Barska AX12760 Safe User Manual PDF

1 of 2
1 of 2

Summary of Content for Barska AX12760 Safe User Manual PDF

Getting Started

1. Remove safe from packaging and remove Manual and all accessories that came with the safe. 2. Insert emergency key into key access and turn clockwise; move handle to unlock position and open the safe. Remove key and keep in a secure location. 3. Open battery compartment and insert 4 AA batteries. Do not mix old and new batteries. 4. Press 0 on keypad to wake up the safe and place any finger on scanner. Few beeps will be heard and red flashes will be seen then safe will unlock, turn handle to unlocked position to open the door.

Note: Safe is in Factory Default Mode: ANY Fingerprint can open the safe.

Fingerprint Registration

1. With safe open press and release initialization button located inside the safe and place desired finger on fingerprint scanner.

Successful Registration 2 beeps will be heard and 2 green flashes will be seen.

Unsuccessful Registration 2 quick beeps will be heard along with red flash. See reverse side for more information

6/19 BC611

WARNING

Test Registered Fingerprint

1. With Safe door open, turn handle to lock position extending the bolts out.

2. Press 0 to wake up safe and place Registered Fingerprint on the scanner. If green light is seen when safe can be unlocked then registration was successful. If safe opens but several beeps and red flash is seen then registration was unsuccessful. Follow steps under Fingerprint Registration to register your desired fingerprint.

Pin Code Registration

1. Enter Current Pin Code (Default Pin Code: 12312312312); Green lights will be seen, then press the 3 on keypad.

2. Enter new desired Pin Code between 4 11 digits and if Pin Code is between 4 10 digits, press initialization button on the back of the safe to finish. 1 long beep will be heard and green light will be seen.

Note: Pin Code CANNOT start with 0

Test Registered Pin Code

1. With Safe door open, turn handle to lock position extending the bolts out.

2. Enter Registered Pin Code, If safe unlocks then registration was successful. If safe does not unlock then registration was unsuccessful, please follow steps under Pin Code Registration to register your pin code.

Close / Open Safe Door

Open Safe Door with Fingerprint

Press 0 on keypad to wake up the safe and place registered finger on scanner. Turn handle to unlocked position and open safe door.

Open Safe Door with Pin Code

Enter Registered Pin Code and turn handle to unlocked position to open safe door. Closing Safe Door

Close door and turn handle to lock position to lock the safe.

Manual for Biometric Keypad Safe Read all instructions before using this safe

H F

G

I

E

A

B

2019 BARSKA 855 Towne Center Drive | Pomona, CA 91767

(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com

A. Initialization Button B. Battery Compartment C. Bolts D. Handle E. Emergency Key Access F. Fingerprint Scanner G. Indicator Lights H. Key Pad I. External Battery Source

* Actual model may vary

C D

Lock

Unlock

- Safe can be opened by either Fingerprint, PIN code, and/or Emergency Keys.

- If user resets the safe to Factory Default mode: ANY fingerprint and Factory Default PIN code can open the safe.

- Register BOTH Fingerprint and PIN code to disable factory default mode.

- Register at least two different fingerprints and test a few times before closing the safe door.

- To improve fingerprint accuracy, please register the same finger 5 different times; please remove finger after each successful registration

- Test with a non-registered fingerprint. If the safe opens, the safe is still in Factory Default mode.

- Avoid leaving safe door open and unattended; it will allow unauthorized individuals to add their fingerprints and/or reprogram the safe, gaining full access to the safe and the contents.

- Test the Emergency Keys and store them in a secure place, NOT inside of the safe.

- To maximize the security and performance of the safe, test registered fingerprints every 6 months.

- Test and make sure the safe works properly before mounting.

- Mount the safe before use, the safe may tip forward if not properly mounted.

- Keep children away from safe; they should not play with or around the safe at anytime. Children at play could accidentally get locked inside the safe or accidentally pull on the safe door causing safe to tip over if not properly mounted.

- Failure to follow these warnings could result in serious injury or death.

9V Battery Not Included

Silent Mode

Sound Off

Press and hold initialization button until 1 beep is heard along with green flash. Sound is now disabled.

Sound On

Press and hold initialization button until 1 beep is heard along with green flash.

Resetting the Safe

Take all the batteries out of the safe, press and hold the initialization button inside the safe while re-inserting the batteries, keep holding initialization button until 3 beeps are heard and green flash is seen.

Test Safe to See if it is Reset

With Fingerprint Press 0 on keypad and place any fingerprint on fingerprint scanner. Few beeps will be heard and red flashes will be seen, safe will unlock. Turn handle to unlocked position to open safe.

With Pin Code Press 12312312312 on keypad, beep will be heard and green flash will be seen, safe will unlock. Turn handle to unlocked position to open safe.

ANY fingerprint can now open the safe. Default Pin Code 12312312312

Low Battery Warning

An alarm sound and red flash will be seen when trying to access safe. Safe may allow access still, but batteries should be replaced as soon as possible.

Note: Can use 9v battery as an external power source. Place 9v battery under fingerprint module, touching the metal contacts under the fingerprint module. Safe should power up, if not switch the polarity of the 9v battery.

Care and Maintenance

- To maximize the security and performance of the safe, keep Fingerprint Scanner clean; use a dry cloth to remove any smudges or prints off the Fingerprint Scanner after each use.

- Test registered fingerprints and PIN code every 6 months.

- Keep liquids away from the control panel. Spills on the control panel will cause damage and possibly electric shock.

- Secure safe in a proper area to prevent from falling and causing damage or injury.

- DO NOT disassemble the product. For all repairs, contact BARSKA Customer Service.

- DO NOT use chemicals or cleaning agents to clean the safe.

Mounting Instructions

The safe may be mounted to a wall or floor. Be aware of the load bearing. Failure to do so can result in personal injury and/or damage to property. Use appropriate tools when performing work and always use eye protection.

Wall Mounting

Do not mount the safe without anchoring to the wall.

- Find the studs in the wall, at your desired location. Most studs are 16 inches or 24 inches apart.

- Check the wall for concealed wires or pipes.

- Measure the location of the pre-set drill holes; mark their exact position onto the wall ensuring that the studs or anything else behind will not interfere.

- Drill the appropriate size holes for the anchors you are using.

- Carefully press the anchor into the holes at this time.

- Mount the safe by running screws from inside of the safe and securing to anchors; ensure the safe is mounted securely.

Floor Mounting

- Use proper drill tools depending on the type of floor you are mounting the safe (wood, tile, or concrete).

- Measure the location of the pre-set drill holes; mark their exact position onto the floor.

- Drill the appropriate size holes for the anchors you are using.

- Carefully press the anchor into the holes at this time.

- Mount the safe by running screws from inside of the safe and securing to anchors; ensure the safe is mounted securely.

Biometric Keypad Safe

1 YEAR LIMITED WARRANTY

BARSKA warrants this new safe to be free of original defects in material and/or workmanship under normal use for a period of twelve (12) months from the date product is received by purchaser. This warranty does not include damage caused by improper installation or maintenance. Damage from misuse, abuse, accident (such as dropping), normal wear and tear, fire, flood, or acts of nature. Damage from service or repairs other than those performed by BARSKA. Labor, cost and shipping charges for the removal and replacement of defective parts beyond the initial twelve-month warranty period. All transportation and shipping charges. Removing or altering the seal under any circumstances will automatically void the warranty.

This warranty is limited to original purchaser and is not transferable. This warranty applies only to products purchased in the United States.

Please email info@barska.com or call 1.888.666.6769 for Return Merchandise Number (RMA#) before any returns. The RMA number must appear on the outside of the shipping package. Product must be packed carefully and sturdily in its original packaging to prevent damage in transit and returned freight pre-paid to:

BARSKA OPTICS Repair Department

855 Towne Center Drive Pomona, CA 91767

Please include all of the following when returning BARSKA products for service and/or replacement: 1. Please write your complete details (Name, Address, Telephone #, E-mail address, RMA#, etc.) 2. Purchase receipt or Proof of Purchase. (Original/Copy) 3. A brief explanation of the defect. 4. A Check/Money Order to cover inspection, shipping and handling. Charges are as follows $60 - Standard $90 - Large *Please allow 6-8 weeks for delivery.

BARSKA will examine and test returned product and repair or replace defective part(s) or units with new part(s) or a new unit if necessary within the warranty period. Purchaser is required to remit amount above to BARSKA for return shipping and handling at time product is returned. If repair is required after warranty period expiration, purchaser will be charged for replacement parts and return shipping.

BARSKA Optics shall not be liable for any consequential, incidental and/or contingent damages whatsoever. We will not pay

Manualsnet FAQs

If you want to find out how the AX12760 Barska works, you can view and download the Barska AX12760 Safe User Manual on the Manualsnet website.

Yes, we have the User Manual for Barska AX12760 as well as other Barska manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Barska AX12760. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Barska AX12760 Safe User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Barska AX12760 Safe User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Barska AX12760 Safe User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Barska AX12760 Safe User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Barska AX12760 Safe User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.