Contents

ASUS F1 Projector User Manual PDF

1 of 58
1 of 58

Summary of Content for ASUS F1 Projector User Manual PDF

TH R

RO

OHS1: 8

W EN

.

S

0

LED projector E-Manual

F1 Series

2 LED projector E-Manual

COPYRIGHT AND WARRANTY INFORMATION

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (ASUS).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the is defaced or missing.

ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Copyright 2019 ASUSTeK COMPUTER INC. All Rights Reserved.

LIMITATION OF LIABILITY

Circumstances may arise where because of a default on ASUS part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the listed contract price of each product.

ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement.

This limit also applies to ASUS suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.

UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.

SERVICE AND SUPPORT

Visit our multi-language web site at https://www.asus.com/support

E14384 First Edition March 2019

LED projector E-Manual 3

Table of Contents About this manual ............................................................................................. 5

Conventions used in this manual ............................................................... 6 Typography ......................................................................................................... 6 Multi-language versions ................................................................................ 6

Safety precautions ............................................................................................. 7 Using your LED projector ............................................................................... 7 Servicing and replacement of parts .......................................................... 7 Caring for your LED projector ...................................................................... 8 Proper disposal .................................................................................................. 8

Chapter 1: Knowing your LED projector Features ...............................................................................................................10

Top view .............................................................................................................10 Front view ..........................................................................................................12 Rear view ...........................................................................................................13 Left side .............................................................................................................14 Right side ...........................................................................................................15 Bottom view .....................................................................................................16

Mounting your LED projector ......................................................................17 Projecting files from a mounted position ..............................................18 Ceiling mount hole details ..........................................................................18

LED projector remote control ......................................................................19 Replacing the battery ...................................................................................21 Remote control effective range .................................................................23

Chapter 2: Setting up Operating your LED projector .....................................................................26

Connect the LED projector to the power adapter ..............................26 Connect the LED projector to your device ............................................28 Adjust the height of the LED projector ...................................................32 Press the power button ................................................................................34 Adjust the image focus .................................................................................35

4 LED projector E-Manual

Chapter 3: Using the onscreen display menu Using your LED projector for the first time .............................................38 Adjusting your LED projector's settings ..................................................39 Onscreen display menu options .................................................................40

Image .............................................................................................................40 Display .............................................................................................................41 Input .............................................................................................................42 System .............................................................................................................43

Turning off your LED projector ....................................................................45 Using 3D glasses ...............................................................................................46

Multi-language versions ..............................................................................47

Appendices Federal Communications Commission Statement .............................50 Regional notice for California .....................................................................51 Global Environmental Regulation Compliance and Declaration .52 ASUS Recycling/Takeback Services ..........................................................52 Specifications for F1 series LED projector ..............................................53 Supported PC Timings ..................................................................................56

LED projector E-Manual 5

About this manual This manual provides information about the hardware and software features of your LED projector through the following chapters:

Chapter 1: Knowing your LED Projector

This chapter details the parts of your LED projector and its accompanying remote control.

Chapter 2: Setting up

This chapter shows you how to set up your LED projector and use its parts for input device connection.

Chapter 3: Using the onscreen display menu

This chapter talks about the features of your LED projectors onscreen display menu and how to navigate it using the control panel.

Appendices

This section includes safety notices for your LED projector.

6 LED projector E-Manual

Conventions used in this manual To highlight key information in this manual, some text are presented as follows:

IMPORTANT! This message contains vital information that must be followed to complete a task.

NOTE: This message contains additional information and tips that can help complete tasks.

WARNING! This message contains important information that must be followed to keep you safe while performing tasks and prevent damage to your LED projector's data and components.

Typography Bold = This indicates a menu or an item that must be selected.

Italic = This indicates sections that you can refer to in this manual.

Multi-language versions Download other language versions of this E-Manual via this website: https://www.asus.com/support

LED projector E-Manual 7

Safety precautions Using your LED projector

Refertothemanualandtakenoteofthesafetyinstructions before operating your LED projector.

Followthenotesandwarningsstatedintheusermanual.

DonotplaceyourLEDprojectoronunevenorunstablesurfaces.

DonotuseyourLEDprojectorinsmokyenvironments.Smoke residue may cause build-up on critical parts and damage the LED projector or decrease its performance.

KeeptheLEDprojectorsplasticpackagesoutofthereachof children.

DonotblockorplaceanythingneartheLEDprojectors ventilation holes. Doing so may cause internal heat build-up that can degrade picture quality and damage the projector.

EnsurethattheoperatingvoltageofyourLEDprojector matches the voltage of your power source.

Servicing and replacement of parts

DonotdisassembleorattempttoservicethisLEDprojectorby yourself. Contact your local ASUS service center for assistance.

WhenreplacingpartsofyourLEDprojector,purchaseitems as specified by ASUS and contact your local service center for assistance.

8 LED projector E-Manual

Caring for your LED projector

SwitchoffthenunplugtheLEDprojectorfromthepoweroutlet before cleaning it.

WhencleaningtheLEDprojectorshousing,useacleansoft cloth dampened with water or a mix of water and neutral detergent. Wipe it dry using a soft dry cloth.

Ensurethatthelensiscoolbeforecleaningit.Gentlywipethe lens using a lens cleaning paper. Do not touch the lens with your hands.

Donotuseliquidoraerosolcleaners,benzene,orthinnerson your LED projector.

NeveroperatethisLEDprojectorimmediatelyaftermovingit from a cold location. When the LED projector is exposed to a drastic change in temperature, moisture may condense on the lens and its other internal parts. To prevent this, use the unit two (2) hours after an extreme or sudden change in temperature occurs.

Proper disposal

Do not throw your LED projector in municipal waste. This product has been designed to enable proper reuse of parts and recycling. The symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment and mercury-containing button cell battery) should not be placed in municipal waste. Check local regulations for disposal of electronic products.

Do not throw the battery in municipal waste. The symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

LED projector E-Manual 9

Chapter 1: Knowing your LED projector

Chapter 1:

Knowing your LED projector

10 LED projector E-Manual

Features

Top view

LED projector E-Manual 11

Control panel buttons These buttons correspond to a specific LED projector setting as indicated below.

Keystone Input Power

NOTE: In the event that your LED projector becomes unresponsive, unplug the power cord and wait until your LED projector shuts down.

Joystick This joystick allows you to navigate the onscreen display menu and select menu settings. This joystick also correspond to specific LED projector settings as indicated below.

Open main menu / OK (push center)

Adjust focus (move up or down)

Adjust volume (move left or right)

NOTE: For more information on using your LED projectors settings, refer to the Using the onscreen display menu section in this manual.

12 LED projector E-Manual

Front view

TH R ROOHS1:8 W EN. S0

Lens cover The lens cover protects the lens from scratches and possible dirt build-up.

IMPORTANT! Remove the lens cover before using your LED projector.

Lens The lens projects video or image files onscreen from your input device.

WARNING! Do not touch the lens using your hands or any sharp object.

Auto focus camera This camera helps the LED projector with the auto focus feature.

LED projector E-Manual 13

Power (DC) input port Insert the bundled power adapter into this port to supply power to your LED projector.

WARNING! The adapter may become warm to hot while in use. Do not cover the adapter and keep it away from your body while it is connected to a power source.

IMPORTANT! Use only the bundled power adapter to supply power to your LED projector.

Remote sensor The remote sensor detects signal from your LED projectors remote control, allowing you to access the LED projectors control panel from a distance of up to 8 meters and a receiving angle of 30 degrees.

HDMI ports These ports are for the HDMI (High-Definition Multimedia Interface) connectors. These port are HDCP compliant for HD DVD, Blu-ray, and other protected content playback.

Rear view

14 LED projector E-Manual

Power output port This power output port provides up to 5V/2A of output voltage and current. You can connect your mobile device to this port to keep it charged.

VGA port This port allows you to connect your LED projector to other VGA-compatible devices.

Audio output jack port The audio output jack port allows you to connect your LED projector to amplified speakers or headphones.

Air vents The air vents allow cool air to enter and warm air to exit your LED projector.

WARNING! Ensure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating may occur.

Left side

LED projector E-Manual 15

Kensington security slot The Kensington security slot allows you to secure your LED projector using Kensington compatible LED projector security products.

Air vents The air vents allow cool air to enter and warm air to exit your LED projector.

WARNING! Ensure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating may occur.

Right side

16 LED projector E-Manual

Bottom view

Built-in stand This LED projector comes with a built-in stand that allows you to adjust the height of the projector by either 5.7 degrees or 8.2 degrees.

Ceiling mount holes Use these holes to connect the LED projector to a ceiling mount.

Tripod socket Connect the LED projector to a tripod using this socket.

LED projector E-Manual 17

Mounting your LED projector Aside from using the LED projector as a tabletop device, you can also mount it on the ceiling using the ceiling mount holes on its bottom side.

IMPORTANT! Ask a specialist or your retailer for assistance when mounting your LED projector to the ceiling. A qualified professional should do the installation process.

NOTE:

YoumayalsorefertotheScreensizeandprojectiondistancetable section in this manual to specify the right distance for mounting your LED projector on the ceiling.

Keepareasonablespacebetweenthebracketandtheprojector to allow for proper heat distribution.

Inadditiontotheceilingmountkitandscrews,wealso recommend using a metal bar or wire to hold the ceiling-mounted LED projector for added protection and to prevent it from falling due to natural causes such as earthquakes.

AURA RGB LED The AURA RGB LED provides several lighting schemes for you to customize your LED projector.

NOTE: For more details on customizing the AURA RGB LED, refer to the Using the onscreen display menu section in this manual.

18 LED projector E-Manual

Ceiling mount hole details

IMPORTANT! Ensure that the washers included in the ceiling mount kit are placed between the ceiling mount and screw to protect your LED projector and stabilize its position.

Projecting files from a mounted position After mounting your LED projector, you need to change its image position settings to ensure that files are automatically flipped and projected correctly onscreen.

To change your image position settings:

1. Navigate to Display > Projection Position on your LED projector.

2. Select Front Ceiling or Rear Ceiling to change the settings of your LED projector.

LED projector E-Manual 19

LED projector remote control

NOTE: Actual appearance may vary depending on model.

Battery compartment The battery compartment allows you to use CR2032 lithium coin batteries to power your LED projectors remote control.

NOTE: For more details on using the battery compartment, refer to the Replacing the battery section in this manual.

20 LED projector E-Manual

Remote control buttons These additional buttons allow you to use the LED projector from a distance of up to 8 meters.

Power - Press this button to turn your LED projector on or off.

Auto focus - Press this button to automatically focus the image.

/ Back/Splendid - Press this button to go back to the previous screen or select a Splendid mode for your LED projector.

Keystone - Press this button to adjust the keystone of your projection onscreen.

Input - Press this button to change the input source.

Volume down - Press this button to decrease the volume.

Volume up - Press this button to increase the volume.

Focus up/Up - Press this button to increase the focus or move up.

Focus down/Down - Press this button to decrease the focus or move down.

Left - Press this button to move left.

Right - Press this button to move right.

Menu/OK - Press this button to launch the menu or confirm a menu selection.

NOTE: For more details on the onscreen display menu, refer to the Using the onscreen display menu section in this manual.

LED projector E-Manual 21

Replacing the battery

A. Slide the battery cover down and remove it completely.

B. Remove the old batteries.

22 LED projector E-Manual

C. Insert the new CR2032 lithium coin batteries with the positive sides (+) facing up.

D. Slide the battery cover up all the way in until you hear a soft click, indicating that the battery cover is locked back in place.

LED projector E-Manual 23

Remote control effective range The remote sensor is located on the rear of your LED projector. The remote control must be held at an angle of 30 degrees perpendicular to the projectors remote control to function correctly. The distance between the remote control and the sensor should not exceed 8 meters (about 26 feet).

NOTE: Ensure sure that there are no obstacles between the remote control and the remote sensor on your LED projector.

30 degrees

24 LED projector E-Manual

LED projector E-Manual 25

Chapter 2:

Setting up

Chapter 2: Setting up

26 LED projector E-Manual

Operating your LED projector For your safety and to maintain the quality of this unit, refer to the following steps when operating your LED projector.

Connect the LED projector to the power adapter

A. Connect the AC/DC power cord to the power adapter.

B. Connect the AC power cord to a power source.

C. Connect the DC power connector to your LED projector.

Power adapter information: - Input voltage: 100-240Vac - Input frequency: 50-60Hz - Rating output current: 6.32A max. (120W) - Rating output voltage: 19V

LED projector E-Manual 27

AC power cord requirements

Use the correct AC plug type according to your current location.

IMPORTANT! Contact your sales dealer if the AC power cord bundled with your LED projector does not match your local power source.

NOTE: We highly recommend that you use a video source device that also uses a grounding type plug to prevent signal interference due to voltage fluctuations.

For Australia and Mainland China For U.S.A., Canada, and Taiwan

For Continental Europe For U.K.

28 LED projector E-Manual

Connect the LED projector to your device

A. Audio output jack

LED projector E-Manual 29

B. HDMI

30 LED projector E-Manual

C. Power output (5V/2A)

LED projector E-Manual 31

D. VGA

32 LED projector E-Manual

Adjust the height of the LED projector Your LED projector comes with a built-in stand that helps adjust the image height onscreen.

WARNING! Ensure that the built-in stand is fully retracted before placing the LED projector inside the projector bag.

NOTES:

Place the LED projector on a stable flat surface.

Keepaspaceof30cmormorebetweenthesidesoftheLED projector.

Consultyourdealerforspecialinstallationprocedureslike suspending the LED projector from the ceiling.

LED projector E-Manual 33

Projection distance

LED projector

Screen size

Screen size and projection distance table

Adjust the LED projectors distance from the screen using the table below.

Screen Size Projection DistanceScreen

Diagonal Width Height

inch cm inch cm inch cm ft m

25 63.5 21.79 55.35 12.26 31.13 1.41 0.45

56.5 143.51 49.24 125.08 27.70 70.36 3.28 1.00

65 165.1 56.65 143.9 31.87 80.94 3.773 1.15

80 203.2 69.73 177.11 39.22 99.62 4.66 1.42

100" 254 87.16 221.38 49.03 124.53 5.81 1.77

160" 406.4 135.68 344.63 84.80 215.4 9.28 2.83

210" 533.4 178.08 452.32 111.30 282.7 12.14 3.70

34 LED projector E-Manual

Press the power button

LED projector E-Manual 35

Adjust the image focus Push the focus button on the LED projector up or down, or press the focus button on the remote control to adjust the image focus.

NOTE: Use a still image when adjusting the onscreen display.

OR

36 LED projector E-Manual

LED projector E-Manual 37

Chapter 3: Using the onscreen display menu

Chapter 3:

Using the onscreen display menu

38 LED projector E-Manual

NOTE: The following screenshots are for reference only and may be updated without prior notice. Screenshots may also vary depending on the LED projector model.

Using your LED projector for the first time Refer to the following steps when using your LED projector for the first time.

NOTE: Ensure that your LED projector is connected to the power adapter before turning it on for the first time. We strongly recommend that you use a grounded wall socket while using your LED projector on power adapter mode.

1. Set up your LED projector then press the power button.

2. Move the joystick left or right on your LED projector to browse through the available language options.

3. After you have chosen your preferred language, press the center of the joystick to set this language for use on your LED projector.

4. You may now start using your LED projector to display files from your input device. The NO SIGNAL screen may appear if no input device is connected or cannot be detected by the LED projector.

LED projector E-Manual 39

Joystick

Adjusting your LED projector's settings To adjust your LED projector settings:

1. Press the center of the joystick on your LED projector (or press the Menu/OK button on your remote control) to launch the onscreen display menu.

2. Move the joystick up or down (or press the Focus up/Up or Focus down/Down button on your remote control) to select the menu option you would like to adjust.

3. Press the center of the joystick (or press the Menu/OK button on your remote control) to open the selected option's settings.

4. Move the joystick left or right (or press the Left or Right button on your remote control) to adjust the settings according to your preference.

5. When finished, press the center of the joystick or press the Menu/OK button on your remote control) to save the new settings and go back to the home screen.

Remote control buttons

40 LED projector E-Manual

Onscreen display menu options Image The options under this menu allows you to adjust image options to fine tune your image projection onscreen.

Brightness - Select this menu option to adjust the brightness of your projection onscreen.

Contrast - Select this menu option to adjust the contrast of your projection onscreen.

Saturation - Select this menu option to adjust the saturation of your projection onscreen.

Sharpness - Select this menu option to adjust the sharpness of your projection onscreen.

Tint - Select this menu option to adjust the tint of your projection onscreen.

Splendid - This option allows you to select a Splendid mode for your LED projector.

Color Temperature - This option allows you to adjust the color temperature of your LED projector.

LED projector E-Manual 41

Wall Color - This option allows you to choose a proper color according to the wall.

Gamma - Select this menu option to adjust the gamma of your projection onscreen.

Auto Focus - This option allows you to turn Auto Focus on or off.

Projection Position - This option allows you to change the way your projections are oriented onscreen based from the current location of your LED projector.

Auto Ceiling Rotation - This option allows you to turn Auto Ceiling detection on or off.

Keystone - Select this menu option to adjust the keystone of your projection onscreen.

Aspect Ratio - Select this menu option to adjust the screen ratio of your projection onscreen.

Display The options under this menu allows you to adjust how the image projection will be displayed.

42 LED projector E-Manual

Digital Zoom - This option allows you to zoom in, zoom out, and pan your projection onscreen.

3D - Select this menu option to adjust 3D settings of your projection onscreen.

Input The options under this menu allows you to select the input source for your LED projector.

Auto Source - This option allows you to turn Auto Source on or off. Turn this option on to scan the connected devices to your LED projector automatically.

VGA/PC - Select this menu option to project images from the VGA port.

HDMI 1 - Select this menu option to project images from the HDMI 1 port.

HDMI 2 - Select this menu option to project images from the HDMI 2 port.

Wireless Mirroring - Select this menu option to wirelessly project images from a supported Android or Windows 10 device.

LED projector E-Manual 43

OSD Timeout - This option allows you to set the number of seconds before the onscreen display menu disappears from your projection screen.

Sound - This option allows you to adjust the projector sound settings.

Auto Power On - This option allows the LED projector to automatically turn on when it is connected to a power source.

Power Off Timeout - This option allows you to set the number of minutes before your LED projector automatically shuts down when not in use.

AURA RGB - Select this menu option to adjust the AURA RGB LED of your projector.

Language - This option allows you to select the language to use on your LED projectors onscreen display menu.

System The options under this menu allows you to configure system settings for your LED projector.

44 LED projector E-Manual

Information - Select this menu option to see an overview of information about your LED projector.

Reset all - This option allows you to reset all the settings you have currently set up for your LED projector.

NOTE: Please wait for at least eight (8) seconds for the reset process to complete, then reselect a language.

LED projector E-Manual 45

Turning off your LED projector 1. Press the power button.

2. When the following screen appears, press the power button again to completely turn off your LED projector.

46 LED projector E-Manual

Using 3D glasses Your LED projector supports 3D technology for an enhanced viewing experience.

IMPORTANT! Purchase DLP Link 3D glasses. Your 3D files must be compatible with the 3D format.

NOTE: For more details on viewing 3D files, refer to the user guide that comes with your 3D glasses.

To view 3D files:

1. Play your 3D file, then navigate to Display > 3D on your LED projector.

NOTE: The 3D mode is set to Off by default.

2. Select Auto to allow your LED projector to automatically select a 3D mode best suited for your 3D file.

NOTE: Select a 3D modemanually if your LED projector cannot detect which 3D mode to use.

IMPORTANT! Set the 3D mode back to Off to exit 3D mode.

LED projector E-Manual 47

Multi-language versions Download other language versions of this E-Manual via this website: https://www.asus.com/support

48 LED projector E-Manual

LED projector E-Manual 49

Appendices

AppendicesAppendices

50 LED projector E-Manual

Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorientorrelocatethereceivingantenna.

Increasethedistancebetweentheequipmentandreceiver.

Connecttheequipmenttoanoutletonadifferentcircuitthan that which the receiver is connected to.

Consultthedealeroranexperiencedradio/TVtechnicianfor help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference that may cause undesired operation.

LED projector E-Manual 51

Regional notice for California

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

Dclaration de conformit de Innovation, Sciences et Dveloppement conomique Canada (ISED) Le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

CAN ICES-3(B)/NMB-3(B)

52 LED projector E-Manual

Global Environmental Regulation Compliance and Declaration ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements.

Please refer to http://csr.asus.com/english/Compliance.htm for information disclosure based on regulation requirements ASUS is complied with:

Japan JIS-C-0950 Material Declarations

EU REACH SVHC

Korea RoHS

ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

LED projector E-Manual 53

F1 Display Display Technology 0.47 DLP

Light Source R/G/B LED

Light Source Life 30,000 hours (Max)

True Resolution (native)

FHD 1920x1080

Light Output (Max) 1200 Lumens

Contrast Ratio 3500:1(DCR), 800:1 (Typical)

Color Saturation (NTSC)

100%

Display Colors 16.7 Million Colors

Projection Lens

Throw Ratio (@16:9) 0.8:1 (56.5 @ 1m)

Projection Distance 0.43 ~ 3.7 meters

Projection/Screen Size 25 ~ 210 inches

Projection Offset 105 5 %

Zoom Ratio Fixed

Video Features

Picture Modes 6 Modes (Standard Mode, Dynamic Mode, sRGB Mode, Scenery Mode, Theater Mode, Game Mode)

Keystone adjustment Vertical / Horizontal

Auto Keystone Yes (Vertical)

Aspect Ratio Auto /16:10 / 16:9 / 4:3

Projector Placement Front Table, Rear Table, Front Ceiling, Rear Ceiling

Audio Features

Built-in speakers 3W x 2 (Stereo) + 8W (Woofer) 2.1 Channel speaker with Harman Kardoncertified

(continued on the next page)

Specifications for F1 series LED projector

54 LED projector E-Manual

F1 Signal Frequency

Analog Signal Frequency

Horizontal: 15.37 ~ 91.14 KHz Vertical: 24 ~ 60 Hz

Digital Signal Frequency

Horizontal: 15.37 ~ 91.14 KHz Vertical: 24 ~ 120 Hz

Power Power On Mode <120W

Standby Mode <0.5W

Noise Acoustic Noise Standard mode: 32dB - 34dB Theater mode: 28dB - 30dB

Input or Output

PC Signal Input 1 x D-sub 2 x HDMI (HDCP support)

Audio Out Earphone out

USB port Yes (1 x Type A for 5V/2A charging)

Wireless Wi-Fi 802.11 a/b/g/n @ 2.4GHz and 5GHz

Mechanical Design

Chassis Colors Black

Tripod Socket Yes

Supporting Stand Yes (Two steps)

Ceiling Mount Yes

Lens Cover Yes

Security Kensington lock Yes

Dimension Physical Dimension 250(W) x 75(H) x 210(D) mm

Box Dimension 496(W) x 115(H) x 302(D) mm

(continued on the next page)

LED projector E-Manual 55

F1 Weight Net Weight (Esti.) 1.80 Kg

Gross Weight (Esti.) 3.80 Kg

Operating Temperature 0 ~ 40o C

Operating Humidity 20 ~ 90%

Accessories Carrying bag, power adapter, power cord, HDMI cable, Quick Start Guide, remote control, warranty card

* Specifications are subject to change without prior notice. ** Product availability may vary by region. *** All brand and product names mentioned are trademarks of their

respective companies.

56 LED projector E-Manual

Supported PC Timings VGA

Resolution Mode Refresh rate (Hz) H-frequency (kHz) 720 x 400 720 x 400_70 70.087 31.469

640 x 480 VGA_60 59.94 31.469 VGA_72 72.809 37.861 VGA_75 75 37.5

800 x 600 SVGA_60 60.317 37.879 SVGA_72 72.188 48.077 SVGA_75 75 46.875

1024 x 768 XGA_60 60.004 48.363 XGA_70 70.069 56.476 XGA_75 75.029 60.023

1152 x 864 1152 x 864_60 60

1280 x 720 1280 x 720_60 60 45 1280 x 720_120 120

1280 x 800 WXGA_60 59.81 49.702

1280 x 1024 SXGA_60 60.02 63.981 SXGA_75 75.025 79.976

1280 x 960 1280 x 960_60 60 60 1360 x 768 1360 x 768_60 60.015 47.712 1440 x 900 WXGA+_60 59.887 55.935 1600 x 1200 UXGA 60 75 1680 x 1050 1680 x 1050_60 59.95 62.29 640 x 480@67Hz MAC13 66.667 35 832 x 624@75Hz MAC16 74.546 49.722 1024 x 768@75Hz MAC19 74.93 60.241 1920 x 1080@60Hz 1920 x 1080_60 60 67.5

3D Video Format Timings (HDMI only)

Timing Frame Packing Side-by-side(Half) Top-and-Bottom 1280 x 720p @59.94/60 Hz v v v 1280 x 720p @50Hz v v v 1280 x 720p @23.98/24 Hz v 1280 x 720p @29.97/30 Hz v 1920 x 1080i @59.94/60Hz v v 1920 x 1080i @50Hz v v 1920 x 1080p @23.98/24 Hz v v v 1920 x 1080p @29.97/30 Hz v v 1920 x 1080p @59.94/60Hz v 1920 x 1080p @50Hz v

LED projector E-Manual 57

HDMI (Video) Timing Resolution Vertical frequency (Hz) H-frequency (kHz)

480i 720(1440) x 480 59.94 15.73 480p 720 x 480 59.94 31.47 576i 720(1440) x 576 50 15.63 576p 720 x 576 50 31.25 720/50p 1280 x 720 50 37.5 720/60p 1280 x 720 60 45 1080/50i 1920 x 1080 50 28.13 1080/60i 1920 x 1080 60 33.75 1080/50P 1920 x 1080 50 56.25 1080/60P 1920 x 1080 60 67.5 1080/24P 1920 x 1080 24

HDMI (PC) Resolution Mode Refresh rate (Hz) H-frequency (kHz)

720 x 400 720 x 400_70 70.087 31.469

640 x 480 VGA_60 59.94 31.469 VGA_72 72.809 37.861 VGA_75 75 37.5

800 x 600 SVGA_60 60.317 37.879 SVGA_72 72.188 48.077 SVGA_75 75 46.875

1024 x 768 XGA_60 60.004 48.363 XGA_70 70.069 56.476 XGA_75 75.029 60.023

1152 x 864 1152 x 864_60 60

1280 x 720 1280 x 720_60 60 45 1280 x 720_120 120

1280 x 800 WXGA_60 59.81 49.702

1280 x 1024 SXGA_60 60.02 63.981 SXGA_75 75.025 79.976

1280 x 960 1280 x 960_60 60 60 1360 x 768 1360 x 768_60 60.015 47.712 1440 x 900 WXGA+_60 59.887 55.935 1680 x 1050 1680 x 1050_60 59.95 62.29 640 x 480@67Hz MAC13 66.667 35 832 x 624@75Hz MAC16 74.546 49.722 1024 x 768@75Hz MAC19 74.93 60.241 1920 x 1080@60Hz 1920 x 1080_60 60 67.5

58 LED projector E-Manual

Simplified EU Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.com/support/

The WiFi operating in the band 51

Manualsnet FAQs

If you want to find out how the F1 ASUS works, you can view and download the ASUS F1 Projector User Manual on the Manualsnet website.

Yes, we have the User Manual for ASUS F1 as well as other ASUS manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a ASUS F1. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the ASUS F1 Projector User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This ASUS F1 Projector User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download ASUS F1 Projector User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print ASUS F1 Projector User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the ASUS F1 Projector User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.