ASUS ZenBeam S2 Projector User Manual PDF

LED projector E-Manual

S2 Series

2 LED projector E-Manual

COPYRIGHT AND WARRANTY INFORMATION

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (ASUS).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the is defaced or missing.

ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Copyright 2019 ASUSTeK COMPUTER INC. All Rights Reserved.

LIMITATION OF LIABILITY

Circumstances may arise where because of a default on ASUS part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the listed contract price of each product.

ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement.

This limit also applies to ASUS suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.

UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.

SERVICE AND SUPPORT

Visit our multi-language web site at https://www.asus.com/support

E14596 First Edition February 2019

LED projector E-Manual 3

Table of Contents About this manual ............................................................................................. 5

Conventions used in this manual ............................................................... 6 Typography ......................................................................................................... 6 Multi-language versions ................................................................................ 6

Safety precautions ............................................................................................. 7 Using your LED projector ............................................................................... 7 Servicing and replacement of parts .......................................................... 7 Caring for your LED projector ...................................................................... 8 Proper disposal .................................................................................................. 8

Chapter 1: Knowing your LED projector Features ...............................................................................................................10

Top view .............................................................................................................10 Front view ..........................................................................................................13 Rear view ...........................................................................................................14 Left side .............................................................................................................16 Right side ...........................................................................................................17 Bottom view .....................................................................................................18 Extended features ..........................................................................................19

LED projector remote control ......................................................................21 Replacing the battery ...................................................................................23

Chapter 2: Setting up Operating your LED projector .....................................................................26

Connect the LED projector to the power adapter ..............................26 Connect the LED projector to your device ............................................29 Adjust the height of the LED projector ...................................................34 Press the power button ................................................................................36 Adjust the image focus .................................................................................37

4 LED projector E-Manual

Chapter 3: Using the onscreen display menu Using your LED projector for the first time .............................................40 Adjusting your LED projector's settings ..................................................41 Onscreen display menu options .................................................................42

Image .............................................................................................................42 Display .............................................................................................................43 Input .............................................................................................................44 System .............................................................................................................45

Turning off your LED projector ....................................................................46 Multi-language versions ..............................................................................47

Appendices Federal Communications Commission Statement .............................50 Regional notice for California .....................................................................51 Global Environmental Regulation Compliance and Declaration .52 ASUS Recycling/Takeback Services ..........................................................52 Specifications for S2 series LED projector ..............................................53 Support PC Timings .......................................................................................55

LED projector E-Manual 5

About this manual This manual provides information about the hardware and software features of your LED projector through the following chapters:

Chapter 1: Knowing your LED Projector

This chapter details the parts of your LED projector and its accompanying remote control.

Chapter 2: Setting up

This chapter shows you how to set up your LED projector and use its parts for input device connection.

Chapter 3: Using the onscreen display menu

This chapter talks about the features of your LED projectors onscreen display menu and how to navigate it using the control panel.

Appendices

This section includes safety notices for your LED projector.

6 LED projector E-Manual

Conventions used in this manual To highlight key information in this manual, some text are presented as follows:

IMPORTANT! This message contains vital information that must be followed to complete a task.

NOTE: This message contains additional information and tips that can help complete tasks.

WARNING! This message contains important information that must be followed to keep you safe while performing tasks and prevent damage to your LED projector's data and components.

Typography Bold = This indicates a menu or an item that must be selected.

Italic = This indicates sections that you can refer to in this manual.

Multi-language versions Download other language versions of this E-Manual via this website: https://www.asus.com/support

LED projector E-Manual 7

Safety precautions Using your LED projector

Refertothemanualandtakenoteofthesafetyinstructions before operating your LED projector.

Followthenotesandwarningsstatedintheusermanual.

DonotplaceyourLEDprojectoronunevenorunstable surfaces.

DonotuseyourLEDprojectorinsmokyenvironments.Smoke residue may cause build-up on critical parts and damage the LED projector or decrease its performance.

KeeptheLEDprojectorsplasticpackagesoutofthereachof children.

DonotblockorplaceanythingneartheLEDprojectors ventilation holes. Doing so may cause internal heat build-up that can degrade picture quality and damage the projector.

EnsurethattheoperatingvoltageofyourLEDprojector matches the voltage of your power source.

Servicing and replacement of parts

DonotdisassembleorattempttoservicethisLEDprojectorby yourself. Contact your local ASUS service center for assistance.

WhenreplacingpartsofyourLEDprojector,purchaseitems as specified by ASUS and contact your local service center for assistance.

8 LED projector E-Manual

Caring for your LED projector

SwitchoffthenunplugtheLEDprojectorfromthepoweroutlet before cleaning it.

WhencleaningtheLEDprojectorshousing,useacleansoft cloth dampened with water or a mix of water and neutral detergent. Wipe it dry using a soft dry cloth.

Ensurethatthelensiscoolbeforecleaningit.Gentlywipethe lens using a lens cleaning paper. Do not touch the lens with your hands.

Donotuseliquidoraerosolcleaners,benzene,orthinnerson your LED projector.

NeveroperatethisLEDprojectorimmediatelyaftermoving it from a cold location. When the LED projector is exposed to a drastic change in temperature, moisture may condense on the lens and its other internal parts. To prevent this, use the unit two (2) hours after an extreme or sudden change in temperature occurs.

Proper disposal

Do not throw your LED projector in municipal waste. This product has been designed to enable proper reuse of parts and recycling. The symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment and mercury-containing button cell battery) should not be placed in municipal waste. Check local regulations for disposal of electronic products.

Do not throw the battery in municipal waste. The symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

LED projector E-Manual 9

Chapter 1: Knowing your LED projector

Chapter 1:

Knowing your LED projector

10 LED projector E-Manual

Features

Top view

LED projector E-Manual 11

Power indicator and battery status indicator This LED indicator indicates the following scenarios for your LED projector:

ItlightsupwhentheLEDprojectorispoweredon.

Itlightsupaseithergreenorreddependingonthe battery charge status.

For details on how this LED indicator functions as a battery status indicator, refer to the following table:

Color Status

Solid Green The LED projector is either plugged to a power source or running on battery mode and the battery power is more than 25%.

Solid Red The LED projector is running on battery mode only and the battery power is not more than 25%.

Battery charge indicator This LED indicator lights up when the LED projector is plugged to a power source using its power adapter.

IMPORTANT! Use only the bundled power adapter to charge the battery pack and supply power to your LED projector.

12 LED projector E-Manual

Control panel buttons These buttons correspond to a specific LED projector setting as indicated below.

Keystone Input Back/Splendid

Joystick This joystick allows you to navigate the onscreen display menu and select menu settings. This joystick also correspond to specific LED projector settings as indicated below.

Open main menu/OK (push center)

Adjust focus (move up or down)

Adjust volume (move left or right)

NOTE: For more information on using your LED projectors settings, refer to the Using the onscreen display menu section in this manual.

LED projector E-Manual 13

Front view

Auto focus camera This camera helps the LED projector with the auto focus feature.

Lens The lens projects video or image files onscreen from your input device.

WARNING! Do not touch the lens using your hands or any sharp object.

14 LED projector E-Manual

Audio output jack port The audio output jack port allows you to connect your LED projector to amplified speakers or headphones.

HDMI port This port is for the HDMI (High-Definition Multimedia Interface) connectors. This port is HDCP compliant for HD DVD, Blu-ray, and other protected content playback.

USB Type-A power output port This power output port provides up to 5V/1A of output voltage and current. You can connect your mobile device to this port to keep it charged while using it with your LED projector.

Rear view

LED projector E-Manual 15

USB 3.1 Gen 2 Type-C DisplayPort/Power Delivery combo port Use a USB Type-C adapter to connect your LED projector to a compatible device to stream media contents. This Power Delivery output port provides up to 5V/1.5A of output voltage and current when a power source is connected to the Power (DC) input port. You can connect your mobile device to this port to keep it charged while using it with your LED projector.

NOTE: Ensure to use USB cables certified by the USB-IF to be compliant with USB 3.1 Gen 1 or above.

Manual reset hole If your LED projector is unresponsive, insert a straightened paper clip into this hole to turn off your LED projector, then press the power button to turn on your LED projector again.

Remote sensor The remote sensor detects signal from your LED projectors remote control, allowing you to access the LED projectors control panel from a distance of up to 8 meters and a receiving angle of 30 degrees.

Power button Press this power button to turn on or turn off your LED projector.

16 LED projector E-Manual

Power (DC) input port Insert the bundled power adapter into this port to charge the battery pack and supply power to your LED projector.

IMPORTANT! Use only the bundled power adapter to charge the battery pack and supply power to your LED projector.

WARNING! The adapter may become warm to hot while in use. DO NOT cover the adapter and keep it away from your body while it is connected to a power source.

Air vents The air vents allow cool air to enter and warm air to exit your LED projector.

WARNING! Ensure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating may occur.

Left side

LED projector E-Manual 17

Air vents The air vents allow cool air to enter and warm air to exit your LED projector.

WARNING! Ensure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating may occur.

Right side

18 LED projector E-Manual

Bottom view

Tripod socket Connect the LED projector to a tripod using this socket.

Built-in stand This LED projector comes with a built-in stand that allows you to adjust the height of the projector by either 4.5 degrees or 9.7 degrees.

LED projector E-Manual 19

Extended features Your LED projector also have stand-alone features that are launched by pressing the Back/Splendid button while your LED projector is on battery mode.

Flashlight

The LED projector flashes a steady white light when you use this feature.

Back/Splendid button

To use your LED projector as a flashlight:

1. Disconnect all peripherals from your LED projector then press the power button to turn it on.

2. Press on the control panel of your LED projector to launch

the NO SIGNAL display.

3. Press repeatedly until the LED projector flashes a steady

white light.

IMPORTANT! Ensure that your LED projector is charged and can run on battery mode before enabling this feature. Battery time varies depending on usage.

20 LED projector E-Manual

Emergency light mode

The LED projector flashes a blinking white light when you use this feature.

Back/Splendid button

To use your LED projector as a flashlight:

1. Disconnect all peripherals from your LED projector then press the power button to turn it on.

2. Press on the control panel of your LED projector to launch

the NO SIGNAL display.

3. Press repeatedly until the LED projector flashes a blinking

white light.

IMPORTANT! Ensure that your LED projector is charged and can run on battery mode before enabling this feature. Battery time varies depending on usage.

NOTE: To turn off or switch between the flashlight and emergency light feature of your LED projector, just press the Back/Splendid button until your preferred lighting feature is disabled or enabled.

LED projector E-Manual 21

LED projector remote control

NOTE: Actual appearance may vary depending on model.

Battery compartment The battery compartment allows you to use CR2025 lithium coin batteries to power your LED projectors remote control.

NOTE: For more details on using the battery compartment, refer to the Replacing the battery section in this manual.

22 LED projector E-Manual

Remote control buttons These additional buttons allow you to use the LED projector from a distance of up to 8 meters.

Power - Press this button to turn your LED projector on or off.

Auto focus - Press this button to automatically focus the image.

Back - Press this button to go back to the previous screen.

Keystone - Press this button to adjust the keystone of your projection onscreen.

Input - Press this button to change the input source.

Volume down - Press this button to decrease the volume.

Volume up - Press this button to increase the volume.

Focus up/Up - Press this button to increase the focus or move up.

Focus down/Down - Press this button to decrease the focus or move down.

Left - Press this button to move left.

Right - Press this button to move right.

Menu/OK - Press this button to launch the menu or confirm a menu selection.

NOTE: For more details on the onscreen display menu, refer to the Using the onscreen display menu section in this manual.

LED projector E-Manual 23

Replacing the battery

A. Move the battery compartments latch to the right to unlock the battery holder.

B. Pull down the battery holder and remove it completely out of the battery compartment.

C. Remove the old battery, then insert the new CR2025 lithium coin battery into the battery holder with the positive side (+) facing up.

24 LED projector E-Manual

D. Slide the battery holder back into the battery compartment. Push it all the way in until you hear a soft click, indicating that the battery compartment is locked back in place.

LED projector E-Manual 25

Chapter 2:

Setting up

Chapter 2: Setting up

26 LED projector E-Manual

Operating your LED projector This portable LED projector allows you to plug and play your devices so you can easily open multimedia files and hear audio straight from its built-in SonicMaster speakers.

For your safety and to maintain the quality of this unit, refer to the following steps when operating your LED projector.

Connect the LED projector to the power adapter

A. Connect the AC/DC power cord to the power adapter.

B. Connect the AC power cord to a power source.

C. Connect the DC power connector to your LED projector.

Power adapter information: - Input voltage: 100-240Vac - Input frequency: 50-60Hz - Rating output current: 3.42A max. (65W) - Rating output voltage: 19V

LED projector E-Manual 27

IMPORTANT!

Useonlythebundledpoweradaptertochargethebatterypack and supply power to your LED projector.

EnsurethatyourLEDprojectorisconnectedtothepoweradapter before turning it on for the first time. We strongly recommend that you use a grounded wall socket while using your LED projector on power adapter mode.

ThesocketoutletmustbeeasilyaccessibleandnearyourLED projector.

TodisconnectyourLEDprojectorfromitsmainpowersupply, unplug your LED projector from the power socket.

WARNING!

Read the following precautions for your LED projectors battery.

Thebatteryusedinthisdevicemaypresentariskoffireor chemical burn if removed or disassembled.

Followthewarninglabelsforyourpersonalsafety.

Riskofexplosionifbatteryisreplacedbyanincorrecttype.

Donotdisposeofinfire.

Neverattempttoshort-circuityourLEDprojectorsbattery.

Neverattempttodisassembleandreassemblethebattery.

Discontinueusageifleakageisfound.

Thebatteryanditscomponentsmustberecycledordisposedof properly.

Keepthebatteryandothersmallcomponentsawayfrom children.

28 LED projector E-Manual

AC power cord requirements

Use the correct AC plug type according to your current location.

IMPORTANT! Contact your sales dealer if the AC power cord bundled with your LED projector does not match your local power source.

NOTE: We highly recommend that you use a video source device that also uses a grounding type plug to prevent signal interference due to voltage fluctuations.

For Australia and Mainland China For U.S.A., Canada, and Taiwan

For Continental Europe For U.K.

LED projector E-Manual 29

Connect the LED projector to your device

A. Audio output jack

30 LED projector E-Manual

B. HDMI input

LED projector E-Manual 31

C. Power output (5V/1A)

NOTE: The power output port is available when using the LED projector in battery mode or charging mode.

32 LED projector E-Manual

D. USB 3.1 Gen 2 Type-C DisplayPort input

LED projector E-Manual 33

E. USB 3.1 Gen 2 Type-C Power Delivery output (5V/1.5A)

NOTE: The Power Delivery output port is only available when using the LED projector in charging mode.

34 LED projector E-Manual

Adjust the height of the LED projector Your LED projector comes with a built-in stand that helps adjust the image height onscreen.

WARNING! Ensure that the built-in stand is fully retracted before placing the LED projector inside the projector bag.

NOTE:

Place the LED projector on a stable flat surface.

Keepaspaceof30cmormorebetweenthesidesoftheLED projector.

Consultyourdealerforspecialinstallationprocedureslike suspending the LED projector from the ceiling.

4.5o

9.7o

LED projector E-Manual 35

Projection distance

LED projector

Screen size

Screen size and projection distance table

Adjust the LED projectors distance from the screen using the table below.

Screen Size Projection DistanceScreen

Diagonal Horizontal Vertical

inch mm inch mm inch mm inch mm

60 1524 52.28 1328 29.41 747 59.06 1500

70 1778 61.02 1550 34.33 872 68.90 1750

80 2032 69.72 1771 39.21 996 78.74 2000

90 2286 78.43 1992 44.13 1121 88.58 2250

100 2540 87.17 2214 49.02 1245 98.43 2500

110 2794 95.87 2435 53.94 1370 108.27 2750

120 3048 104.61 2657 58.82 1494 118.11 3000

36 LED projector E-Manual

Press the power button

3s

LED projector E-Manual 37

Adjust the image focus Push the focus button on the LED projector up or down, or press the focus button on the remote control to adjust the image focus.

NOTE: Use a still image when adjusting the onscreen display.

OR

38 LED projector E-Manual

LED projector E-Manual 39

Chapter 3: Using the onscreen display menu

Chapter 3:

Using the onscreen display menu

40 LED projector E-Manual

NOTE: The following screenshots are for reference only and may be updated without prior notice. Screenshots may also vary depending on the LED projector model.

Using your LED projector for the first time Refer to the following steps when using your LED projector for the first time.

NOTE: Ensure that your LED projector is connected to the power adapter before turning it on for the first time. We strongly recommend that you use a grounded wall socket while using your LED projector on power adapter mode.

1. Set up your LED projector then press the power button.

2. Move the joystick left or right on your LED projector (or press the Left or Right button on your remote control) to browse through the available language options.

3. After you have chosen your preferred language, press the center of the joystick (or press the Menu/OK button on your remote control) to set this language for use on your LED projector.

4. You may now start using your LED projector to display files from your input device. The NO SIGNAL screen may appear if no input device is connected or cannot be detected by the LED projector.

LED projector E-Manual 41

Joystick

Adjusting your LED projector's settings To adjust your LED projector settings:

1. Press the center of the joystick on your LED projector (or press the Menu/OK button on your remote control) to launch the onscreen display menu.

2. Move the joystick up or down (or press the Focus up/Up or Focus down/Down button on your remote control) to select the menu option you would like to adjust.

3. Press the center of the joystick (or press the Menu/OK button on your remote control) to open the selected option's settings.

4. Move the joystick left or right (or press the Left or Right button on your remote control) to adjust the settings according to your preference.

5. When finished, press the center of the joystick or press the Menu/OK button on your remote control) to save the new settings and go back to the home screen.

Remote control buttons

42 LED projector E-Manual

Onscreen display menu options Image The options under this menu allows you to adjust image options to fine tune your image projection onscreen.

Splendid - This option allows you to select a Splendid mode for your LED projector.

Brightness - Select this menu option to adjust the brightness of your projection onscreen.

Contrast - Select this menu option to adjust the contrast of your projection onscreen.

Saturation - Select this menu option to adjust the saturation of your projection onscreen.

Sharpness - Select this menu option to adjust the sharpness of your projection onscreen.

Tint - Select this menu option to adjust the tint of your projection onscreen.

Wall Color - This option allows you to choose a proper color according to the wall.

Gamma - Select this menu option to adjust the gamma of your projection onscreen.

LED projector E-Manual 43

Auto Focus - This option allows you to turn Auto Focus on or off.

Projection Position - This option allows you to change the way your projections are oriented onscreen based from the current location of your LED projector.

Auto Ceiling Detection - This option allows you to turn Auto Ceiling detection on or off.

Keystone - Select this menu option to adjust the keystone of your projection onscreen.

Quick Corner - Select this menu option to adjust the corners of your projection onscreen.

Aspect Ratio - Select this menu option to adjust the screen ratio of your projection onscreen.

Digital Zoom - This option allows you to zoom in, zoom out, and pan your projection onscreen.

Display The options under this menu allows you to adjust how the image projection will be displayed.

44 LED projector E-Manual

Input The options under this menu allows you to select the input source for your LED projector.

Auto Source - This option allows you to turn Auto Source on or off. Turn this option on to scan the connected devices to your LED projector automatically.

HDMI - Select this menu option to project images from the HDMI port.

USB-A - Select this menu option to charge your mobile device connected to the USB Type-A power output port.

USB-C - Select this menu option to project images from the USB 3.1 Gen 2 Type-C DisplayPort/Power Delivery combo port.

Wireless Mirroring - Select this menu option to wirelessly project images from a supported Android or Windows 10 device.

LED projector E-Manual 45

OSD Timeout - This option allows you to set the number of seconds before the onscreen display menu disappears from your projection screen.

Sound - This option allows you to adjust the projector sound settings.

Power Off Timeout - This option allows you to set the number of minutes before your LED projector automatically shuts down when not in use.

Language - This option allows you to select the language to use on your LED projectors onscreen display menu.

Information - Select this menu option to see an overview of information about your LED projector.

Reset all - This option allows you to reset all the settings you have currently set up for your LED projector.

System Update - This option allows you to update the LED projectors firmware.

NOTE: For the latest firmware and more information, visit https://www.asus.com/Projectors/ASUS-ZenBeam-S2/

System The options under this menu allows you to configure system settings for your LED projector.

46 LED projector E-Manual

Turning off your LED projector 1. Press the power button.

2. When the following screen appears, press the power button again to completely turn off your LED projector.

LED projector E-Manual 47

Multi-language versions Download other language versions of this E-Manual via this website: https://www.asus.com/support

48 LED projector E-Manual

LED projector E-Manual 49

Appendices

AppendicesAppendices

50 LED projector E-Manual

Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorientorrelocatethereceivingantenna.

Increasethedistancebetweentheequipmentandreceiver.

Connecttheequipmenttoanoutletonadifferentcircuitthan that which the receiver is connected to.

Consultthedealeroranexperiencedradio/TVtechnicianfor help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference that may cause undesired operation.

LED projector E-Manual 51

Regional notice for California

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

Dclaration de conformit de Innovation, Sciences et Dveloppement conomique Canada (ISED) Le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

CAN ICES-3(B)/NMB-3(B)

52 LED projector E-Manual

Global Environmental Regulation Compliance and Declaration ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements.

Please refer to http://csr.asus.com/english/Compliance.htm for information disclosure based on regulation requirements ASUS is complied with:

Japan JIS-C-0950 Material Declarations

EU REACH SVHC

Korea RoHS

ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

LED projector E-Manual 53

S2 Display Display Technology 0.3 DLP

Light Source R/G/B LED

Light Source Life 30,000 hours (Max)

True Resolution (native)

HD 720p (1280 x 720)

Light Output (Max) 500 Lumens

Contrast Ratio 400:1 (typical) 4,000:1 (DCR)

Color Saturation (NTSC)

24:00:00

Display Colors 16.7 Million Colors

Projection Lens

Throw Ratio 1.12:1 (40 @ 1m) (@16:9 )

Projection Distance / Size

1.5m ~ 3m

Projection Offset 60 ~ 120

Zoom Ratio Fixed

Focus Power Focus

Video Features

Picture Modes 4 modes (Presentation / Standard / Theater / Eco)

Additional Modes 2 modes ( Flash light / SOS)

Keystone adjustment 2D(H/V) keystone correction

Auto Keystone Yes (Vertical)

Aspect Ratio 16:9 / 16:10 / 4:3

Projector Placement Front Table, Rear Table, Rear ceiling, Front ceiling

Audio Features

Built-in speakers Yes, 2W speaker (ASUS SonicMaster Audio technology)

(continued on the next page)

Specifications for S2 series LED projector

54 LED projector E-Manual

S2 Signal Frequency

Digital Signal Frequency

37.8 ~ 79.9 KHz(H) / 50 ~ 60 Hz(V)

Power Power On Mode 65 W

Standby Mode <0.5 W

Noise Standard mode 32dB

Interface Signal Input USB-C (DP Alt Mode), HDMI

Audio Output Earphone out (3.5mm Mini- jack)

USB Port Type-A 2.0 x 1 (5V/1A Power output)

Wireless Projection Yes (Android, Windows 10)

Mechanical Design

Chassis Colors Navy Blue / Ceramic White

Tripod Socket Yes

Stand (Two steps)

Ceiling Monut Yes

Dimension Physical Dimension 120(W)x120(D)x35(H)mm

Box Dimension 224(W)x190(D)x142(H)mm

Weight Net Weight (Esti.) 497g

Gross Weight (Esti.) 1500g

Operating Temperature 0 ~ 40o C

Operating Humidity 20 ~ 90%

Accessories Carrying bag, HDMI Cable, Adapter, Power Cord, Remote Control, QSG, Warranty Card

* Specifications are subject to change without prior notice. ** Product availability may vary by region. *** All brand and product names mentioned are trademarks of their

respective companies.

LED projector E-Manual 55

Support PC Timings

HDMI (Video) Timing Resolution Vertical frequency (Hz) H-frequency

(kHz) Dot Clock

frequency (MHz) 720/50p 1280 x 720 50 37.5 74.25 720/60p 1280 x 720 60 45 74.25 1080/50P 1920 x 1080 50 56.25 148.5 1080/60P 1920 x 1080 60 67.5 148.5 1080/24P 1920 x 1080 24

HDMI (PC) Resolution Mode Refresh rate (Hz) H-frequency (kHz) Clock (MHz)

800 x 600 SVGA_60 60.317 37.879 40 SVGA_75 75 46.875 49.5

1024 x 768 XGA_60 60.004 48.363 65 XGA_75 75.029 60.023 78.75

1280 x 768 1280 x 768_60 59.87 47.776 79.5 1280 x 800 WXGA_60 59.81 49.702 83.5 1280 x 1024 SXGA_60 60.02 63.981 108

SXGA_75 75.025 79.976 135 1280 x 960 1280 x 960_60 60 60 108 1440 x 900 WXGA+_60 59.887 55.935 106.5 1400X1050 SXGA+_60 59.978 65.317 121.75 1024x768@75Hz MAC19 74.93 60.241 80 1366x768 HD_60 59.79 47.71 85.50 1680x1050 W