Balboa Ozone Installation Manual PDF

1 of 2
1 of 2

Summary of Content for Balboa Ozone Installation Manual PDF

WIRINGANDINSTALLATIONINSTRUCTIONS

Power Cords

Air Inlet (near power cord)

Check Valve

Ozone Injector

Water Flow

Water Level in Hot Tub

ai r f low

W at

er Flow

21545_A.pdf 02/06/2006

Possible 240V Wiring

W

G R B

Possible 120V Wiring

R

G W B

Wiring and Installation Instructions Ozone by Balboa is the most reliable and exible system on the market. The unit can be easily adapted to operate at 120 or 240 volts and with any of the required AMP connector pin positions.

Whenever possible, it is best to use the old ozone generator as your guide for installing the connector on the new Balboa ozonator. Be careful with the orientation of the connector and notice the at sides on the outer two prongs. Generally black and white wires used on the old unit will indicate 120V operation and Black and Red wires will indicate 240V operation. Conrm this with markings on the old unit and the wiring diagram inside the system box. The wires are usually visible on the inside of the box and can be used as a guide but should not be totally relied on for voltage indication.

Another method is to measure the voltage from the ozone output of the system with a voltmeter. This will require the system to be on and the ozone output to be energized. This will also require at least one pump to be running and/or a lter cycle to be activated. Use a voltmeter to determine if the ozone connector delivers 120 or 240V.

WARNING: High voltage would be present during this operation. Use extreme caution, especially if the system box is open.

NOTE: In order to extend the life of the Balboa Ozone Generator, it is recommended that it only run when the ltration pump is running. Bear in mind that the ozone produced is only useful when this pump is running. If the ozone wiring is designed to constantly run an ozone generator, TURN THE SYSTEM POWER OFF AT THE BREAKER and use the blue IDC connectors to wire the ozone connector in the box to the ltration pump leads. Use the wiring diagram in the system to verify these leads. Be sure you wire the new Balboa Ozone Generator so it uses the same voltage as the ltration pump.

CAUTION: Once the pins are installed, they cannot be removed without a special tool. Be sure you are positive about the wire positions before installing the connector. Mis-wiring the unit will void its warranty.

It may be helpful to plug in the empty AMP connector to the system ozone output before attaching the wires in order to verify wire positions. Remove the empty connector and install the pins as described below.

Installing the pins is simple. Just push them into the back of the empty AMP connector and you will feel them click into position. A slight tug is all that is needed to be sure the terminal is seated.

For 240 volt installation: black (line), red (line), open (no pin) green (ground), would be a typical order.

A 240 volt installation will not utilize the white wire. Install that pin into the OPEN (no pin) position in the new connector.

For 120 volt installation: black (line), open (no pin), white (neutral), green (ground), would be a typical order.

A

Manualsnet FAQs

If you want to find out how the Slimline Air Control 10-2310 Balboa works, you can view and download the Balboa Ozone Installation Manual on the Manualsnet website.

Yes, we have the Installation Manual for Balboa Slimline Air Control 10-2310 as well as other Balboa manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Manual should include all the details that are needed to use a Balboa Slimline Air Control 10-2310. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Balboa Ozone Installation Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Balboa Ozone Installation Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Balboa Ozone Installation Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Balboa Ozone Installation Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Balboa Ozone Installation Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.