

Yes, we have the Quick Start Guide for Behringer K450FX as well as other Behringer manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Start Guide should include all the details that are needed to use a Behringer K450FX. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Behringer K450FX Quick Start Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Behringer K450FX Quick Start Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Behringer K450FX Quick Start Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Behringer K450FX Quick Start Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Behringer K450FX Quick Start Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.