AVer PTC310 Camera Control Codes Manual PDF
Summary of Content for AVer PTC310 Camera Control Codes Manual PDF
AI Auto Tracking PTZ Camera
PTC310 / PTC310H / PTC310N
PTC310U / PTC330U
Control Codes 2022.8.18
1
Product Introduction
Overview
(4) (5) (6) (7)(8)(9) (10)
(11) (12)
(2) (3)
(1)
USB
(1) Tally Lamp (5) PoE+ IEEE 802.3AT (9) USB 3.0 Port (Type C)
(2) IR Sensor (6) RS232 Port (10) HDMI Port
(3) Power Indicator (7) RS422 Port (11) 3G-SDI Port (*2)
(4) Kensington Lock (8) Audio In(*1) (12) DC Power Jack
(*1)Line input level: 1Vrms (max.).
(*1)Mic input level: 50mVrms (max.); Supplied voltage: 2.5V
(*2)This feature (3G-SDI) is not supported on PTC310H
2
RS232 and RS422 Connection
Connect through the RS232 or RS422 for camera control.
RS232
Laptop
Joystick
RS232(VISCA) cable
(Not inculded)
USB
3
RS232 Port Pin Definition
12
3456
789
Function Mini DIN9
PIN # I/O Type Signal Description
VISCA IN
1 Output DTR Data Terminal Ready
2 Input DSR Data Set Ready
3 Output TXD Transmit Data
6 Input RXD Receiver Data
VISCA OUT
7 Output DTR Data Terminal Ready
4 Input DSR Data Set Ready
8 Output TXD Transmit Data
9 Input RXD Receiver Data
5 --- --- Not connect
RS232 mini DIN9 to mini DIN8 Cable Pin Definition
4
Mini DIN8 Cable Pin Definition
Din8 to D-Sub9 Cable Pin Definition
6 7 8
3 4 5
1 2
15
69
No. Signal
1 DTR
2 DSR
3 TXD
4 GND
5 RXD
6 GND
7 NC
8 NC
5
1 8
RS422
[Note] Use cat5e splitter for multi-camera connection.
Cat5e splitter pin assignment:
12345678
12345678 12345678
Camera
Camera/Joystick Camera/Joystick
RS422 Pin
No. Pin No. Pin
1 TX- 5 TX+
2 TX+ 6 RX+
3 RX- 7 RX-
4 TX- 8 RX+
6
Advanced Setting
Go to Advanced Setting -> Control. Make sure the Camera Address, Baud Rate setting is correct.
OSD Tree
Advanced Setting Audio
Input Type Mic in/Line in
Auto Gain Control OFF/ON
Noise Suppression OFF/Low/Normal
Audio Volume 0 ~ 10
Control
Type RS232/RS422
Protocol VISCA/Pelco-P/ Pelco-D
Camera Address 1~7
Baud Rate 2400/4800/9600/38400
Tracking ON/OFF
7
RS232/422 Visca Command Table
Command Set Command Command Packet Comments On 8x 01 04 00 02 FF
Off 8x 01 04 00 03 FF
Stop 8x 01 04 07 00 FF
Tele(Variable) 8x 01 04 07 2p FF
Wide(Variable) 8x 01 04 07 3p FF
Direct 8x 01 04 47 0p 0q 0r 0s FF
pqrs: Zoom Position
PTC310: 0x0000~0x6f20
PTC330: 0x0110~0x5490
Stop 8x 01 04 08 00 FF
Far (Standard) 8x 01 04 08 02 FF
Near (Standard) 8x 01 04 08 03 FF
Auto Focus 8x 01 04 38 02 FF
Manual Focus 8x 01 04 38 03 FF
One Push 8x 01 04 18 01 FF
Direct 8x 01 04 47 0p 0q 0r 0s FF pqrs: Zoom Position
Auto 8x 01 04 35 00 FF Normal Auto
ATW 8x 01 04 35 04 FF
Indoor 8x 01 04 35 01 FF
Outdoor 8x 01 04 35 02 FF
One Push WB 8x 01 04 35 03 FF One Push WB mode
Manual 8x 01 04 35 05 FF Manual Control mode
One Push 8x 01 04 10 05 FF One Push WB Trigger
Up 8x 01 04 03 02 FF Manual Control of R Gain
Down 8x 01 04 03 03 FF
Up 8x 01 04 04 02 FF Manual Control of B Gain
Down 8x 01 04 04 03 FF
Full Auto 8x 01 04 39 00 FF Automatic Exposure mode
Manual 8x 01 04 39 03 FF Manual Control mode
Shutter Priority 8x 01 04 39 0A FF Shutter Priority Automatic Exposure mode
Iris Priority 8x 01 04 39 0B FF Iris Priority Automatic Exposure mode
Bright 8x 01 04 39 0D FF Bright Mode (Manual control)
Up 8x 01 04 0A 02 FF Shutter Setting
Down 8x 01 04 0A 03 FF
Up 8x 01 04 0B 02 FF Iris Setting
Down 8x 01 04 0B 03 FF
Up 8x 01 04 0C 02 FF Gain Setting
Down 8x 01 04 0C 03 FF
Up 8x 01 04 0D 02 FF Bright Setting
Down 8x 01 04 0D 03 FF
Up 8x 01 04 0E 02 FF Exposure Compensation Amount Setting
Down 8x 01 04 0E 03 FF
On 8x 01 04 33 02 FF Back Light Compensation ON/OFF
Off 8x 01 04 33 03 FF
Reset 8x 01 04 3F 00 pp FF
Set 8x 01 04 3F 01 pp FF
Recall 8x 01 04 3F 02 pp FF
CAM_Menu On/Off 8x 01 06 06 10 FF Display ON/OFF
Up 8x 01 06 01 VV WW 03 01 FF
Down 8x 01 06 01 VV WW 03 02 FF
Left 8x 01 06 01 VV WW 01 03 FF
Right 8x 01 06 01 VV WW 02 03 FF
UpLeft 8x 01 06 01 VV WW 01 01 FF
UpRight 8x 01 06 01 VV WW 02 01 FF
DownLeft 8x 01 06 01 VV WW 01 02 FF
DownRight 8x 01 06 01 VV WW 02 02 FF
Stop 8x 01 06 01 VV WW 03 03 FF
Home 8x 01 06 04 FF
Reset 8x 01 06 05 FF
On 8x 01 04 3D 02 FF Wdr ON/OFF
Off 8x 01 04 3D 03 FF
CAM_MenuEnter 8x 01 7E 01 02 00 01 FF Enter Submenu
Tally Lamp ON 8x 01 7E 01 0A 00 02 FF
Tally Lamp OFF 8x 01 7E 01 0A 00 03 FF
Freeze On 81 01 04 62 02 FF Freeze On Immediately
Freeze Off 81 01 04 62 03 FF Freeze Off Immediately
Preset Freeze On 81 01 04 62 22 FF Freeze On When Running Preset
Preset Freeze Off 81 01 04 62 23 FF Freeze Off When Running Preset
On 8x 01 04 7D 02 FF Auto tracking ON/OFF
Off 8x 01 04 7D 03 FF
CAM_Memory Special Set 8x 01 04 3F 01 pp FF
pp: 0x00 To 0xFF normal preset
pp: 0x5F => Trun on OSD menu
pp: 0xA0 => Full Body
pp: 0xA1 => Upper Body
pp: 0xA2 => Tracking Point
pp: 0xA3 => Switch
pp: 0xA4 => Presenter mode (supported in FW v25 or newer)
pp: 0xA5 => Zone mode (supported in FW v25 or newer)
pp: 0xA6 => Hybrid mode (supported in FW v35 or newer)
Absolute Position Set 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
VV: Pan speed setting 0x01 (low speed) to 0x18 (high speed)
WW: Tilt speed setting 0x01 (low speed) to 0x18 (high speed)
YYYY: Pan Position 8A14 to 762C (CENTER 0000)
ZZZZ: Tilt Position 468B to E898 (Image Flip: OFF) (CENTER 0000)
(Supported in FW v26 or above)
On 8x 01 04 A0 02 FF
Off 8x 01 04 A0 03 FF
On 8x 01 04 A1 02 FF
Off 8x 01 04 A1 03 FF
On 8x 01 04 A2 02 FF
Off 8x 01 04 A2 03 FF
IP+Stream 8x 01 04 A3 00 FF
USB only 8x 01 04 A3 01 FF
NDI only 8x 01 04 A3 02 FF
Streaming only 8x 01 04 A3 03 FF
Reboot On 8x 01 04 A4 FF
On 8x 01 04 A5 02 FF
Off 8x 01 04 A5 03 FF
On 8x 01 04 A6 02 FF
Off 8x 01 04 A6 03 FF
On 8x 01 04 A7 02 FF
Off 8x 01 04 A7 03 FF
Auto Zoom/Tilt preset Set 8x 01 04 A8 pp FF pp: 0x00 To 0xFF normal preset
CAM_Focus
Each 'Far/Near' needs a 'stop'
CAM_Power Power ON/OFF
CAM_Zoom
p=0 (Low) to 7 (High)
pp: Preset Number 0x00~0xFF
CAM_WB
CAM_RGain
CAM_Bgain
CAM_AE
CAM_Shutter
CAM_Iris
CAM_Gain
CAM_Bright
CAM_ExpComp
CAM_Backlight
CAM_Preset
VV: Pan speed setting 0x01 (low speed) to 0x18 (high speed)
WW: Tilt speed setting 0x01 (low speed) to 0x18 (high speed)
CAM_WDR
Freeze
Auto Tracking
Auto zoom
Effective Tracking area
RTMP
Pan-tilt Drive
Video mode
Preset Affects PTZ & Focus Values Only
Relative Zoom Ratio
Auto Tilt
8
Inquiry Command Command Packet Reply Packet Comments y0 50 02 FF On
y0 50 03 FF Off
y0 50 00 FF Auto
y0 50 01 FF In Door
y0 50 02 FF Out Door
y0 50 03 FF One Push WB
y0 50 04 FF ATW
y0 50 05 FF Manual
CAM_RGainInq 8x 09 04 43 FF y0 50 00 00 0p 0q FF pq: R Gain
CAM_BGainInq 8x 09 04 44 FF y0 50 00 00 0p 0q FF pq: B Gain
y0 50 00 FF Full Auto
y0 50 03 FF Manual
y0 50 0A FF Shutter Priority
y0 50 0B FF Iris Priority
y0 50 0D FF Bright
CAM_ShutterPosInq 8x 09 04 4A FF y0 50 00 00 0p 0q FF pq: Shutter Position
CAM_IrisPosInq 8x 09 04 4B FF y0 50 00 00 0p 0q FF pq: Iris Position
CAM_GainPosInq 8x 09 04 4C FF y0 50 00 00 0p 0q FF pq: Gain Position
CAM_BrightPosInq 8x 09 04 4D FF y0 50 00 00 0p 0q FF pq: Bright Position
CAM_ExpCompPosInq 8x 09 04 4E FF y0 50 00 00 0p 0q FF pq: ExpComp Position
y0 50 02 FF Auto Focus
y0 50 03 FF Manual Focus
CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position
zoom_Pos_Inq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqrs: Zoom Position
PT_Pos_Inq 8x 09 06 12 FF y0 50 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF YYYY: Pan Position 8A14 to 762C (CENTER 0000)
ZZZZ: Tilt Position 468B to E898 (Image Flip: OFF) (CENTER 0000)
CAM_Preset Inq 8x 09 04 3F FF y0 50 pp FF Return the last preset number which has been operated pp:01-FF
y0 50 01 FF On
y0 50 00 FF Off
y0 50 01 FF Presenter
y0 50 02 FF Zone
y0 50 03 FF Hybrid
y0 50 01 FF Full body
y0 50 02 FF Upper body
y0 50 02 FF On
y0 50 03 FF Off
y0 50 02 FF On
y0 50 03 FF Off
y0 50 02 FF On
y0 50 03 FF Off
y0 50 02 FF On
y0 50 03 FF Off
y0 50 02 FF Freeze On
y0 50 03 FF Freeze Off
y0 50 02 FF Preset Freeze On
y0 50 03 FF Preset Freeze Off
Firmware version 8x 09 36 69 04 FF y0 50 0p 0q 0r 0s 0t 0u 0v 0w FF fw_ver: p.q.rstu.vw
y0 50 00 FF USB cable plug out
y0 50 01 FF USB cable plug in
y0 50 00 FF UVC stream off
y0 50 01 FF UVC stream on
USB Status 8x 09 36 69 05 FF
UVC Status 8x 09 36 69 06 FF
8x 09 04 35 FF
8x 09 04 00 FF
CAM_AEModeInq 8x 09 04 39 FF
CAM_FocusModeInq 8x 09 04 38 FF
CAM_WBModeInq
CAM_PowerInq
CAM_Tracking status 8x 09 36 69 02 FF
CAM_Tracking_mode 8x 09 36 69 01 FF
CAM_Tracking body size8x 09 36 69 03 FF
CAM_OSD MENU on/off8x 09 7E 04 76 01 FF
CAM_Tally 8x 09 7E 01 0A FF
CAM_WDR mode 8x 09 04 3D FF
CAM_BLC mode 8x 09 04 33 FF
CAM_Live Freeze 8x 09 04 62 01 FF
CAM_Preset Freeze 8x 09 04 62 02 FF
The x value = VISCA Camera ID: 1 to 7 for RS232/RS422 connection.
9
Visca-over-IP Settings
The x value of 8x should be 1 for Visca-over-IP string.
Example for Pan-Left command via IP: 01 00 00 09 00 00 00 01 81 01 06 01 07 07 01 03 FF
10
CGI Command Table
CGI item name URL Command Parameter Name Parameter value Description
Get JPEG /snapshot 1280x720 jpg
Get RTSP stream rtsp://ip/live_st1
Get MJPG http://IP/html/live.html
CGI item name URL Command Parameter Name Parameter value Description
up start /cgi-bin?SetPtzf= 1,0,1&(random)
up end /cgi-bin?SetPtzf= 1,0,2&(random)
down start /cgi-bin?SetPtzf= 1,1,1&(random)
down end /cgi-bin?SetPtzf= 1,1,2&(random)
left start /cgi-bin?SetPtzf= 0,1,1&(random)
left end /cgi-bin?SetPtzf= 0,1,2&(random)
right start /cgi-bin?SetPtzf= 0,0,1&(random)
right end /cgi-bin?SetPtzf= 0,0,2&(random)
zoom_in start /cgi-bin?SetPtzf= 2,0,1&(random)
zoom_in end /cgi-bin?SetPtzf= 2,0,2&(random)
zoom_out start /cgi-bin?SetPtzf= 2,1,1&(random)
zoom_out end /cgi-bin?SetPtzf= 2,1,2&(random)
set preset: /cgi-bin?ActPreset= 1,N&(random) N : position
load preset: /cgi-bin?ActPreset= 0,N&(random) N : position
set preset speed /cgi-bin?Set=preset_speed,3,val val: {min: 1, max: 6}
Absolute Position (Pan) /cgi-bin?Set=ptz_p,3,val val: {min: 2048, mid: 962944, max: 1925888} Follows CGI preset speed
Absolute Position (Tilt) /cgi-bin?Set=ptz_t,3,val val: {min: 2048, mid: 165696, max: 662784} Follows CGI preset speedAbsolute Position
(Zoom) /cgi-bin?Set=ptz_z,3,val val: {min: 2048, mid: 14224, max: 28448} Follows CGI preset speed
exposure value /cgi-bin?Set= img_expo_expo,3,N&(random) value 1 ~ 9 N : value
saturation /cgi-bin?Set= img_saturation,3,N&(random) value 0 ~ 10 N : value
contrast /cgi-bin?Set= img_contrast,3,N&(random) value 0 ~ 4 N : value
Tracking on: /cgi-bin?Set= trk_tracking_on,3,1
Tracking off: /cgi-bin?Set= trk_tracking_on,3,0
Reboot GET(Basic Authentication) /cgi-bin?OnePush=!
Factory Reset GET(Basic Authentication) /cgi-bin?OnePush=d
Mode Presenter /cgi-bin?Set=trk_mode,3,1&X value random number X : value
Mode Zone /cgi-bin?Set=trk_mode,3,2&X value random number X : value
Mode Hybrid /cgi-bin?Set=trk_mode,3,3&X
Mode Get GET(Basic Authentication) /cgi-bin?Get=trk_mode,3&_=X - Reply
Presenter
trk_mode,3=1
Zone
trk_mode,3=2
Hybrid
trk_mode,3=3
X : value
Click Track ON GET(Basic Authentication) /cgi-bin?Set=trk_update_detect,3,1
Click Track OFF GET(Basic Authentication) /cgi-bin?Set=trk_update_detect,3,0
GET(Basic Authentication) /cgi-bin?Get=trk_detect_num,3 Need to be sent along with
Click Track ON command
- Reply "trk_detect_num,3=X\r\n" X: The amount of humanoid outlines,
maximum: 50
GET(Basic Authentication) /cgi-bin?GetTrackingDetectZone=X X: The amount of humanoid outlines,
maximum: 50
- Reply "focus:-1\nzone[00]:00,119,720,960\nzone[01]:-
1502615204,-1366225632,01,-1366223544"
focus - The number of humanoid
outline being tracked.
zone[NN]:x,y,w,h - based on 1080P
resolution
The upper left corner of the screen is the coordinate
reference (0,0), x-coordinate/y-coordinate/w width/h
height, based on the upper left corner of the
humanoid outline.
The number following indicates the number of the
tracked person, for example, -1 means that no one is
being tracked. If one of the three is being tracked,
one of 0, 1 and 2 will appear after the 'focus'.
GET(Basic Authentication) /cgi-bin?Set=trk_assign_zone,3,X X: The number of the human outlines
- Reply http response: ok
GET(Basic Authentication) /cgi-bin?SetString=TrackingFocusZone,[x,y,w,h]
- Reply http response: ok
Tracking On/Off Get GET(Basic Authentication) /cgi-bin?Get=trk_tracking_on,3&_=X - Reply
On
trk_tracking_on,3=1
Off
trk_tracking_on,3=0"
X : value
RTMP Start streamming /cgi-bin?Set= vdo_rtmp_enable,3,1
RTMP Stop streamming /cgi-bin?Set= vdo_rtmp_enable,3,0
Save RTMP server URL /cgi-bin?SaveRtmpUrl= value empty for clearing up the field
Save RTMP stream Key /cgi-bin?SaveRtmpKey= value empty for clearing up the field
Inquiry for RTMP status /cgi-bin?Get=vdo_rtmp_status Streaming: vdo_rtmp_status=2 Stopped:
vdo_rtmp_status=0
Get RTMP server URL /cgi-bin?GetRtmpUrl
Get RTMP stream key /cgi-bin?GetRtmpKey
GET(Basic Authentication) /cgi-bin?Get=usb_status_inquire,3
- Reply "usb_status_inquire,3=X\r\n" X: 0(plug out), 1(plug in)
GET(Basic Authentication) /cgi-bin?Get=uvc_status_inquire,3
- Reply "uvc_status_inquire,3=X\r\n" X: 0(stream off), 1(stream on)
Status get (Modle name
& mac & FW_VER) /cgi-
bin?SetString=sys_name&net_mac&sys_fw_versio
n&_=1635216271678
http://10.100.105.110/cgi-
bin?GetString=sys_name&net_mac&sys_fw_v
ersion&_=1635216271678
Serial No. get /cgi-bin?GetSerialNumber&_=1635216271680 http://10.100.105.110/cgi-
bin?GetSerialNumber&_=1635216271680
USB status
UVC status
Click Track
Get detect zone
(Humanoid outlines)
number
Click Track
Get detect zone
(Humanoid outlines) info
Click Track
Set target zone
CGI List for Video Transmission
CGI List for Camera Control
CGI List for Various Setti
Related manuals for AVer PTC310 Camera Control Codes Manual
Manualsnet FAQs
If you want to find out how the PTC310 AVer works, you can view and download the AVer PTC310 Camera Control Codes Manual on the Manualsnet website.
Yes, we have the Control Codes Manual for AVer PTC310 as well as other AVer manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Control Codes Manual should include all the details that are needed to use a AVer PTC310. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the AVer PTC310 Camera Control Codes Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This AVer PTC310 Camera Control Codes Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download AVer PTC310 Camera Control Codes Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print AVer PTC310 Camera Control Codes Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the AVer PTC310 Camera Control Codes Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.