Balboa Micro Jet Installation Instructions PDF

1 of 2
1 of 2

Summary of Content for Balboa Micro Jet Installation Instructions PDF

BWG Micro Cyclone Jet Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

(cont. other side)

Cut a hole in the spa wall for the jet. 1. a. Cut a 2.125 diameter hole in the spa wall.

Position the gasket on the jet body, see Figure 1. 2.

Note Silicone is required with the at gasket design. Silicone is optional for use with the L gasket design.

Insert the jet body through the hole in the spa. Make sure the gasket is at and not crimped around the hole. 3.

Place the compensation spacer on the jet body with the at side of the spacer against the back of spa wall. 4.

Thread the nut onto the body. The compensation spacer will center on the nut as it is tightened. 5. a. Be sure the plumbing ports are adjusted to the desired position and tighten the nut hand-tight.

Note To remove the barrel assembly, rotate in a counter clockwise direction until it stops. Using additional force, continue to rotate the barrel assembly past the stop while pulling it out from the body.

Torque the nut to a maximum setting of 9 foot pounds. BWG has an installation tool for tightening the nut that is used with 6. a customer supplied torque wrench. It can be ordered through BWG customer service.

Make the plumbing glue connections to the jet body. Be sure that glue is not allowed to run into the jet body. 7.

Install the barrel assembly into the jet body by inserting and rotating the barrel until it snaps into place. It will rotate freely 8. left and right to the stop.

CAUTION Do not over tighten as this may cause damage to parts and leakage may occur.

There should be plenty of room for the compensating ring to freely oat as the nut is tightened. If this ring is obstructed in any way, it will lose its effectiveness resulting in excessive and unequal force on the sealing ange.

This may cause damage to parts and leakage may occur.

971400 Rev. B October 13, 2009

Figure 1

SAVE THESE INSTRUCTIONS

BWG Micro Cyclone Jet Application Recommendations

This state-of-the-art Micro Cyclone Jet technology features several unique and patent pending installation features.

Thoroughly read and understand these application recommendations before installing this jet.

While installation is simple, there are many variables with each spa manufacturers process that are beyond our control. Therefore we STRONGLY RECOMMEND that every OEM thoroughly test the application of this jet before using it on their production line.

The unique design feature of the Micro Cyclone Jet creates a seal at the front (acrylic side) of the spa.

There are advantages to sealing at the front of the spa.

Acrylic is an optimal sealing smooth surface, much better than berglass.

Potential leaks, or berglass delamination can be prevented by preventing possible water migration.

To fully gain these advantages, the mounting surface must be at!

Each OEM should carefully survey every jet recess. A at sealing area 4 inches in diameter is required. Ensure the cove which is formed at the bottom of a jet recess is fully drawn down and not allowed to drift into the jet sealing area. The hole must be drilled in the center of the recessed area. The sealing area must be consistently at.

Examine the drilling process. The hole must be drilled no larger than 2.125.

Do not allow the hole saw to work or walk during drilling! This could produce a hole that is off center, or not round. Also, the walls of the hole could be incorrectly cut on an angle. Ensure the hole saw is sharp. A dull saw will create excessive heat. Excessive heat will cause the acrylic to curl up at the edge of the h

Manualsnet FAQs

If you want to find out how the Slimline Air Control 10-2310 Balboa works, you can view and download the Balboa Micro Jet Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for Balboa Slimline Air Control 10-2310 as well as other Balboa manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a Balboa Slimline Air Control 10-2310. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Balboa Micro Jet Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Balboa Micro Jet Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Balboa Micro Jet Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Balboa Micro Jet Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Balboa Micro Jet Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.