Aztech ASF883 Fan User Manual PDF

1 of 16
1 of 16

Summary of Content for Aztech ASF883 Fan User Manual PDF

ASF883 Aztech 16 Stand Fan

USER MANUAL

PLEASE KEEP THIS USER MANUAL FOR FUTURE USE.

USER MANUAL CONTENTS SAFETY INSTRUCTIONS.......................................................................3

PACKAGE CONTENTS.......................................................................5

APPLIANCE OVERVIEW.....................................................................5

ASSEMBLING THE STAND...................................................................8

ASSEMBLING THE FAN.......................................................................9

USING THE APPLIANCE....................................................................10

CLEANING & MAINTENANCE.........................................................13

TECHNICAL SPECIFICATIONS..........................................................14

SAFETY INSTRUCTIONS Ensure that the appliance and all of its parts and components are

properly assembled, prepared, and locked into place. Ensure to ALWAYS position your Stand Fan on a smooth, dry, and

stable ground. Placing the appliance on unstable surfaces such as cushioned carpets and/or uneven surfaces may cause the appliance to lose its balance during operation.

Before use, please check if the power voltage of your Stand Fan correctly corresponds to your homes power supply.

Always ensure that the fan rings clip is tightly holding the front and rear fan grills in place.

Do not use wet hands in operating the Stand Fan and/or in inserting or removing its power adapter to prevent electrical shocks. It is recommended that you thoroughly dry your hands first before using your Stand Fan or its remote control.

Unplug the power adapter if you are done using your stand fan or before doing any cleaning, relocation, or appliance maintenance.

If the remote control would not be used for long periods of time, remove the remote controls battery.

3

4

When unplugging the power adapter, do not pull or tug its cord. Hold the power adapter properly on its base when unplugging it from the power outlet. Also, ensure that its power cord is kept away from any source of heat or sharp edges that could cause external damage to the cord.

Should damages be found in the appliance, please do not use the appliance and immediately bring it to the Aztech Service Center for repair or replacement.

Your Aztech Stand Fan is not intended for people with reduced physical, sensory or mental capabilities, and/or lack of experience or knowledge. Constant supervision (from a person responsible for their safety) should be provided if such individuals would be using, cleaning, or operating, the appliance.

5

Main Body Fan Blade Fan Stand Fan Base

PACKAGE CONTENTS Front Grill Rear Grill Remote Control

COMPONENTS

Easy Start Guide User Manual Warranty Policy

APPLIANCE OVERVIEW

FRONT GRILL

HOOP

FAN BLADE CAP

FAN BLADE

GRILL NUT

REAR GRILL

FAN MOTOR/ FAN HEAD

CONTROL PANEL

SCREW

INNER TUBE

OUTER TUBE

TUBE CAP

BASE CAP

FAN BASE

BASE NUT BASE SCREW

6

FAN CONTROL PANEL

FAN BUTTONS ON/SPEED Press this button to turn ON the fan. Subsequent presses: LOW MEDIUM HIGH. OSC. Press this button to enable or disable the 4-Way Fan Oscillation (horizontally and vertically). First press: Horizontal oscillation Second press: Vertical oscillation Third press: Horizontal and vertical oscillation Fourth press: Disable Fan Oscillation OFF Press this button to turn OFF the fan.

LED DISPLAY 1/2/3 Displays the currently selected fan speed: 1 (LOW), 2 (MEDIUM) or 3 (HIGH).

7

REMOTE CONTROL

ON/SPEED Press this button to turn ON the fan. Subsequent presses: LOW MEDIUM HIGH. TIMER Press this button repeatedly until the preferred operation time (0.5h, 1h, 2h, or 4h) is selected. MODE Press this button repeatedly to shift between the three blowing modes of the fan: (1) Normal (default when turned on), (2) Natural, and (3) Sleep (please see the Knowing and Changing the Modes section). OSC. Press this button to enable or disable the 4-Way Fan Oscillation (horizontally and vertically). First press: Horizontal oscillation Second press: Vertical oscillation Third press: Horizontal and vertical oscillation Fourth press: Disable Fan Oscillation OFF Press this button to turn OFF the fan.

TIPS IN USING THE REMOTE CONTROL Ensure to insert two (2) AAA batteries in the Remote Controls

battery compartment while observing the correct polarity. NOTE: Incorrect battery installation may damage the Remote Control and/or cause unexpected operation failures.

In using the remote control, ensure that you are 5 meters near the Stand Fan and that the remote control is properly aimed at your stand fans front panel.

8

ASSEMBLING THE STAND

STEP 1 Attach the Outer Tube and Base Cap to the Fan Base.

STEP 2 Using the Base Nut and Base Screw, fasten the Fan Base tightly to the Outer Tube.

STEP 3 Loosen the Height Adjustment Ring and pull out the Inner Tube until the desired fan height is achieved.

TIPS BEFORE ASSEMBLING THE FAN Ensure to unpack the fan and its components. Remove the Fan Blade Cap and the Grill Nut from the motor shaft. Remove the Base Nut and Base Screw from the Outer Tube.

STEP 4 You may then fasten the Height Adjustment Ring to tightly clamp the Inner Tube with the desired height in place. NOTE: Ensure that the Height Adjustment Ring is solidly fastened before assembling the fan motors components.

STEP 5 Ease in the Main Body into the Outer Tube and fasten the Main Body Lock to hold it in place.

9

ASSEMBLING THE FAN STEP 1 On the Fan Motor, position the Rear Grill with the Fan Handle facing up. Ensure that the Rear Grill is stably positioned into the grooves of the Fan Motor.

STEP 2 Using the Grill Nut, fasten the Rear Grill by turning it clockwise until the Rear Grill is securely fastened into place.

STEP 3 Install the Fan Blade by mounting it into the Motor Shaft. Ensure that the Fan Blade has securely reached the motor shafts retaining pins.

STEP 4 With the Fan Blade in place, fit the Fan Blade Cap into the motor shaft and turn it counter clockwise to tightly lock in the Fan Blade into the motor shaft.

STEP 5 Attach the Front Grill by easing it properly against the Rear Grill.

STEP 6 Use the Fan Grill Clip, securely lock in both grills in place.

10

USING THE APPLIANCE

STEP 1 Correctly assemble the fan as shown on the Stand Fan Assembly section.

STEP 2 Position the fan on a smooth and stable ground and plug its power adapter to a power outlet.

STEP 4 Press the ON/SPEED button to turn ON the fan. NOTE: By default, the speed is set to LOW. Upon setting your preferred speed (e.g. high), and turning it OFF and ON again, the fan would resume using the previously selected speed (e.g. high).

ADJUST HEAD TILT

TIPS BEFORE USING THE FAN Before use, please check if the power voltage of the fan correctly

corresponds to your homes power supply. If the remote control would not be used for long periods of time,

remove the remote controls battery. Should damages be found in the appliance, please do not use

the appliance and immediately bring it to the Aztech Service Center for repair or replacement.

ASSEMBLE AS REQUIRED

STABLE GROUND

2 METERS

NOTE: Ensure that there are no objects within 2 meters of the fans head that may hinder its oscillation / swing feature.

STEP 3 Firmly lower or raise the fans head angle until you get the desired fan head angle.

11

STEP 1 Correctly assemble the fan as shown on the Stand Fan Assembly section.

STEP 2 Using your other hand, loosen the Height Adjustment Ring.

ADJUSTING THE FANS HEIGHT

STEP 3 Slowly lower or raise the Main Body until the desired height is achieved and tighten the Height Adjustment Ring to hold it in place.

BLOWING MODES Your Stand Fan has three (3) Blowing Modes for you to choose from.

Each mode would either use a constant speed setting (e.g. Low while ON), or is preprogrammed with interval-based speed changing (e.g. Low Medium - Low speed using 5 second interval).

To change between modes, simply press the MODE button on your remote control repeatedly until the desired mode is selected.

KNOWING AND CHANGING THE MODES

12

NORMAL MODE Uses one (1) speed setting (e.g. LOW) throughout the operation.

NATURAL MODE Depending on your initially selected speed, the Natural Mode automatically changes speed using a regular set of intervals. NOTE: Starting speed depends on your initially selected speed (e.g. LOW speed would enable LOW NATURAL SPEED).

SLEEP MODE Depending on your initially selected speed, the Sleeping Mode automatically decreases the speed using 30 minute intervals until it reaches LOW speed setting.

NOTE: Speed decline rate depends on your initially selected speed (e.g. if MEDIUM speed has been selected, it would only take 30 minutes to reach LOW speed).

13

CLEANING & MAINTENANCE

Remove the fan components and clean each component using a damp cloth.

For the Main Body, use a dry cloth to wipe off dust from its surface.

CLEANING

TIPS BEFORE CLEANING / MAINTENANCE Your Aztech Stand Fan is not intended for people with reduced

physical, sensory or mental capabilities, and/or lack of experience or knowledge. Constant supervision (from a person responsible for their safety) should be provided if such individuals would be using, cleaning, or operating, the appliance.

Unplug the power adapter of your Stand Fan before doing any cleaning, relocation, or appliance maintenance.

Add a few drops of lubricant or oil on the motor shafts base to extend motor life.

MAINTENANCE

14

TECHNICAL SPECIFICATIONS Motor 100% full copper with heat protection

Motor Size 74mm x 16mm

Fan Grill 1.4mm wire diameter

Power Consumption 60W

Timer 450 minutes

Blade 5-piece AS transparent blades

Manualsnet FAQs

If you want to find out how the ASF883 Aztech works, you can view and download the Aztech ASF883 Fan User Manual on the Manualsnet website.

Yes, we have the User Manual for Aztech ASF883 as well as other Aztech manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a Aztech ASF883. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Aztech ASF883 Fan User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Aztech ASF883 Fan User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Aztech ASF883 Fan User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Aztech ASF883 Fan User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Aztech ASF883 Fan User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.