AVer PTC310N Camera Control Codes Manual PDF

1 of 11
1 of 11

Summary of Content for AVer PTC310N Camera Control Codes Manual PDF

AI Auto Tracking PTZ Camera

PTC310 / PTC310H / PTC310N

PTC310U / PTC330U

Control Codes 2022.8.18

1

Product Introduction

Overview

(4) (5) (6) (7)(8)(9) (10)

(11) (12)

(2) (3)

(1)

USB

(1) Tally Lamp (5) PoE+ IEEE 802.3AT (9) USB 3.0 Port (Type C)

(2) IR Sensor (6) RS232 Port (10) HDMI Port

(3) Power Indicator (7) RS422 Port (11) 3G-SDI Port (*2)

(4) Kensington Lock (8) Audio In(*1) (12) DC Power Jack

(*1)Line input level: 1Vrms (max.).

(*1)Mic input level: 50mVrms (max.); Supplied voltage: 2.5V

(*2)This feature (3G-SDI) is not supported on PTC310H

2

RS232 and RS422 Connection

Connect through the RS232 or RS422 for camera control.

RS232

Laptop

Joystick

RS232(VISCA) cable

(Not inculded)

USB

3

RS232 Port Pin Definition

12

3456

789

Function Mini DIN9

PIN # I/O Type Signal Description

VISCA IN

1 Output DTR Data Terminal Ready

2 Input DSR Data Set Ready

3 Output TXD Transmit Data

6 Input RXD Receiver Data

VISCA OUT

7 Output DTR Data Terminal Ready

4 Input DSR Data Set Ready

8 Output TXD Transmit Data

9 Input RXD Receiver Data

5 --- --- Not connect

RS232 mini DIN9 to mini DIN8 Cable Pin Definition

4

Mini DIN8 Cable Pin Definition

Din8 to D-Sub9 Cable Pin Definition

6 7 8

3 4 5

1 2

15

69

No. Signal

1 DTR

2 DSR

3 TXD

4 GND

5 RXD

6 GND

7 NC

8 NC

5

1 8

RS422

[Note] Use cat5e splitter for multi-camera connection.

Cat5e splitter pin assignment:

12345678

12345678 12345678

Camera

Camera/Joystick Camera/Joystick

RS422 Pin

No. Pin No. Pin

1 TX- 5 TX+

2 TX+ 6 RX+

3 RX- 7 RX-

4 TX- 8 RX+

6

Advanced Setting

Go to Advanced Setting -> Control. Make sure the Camera Address, Baud Rate setting is correct.

OSD Tree

Advanced Setting Audio

Input Type Mic in/Line in

Auto Gain Control OFF/ON

Noise Suppression OFF/Low/Normal

Audio Volume 0 ~ 10

Control

Type RS232/RS422

Protocol VISCA/Pelco-P/ Pelco-D

Camera Address 1~7

Baud Rate 2400/4800/9600/38400

Tracking ON/OFF

7

RS232/422 Visca Command Table

Command Set Command Command Packet Comments On 8x 01 04 00 02 FF

Off 8x 01 04 00 03 FF

Stop 8x 01 04 07 00 FF

Tele(Variable) 8x 01 04 07 2p FF

Wide(Variable) 8x 01 04 07 3p FF

Direct 8x 01 04 47 0p 0q 0r 0s FF

pqrs: Zoom Position

PTC310: 0x0000~0x6f20

PTC330: 0x0110~0x5490

Stop 8x 01 04 08 00 FF

Far (Standard) 8x 01 04 08 02 FF

Near (Standard) 8x 01 04 08 03 FF

Auto Focus 8x 01 04 38 02 FF

Manual Focus 8x 01 04 38 03 FF

One Push 8x 01 04 18 01 FF

Direct 8x 01 04 47 0p 0q 0r 0s FF pqrs: Zoom Position

Auto 8x 01 04 35 00 FF Normal Auto

ATW 8x 01 04 35 04 FF

Indoor 8x 01 04 35 01 FF

Outdoor 8x 01 04 35 02 FF

One Push WB 8x 01 04 35 03 FF One Push WB mode

Manual 8x 01 04 35 05 FF Manual Control mode

One Push 8x 01 04 10 05 FF One Push WB Trigger

Up 8x 01 04 03 02 FF Manual Control of R Gain

Down 8x 01 04 03 03 FF

Up 8x 01 04 04 02 FF Manual Control of B Gain

Down 8x 01 04 04 03 FF

Full Auto 8x 01 04 39 00 FF Automatic Exposure mode

Manual 8x 01 04 39 03 FF Manual Control mode

Shutter Priority 8x 01 04 39 0A FF Shutter Priority Automatic Exposure mode

Iris Priority 8x 01 04 39 0B FF Iris Priority Automatic Exposure mode

Bright 8x 01 04 39 0D FF Bright Mode (Manual control)

Up 8x 01 04 0A 02 FF Shutter Setting

Down 8x 01 04 0A 03 FF

Up 8x 01 04 0B 02 FF Iris Setting

Down 8x 01 04 0B 03 FF

Up 8x 01 04 0C 02 FF Gain Setting

Down 8x 01 04 0C 03 FF

Up 8x 01 04 0D 02 FF Bright Setting

Down 8x 01 04 0D 03 FF

Up 8x 01 04 0E 02 FF Exposure Compensation Amount Setting

Down 8x 01 04 0E 03 FF

On 8x 01 04 33 02 FF Back Light Compensation ON/OFF

Off 8x 01 04 33 03 FF

Reset 8x 01 04 3F 00 pp FF

Set 8x 01 04 3F 01 pp FF

Recall 8x 01 04 3F 02 pp FF

CAM_Menu On/Off 8x 01 06 06 10 FF Display ON/OFF

Up 8x 01 06 01 VV WW 03 01 FF

Down 8x 01 06 01 VV WW 03 02 FF

Left 8x 01 06 01 VV WW 01 03 FF

Right 8x 01 06 01 VV WW 02 03 FF

UpLeft 8x 01 06 01 VV WW 01 01 FF

UpRight 8x 01 06 01 VV WW 02 01 FF

DownLeft 8x 01 06 01 VV WW 01 02 FF

DownRight 8x 01 06 01 VV WW 02 02 FF

Stop 8x 01 06 01 VV WW 03 03 FF

Home 8x 01 06 04 FF

Reset 8x 01 06 05 FF

On 8x 01 04 3D 02 FF Wdr ON/OFF

Off 8x 01 04 3D 03 FF

CAM_MenuEnter 8x 01 7E 01 02 00 01 FF Enter Submenu

Tally Lamp ON 8x 01 7E 01 0A 00 02 FF

Tally Lamp OFF 8x 01 7E 01 0A 00 03 FF

Freeze On 81 01 04 62 02 FF Freeze On Immediately

Freeze Off 81 01 04 62 03 FF Freeze Off Immediately

Preset Freeze On 81 01 04 62 22 FF Freeze On When Running Preset

Preset Freeze Off 81 01 04 62 23 FF Freeze Off When Running Preset

On 8x 01 04 7D 02 FF Auto tracking ON/OFF

Off 8x 01 04 7D 03 FF

CAM_Memory Special Set 8x 01 04 3F 01 pp FF

pp: 0x00 To 0xFF normal preset

pp: 0x5F => Trun on OSD menu

pp: 0xA0 => Full Body

pp: 0xA1 => Upper Body

pp: 0xA2 => Tracking Point

pp: 0xA3 => Switch

pp: 0xA4 => Presenter mode (supported in FW v25 or newer)

pp: 0xA5 => Zone mode (supported in FW v25 or newer)

pp: 0xA6 => Hybrid mode (supported in FW v35 or newer)

Absolute Position Set 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

VV: Pan speed setting 0x01 (low speed) to 0x18 (high speed)

WW: Tilt speed setting 0x01 (low speed) to 0x18 (high speed)

YYYY: Pan Position 8A14 to 762C (CENTER 0000)

ZZZZ: Tilt Position 468B to E898 (Image Flip: OFF) (CENTER 0000)

(Supported in FW v26 or above)

On 8x 01 04 A0 02 FF

Off 8x 01 04 A0 03 FF

On 8x 01 04 A1 02 FF

Off 8x 01 04 A1 03 FF

On 8x 01 04 A2 02 FF

Off 8x 01 04 A2 03 FF

IP+Stream 8x 01 04 A3 00 FF

USB only 8x 01 04 A3 01 FF

NDI only 8x 01 04 A3 02 FF

Streaming only 8x 01 04 A3 03 FF

Reboot On 8x 01 04 A4 FF

On 8x 01 04 A5 02 FF

Off 8x 01 04 A5 03 FF

On 8x 01 04 A6 02 FF

Off 8x 01 04 A6 03 FF

On 8x 01 04 A7 02 FF

Off 8x 01 04 A7 03 FF

Auto Zoom/Tilt preset Set 8x 01 04 A8 pp FF pp: 0x00 To 0xFF normal preset

CAM_Focus

Each 'Far/Near' needs a 'stop'

CAM_Power Power ON/OFF

CAM_Zoom

p=0 (Low) to 7 (High)

pp: Preset Number 0x00~0xFF

CAM_WB

CAM_RGain

CAM_Bgain

CAM_AE

CAM_Shutter

CAM_Iris

CAM_Gain

CAM_Bright

CAM_ExpComp

CAM_Backlight

CAM_Preset

VV: Pan speed setting 0x01 (low speed) to 0x18 (high speed)

WW: Tilt speed setting 0x01 (low speed) to 0x18 (high speed)

CAM_WDR

Freeze

Auto Tracking

Auto zoom

Effective Tracking area

RTMP

Pan-tilt Drive

Video mode

Preset Affects PTZ & Focus Values Only

Relative Zoom Ratio

Auto Tilt

8

Inquiry Command Command Packet Reply Packet Comments y0 50 02 FF On

y0 50 03 FF Off

y0 50 00 FF Auto

y0 50 01 FF In Door

y0 50 02 FF Out Door

y0 50 03 FF One Push WB

y0 50 04 FF ATW

y0 50 05 FF Manual

CAM_RGainInq 8x 09 04 43 FF y0 50 00 00 0p 0q FF pq: R Gain

CAM_BGainInq 8x 09 04 44 FF y0 50 00 00 0p 0q FF pq: B Gain

y0 50 00 FF Full Auto

y0 50 03 FF Manual

y0 50 0A FF Shutter Priority

y0 50 0B FF Iris Priority

y0 50 0D FF Bright

CAM_ShutterPosInq 8x 09 04 4A FF y0 50 00 00 0p 0q FF pq: Shutter Position

CAM_IrisPosInq 8x 09 04 4B FF y0 50 00 00 0p 0q FF pq: Iris Position

CAM_GainPosInq 8x 09 04 4C FF y0 50 00 00 0p 0q FF pq: Gain Position

CAM_BrightPosInq 8x 09 04 4D FF y0 50 00 00 0p 0q FF pq: Bright Position

CAM_ExpCompPosInq 8x 09 04 4E FF y0 50 00 00 0p 0q FF pq: ExpComp Position

y0 50 02 FF Auto Focus

y0 50 03 FF Manual Focus

CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position

zoom_Pos_Inq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqrs: Zoom Position

PT_Pos_Inq 8x 09 06 12 FF y0 50 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF YYYY: Pan Position 8A14 to 762C (CENTER 0000)

ZZZZ: Tilt Position 468B to E898 (Image Flip: OFF) (CENTER 0000)

CAM_Preset Inq 8x 09 04 3F FF y0 50 pp FF Return the last preset number which has been operated pp:01-FF

y0 50 01 FF On

y0 50 00 FF Off

y0 50 01 FF Presenter

y0 50 02 FF Zone

y0 50 03 FF Hybrid

y0 50 01 FF Full body

y0 50 02 FF Upper body

y0 50 02 FF On

y0 50 03 FF Off

y0 50 02 FF On

y0 50 03 FF Off

y0 50 02 FF On

y0 50 03 FF Off

y0 50 02 FF On

y0 50 03 FF Off

y0 50 02 FF Freeze On

y0 50 03 FF Freeze Off

y0 50 02 FF Preset Freeze On

y0 50 03 FF Preset Freeze Off

Firmware version 8x 09 36 69 04 FF y0 50 0p 0q 0r 0s 0t 0u 0v 0w FF fw_ver: p.q.rstu.vw

y0 50 00 FF USB cable plug out

y0 50 01 FF USB cable plug in

y0 50 00 FF UVC stream off

y0 50 01 FF UVC stream on

USB Status 8x 09 36 69 05 FF

UVC Status 8x 09 36 69 06 FF

8x 09 04 35 FF

8x 09 04 00 FF

CAM_AEModeInq 8x 09 04 39 FF

CAM_FocusModeInq 8x 09 04 38 FF

CAM_WBModeInq

CAM_PowerInq

CAM_Tracking status 8x 09 36 69 02 FF

CAM_Tracking_mode 8x 09 36 69 01 FF

CAM_Tracking body size8x 09 36 69 03 FF

CAM_OSD MENU on/off8x 09 7E 04 76 01 FF

CAM_Tally 8x 09 7E 01 0A FF

CAM_WDR mode 8x 09 04 3D FF

CAM_BLC mode 8x 09 04 33 FF

CAM_Live Freeze 8x 09 04 62 01 FF

CAM_Preset Freeze 8x 09 04 62 02 FF

The x value = VISCA Camera ID: 1 to 7 for RS232/RS422 connection.

9

Visca-over-IP Settings

The x value of 8x should be 1 for Visca-over-IP string.

Example for Pan-Left command via IP: 01 00 00 09 00 00 00 01 81 01 06 01 07 07 01 03 FF

10

CGI Command Table

CGI item name URL Command Parameter Name Parameter value Description

Get JPEG /snapshot 1280x720 jpg

Get RTSP stream rtsp://ip/live_st1

Get MJPG http://IP/html/live.html

CGI item name URL Command Parameter Name Parameter value Description

up start /cgi-bin?SetPtzf= 1,0,1&(random)

up end /cgi-bin?SetPtzf= 1,0,2&(random)

down start /cgi-bin?SetPtzf= 1,1,1&(random)

down end /cgi-bin?SetPtzf= 1,1,2&(random)

left start /cgi-bin?SetPtzf= 0,1,1&(random)

left end /cgi-bin?SetPtzf= 0,1,2&(random)

right start /cgi-bin?SetPtzf= 0,0,1&(random)

right end /cgi-bin?SetPtzf= 0,0,2&(random)

zoom_in start /cgi-bin?SetPtzf= 2,0,1&(random)

zoom_in end /cgi-bin?SetPtzf= 2,0,2&(random)

zoom_out start /cgi-bin?SetPtzf= 2,1,1&(random)

zoom_out end /cgi-bin?SetPtzf= 2,1,2&(random)

set preset: /cgi-bin?ActPreset= 1,N&(random) N : position

load preset: /cgi-bin?ActPreset= 0,N&(random) N : position

set preset speed /cgi-bin?Set=preset_speed,3,val val: {min: 1, max: 6}

Absolute Position (Pan) /cgi-bin?Set=ptz_p,3,val val: {min: 2048, mid: 962944, max: 1925888} Follows CGI preset speed

Absolute Position (Tilt) /cgi-bin?Set=ptz_t,3,val val: {min: 2048, mid: 165696, max: 662784} Follows CGI preset speedAbsolute Position

(Zoom) /cgi-bin?Set=ptz_z,3,val val: {min: 2048, mid: 14224, max: 28448} Follows CGI preset speed

exposure value /cgi-bin?Set= img_expo_expo,3,N&(random) value 1 ~ 9 N : value

saturation /cgi-bin?Set= img_saturation,3,N&(random) value 0 ~ 10 N : value

contrast /cgi-bin?Set= img_contrast,3,N&(random) value 0 ~ 4 N : value

Tracking on: /cgi-bin?Set= trk_tracking_on,3,1

Tracking off: /cgi-bin?Set= trk_tracking_on,3,0

Reboot GET(Basic Authentication) /cgi-bin?OnePush=!

Factory Reset GET(Basic Authentication) /cgi-bin?OnePush=d

Mode Presenter /cgi-bin?Set=trk_mode,3,1&X value random number X : value

Mode Zone /cgi-bin?Set=trk_mode,3,2&X value random number X : value

Mode Hybrid /cgi-bin?Set=trk_mode,3,3&X

Mode Get GET(Basic Authentication) /cgi-bin?Get=trk_mode,3&_=X - Reply

Presenter

trk_mode,3=1

Zone

trk_mode,3=2

Hybrid

trk_mode,3=3

X : value

Click Track ON GET(Basic Authentication) /cgi-bin?Set=trk_update_detect,3,1

Click Track OFF GET(Basic Authentication) /cgi-bin?Set=trk_update_detect,3,0

GET(Basic Authentication) /cgi-bin?Get=trk_detect_num,3 Need to be sent along with

Click Track ON command

- Reply "trk_detect_num,3=X\r\n" X: The amount of humanoid outlines,

maximum: 50

GET(Basic Authentication) /cgi-bin?GetTrackingDetectZone=X X: The amount of humanoid outlines,

maximum: 50

- Reply "focus:-1\nzone[00]:00,119,720,960\nzone[01]:-

1502615204,-1366225632,01,-1366223544"

focus - The number of humanoid

outline being tracked.

zone[NN]:x,y,w,h - based on 1080P

resolution

The upper left corner of the screen is the coordinate

reference (0,0), x-coordinate/y-coordinate/w width/h

height, based on the upper left corner of the

humanoid outline.

The number following indicates the number of the

tracked person, for example, -1 means that no one is

being tracked. If one of the three is being tracked,

one of 0, 1 and 2 will appear after the 'focus'.

GET(Basic Authentication) /cgi-bin?Set=trk_assign_zone,3,X X: The number of the human outlines

- Reply http response: ok

GET(Basic Authentication) /cgi-bin?SetString=TrackingFocusZone,[x,y,w,h]

- Reply http response: ok

Tracking On/Off Get GET(Basic Authentication) /cgi-bin?Get=trk_tracking_on,3&_=X - Reply

On

trk_tracking_on,3=1

Off

trk_tracking_on,3=0"

X : value

RTMP Start streamming /cgi-bin?Set= vdo_rtmp_enable,3,1

RTMP Stop streamming /cgi-bin?Set= vdo_rtmp_enable,3,0

Save RTMP server URL /cgi-bin?SaveRtmpUrl= value empty for clearing up the field

Save RTMP stream Key /cgi-bin?SaveRtmpKey= value empty for clearing up the field

Inquiry for RTMP status /cgi-bin?Get=vdo_rtmp_status Streaming: vdo_rtmp_status=2 Stopped:

vdo_rtmp_status=0

Get RTMP server URL /cgi-bin?GetRtmpUrl

Get RTMP stream key /cgi-bin?GetRtmpKey

GET(Basic Authentication) /cgi-bin?Get=usb_status_inquire,3

- Reply "usb_status_inquire,3=X\r\n" X: 0(plug out), 1(plug in)

GET(Basic Authentication) /cgi-bin?Get=uvc_status_inquire,3

- Reply "uvc_status_inquire,3=X\r\n" X: 0(stream off), 1(stream on)

Status get (Modle name

& mac & FW_VER) /cgi-

bin?SetString=sys_name&net_mac&sys_fw_versio

n&_=1635216271678

http://10.100.105.110/cgi-

bin?GetString=sys_name&net_mac&sys_fw_v

ersion&_=1635216271678

Serial No. get /cgi-bin?GetSerialNumber&_=1635216271680 http://10.100.105.110/cgi-

bin?GetSerialNumber&_=1635216271680

USB status

UVC status

Click Track

Get detect zone

(Humanoid outlines)

number

Click Track

Get detect zone

(Humanoid outlines) info

Click Track

Set target zone

CGI List for Video Transmission

CGI List for Camera Control

CGI List for Various Setti

Manualsnet FAQs

If you want to find out how the PTC310N AVer works, you can view and download the AVer PTC310N Camera Control Codes Manual on the Manualsnet website.

Yes, we have the Control Codes Manual for AVer PTC310N as well as other AVer manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Control Codes Manual should include all the details that are needed to use a AVer PTC310N. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the AVer PTC310N Camera Control Codes Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This AVer PTC310N Camera Control Codes Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download AVer PTC310N Camera Control Codes Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print AVer PTC310N Camera Control Codes Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the AVer PTC310N Camera Control Codes Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.