Contents

ASUS A55-C Motherboard User Manual PDF

1 of 72
1 of 72

Summary of Content for ASUS A55-C Motherboard User Manual PDF

M ot

he rb

oa rd

A55-C

ii

E7917 First Edition January 2013

Copyright 2013 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (ASUS). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe.

Offer to Provide Source Code of Certain Software This product contains copyrighted software that is licensed under the General Public License (GPL), under the Lesser General Public License Version (LGPL) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product. Where the applicable license entitles you to the source code of such software and/or other additional data, you may obtain it for a period of three years after our last shipment of the product, either (1) for free by downloading it from http://support.asus.com/download or (2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location where you want to have it shipped to, by sending a request to:

ASUSTeK Computer Inc. Legal Compliance Dept. 15 Li Te Rd., Beitou, Taipei 112 Taiwan

In your request please provide the name, model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you. The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code. This offer is valid to anyone in receipt of this information. ASUSTeK is eager to duly provide complete source code as required under various Free Open Source Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address gpl@asus.com, stating the product and describing the problem (please DO NOT send large attachments such as source code archives, etc. to this email address).

iii

Contents Safety information ...................................................................................................... vi About this guide ........................................................................................................ vii A55-C specifications summary ................................................................................. ix Package contents ....................................................................................................... xi

Product introduction 1.1 Special features ............................................................................................1-1

1.1.1 Product highlights ...........................................................................1-1 1.1.2 ASUS Exclusive Features ............................................................... 1-1

1.2 Before you proceed ......................................................................................1-3 1.3 Motherboard overview .................................................................................1-4

1.3.1 Placement direction ........................................................................1-4 1.3.2 Screw holes ....................................................................................1-4 1.3.3 Motherboard layout .........................................................................1-5 1.3.4 Layout contents ...............................................................................1-6

1.4 Accelerated Processing Unit (APU) ............................................................ 1-6 1.4.1 APU installation ...............................................................................1-7 1.4.2 APU heatsink and fan assembly installation ................................... 1-8

1.5 System memory ..........................................................................................1-10 1.5.1 Overview .......................................................................................1-10 1.5.2 Memory configurations .................................................................. 1-10 1.5.3 Installing a DIMM ..........................................................................1-15

1.6 Expansion slots ..........................................................................................1-16 1.6.1 Installing an expansion card ......................................................... 1-16 1.6.2 Configuring an expansion card ..................................................... 1-16 1.6.3 PCI slots ........................................................................................1-16 1.6.4 PCI Express x1 slots .....................................................................1-16 1.6.5 PCI Express x16 slot .....................................................................1-16

1.7 Jumpers.......................................................................................................1-18 1.8 Connectors ..................................................................................................1-20

1.8.1 Rear panel ports ...........................................................................1-20 1.8.2 Internal connectors .......................................................................1-22

1.9 Software support ........................................................................................1-28 1.9.1 Installing an operating system ...................................................... 1-28 1.9.2 Support DVD information .............................................................. 1-28

iv

BIOS information 2.1 Managing and updating your BIOS ............................................................. 2-1

2.1.1 ASUS Update utility ........................................................................2-1 2.1.2 ASUS EZ Flash 2 ............................................................................2-2 2.1.3 ASUS CrashFree BIOS 3 utility ...................................................... 2-3 2.1.4 ASUS BIOS Updater .......................................................................2-4

2.2 BIOS setup program .....................................................................................2-6 2.3 Main menu ...................................................................................................2-10

2.3.1 System Language [English] .......................................................... 2-10 2.3.2 System Date [Day xx/xx/xxxx] ....................................................... 2-10 2.3.3 System Time [xx:xx:xx] ................................................................. 2-10 2.3.4 Security .........................................................................................2-10

2.4 Ai Tweaker menu ........................................................................................2-12 2.4.1 Ai Overclock Tuner [Auto] ............................................................. 2-12 2.4.2 Memory Frequency [Auto] ............................................................. 2-12 2.4.3 EPU Power Saving Mode [Disabled] ............................................ 2-12 2.4.4 DIGI+ VRM ....................................................................................2-13

2.5 Advanced menu ..........................................................................................2-14 2.5.1 CPU Configuration ........................................................................2-14 2.5.2 SATA Configuration .......................................................................2-15 2.5.3 USB Configuration ........................................................................2-16 2.5.4 NB Configuration ...........................................................................2-16 2.5.5 Onboard Devices Configuration .................................................... 2-17 2.5.6 APM ..............................................................................................2-18 2.5.7 Network Stack ...............................................................................2-19

2.6 Monitor menu ..............................................................................................2-20 2.6.1 CPU Temperature / MB Temperature [xxxC/xxxF]...................... 2-20 2.6.2 CPU / Chassis fan Speed [xxxx RPM] or [Ignore] / [N/A] .............. 2-20 2.6.3 CPU Q-Fan Control [Enabled] ...................................................... 2-20 2.6.4 CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage .................. 2-21

v

2.7 Boot menu ...................................................................................................2-22 2.7.1 Fast Boot [Enabled] ......................................................................2-23 2.7.2 Full Screen Logo [Enabled] ........................................................... 2-23 2.7.3 Post Delay Time [3 sec] ................................................................ 2-24 2.7.4 Bootup NumLock State [On] ......................................................... 2-24 2.7.5 Wait for F1 If Error [Enabled] ....................................................... 2-24 2.7.6 Option ROM Messages [Force BIOS] ........................................... 2-24 2.7.7 Interrupt 19 Capture [Postponed] .................................................. 2-24 2.7.8 Setup Mode [EZ Mode] ................................................................. 2-24 2.7.9 CSM (Compatibility Support Module) ............................................ 2-24 2.7.10 Secure Boot ..................................................................................2-25 2.7.11 Boot Option Priorities ....................................................................2-26 2.7.12 Boot Override ................................................................................2-26

2.8 Tools menu ..................................................................................................2-27 2.8.1 ASUS EZ Flash 2 Utility ................................................................ 2-27 2.8.2 ASUS SPD Information ................................................................. 2-27 2.8.3 ASUS O.C. Profile .........................................................................2-27

2.9 Exit menu ....................................................................................................2-28

Appendices Notices ..................................................................................................................... A-1 ASUS contact information ...................................................................................... A-3

vi

Safety information Electrical safety

To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device. Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged. Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit. Ensure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company. If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

Operation safety Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package. Before using the product, ensure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately. To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry. Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet. Place the product on a stable surface. If you encounter technical problems with the product, contact a qualified service technician or your retailer.

vii

About this guide This user guide contains the information you need when installing and configuring the motherboard.

How this guide is organized This guide contains the following parts: Chapter 1: Product introduction

This chapter describes the features of the motherboard and the new technology it supports.

Chapter 2: BIOS information This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.

Where to find more information Refer to the following sources for additional information and for product and software updates. 1. ASUS websites

The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.

2. Optional documentation Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.

viii

Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task.

CAUTION: Information to prevent damage to the components when trying to complete a task

IMPORTANT: Instructions that you MUST follow to complete a task. .

NOTE: Tips and additional information to help you complete a task.

Typography Bold text Indicates a menu or an item to select. Italics Used to emphasize a word or a phrase. Keys enclosed in the less-than and greater-than sign

means that you must press the enclosed key.

Example: means that you must press the Enter or Return key.

+ + If you must press two or more keys simultaneously, the key names are linked with a plus sign (+).

ix

(continued on the next page)

A55-C specifications summary

APU FM2 socket for AMD A-Series Accelerated Processor Unit (APU) with AMD Radeon HD 7000 Series graphics, up to 4 CPU cores

Supports AMD Turbo Core Technology 3.0 The AMD Turbo Core Technology 3.0 support depends on the APU types. Refer to www.asus.com for the AMD APU support list.

Chipset AMD A55 FCH

Memory 2 x 240-pin DIMM slots support a maximum 32GB unbuffered non-ECC DDR3 1866/1600/1333/1066 MHz memory modules

Dual-channel memory architecture The maximum 32GB memory capacity can be supported with 16GB or above

DIMMs. ASUS will update the memory QVL once the DIMMs are available in the market.

Refer to www.asus.com for the latest Memory QVL (Qualified Vendors List). When you install a total memory of 4GB capacity or more, Windows 32-bit

operating system may only recognize less than 3GB. We recommend a maximum of 3GB system memory if you are using a Windows 32-bit operating system.

Graphics Integrated AMD Radeon HD 7000 series graphics in Trinity APU VGA output support: D-Sub port

- Supports D-Sub with a maximum resolution of 1920x1600@60Hz - Supports Microsoft DirectX 11 - Maximum shared memory of 2GB - Supports AMD Dual Graphics technology

* Refer to www.amd.com for a list of discrete GPUs that support Dual Graphics.

Expansion slots 1 x PCIe 2.0 x16 slot 3 x PCIe 2.0 x1 slots 3 x PCI slots

Storage / RAID AMD A55 FCH: - 6 x Serial ATA 3.0Gb/s connectors with RAID 0, RAID 1, RAID 10 and

JBOD support

LAN Realtek 8111F PCIe Gigabit LAN controller

Audio Realtek ALC887 8-channel High Definition Audio CODEC

USB AMD A55 FCH: - 10 x USB 2.0/1.1 ports (6 ports at the rear panel, 4 ports at the front panel)

x

Specifications are subject to change without notice.

ASUS unique features

ASUS Exclusive Features - ASUS iCafe Memory Anti-theft - ASUS AI Suite II - AI Charger - ASUS UEFI BIOS

ASUS Quiet Thermal Solution - Stylish heatsink solution - ASUS Q-Fan

ASUS EZ DIY - ASUS CrashFree BIOS 3 - ASUS EZ Flash 2 - ASUS MyLogo 2

Special features 100% All high-quality conductive polymer

Back Panel I/O ports

1 x PS/2 mouse port 1 x PS/2 keyboard port 1 x D-Sub 1 x COM 1 x LAN (RJ-45) port 6 x USB 2.0 ports 3 x audio jacks

Internal I/O connectors / buttons / switches

2 x USB 2.0/1.1 connectors support additional 4 USB 2.0/1.1 ports 6 x SATA 3.0Gb/s connectors 1 x CPU fan connector 1 x Chassis fan connector 1 x Speaker connector 1 x High-definition front panel audio connector 1 x Chassis intrusion connector 1 x 10-pin System panel connector 1 x 24-pin EATX power connector 1 x 4-pin ATX 12V power connector

BIOS 64Mb Flash ROM, UEFI BIOS, PnP, DMI 2.0, WfM 2.0, ACPI 2.0a, SM BIOS 2.6

Support DVD Drivers ASUS Update ASUS utilities Anti-Virus software (OEM version)

Form Factor ATX form factor: 12.0 in x 8.1 in (30.5 cm x 20.6 cm)

A55-C specifications summary

xi

Package contents Check your motherboard package for the following items.

A55-C

PCIEX16

PCIEX1_3

PCIEX1_2

PCIEX1_1

PCI2

PCI1

PCI3

AAFP

CPU_FAN

CHA_FAN

BATTERYSuper I/O

AUDIO

ALC 887

EPU

KBMS

64Mb BIOS

CLRTCCHASSISSPEAKERUSBPW7~10

KBPWR

USBPW1~6

AMD

A55

RTL 8111F

D D

R 3

D IM

M _A

1 (6

4b it,

2 40

-p in

m od

ul e)

D D

R 3

D IM

M _B

1 (6

4b it,

2 40

-p in

m od

ul e)

LAN_USB12

USB56

USB34

SATA3G_2 SATA3G_4 SATA3G_6

SATA3G_1 SATA3G_3 SATA3G_5

S O

C K

E T

F M

2

ATX12V

E A

T X

P W

R

V G

A

C O

M

USB910 USB78 F_PANEL

ASUS A55-C motherboard 2 x Serial ATA 3.0 Gb/s cables

User Guide

1 x I/O Shield User Manual Support DVD

If any of the above items is damaged or missing, contact your retailer.

The illustrated items above are for reference only. Actual product specifications may vary with different models.

xii

1.1 Special features 1.1.1 Product highlights AMD A-series accelerated processors with AMD Radeon HD 7000 series graphics This motherboard supports AMD A-series accelerated processors with AMD Radeon HD 7000 series graphics. This revolutionary APU (Accelerated Processing Unit) combines processing power and advanced DirectX 11 graphics in one small, energy-efficient design that provides accelerated performance and an industry-leading visual experience. It features Dual-channel DDR3 memory support and data transfer rates up to 5GT/s.

AMD A55 FCH chipset AMD A55 FCH is designed to support up to 5GT/s interface speed and AMD CrossFireX multi-GPU technology. It also supports 6 x SATA 3.0Gb/s ports.

100% All High-quality Conductive Polymer Capacitors This motherboard uses all high-quality conductive polymer capacitors for durability, improved lifespan, and enhanced thermal capacity.

1.1.2 ASUS Exclusive Features ASUS UEFI BIOS (EZ Mode) ASUS UEFI BIOS, a UEFI compliant architecture, offers the first mouse-controlled intuitive graphical BIOS interface that goes beyond the traditional keyboard-only BIOS controls, providing you with more flexibility, convenience, and easier navigation than the traditional BIOS versions. It offers you dual selectable modes and native support for hard drives larger than 2.2 TB. ASUS UEFI BIOS includes the following new features:

F12 BIOS snapshot hotkey

F3 Shortcut for most accessed information

ASUS DRAM SPD (Serial Presence Detect) information for detecting faulty DIMMs, and helping with difficult POST situations.

Product introduction 1

ASUS A55-C 1-1

AI Suite II ASUS AI Suite II integrates several ASUS utilities and allows you to launch and operate these utilities simultaneously. It allows you to configure overclocking settings, adjust frequencies and related voltage settings, remotely control the system via a mobile device, and other tasks.

Ai Charger ASUS Ai Charger is ASUS fast-charging software that supports the Apple iPod, iPhone, and iPad.

Check your USB mobile device if it fully supports the BC 1.1 standard. The actual charging speed may vary with your USB device.

ASUS EZ Flash 2 ASUS EZ Flash 2 is a user-friendly utility that allows you to update the BIOS without using a bootable floppy disk or an OS-based utility.

ASUS MyLogo2 Turn your favorite photos into 256-color boot logos to personalize your system.

ASUS CrashFree BIOS 3 ASUS CrashFree BIOS 3 is an auto-recovery tool that allows you to restore a corrupted BIOS file using the bundled support DVD or a USB flash disk that contains the BIOS file.

Chapter 1: Product introduction1-2

1.2 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings.

Unplug the power cord from the wall socket before touching any component.

Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.

Hold components by the edges to avoid touching the ICs on them.

Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.

Before you install or remove any component, switch off the ATX power supply and detach its power cord. Failure to do so may cause severe damage to the motherboard, peripherals, or components.

ASUS A55-C 1-3

1.3 Motherboard overview 1.3.1 Placement direction When installing the motherboard, ensure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below.

DO NOT overtighten the screws! Doing so can damage the motherboard.

1.3.2 Screw holes Place six screws into the holes indicated by circles to secure the motherboard to the chassis.

A55-C

Place this side towards the rear of the chassis.

Chapter 1: Product introduction1-4

1.3.3 Motherboard layout

A55-C

PCIEX16

PCIEX1_3

PCIEX1_2

PCIEX1_1

PCI2

PCI1

PCI3

AAFP

CPU_FAN

CHA_FAN

BATTERYSuper I/O

AUDIO

ALC 887

EPU

KBMS

64Mb BIOS

CLRTCCHASSISSPEAKERUSBPW7~10

KBPWR

USBPW1~6

20.6cm(8.1in)

30 .5

cm (1

2. 0i

n)

AMD

A55

RTL 8111F

D D

R 3

D IM

M _A

1 (6

4b it,

2 40

-p in

m od

ul e)

D D

R 3

D IM

M _B

1 (6

4b it,

2 40

-p in

m od

ul e)

LAN_USB12

USB56

USB34

SATA3G_2 SATA3G_4 SATA3G_6

SATA3G_1 SATA3G_3 SATA3G_5

S O

C K

E T

F M

2

ATX12V

E A

T X

P W

R

V G

A

C O

M

USB910 USB78 F_PANEL

1 432 65 4

3

13 12 10 89112

7

ASUS A55-C 1-5

1.4 Accelerated Processing Unit (APU) This motherboard comes with an FM2 socket designed for AMD A-series accelerated processors with AMD Radeon HD 7000 series graphics.

Ensure that you use an APU designed for the FM2 socket. The APU fits in only one correct orientation. DO NOT force the APU into the socket to prevent bending the pins and damaging the APU!

1.3.4 Layout contents Connectors/Jumpers/Slots/LED Page 1. Keyboard power (3-pin KBPWR) 1-19 2. USB device wake-up (3-pin USBPW1~6, and 3-pin USBPW7~10) 1-19 3. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) 1-23 4. CPU and chassis fan connectors (4-pin CPU_FAN, and 3-pin CHA_FAN) 1-22 5. AMD FM2 socket 1-6 6. DDR3 DIMM slots 1-10 7. SATA 3.0Gb/s connectors (7-pin SATA3G_1~6) 1-24 8. Clear RTC RAM (3-pin CLRTC) 1-18 9. Chassis intrusion connector (4-pin CHASSIS) 1-26 10. Speaker connector (4-pin SPEAKER) 1-27 11. Front panel (10-pin F_PANEL) 1-25 12. USB 2.0 connectors (10-1 pin USB78, USB910) 1-27 13. Front panel audio connector (10-1 pin AAFP) 1-26

A55-C

A55-C CPU socket FM2

Chapter 1: Product introduction1-6

1.4.1 APU installation

1

43

2

ASUS A55-C 1-7

1 2

53 4

1.4.2 APU heatsink and fan assembly installation

Apply the Thermal Interface Material to the APU heatsink and APU before you install the heatsink and fan if necessary.

To install the APU heatsink and fan assembly

Chapter 1: Product introduction1-8

To uninstall the APU heatsink and fan assembly

5

3

1

4

2

ASUS A55-C 1-9

1.5 System memory 1.5.1 Overview This motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) sockets. A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched differently to prevent installation on a DDR2 DIMM socket. DDR3 modules are developed for better performance with less power consumption. The figure illustrates the location of the DDR3 DIMM sockets:

Channel Sockets Channel A DIMM_A1 Channel B DIMM_B1

1.5.2 Memory configurations You may install 1GB, 2GB, 4GB, 8GB, and 16GB unbuffered non-ECC DDR3 DIMMs into the DIMM sockets.

You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.

We recommend that you install the memory modules on the blue slots for better overclocking capability.

Always install DIMMs with the same CAS latency. For optimal compatibility, we recommend that you install memory modules of the same version or date code (D/C) from the same vendor. Check with the retailer to get the correct memory modules.

Due to the memory address limitation on 32-bit Windows OS, when you install 4GB or more memory on the motherboard, the actual usable memory for the OS can be about 3GB or less. For effective use of memory, we recommend that you do any of the following:

- Install a maximum of 3GB system memory if you are using a 32-bit Windows OS.

- Use a 64-bit Windows OS if you want to install 4GB or more memory on the motherboard.

This motherboard does not support DIMMs made up of 512Mb (64MB) chips or less.

The maximum 32GB memory capacity can be supported with 16GB or above DIMMs. ASUS will update the memory QVL once the DIMMs are available in the market.

A55-C

A55-C 240-pin DDR3 DIMM sockets

D IM

M _A

1 D

IM M

_B 1

Chapter 1: Product introduction1-10

The default memory operation frequency is dependent on its Serial Presence Detect (SPD), which is the standard way of accessing information from a memory module. Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value. To operate at the vendor-marked or at a higher frequency, refer to section 2.4 Ai Tweaker menu for manual memory frequency adjustment.

For system stability, use a more efficient memory cooling system to support a full memory load (2 DIMMs) or overclocking condition.

Vendors Part No. Size SS/ DS

Chip Brand

Chip No. Timing Voltage

DIMM socket support (optional) 1DIMM 2DIMMs

CORSAIR CMT4GX3M2A1866C9(XMP) 4GB(2 x 2GB) DS - - 9-9-9-24 1.65V . . CORSAIR CMT6GX3MA1866C9(XMP) 6GB(3 x 2GB) DS - - 9-9-9-24 1.65V . . CORSAIR CMZ8GX3M2A1866C9(XMP) 8GB(2 x 4GB) DS - - 9-10-9-27 1.50V . . G.SKILL F3-14900CL9Q-16GBZL(XMP1.3) 16GB ( 4GB x4 ) DS - - 9-10-9-28 1.5V . . G.SKILL F3-14900CL10Q2-64GBZLD(XMP1.3) 64GB ( 8GBx 8 ) DS - - 10-11-10-30 1.5V . . G.SKILL F3-14900CL9D-8GBXL(XMP) 8GB(2 x 4GB) DS - - 9-10-9-28 1.5V . . G.SKILL F3-14900CL9Q-8GBXL(XMP) 8GB(2GBx4) DS - - 9-9-9-24 1.6V . . KINGSTON KHX1866C9D3K4/16GX(XMP) 16GB ( 4GB x4 ) DS - - - 1.65V . . KINGSTON KHX1866C9D3T1K3/6GX(XMP) 6GB(3 x 2GB) DS - - - 1.65V . . KINGSTON KHX1866C11D3P1K2/8G 8GB ( 4GB x 2) DS - - - 1.5V . . KINGSTON KHX1866C9D3K2/8GX(XMP) 8GB(4GBX2) DS - - - 1.65V . .

DDR3-1866 MHz capability

A55-C Motherboard Qualified Vendors Lists (QVL)

ASUS A55-C 1-11

Vendors Part No. Size SS/ DS

Chip Brand Chip No. Timing Voltage DIMM support

1DIMM 2DIMMs A-DATA AM2U16BC2P1 2GB SS A-DATA 3CCD-1509A EL1126T - - . A-DATA AM2U16BC4P2 4GB DS A-DATA 3CCD-1509A EL1126T - - . . A-DATA AX3U1600GC4G9-2G(XMP) 8GB(2 x 4GB) DS - - 9-9-9-24 1.55V-1.75V . . A-DATA AX3U1600XC4G79-2X(XMP) 8GB(2 x 4GB) DS - - 7-9-7-21 1.55V-1.75V . . Apacer 78.B1GE3.9L10C 4GB DS Apacer AM5D5908DEQSCK - - . . CORSAIR CMD12GX3M6A1600C8(XMP) 12GB(6x2GB) DS - - 8-8-8-24 1.65V . . CORSAIR CMZ32GX3M4X1600C10(XMP) 32GB(8GBx4) DS - - 10-10-10-27 1.50V . . CORSAIR CMZ4GX3M1A1600C9 4GB DS - N/A - - . . CORSAIR CMP4GX3M2A1600C8(XMP) 4GB(2 x 2GB) DS - - 8-8-8-24 1.65V . . CORSAIR CMP4GX3M2A1600C9(XMP) 4GB(2 x 2GB) DS - - 9-9-9-24 1.65V . . CORSAIR CMP4GX3M2C1600C7(XMP) 4GB(2 x 2GB) DS - - 7-8-7-20 1.65V . . CORSAIR CMX4GX3M2A1600C9(XMP) 4GB(2 x 2GB) DS - - 9-9-9-24 1.65V . . CORSAIR CMX4GX3M2A1600C9(XMP) 4GB(2 x 2GB) DS - - 9-9-9-24 1.65V . . CORSAIR TR3X6G1600C8 G(XMP) 6GB(3 x 2GB) DS - - 8-8-8-24 1.65V . . CORSAIR TR3X6G1600C8D G(XMP) 6GB(3 x 2GB) DS - - 8-8-8-24 1.65V . . CORSAIR TR3X6G1600C9 G(XMP) 6GB(3 x 2GB) DS - - 9-9-9-24 1.65V . . CORSAIR CMP8GX3M2A1600C9(XMP) 8GB(2 x 4GB) DS - - 9-9-9-24 1.65V . . CORSAIR CMZ8GX3M2A1600C7R(XMP) 8GB(2 x 4GB) DS - - 7-8-7-20 1.50V . . CORSAIR CMX8GX3M4A1600C9(XMP) 8GB(4 x 2GB) DS - - 9-9-9-24 1.65V . . Crucial BL25664BN1608.16FF(XMP) 6GB(3 x 2GB) DS - - - - . . G.SKILL F3-12800CL7D-4GBRH(XMP) 4GB(2 x 2GB) SS - - 7-7-7-24 1.6V . . G.SKILL F3-12800CL7D-4GBECO(XMP) 4GB(2 x 2GB) DS - - 7-7-8-24 XMP 1.35V . . G.SKILL F3-12800CL7D-4GBRM(XMP) 4GB(2 x 2GB) DS - - 7-8-7-24 1.6V . . G.SKILL F3-12800CL8D-4GBRM(XMP) 4GB(2 x 2GB) DS - - 8-8-8-24 1.60V . . G.SKILL F3-12800CL9D-4GBECO(XMP) 4GB(2 x 2GB) DS - - 9-9-9-24 XMP 1.35V . . G.SKILL F3-12800CL9D-4GBRL(XMP) 4GB(2 x 2GB) DS - - 9-9-9-24 1.5V . . G.SKILL F3-12800CL9T-6GBNQ(XMP) 6GB(3 x 2GB) DS - - 9-9-9-24 1.5V~1.6V . . G.SKILL F3-12800CL7D-8GBRH(XMP) 8GB(2 x 4GB) DS - - 7-8-7-24 1.6V . . G.SKILL F3-12800CL8D-8GBECO(XMP) 8GB(2 x 4GB) DS - - 8-8-8-24 XMP 1.35V . . G.SKILL F3-12800CL9D-8GBRL(XMP) 8GB(2 x 4GB) DS - - 9-9-9-24 1.5V . . GEIL GET316GB1600C9QC(XMP) 16GB ( 4x 4GB ) DS - - 9-9-9-28 1.6V . . GEIL GV34GB1600C8DC(XMP) 2GB DS - - 8-8-8-28 1.6V . . HYNIX HMT351U6CFR8C-PB 4GB DS HYNIX H5TQ2G83CFR PBC - - . . KINGMAX FLGE85F-B8KJ9A FEIS(XMP) 2GB DS - - - - . . KINGMAX FLGE85F-B8MF7 MEEH(XMP) 2GB DS - - 7 - . . KINGSTON KHX1600C9D3P1K2/4G 4GB(2 x 2GB) SS - - - 1.5V . . KINGSTON KHX1600C9D3K3/12GX(XMP) 12GB(3x4GB) DS - - 9-9-9-27 1.65V . . KINGSTON KHX1600C9D3T1BK3/12GX(XMP) 12GB(3x4GB) DS - - 9-9-9-27 1.65V . . KINGSTON KHX1600C9D3K4/16GX(XMP) 16GB ( 4GB x4 ) DS - - - 1.65V . . KINGSTON KHX1600C10D3B1K2/16G 16GB(8GBx2) DS - - - 1.5V . . KINGSTON KHX16C9K2/16 16GB(8GBx2) DS - - - 1.5V . . KINGSTON KHX1600C9AD3/2G 2GB DS - - - 1.65V . . KINGSTON KVR1600D3N11/2G-ES 2GB DS KTC D1288JPNDPLD9U 11-11-11-28 1.35V-1.5V . . KINGSTON KHX1600C7D3K2/4GX(XMP) 4GB ( 2x 2GB ) DS - - - 1.65V . . KINGSTON KHX1600C8D3K2/4GX(XMP) 4GB(2 x 2GB) DS - - 8 1.65V . . KINGSTON KHX1600C8D3T1K2/4GX(XMP) 4GB(2 x 2GB) DS - - 8 1.65V . . KINGSTON KHX1600C9D3K2/4GX(XMP) 4GB(2 x 2GB) DS - - 9 1.65V . . KINGSTON KHX1600C9D3LK2/4GX(XMP) 4GB(2 x 2GB) DS - - 9 XMP 1.35V . . KINGSTON KHX1600C9D3X2K2/4GX(XMP) 4GB(2 x 2GB) DS - - 9-9-9-27 1.65V . . KINGSTON KHX1600C9D3T1K3/6GX(XMP) 6GB ( 3x 2GB ) DS - - - 1.65V . . KINGSTON KHX1600C9D3K3/6GX(XMP) 6GB(3 x 2GB) DS - - 9 1.65V . . KINGSTON KHX1600C9D3T1BK3/6GX(XMP) 6GB(3 x 2GB) DS - - 9-9-9-27 1.65V . . KINGSTON KHX1600C9D3K2/8GX(XMP) 8GB(2 x 4GB) DS - - 9-9-9-27 1.65V . KINGSTON KHX1600C9D3P1K2/8G 8GB(2 x 4GB) DS - - - 1.5V . . Super Talent WA160UX6G9 6GB(3 x 2GB) DS - - 9 - . . Samsung M379B5773DHO-YKO 4GB DS Samsung GEA183GSU 11-11-11-28 1.5V . . SanMax SMD-4G68HP-16KZ 4GB DS HYNIX H5TQ2G83BFR PBC - - . . Apacer 78.B1GE3.9L10C 4GB DS Apacer AM5D5908DEQSCK - - . . KINGSTON KHX1600C10D3B1K2/16G 16GB(8GBx2) DS - - - 1.5V . . KINGSTON KHX16C9K2/16 16GB(8GBx2) DS - - - 1.5V . . Elixir M2X8G64CB8HB5N-DG(XMP) 8GB DS Elixir N2CB4G8BOBN-DG - - . .

DDR3-1600 MHz capability

Chapter 1: Product introduction1-12

Vendors Part No. Size SS/DS Chip Brand Chip No. Timing Voltage DIMM socket support 1DIMM 2DIMMs

A-DATA AD3U1333C2G9 2GB SS A-DATA 3CCD-1509HNA1126L - - . . A-DATA AM2U139C2P1 2GB SS ADATA 3CCD-1509A EL1127T - - . . A-DATA AX3U1333C2G9-BP 2GB SS - - - - . .

A-DATA AXDU1333GC2G9-2G(XMP) 4GB (2 x 2GB) SS - - 9-9-9-24 1.25V-1.35V

(low voltage) . .

A-DATA AD63I1C1624EV 4GB DS A-Data 3CCA-1509A - - . . A-DATA AM2U139C4P2 4GB DS ADATA 3CCD-1509A EL1127T - - . . A-DATA SU3U1333W8G9-B 8GB DS ELPIDA J4208BASE-DJ-F - - . . Apacer 78.A1GC6.9L1 2GB DS Apacer AM5D5808DEWSBG - - . . Apacer 78.A1GC6.9L1 2GB DS Apacer AM5D5808FEQSBG 9 - . . Apacer AU02GFA33C9NBGC 2GB DS Apacer AM5D5808APQSBG - - . . Apacer 78.B1GDE.9L10C 4GB DS Apacer AM5D5908CEHSBG - - . .

CORSAIR TR3X6G1333C9 G 6GB (3x 2GB) SS - - 9-9-9-24 1.50V . .

CORSAIR CMD24GX3M6A1333C9(XMP) 24GB (6x4GB) DS - - 9-9-9-24 1.60V . .

CORSAIR TW3X4G1333C9D G 4GB (2 x 2GB) DS - - 9-9-9-24 1.50V . .

CORSAIR CM3X4GA1333C9N2 4GB DS CORSAIR 256MBDCJGELC0401136 9-9-9-24 - . . CORSAIR CMX4GX3M1A1333C9 4GB DS - - 9-9-9-24 1.50V . .

CORSAIR CMD8GX3M4A1333C7 8GB (4 x 2GB) DS - - 7-7-7-20 1.60V . .

Crucial CT25664BA1339.16FF 2GB DS Micron 9KF27D9KPT 9 - . .

Crucial BL25664BN1337.16FF (XMP) 6GB (3 x 2GB) DS - - 7-7-7-24 1.65V . .

ELPIDA EBJ21UE8EDF0-DJ-F 2GB DS ELPIDA J1108EDSE-DJ-F - 1.35V (low voltage) . .

G.SKILL F3-10666CL8D-4GBECO(XMP) 4GB (2 x 2GB) DS - - 8-8-8-8-24 XMP 1.35V . .

G.SKILL F3-10666CL7D-8GBRH(XMP) 8GB (2 x 4GB) DS - - 7-7-7-21 1.5V . .

GEIL GG34GB1333C9DC 4GB (2 x 2GB) DS GEIL GL1L128M88BA12N 9-9-9-24 1.3V

(low voltage) . .

GEIL GV34GB1333C9DC 4GB (2 x 2GB) DS - - 9-9-9-24 1.5V . .

GEIL GVP34GB1333C7DC 4GB (2 x 2GB) DS - - 7-7-7-24 1.5V . .

Hynix HMT325U6BFR8C-H9 2GB SS Hynix H5TQ2G83BFRH9C - - . .

Hynix HMT125U6TFR8A-H9 2GB DS Hynix H5TC1G83TFRH9A - 1.35V (low voltage) . .

Hynix HMT351U6BFR8C-H9 4GB DS Hynix H5TQ2G83BFRH9C - - . . KINGMAX FLFE85F-C8KF9 CAES 2GB SS KINGMAX KFC8FMFXF-DXX-15A - - . . KINGMAX FLFE85F-C8KL9 NAES 2GB SS KINGMAX KFC8FNLXF-DXX-15A - - . . KINGMAX FLFE85F-C8KM9 NAES 2GB SS KINGMAX KFC8FNMXF-BXX-15A - - . . KINGMAX FLFE85F-B8KL9 NEES 2GB DS KINGMAX KKB8FNWBFGNX-26A - - . . KINGMAX FLFF65F-C8KL9 NEES 4GB DS KINGMAX KFC8FNLXF-DXX-15A - - . . KINGMAX FLFF65F-C8KM9 NEES 4GB DS KINGMAX KFC8FNMXF-BXX-15A - - . . KINGSTON KVR1333D3N9/2G 2GB SS Hynix H5TQ2G83AFRH9C 9 - . . KINGSTON KVR1333D3S8N9/2G 2GB SS Micron IID77 D9LGK - 1.5V . . KINGSTON KVR1333D3S8N9/2G-SP 2GB SS ELPIDA J2108BCSE-DJ-F - 1.5V . . KINGSTON KVR1333D3N9/2G 2GB DS ELPIDA J1108BFBG-DJ-F 9 1.5V . . KINGSTON KVR1333D3N9/2G 2GB DS KTC D1288JPNDPLD9U 9 1.5V . . KINGSTON KVR1333D3N9/2G 2GB DS ELPIDA J1108BDSE-DJ-F 9 1.5V . . KINGSTON KVR1333D3N9/2G-SP 2GB DS KTC D1288JEMFNGD9U - 1.5V . . KINGSTON KVR1333D3N9/2G-SP 2GB DS KINGSTON D1288JPSFPGD9U - 1.5V . .

KINGSTON KHX1333C7D3K2/4GX(XMP) 4GB (2 x 2GB) DS - - 7 1.65V . .

KINGSTON KHX1333C9D3UK2/4GX(XMP) 4GB (2 x 2GB) DS - - 9 XMP 1.25V . .

DDR3-1333 MHz capability

ASUS A55-C 1-13

Vendors Part No. Size SS/ DS Chip Brand Chip No. Timing Voltage

DIMM socket support (optional) 1DIMM 2DIMMs

A-DATA DDR3 1333(9) 4Gx16 4GB DS ADATA 3CCA-1509AEL1112T - - . . Apacer AU04GFA33C9QBGC 4GB DS Apacer AM5D5908CEHSBG - - . . GEIL 4G DDR3-1333 4GB DS Geil GL1L258M088BA15N 9/10 1.5V . . KINGSTON KVR1333D3N9/4G 4GB DS ELPIDA J2108BCSE-DJ-F - 1.5V . . KINGSTON KVR1333D3N9/4G 4GB DS KTC D2568JENCNGD9U - 1.5V . . KINGSTON KVR1333D3N9/4G 4GB DS Hynix H5TQ2G83AFR - - . . KINGSTON KVR1333D3N9/4G-SP 4GB DS KINGSTON D2568JENCPGD9U - 1.5V . . KINGSTON KVR1333D3N9/4G 4GB DS Elpida J2108BCSE-DJ-F - 1.5V . . Kingstek KSTD3PC-10600U 4GB DS Kingston KST3D2G1333 - - . . Kingtiger 4GB DIMM PC3-10600 4GB DS Micron OWD77D9LGK - - . . Micron MT8JTF25664AZ-1G4D1 2GB SS Micron OJD12D9LGK - - . . Micron MT8JTF25664AZ-1G4M1 2GB SS MICRON IJM22 D9PFJ - - . . Micron MT16JTF25664AZ-1G4F1 2GB DS Micron 9KF27D9KPT 9 - . . Micron MT16JTF51264AZ-1G4D1 4GB DS Micron OLD22D9LGK - - . . NANYA NT4GC64B8HG0NF-CG 4GB DS NANYA NT5CB256M8GN-CG - - . . PSC AL8F8G73F-DJ2 2GB DS PSC A3P1GF3FGF - - . . SAMSUNG M378B5773DH0-CH9 2GB SS SAMSUNG K4B2G0846D - - . . SAMSUNG M378B5673FH0-CH9 2GB DS SAMSUNG K4B1G0846F - - . . SAMSUNG M378B5273CH0-CH9 4GB DS SAMSUNG K4B2G0846C - - . . Super Talent W1333UB2GS 2GB DS SAMSUNG K4B1G0846F 9 - . . Super Talent W1333UB4GS 4GB DS SAMSUNG K4B2G0846C - - . .

Super Talent W1333UX6GM 6GB (3x 2GB) DS Micron 0BF27D9KPT 9-9-9-24 1.5V . .

KINGSTEK KSTD3PC-10600 2GB SS MICRON PE911-125E - - . .

DDR3-1333 MHz capability

Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage

DIMM socket support (Optional) 1 DIMM 2 DIMMs

Crucial CT12864BA1067.8FF 1GB SS Micron 9GF22D9KPT 7 - Elpida EBJ21UE8EDF0-AE-F 2GB DS Elpida J1108EDSE-DJ-F - 1.35V Kingston KVR1066D3N7/1G 1GB SS Elpida J1108BFSE-DJ-F 7 1.5V Kingston KVR1066D3N7/4G 4GB DS Hynix H5TQ2G83AFR 7 1.5V

DDR3-1066 MHz capability

SS - Single-sided* / DS - Double-sided** DIMM support:

A*: Supports one (1) module inserted into any slot as Single-channel memory configuration.

B**: Supports two (2) modules inserted into both slots as one pair of a dual-channel memory configuration.

Visit the ASUS website at www.asus.com for the latest QVL.

Chapter 1: Product introduction1-14

1.5.3 Installing a DIMM

1

2

3

A

To remove a DIMM

B

A

ASUS A55-C 1-15

1.6 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support.

Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.

1.6.1 Installing an expansion card To install an expansion card:

1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card.

2. Remove the system unit cover (if your motherboard is already installed in a chassis).

3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use.

4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.

5. Secure the card to the chassis with the screw you removed earlier.

6. Replace the system cover.

When using PCI cards on shared slots, ensure that the drivers support Share IRQ or that the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.

1.6.3 PCI slots The PCI slot supports cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications.

1.6.2 Configuring an expansion card After installing the expansion card, configure it by adjusting the software settings.

1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for information on BIOS setup.

2. Assign an IRQ to the card.

3. Install the software drivers for the expansion card.

1.6.4 PCI Express x1 slots This motherboard supports PCI Express x1 network cards, SCSI cards, and other cards that comply with the PCI Express specifications.

1.6.5 PCI Express x16 slot This motherboard supports one PCI Express x16 graphics card that comply with the PCI Express specifications.

Chapter 1: Product introduction1-16

IRQ assignments for this motherboard

Component A B C D E F G H

PCIEx16 shared

PCIEx1_1 shared PCIEx1_2 shared PCIEx1_3 shared PCI1 slot shared PCI2 slot shared PCI3 slot shared Realtek 8111F controller shared HD audio shared SATA controller shared Onboard USB1.0 controller shared Onboard USB2.0 controller shared

ASUS A55-C 1-17

1.7 Jumpers 1. Clear RTC RAM (CLRTC)

This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM:

Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure!

1. Turn OFF the computer and unplug the power cord.

2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2.

3. Plug the power cord and turn ON the computer.

4. Hold down the key during the boot process and enter BIOS setup to reenter data.

If the steps above do not help, remove the onboard battery and move the jumper again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.

You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the CPU Parameter Recall (C.P.R) feature. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values.

A55-C

A55-C Clear RTC RAM

1 2 2 3

Normal (Default)

Clear RTC

CLRTC

Chapter 1: Product introduction1-18

2. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. When you set this jumper to pins 2-3 (+5VSB), you can wake up the computer by pressing a key on the keyboard. This feature requires an ATX power supply that can provide at least 1A on the +5VSB lead, and a corresponding setting in the BIOS.

A55-C

A55-C Keyboard Power

1 2 2 3

+5V (Default)

+5VSB

KBPWR

3. USB device wake-up (3-pin USBPW1~6; 3-pin USBPW7~10) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode).

A55-C

A55-C USB device wake up

1 2 2 3

+5V +5VSB

USBPW1~6

(Default)

1 2 2 3

+5V +5VSB

USBPW7~10

(Default)

ASUS A55-C 1-19

1.8 Connectors 1.8.1 Rear panel ports

1. PS/2 Mouse port (green). This port is for a PS/2 mouse.

2. COM port. This port is for pointing devices or other serial devices.

3. LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub.

LAN port LED indications

Activity/Link LED Speed LED Status Description Status Description OFF No link OFF 10Mbps connection ORANGE Linked ORANGE 100Mbps connection BLINKING Data activity GREEN 1Gbps connection

LAN port

SPEED LED

ACT/LINK LED

4. Line In port (light blue). This port connects to the tape, CD, DVD player, or other audio sources.

5. Line Out port (lime). This port connects to a headphone or a speaker. In the 4, 6 and 8-channel configurations, the function of this port becomes Front Speaker Out.

6. Microphone port (pink). This port connects to a microphone.

89

3

7

1

11

4 5

6

2

10

Refer to the audio configuration table below for the function of the audio ports in the 2, 4, 6, or 8-channel configuration.

Audio 2, 4, 6, or 8-channel configuration

Port Headset 2-channel 4-channel 6-channel 8-channel

Light Blue (Rear panel) Line In Rear Speaker Out Rear Speaker Out Rear Speaker Out

Lime (Rear panel) Line Out Front Speaker Out Front Speaker Out Front Speaker Out Pink (Rear panel) Mic In Mic In Bass/Center Bass/Center Lime (Front panel) Side Speaker Out

Chapter 1: Product introduction1-20

7. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1 devices.

8. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1 devices.

9. USB 2.0 ports 5 and 6. These two 4-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1 devices.

10. Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other VGA-compatible devices.

11. PS/2 Keyboard port (purple). This port is for a PS/2 keyboard.

ASUS A55-C 1-21

1.8.2 Internal connectors 1. CPU and chassis fan connectors (4-pin CPU_FAN, and 3-pin CHA_FAN)

Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector.

The CPU_FAN connector supports a maximum of 2A (24 W) of fan power.

DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors.

A55-C

A55-C Fan connectors

CPU_FAN

C P

U F

A N

P W

M C

P U

F A

N IN

C P

U F

A N

P W

R G

N D

CHA_FAN

Rotation +12V GND

Chapter 1: Product introduction1-22

2. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.

We recommend that you use an ATX 12V Specification 2.0-compliant power supply unit (PSU) with a minimum of 300W power rating. This PSU type has 24-pin and 4-pin power plugs.

If you intend to use a PSU with 20-pin and 4-pin power plugs, ensure that the 20-pin power plug can provide at least 15 A on +12 V and that the PSU has a minimum power rating of 300W. The system may become unstable or may not boot up if the power is inadequate.

DO NOT forget to connect the 4-pin ATX +12V power plug. Otherwise, the system will not boot up.

We recommend that you use a PSU with higher power output when configuring a system with more power-consuming devices or when you intend to install additional devices. The system may become unstable or may not boot up if the power is inadequate.

If you are uncertain about the minimum power supply requirement for your system, refer to the Recommended Power Supply Wattage Calculator at http://support.asus. com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.

A55-C

A55-C ATX power connectors

PIN 1

EATXPWR

PIN 1

GND +5 Volts +5 Volts +5 Volts -5 Volts GND GND GND PSON# GND -12 Volts +3 Volts

+3 Volts +12 Volts +12 Volts

+5V Standby Power OK

GND +5 Volts

GND +5 Volts

GND +3 Volts +3 Volts

ATX12V

+ 12

V D

C +

12 V

D C

G N

D G

N D

ASUS A55-C 1-23

3. Serial ATA 3.0 Gb/s connectors (7-pin SATA3G_1~6) These connectors are for the Serial ATA 3.0 Gb/s signal cables for Serial ATA hard disk drives and optical disc drives. If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1, or RAID 10 configuration through the onboard controller.

These connectors are set to AHCI mode by default. If you intend to create a Serial ATA RAID set using these connectors, set the type of the SATA connectors in the BIOS to [RAID]. See section 2.5.2 SATA Configuration for details.

You must install Windows XP Service Pack 3 or later version before using Serial ATA hard disk drives. The Serial ATA RAID feature is available only if you are using Windows XP SP3 or later version.

When using hot-plug and NCQ, set the type of the SATA connectors in the BIOS to [AHCI]. See section 2.5.2 SATA Configuration for details.

SATA3G_5

G N

D R

S A

T A

_R X

P 5

R S

A T

A _R

X N

5 G

N D

R S

A T

A _T

X N

5 R

S A

T A

_T X

P 5

G N

D

SATA3G_3

G N

D R

S A

T A

_R X

P 3

R S

A T

A _R

X N

3 G

N D

R S

A T

A _T

X N

3 R

S A

T A

_T X

P 3

G N

D

SATA3G_1

G N

D R

S A

T A

_R X

P 1

R S

A T

A _R

X N

1 G

N D

R S

A T

A _T

X N

1 R

S A

T A

_T X

P 1

G N

D

SATA3G_6

G N

D R

S A

T A

_T X

P 6

R S

A T

A _T

X N

6 G

N D

R S

A T

A _R

X N

6 R

S A

T A

_R X

P 6

G N

D

SATA3G_4

G N

D R

S A

T A

_T X

P 4

R S

A T

A _T

X N

4 G

N D

R S

A T

A _R

X N

4 R

S A

T A

_R X

P 4

G N

D

SATA3G_2

G N

D R

S A

T A

_T X

P 2

R S

A T

A _T

X N

2 G

N D

R S

A T

A _R

X N

2 R

S A

T A

_R X

P 2

G N

D

A55-C

A55-C SATA 3.0Gb/s connectors

Chapter 1: Product introduction1-24

4. System panel connector (10-1 pin F_PANEL) This connector supports several chassis-mounted functions.

System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.

Hard disk drive activity LED (2-pin +HDLED) This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The HD LED lights up or flashes when data is read from or written to the HDD.

ATX power button/soft-off button (2-pin PWRBTN) This 2-pin connector is for the system power button.

Reset button (2-pin RESET) This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power.

A55-C

A55-C System panel connector

PIN 1

PWR BTN

PL ED

+ PL

ED -

PW R

G N

D

H D

_L ED

+ H

D _L

ED -

G ro

un d

H W

R ST

# (N

C )

F_PANEL PWR LED

+HD_LED RESET

ASUS A55-C 1-25

We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard high-definition audio capability.

If you want to connect a high definition front panel audio module to this connector, set the Front Panel Type item in the BIOS to [HD]. See section 2.5.5 Onboard Devices Configuration for details.

The front panel audio I/O module is purchased separately.

5. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either High Definition Audio or AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.

A55-C

A55-C Front panel audio connector

AAFP PIN 1

A G

N D

N C

S E

N S

E 1_

R E

T U

R

S E

N S

E 2_

R E

T U

R

P O

R T

1 L

P O

R T

1 R

P O

R T

2 R

S E

N S

E _S

E N

D P

O R

T 2

L

HD-audio-compliant pin definition

PIN 1

A G

N D

N C

N C

N C

M IC

2 M

IC P

W R

Li ne

o ut

_R N C

Li ne

o ut

_L

Legacy AC97 compliant definition

6. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis comopnent is removed or replaced. The signal is then generated as a chassis intrusion event. By default, the pin labeled Chassis Signal and Ground are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature.

A55-C

A55-C Chassis intrusion connector

+ 5V

S B

_M B

C ha

ss is

S ig

na l

G N

D

CHASSIS

Chapter 1: Product introduction1-26

7. USB 2.0 connectors (10-1 pin USB78, USB910) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480Mbps connection speed.

Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!

The USB 2.0 module is purchased separately.

A55-C

A55-C USB2.0 connectors

PI N

1

U SB

+5 V

U SB

_P 10

- U

SB _P

10 +

G N

D

U SB

+5 V

U SB

_P 9-

U SB

_P 9+

G N

D N

C

USB910

PI N

1

U SB

+5 V

U SB

_P 8-

U SB

_P 8+

G N

D

U SB

+5 V

U SB

_P 7-

U SB

_P 7+

G N

D N

C

USB78

8. Speaker connector (4-pin SPEAKER) This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings.

A55-C

A55-C Speaker Out Connector

+ 5V

G N

D G

N D

S pe

ak er

O ut

SPEAKER

PIN 1

ASUS A55-C 1-27

1.9 Software support 1.9.1 Installing an operating system This motherboard supports Windows XP / Vista / Windows 7 / Windows 8 Operating Systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware.

Motherboard settings and hardware options vary. Refer to your OS documentation for detailed information.

Ensure that you install Windows XP Service Pack 3 or later versions / Windows Vista Service Pack 1 or later versions before installing the drivers for better compatibility and system stability.

1.9.2 Support DVD information The Support DVD that comes with the motherboard package contains the drivers, software applications, and utilities that you can install to avail all motherboard features.

The contents of the Support DVD are subject to change at any time without notice. Visit the ASUS website at www.asus.com for updates.

To run the Support DVD Place the Support DVD into the optical drive. If Autorun is enabled in your computer, the DVD automatically displays the Specials screen. Click Drivers, Utilities, Make Disk, Manual, and Contact tabs to display their respective menus.

If Autorun is NOT enabled on your computer, browse the contents of the Support DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run the DVD.

Click an item to install

Click an icon to display Support DVD/motherboard information

The following screen is for reference only.

Chapter 1: Product introduction1-28

Chapter 2: BIOS information 2-1

2.1 Managing and updating your BIOS

Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update utility.

2.1.1 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows environment.

ASUS Update requires an Internet connection either through a network or an Internet Service Provider (ISP).

This utility is available in the support DVD that comes with the motherboard package.

Installing ASUS Update To install ASUS Update:

1. Place the support DVD in the optical drive. The Specials menu appears.

2. Click the Utilities tab, then click AI Suite II.

3. Follow the onscreen instructions to complete the installation.

Quit all Windows applications before you update the BIOS using this utility.

Updating the BIOS To update the BIOS:

1. From the Windows desktop, click Start > Programs > ASUS > AI Suite II > AI Suite II X.XX.XX to launch the AI Suite II utility. The AI Suite II Quick Bar appears.

2. Click Update button from the Quick Bar, and then click ASUS Update from the popup menu. The ASUS Update main screen appears. From the list, select either of the following methods:

BIOS information 2

2-2 ASUS A55-C

Updating from the Internet

a. Select Update BIOS from the Internet, then click Next.

b. Select the ASUS FTP site nearest you to avoid network traffic, then click Next.

c. From the FTP site, select the BIOS version that you wish to download then click Next.

The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features.

Updating from a BIOS file

a. Select Update BIOS from file, then click Next.

b. Locate the BIOS file from the Open window, then click Open.

3. Follow the onscreen instructions to complete the updating process.

2.1.2 ASUS EZ Flash 2 The ASUS EZ Flash 2 feature allows you to update the BIOS without using an OS-based utility.

Before you start using this utility, download the latest BIOS file from the ASUS website at www.asus.com.

To update the BIOS using EZ Flash 2:

1. Insert the USB flash disk that contains the latest BIOS file to the USB port.

2. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select ASUS EZ Flash 2 Utility and press to enable it.

3. Press to switch to the Drive field.

4. Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS, and then press .

5. Press to switch to the Folder Info field.

6. Press the Up/Down arrow keys to find the BIOS file, and then press to perform the BIOS update process. Reboot the system when the update process is done.

This feature supports USB flash disks formatted using FAT 32/16 on a single partition.

DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure!

Chapter 2: BIOS information 2-3

2.1.3 ASUS CrashFree BIOS 3 utility The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS file using the motherboard support DVD or a USB flash drive that contains the updated BIOS file.

Before using this utility, rename the BIOS file in the removable device into A55C.CAP.

The BIOS file in the support DVD may not be the latest version. Download the latest BIOS file from the ASUS website at www.asus.com.

Recovering the BIOS To recover the BIOS:

1. Turn on the system.

2. Insert the support DVD to the optical drive or the USB flash drive that contains the BIOS file to the USB port.

3. The utility automatically checks the devices for the BIOS file. When found, the utility reads the BIOS file and enters ASUS EZ Flash 2 utility automatically.

4. The system requires you to enter BIOS Setup to recover BIOS setting. To ensure system compatibility and stability, we recommend that you press to load default BIOS values.

DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure!

2-4 ASUS A55-C

Welcome to FreeDOS (http://www.freedos.org)! C:\>d: D:\>

3. When the Make Disk menu appears, select the FreeDOS command prompt item by pressing the item number.

4. At the FreeDOS prompt, type d: and press to switch the disk from Drive C (optical drive) to Drive D (USB flash drive).

Please select boot device:

SATA: XXXXXXXXXXXXXXXX USB XXXXXXXXXXXXXXXXX UEFI: XXXXXXXXXXXXXXXX Enter Setup

and to move selection ENTER to select boot device ESC to boot using defaults

2.1.4 ASUS BIOS Updater The ASUS BIOS Updater allows you to update BIOS in DOS environment. This utility also allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or gets corrupted during the updating process.

The succeeding utility screens are for reference only. The actual utility screen displays may not be same as shown.

Before updating BIOS 1. Prepare the motherboard support DVD and a USB flash drive formatted using FAT

32/16 on a single partition.

2. Download the latest BIOS file and BIOS Updater from the ASUS website at http://support.asus.com and save them on the USB flash drive.

NTFS is not supported under DOS environment. Do not save the BIOS file and BIOS Updater to a hard disk drive or USB flash drive in NTFS format.

3. Turn off the computer and disconnect all SATA hard disk drives (optional).

Booting the system in DOS environment 1. Insert the USB flash drive with the latest BIOS file and BIOS Updater to the USB port.

2. Boot your computer. When the ASUS Logo appears, press to show the BIOS Boot Device Select Menu. Insert the support DVD into the optical drive and select the optical drive as the boot device.

Chapter 2: BIOS information 2-5

Updating the BIOS file To update the BIOS file using BIOS Updater

1. At the FreeDOS prompt, type bupdater /pc /g and press .

ASUSTek BIOS Updater for DOS V1.30

Current ROM Update ROM

A:

Note [Enter] Select or Load [Tab] Switch [V] Drive Info

[Up/Down/Home/End] Move [B] Backup [Esc] Exit

A55C.CAP 8390656 2012-11-19 17:30:48

PATH: A:\

BOARD: A55-C VER: 0208 DATE: 11/19/2012

BOARD: Unknown VER: Unknown DATE: Unknown

D:\>bupdater /pc /g

2. The BIOS Updater screen appears as below.

3. Press to switch between screen fields and use the keys to select the BIOS file and press . BIOS Updater checks the selected BIOS file and prompts you to confirm BIOS update.

Are you sure to update BIOS?

Yes No

4. Select Yes and press . When BIOS update is done, press to exit BIOS Updater. Restart your computer.

DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure!

For BIOS Updater version 1.30 or later, the utility automatically exits to the DOS prompt after updating BIOS.

Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under theExit menu. Refer to section 2.9 Exit menu for details.

Ensure to connect all SATA hard disk drives after updating the BIOS file if you have disconnected them.

2-6 ASUS A55-C

Using the power button, reset button, or the + + keys to force reset from a running operating system can cause damage to your data or system. We recommend to always shut down the system properly from the operating system.

2.2 BIOS setup program Use the BIOS Setup program to update the BIOS or configure its parameters. The BIOS screens include navigation keys and brief online help to guide you in using the BIOS Setup program.

Entering BIOS Setup at startup To enter BIOS Setup at startup: Press during the Power-On Self Test (POST). If you do not press ,

POST continues with its routines.

Entering BIOS Setup after POST To enter BIOS Setup after POST: Press ++ simultaneously. Press the reset button on the system chassis. Press the power button to turn the system off then back on. Do this option only if you

failed to enter BIOS Setup using the first two options.

The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.

Ensure that a USB mouse is connected to your motherboard if you want to use the mouse to control the BIOS setup program.

The default BIOS settings for this motherboard apply for most conditions to ensure optimum performance. If the system becomes unstable after changing any BIOS settings, load the default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit Menu. See section 2.9 Exit Menu.

If the system fails to boot after changing any BIOS setting, try to clear the CMOS and reset the motherboard to the default value. Refer to section 1.7 Jumpers on how to erase the RTC RAM.

The BIOS setup program does not support the bluetooth devices.

BIOS menu screen The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode. You can change modes from the Exit menu or from the Exit/Advanced Mode button in the EZ Mode/Advanced Mode screen.

Chapter 2: BIOS information 2-7

EZ Mode By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ Mode provides you an overview of the basic system information, and allows you to select the display language, system performance mode and boot device priority. To access the Advanced Mode, click Exit/Advanced Mode, then select Advanced Mode or press F7 hot key for the advanced BIOS settings.

The default screen for entering the BIOS setup program can be changed. Refer to the Setup Mode item in section 2.7 Boot menu for details.

The boot device options vary depending on the devices you installed to the system.

The Boot Menu(F8) button is available only when the boot device is installed to the system.

Exits the BIOS setup program without saving the changes, saves the changes and resets the system, or enters the Advanced Mode

Selects the display language of the BIOS setup program

Displays the CPU/motherboard temperature, CPU voltage output, CPU/chassis fan speed

Silent mode Standard mode Turbo mode

Loads optimized default Selects boot device priority Selects the boot device priorityDisplays the system

properties of the selected mode

Selects Advanced mode functions

Switch to Advanced mode

2-8 ASUS A55-C

Advanced Mode The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations.

To access the EZ Mode, click Exit, then select ASUS EZ Mode.

Menu bar The menu bar on top of the screen has the following main items:

Main For changing the basic system configuration Ai Tweaker For changing the overclocking settings Advanced For changing the advanced system settings Monitor For displaying the system temperature, power status, and changing the fan settings Boot For changing the system boot configuration Tool For configuring options for special functions Exit For selecting the exit options and loading default settings

Navigation keys

General helpMenu bar

Submenu item

Configuration fieldsMenu items

Scroll barPop-up window

Back button

Chapter 2: BIOS information 2-9

Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have their respective menu items.

Back button This button appears when entering a submenu. Press or use the USB mouse to click this button to return to the previous menu screen.

Submenu items A greater than sign (>) before each item on any menu screen means that the item has a submenu. To display the submenu, select the item and press or double-click the item.

Pop-up window Select a menu item and press to display a pop-up window with the configuration options for that item.

Scroll bar A scroll bar appears on the right side of a menu screen when there are items that do not fit on the screen. Press the Up/Down arrow keys or

Navigation keys At the bottom right corner of the menu screen are the navigation keys for the BIOS setup program. Use the navigation keys to select items in the menu and change the settings.

General help At the top right corner of the menu screen is a brief description of the selected item.

Configuration fields These fields show the values for the menu items. If an item is user-configurable, you can change the value of the field opposite the item. You cannot select an item that is not user- configurable. A configurable field is highlighted when selected. To change the value of a field, select it and press or click on it to display a list of options.

2-10 ASUS A55-C

2.3 Main menu The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program. The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings.

2.3.1 System Language [English] Allows you to choose the BIOS language version from the options. Configuration options:

[English] [] []

2.3.2 System Date [Day xx/xx/xxxx] Allows you to set the system date.

2.3.3 System Time [xx:xx:xx] Allows you to set the system time.

2.3.4 Security The Security menu items allow you to change the system security settings.

If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC) RAM to clear the BIOS password. See section 1.7 Jumpers for information on how to erase the RTC RAM.

The Administrator or User Password items on top of the screen show the default Not Installed. After you set a password, these items show Installed.

Chapter 2: BIOS information 2-11

Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. Otherwise, you might be able to see or change only selected fields in the BIOS setup program.

To set an administrator password:

1. Select the Administrator Password item and press .

2. From the Create New Password box, key in a password, then press .

3. Confirm the password when prompted.

To change an administrator password:

1. Select the Administrator Password item and press .

2. From the Enter Current Password box, key in the current password, then press .

3. From the Create New Password box, key in a new password, then press .

4. Confirm the password when prompted.

To clear the administrator password, follow the same steps as in changing an administrator password, but press when prompted to create/confirm the password. After you clear the password, the Administrator Password item on top of the screen shows Not Installed.

User Password If you have set a user password, you must enter the user password for accessing the system. The User Password item on top of the screen shows the default Not Installed. After you set a password, this item shows Installed.

To set a user password:

1. Select the User Password item and press .

2. From the Create New Password box, key in a password, then press .

3. Confirm the password when prompted.

To change a user password:

1. Select the User Password item and press .

2. From the Enter Current Password box, key in the current password, then press .

3. From the Create New Password box, key in a new password, then press .

4. Confirm the password when prompted.

To clear the user password, follow the same steps as in changing a user password, but press when prompted to create/confirm the password. After you clear the password, the User Password item on top of the screen shows Not Installed.

2-12 ASUS A55-C

Target CPU Speed : xxxxMHz Displays the current CPU speed.

Target DRAM Speed : xxxxMHz Displays the current DRAM speed.

2.4.1 Ai Overclock Tuner [Auto] Allows you to select the CPU overclocking options to achieve the desired CPU internal frequency. Select any of these preset overclocking configuration options: [Auto] Loads the optimal settings for the system. [D.O.C.P.] If you install memory modules supporting the eXtreme Memory Profile

(D.O.C.P.) technology, select this item to set the profile supported by your memory modules to optimize system performance.

2.4.2 Memory Frequency [Auto] Allows you to set the memory operating frequency. Configuration options: [Auto] [DDR3- 800MHz] [DDR3-1066MHz] [DDR3-1333MHz] [DDR3-1600MHz] [DDR3-1866MHz]

Selecting a very high memory frequency may cause the system to become unstable! If this happens, revert to the default setting.

2.4.3 EPU Power Saving Mode [Disabled] Allows you to enable or disable the EPU power saving function. Configuration options: [Disabled] [Enabled]

EPU Setting [Auto] This item appears only when The EPU Power Saving Mode is set to [Enabled] and allows you to set power saving mode. Configuration options: [Auto] [Light Power Saving Mode] [Medium Power Saving Mode] [Max Power Saving Mode]

2.4 Ai Tweaker menu The Ai Tweaker menu items allow you to configure overclocking-related items.

Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field values can cause the system to malfunction.

The configuration options for this section vary depending on the CPU and DIMM model you installed on the motherboard.

Chapter 2: BIOS information 2-13

2.4.4 DIGI+ VRM CPU Power Phase Control [Standard] Phase number is the number of working VRM phase. Increasing phase number under heavy system loading to get more transient and better thermal performance. Reducing phase number under light system loading to increase VRM efficiency. [Standard] Proceeds phase control depending on the CPU loading. [Optimized] Loads the ASUS optimized phase tuning profile. [Extreme] Proceeds the full phase mode. [Manual Adjustment] Allows manual adjustment.

2-14 ASUS A55-C

Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.

2.5 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices.

2.5.1 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects.

The items shown in submenu may be different due to the CPU you installed.

AMD PowerNow function [Enabled] Enables or disables the AMD PowerNow function. Configuration options: [Enabled] [Disabled]

NX Mode [Enabled] Enables or disables the No-execute page protection function. Configuration options: [Enabled] [Disabled]

SVM [Enabled] Enables or disables CPU virtualization. Configuration options: [Disabled] [Enabled]

CPB Mode [Auto] Disables the CPB (Core Performance Boost) mode or set it to [Auto] for automatic configuration. Configuration options: [Disabled] [Auto]

C6 Mode [Enabled] Enables or disables C6 mode. Configuration options: [Enabled] [Disabled]

IOMMU [Disabled] Set this item to [Enabled] to show IOMMU Mode. Configuration options: [Enabled] [Disabled]

Bank Interleaving [Enabled] Enables or disables Bank Interleaving. Configuration options: [Enabled] [Disabled]

Channel Interleaving [Enabled] Enables or disables Channel Interleaving. Configuration options: [Enabled] [Disabled]

Chapter 2: BIOS information 2-15

2.5.2 SATA Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port.

OnChip SATA Channel [Enabled] Enables or disables onboard channel SATA port. Configuration options: [Disabled] [Enabled]

OnChip SATA Type [IDE] Allows you to set the SATA configuration. [IDE] Set to [IDE] when you want to use the Serial ATA hard disk drives as

Parallel ATA physical storage devices. [RAID] Set to [RAID] when you want to create a RAID configuration from the SATA

hard disk drives. [AHCI] Set to [AHCI] when you want the SATA hard disk drives to use the AHCI

(Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands.

SATA Port 5 - Port 6 [AHCI] This item only appears when OnChip SATA Type is set to [AHCI]. If SATA port 5 and port 6 are configured as [AHCI], the ports can only be used under OS with driver installed. Set to [IDE] instead of [AHCI] to access devices on SATA port 5 and port 6 before entering OS. Configuration options: [AHCI] [IDE]

S.M.A.R.T. Status Check [Enabled] S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during the POST. Configuration options: [Enabled] [Disabled]

2-16 ASUS A55-C

2.5.3 USB Configuration The items in this menu allow you to change the USB-related features.

The USB Devices item shows the auto-detected values. If no USB device is detected, the item shows None.

USB Device Enable [Enabled] [Enabled] Enables available USB devices. [Disabled] Disables available USB devices.

Legacy USB Support [Enabled] [Enabled] Enables the support for USB devices on legacy operating systems (OS). [Disabled] The USB devices can be used only for the BIOS setup program. [Auto] Allows the system to detect the presence of USB devices at startup. If

detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled.

EHCI Hand-off [Disabled] [Enabled] Enables the support for operating systems without an EHCI hand-off

feature. [Disabled] Disables the function.

USB Single Port Control Allows you to enable/disable individual USB ports.

2.5.4 NB Configuration IGFX Multi-Monitor [Disabled] Enables or disables the Internal Graphics Device Multi-Monitor support for add-on VGA devices. And the memory size of Internal Graphics Device will keep memory reserved. Configuration options: [Disabled] [Enabled]

Primary Video Device [PCIE / PCI Video] Selects the primary display device. Configuration options: [IGFX Video] [PCIE / PCI Video]

Integrated Graphics [Auto] Enables the integrated graphics controller. Configuration options: [Auto] [Force]

Chapter 2: BIOS information 2-17

2.5.5 Onboard Devices Configuration HD Audio Device [Enabled] [Enabled] Enables the High Definition Audio Controller. [Disabled] Disables the controller.

The following two items appear only when you set the HD Audio Device item to [Enabled].

Front Panel Type [HD] Allows you to set the front panel audio connector (AAFP) mode to legacy AC97 or high- definition audio depending on the audio standard that the front panel audio module supports. [HD] Sets the front panel audio connector (AAFP) mode to high definition audio. [AC97] Sets the front panel audio connector (AAFP) mode to legacy AC97.

Realtek LAN Controller [Enabled] [Enabled] Enables the Realtek LAN controller. [Disabled] Disables the controller.

Realtek PXE OPROM [Disabled] This item appears only when you set the Realtek LAN Controller item to [Enabled] and allows you to enable or disable the Rom Help of the Realtek LAN controller. Configuration options: [Enabled] [Disabled]

Serial Port Configuration The sub-items in this menu allow you to set the serial port configuration.

Serial Port [Enabled] Allows you to enable or disable the serial port (COM). Configuration options: [Enabled] [Disabled] Change Settings [Auto] Allows you to select the Serial Port base address. Configuration options: [Auto] [IO=3F8h; IRQ=4] [IO=2F8h; IRQ=3] [IO=3E8h; IRQ=4] [IO=2E8h; IRQ=3]

2-18 ASUS A55-C

2.5.6 APM EuP Ready [Disabled] This setting allows the BIOS to reduce power at S5 to prepare the system for EuP. When Enabled, all other PME options will be switched off.

Restore AC Power Loss [Power Off] [Power On] The system goes into on state after an AC power loss. [Power Off] The system goes into off state after an AC power loss. [Last State] The system goes into either off or on state, whatever the system state was

before the AC power loss.

Power On By PME [Disabled] [Disabled] Disables the PME to wake up by PCI/PCIE devices. [Enabled] Allows you to turn on the system through a PCI/PCIE LAN or modem card.

This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.

Power On By Ring [Disabled] [Disabled] Disables Ring to generate a wake event. [Enabled] Enables Ring to generate a wake event.

Power On By RTC [Disabled] [Disabled] Disables RTC to generate a wake event. [Enabled] When set to [Enabled], the items RTC Alarm Date (Days) and Hour/

Minute/Second will become user-configurable with set values.

RTC Alarm Date (Days) This item appears only when you set the previous item to [Enabled] and allows you to select RTC alarm time (days). When you set the time to zero, the RTC alarms everyday. Use <+> and <-> keys to adjust the time. - Hour / - Minute / - Second Allows you to set the RTC alarm time. Use <+> and <-> keys to adjust the time.

Chapter 2: BIOS information 2-19

2.5.7 Network Stack Network Stack [Disabled] This item allows user to disable or enable the UEFI network stack. Configuration options: [Disabled] [Enabled]

Ipv4 PXE Support [Enabled] This item appears only when you set the Network Stack item to [Enabled]. When this item is disabled, the IPV4 PXE boot option will not be created. Configuration options: [Disabled] [Enabled] Ipv6 PXE Support [Enabled] This item appears only when you set the Network Stack item to [Enabled]. When this item is disabled, the IPV6 PXE boot option will not be created. Configuration options: [Disabled] [Enabled]

2-20 ASUS A55-C

2.6 Monitor menu The Monitor menu displays the system temperature/power status, and allows you to change the fan settings.

2.6.1 CPU Temperature / MB Temperature [xxxC/xxxF] The onboard hardware monitor automatically detects and displays the CPU and motherboard temperatures. Select Ignore if you do not wish to display the detected temperatures.

2.6.2 CPU / Chassis fan Speed [xxxx RPM] or [Ignore] / [N/A]

The onboard hardware monitor automatically detects and displays the CPU / chassis fan speeds in rotations per minute (RPM). If the fan is not connected to the motherboard, the field shows N/A. Select Ignore if you do not wish to display the detected speed.

2.6.3 CPU Q-Fan Control [Enabled] [Disabled] Disables the CPU Q-Fan control feature. [Enabled] Enables the CPU Q-Fan control feature.

Fan Speed Low Limit [200 RPM] This item appears only when you enable the CPU Q-Fan Control feature and allows you to disable or set the CPU fan warning speed. Configuration options: [Ignore] [200RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM]

Chapter 2: BIOS information 2-21

Q-Fan Profile [Standard] This item appears only when you enable the CPU Q-Fan Control feature and allows you to set the appropriate performance level of the CPU fan. [Standard] Sets to [Standard] to make the CPU fan automatically adjust depending on

the CPU temperature. [Silent] Sets to [Silent] to minimize the fan speed for quiet CPU fan operation. [Turbo] Sets to [Turbo] to achieve maximum CPU fan speed. [Manual] Sets to [Manual] to assign detailed fan speed control parameters.

The following four items appear only when you set Q-Fan Profile to [Manual].

Q-FAN Upper Temperature [70C] Use the <+> and <-> keys to adjust the upper limit of the CPU temperature. The values range from 20C to 90C. Q-FAN Fan Max. Duty Cycle(%) [100%] Use the <+> and <-> keys to adjust the maximum CPU fan duty cycle. The values range from 40% to 100%. When the CPU temperature reaches the upper limit, the CPU fan will operate at the maximum duty cycle. Q-FAN Lower Temperature [20C] Displays the lower limit of the CPU temperature. Q-FAN Fan Min. Duty Cycle(%) [20%] Use the <+> and <-> keys to adjust the minimum CPU fan duty cycle. When the CPU temperature is under the lower limit, the CPU fan will operate at the minimum duty cycle.

2.6.4 CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. Select Ignore if you do not want to detect this item.

2-22 ASUS A55-C

2.7 Boot menu The Boot menu items allow you to change the system boot options.

Scroll down to display the following items:

Chapter 2: BIOS information 2-23

2.7.1 Fast Boot [Enabled] Enable or disable boot with initialization of a minimal set of devices to launch active boot option. Configuration options: [Disabled] [Enabled]

The following three items appear only when you set Fast Boot to [Enabled].

USB Support [Partial Initialization] [Disabled] All USB devices will not be available until OS boot up for the fastest

POST time possible. [Full Initialization] All USB devices will be available during POST. This setting will

extend POST time. [Partial Initialization] For a faster POST time, only the USB ports with keyboard and

mouse connections will be detected.

PS/2 Keyboard and Mouse Support [Auto] [Auto] For a faster POST time, PS/2 devices are available when the

system boots up or rebooted as long as the PS/2 devices have not been reconnected or changed.

[Full Initialization] For full system control, PS/2 devices are available during POST. This setting will extend POST time.

[Disabled] For a shorter POST time, all PS/2 devices are available only after the PC enters the OS.

Network Stack Driver Support [Disabled] [Disabled] If Disabled, the Network Stack Driver will be skipped. To enable this

feature, enable the Network Stack item in the Advanced menu. [Enabled] Allows the BIOS to boot from the Network Stack Driver.

Next boot after AC Power Loss [Normal Boot] [Normal Boot] Returns to normal boot on the next boot after an AC power loss. [Fast Boot] Accelerates the boot speed on the next boot after an AC power loss.

2.7.2 Full Screen Logo [Enabled] [Enabled] Enables the full screen logo display feature. [Disabled] Disables the full screen logo display feature.

Set this item to [Enabled] to use the ASUS MyLogo 2 feature.

Post Report [5 sec] This item appears only when the Full Screen Logo item is set to [Disabled] and allows you to set the waiting time for the system to display the post report. Configuration options: [1 sec] [2 sec] [3 sec] [4 sec] [5 sec] [6 sec] [7 sec] [8 sec] [9 sec] [10 sec] [Until Press ESC]

2-24 ASUS A55-C

2.7.3 Post Delay Time [3 sec] Allows you to set the POST Report wait time. This configuration only functions in Normal Boot mode. Configuration options: [0 sec] [1 sec] [2 sec] [3 sec] [4 sec] [5 sec] [6 sec] [7 sec] [8 sec] [9 sec] [10 sec]

2.7.4 Bootup NumLock State [On] [On] Sets the power-on state of the NumLock to [On]. [Off] Sets the power-on state of the NumLock to [Off].

2.7.5 Wait for F1 If Error [Enabled] When this item is set to [Enabled], the system waits for the F1 key to be pressed when error occurs. Configuration options: [Disabled] [Enabled]

2.7.6 Option ROM Messages [Force BIOS] [Force BIOS] The third-party ROM messages will be forced to display during the boot

sequence. [Keep Current] The third-party ROM messages will be displayed only if the third-party

manufacturer had set the add-on device to do so.

2.7.7 Interrupt 19 Capture [Postponed] [Immediate] Immediately capture Interrupt 19 during boot process. [Postponed] Postpone capture of Interrupt 19 during boot process.

2.7.8 Setup Mode [EZ Mode] [Advanced Mode] Sets Advanced Mode as the default screen for entering the BIOS setup

program. [EZ Mode] Sets EZ Mode as the default screen for entering the BIOS setup

program.

2.7.9 CSM (Compatibility Support Module) This option controls whether or not CSM (Compatibility Support Module) will be launched.

Launch CSM [Auto] Configuration option: [Auto] [Enabled] [Disabled]

The following four items appear only when you set Launch CSM to [Enabled].

Boot Device Control [UEFI and Legacy OpROM] Configuration option: [UEFI and Legacy OpRom] [Legacy OpROM only] [UEFI only] Boot from Network Devices [Legacy OpROM first] Configuration option: [Legacy OpROM first] [UEFI driver first] [Ignore]

Chapter 2: BIOS information 2-25

2.7.10 Secure Boot This option allows you to configure the Secure Boot related parameters.

OS Type [Other OS] Configuration option: [Windows UEFI mode] [Other OS]

Secure Boot Mode [Standard] This item appears only when you set the OS Type to [Windows UEFI]. Configuration option: [Standard] [Custom]

The following items appear when Secure Boot Mode is set to [Custom].

Key Management

Manage the Secure Boot Keys (PK, KEK, DB, DBX) Install default Secure Boot Keys Configuration options: [Yes] [No]

Platform Key (PK) Load PK from File Configuration options: [Acpi (a0341d0, 0)\PCI (1212)\USB (2, 0)\] Copy PK to File Configuration options: [OK] Delete PK Configuration options: [Yes] [No]

KEK Management (KEK) Load KEK from File Configuration options: [OK] Copy KEK to File Configuration options: [OK] Delete the KEK Configuration options: [Yes] [No] Append KEK from File Configuration options: [OK]

Boot from Storage Devices [Legacy OpRom first] Configuration option: [Both, Legacy OpROM first] [Both, UEFI first] [Legacy OpROM first] [UEFI driver first] [Ignore] Boot from PCIe/PCI Expansion Devices [Legacy OpROM first] Configuration option: [Legacy OpROM first] [UEFI driver first]

2-26 ASUS A55-C

DB Management Load DB from File Configuration options: [OK] Copy DB to File Configuration options: [OK] Delete the DB Configuration options: [Yes] [No] Append DB from File Configuration options: [OK]

DBX Management Load DBX from File Configuration options: [OK] Copy DBX to File Configuration options: [OK] Delete the DBX Configuration options: [Yes] [No] Append DBX from File Configuration options: [OK]

2.7.11 Boot Option Priorities These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system.

To select the boot device during system startup, press when ASUS Logo appears.

To access Windows OS in Safe Mode, press after POST.

2.7.12 Boot Override These items displays the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system. Click an item to start booting from the selected device.

Chapter 2: BIOS information 2-27

2.8 Tools menu The Tools menu items allow you to configure options for special functions. Select an item then press to display the submenu.

2.8.1 ASUS EZ Flash 2 Utility Allows you to run ASUS EZ Flash 2. Press [Enter] to launch the ASUS EZ Flash 2 screen.

For more details, see section 2.1.2 ASUS EZ Flash 2.

2.8.3 ASUS O.C. Profile This item allows you to store or load multiple BIOS settings.

The Setup Profile Status items show Not Installed if no profile is created.

Label Allows you to input the label of the setup profile.

Save to Profile Allows you to save the current BIOS settings to the BIOS Flash, and create a profile. Key in a profile number from one to eight, press , and then select Yes.

Load from Profile Allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile number that saved your CMOS settings, press , and then select Yes.

DO NOT shut down or reset the system while updating the BIOS to prevent the system boot failure!

We recommend that you update the BIOS file only coming from the same memory/ CPU configuration and BIOS version.

2.8.2 ASUS SPD Information DIMM Slot # [DIMM_A1] Displays the Serial Presence Detect (SPD) information of the DIMM module installed on the selected slot. Configuration options: [DIMM_A1] [DIMM_B1]

2-28 ASUS A55-C

2.9 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit menu.

Load Optimized Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select Yes to load the default values.

Save Changes & Reset Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved. When you select this option or if you press , a confirmation window appears. Select Yes to save changes and exit.

Discard Changes & Exit This option allows you to exit the Setup program without saving your changes. When you select this option or if you press , a confirmation window appears. Select Yes to discard changes and exit.

ASUS EZ Mode This option allows you to enter the EZ Mode screen.

Launch EFI Shell from filesystem device This option allows you to attempt to launch the UEFI Shell application (shellx64.efi) from one of the available devices that have a filesystem.

ASUS A55-C A-1

Appendices Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturers instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate this equipment.

IC: Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cut appareil numrique de la Classe B est conforme la norme NMB-003 du Canada. Cet appareil numrique de la Classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Cet appareil est conforme aux normes CNR exemptes de licence dIndustrie Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas provoquer dinterfrences et (2) cet appareil doit accepter toute interfrence, y compris celles susceptibles de provoquer un fonctionnement non souhait de lappareil.

A-2 Appendices

Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003.

VCCI: Japan Compliance Statement

VCCI Class B Statement

KC: Korea Warning Statement

REACH Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm.

DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.

DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

ASUS A55-C A-3

ASUS contact information

ASUSTeK COMPUTER INC. Address 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 Telephone +886-2-2894-3447 Fax +886-2-2890-7798 E-mail info@asus.com.tw Web site www.asus.com.tw

Technical Support Telephone +86-21-38429911 Online support support.asus.com

ASUS COMPUTER INTERNATIONAL (America) Address 800 Corporate Way, Fremont, CA 94539, USA Telephone +1-812-282-3777 Fax +1-510-608-4555 Web site usa.asus.com

Technical Support Telephone +1-812-282-2787 Support fax +1-812-284-0883 Online support support.asus.com

ASUS COMPUTER GmbH (Germany and Austria) Address Harkort Str. 21-23, D-40880 Ratingen, Germany Fax +49-2102-959911 Web site www.asus.de Online contact www.asus.de/sales

Technical Support Telephone +49-1805-010923* Support Fax +49-2102-9599-11 Online support support.asus.com

* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile phone.

Manufacturer: ASUSTeK Computer Inc. Address: 4F, No. 150, LI-TE RD., PEITOU, TAIPEI 112,

TAIWAN R.O.C. Authorised representative in Europe:

ASUS Computer GmbH

Address: HARKORT STR. 21-23, 40880 RATINGEN, GERMANY

A-4 Appendices

EC D

ec la

ra tio

n of

C on

fo rm

ity

W e,

th e

un de

rs ig

ne d,

M

an uf

ac tu

re r:

A

S U

S Te

K C

O M

P U

TE R

IN C

. A

dd re

ss , C

ity :

4F , N

o. 1

50 , L

I-T E

R d.

, P E

IT O

U , T

A IP

E I 1

12 , T

A IW

A N

C

ou nt

ry :

TA IW

A N

A

ut ho

riz ed

re pr

es en

ta tiv

e in

E ur

op e:

A

S U

S C

O M

P U

TE R

G m

bH

A dd

re ss

, C ity

: H

A R

K O

R T

S TR

. 2 1-

23 , 4

08 80

R A

TI N

G E

N C

ou nt

ry :

G E

R M

A N

Y

de cl

ar e

th e

fo llo

w in

g ap

pa ra

tu s:

Pr

od uc

t n am

e :

M ot

he rb

oa rd

M od

el n

am e

: A

55 -C

co nf

or m

w ith

th e

es se

nt ia

l r eq

ui re

m en

ts o

f t he

fo llo

w in

g di

re ct

iv es

:

20 04

/1 08

/E C

-E M

C D

ire ct

iv e

E N

5 50

22 :2

01 0

E N

6 10

00 -3

-2 :2

00 6+

A2 :2

00 9

E N

5 50

13 :2

00 1+

A1 :2

00 3+

A 2:

20 06

E N

5 50

24 :2

01 0

E N

6 10

00 -3

-3 :2

00 8

E N

5 50

20 :2

00 7+

A1 1:

20 11

19 99

/5 /E

C -R

& TT

E D

ire ct

iv e

E N

3 00

3 28

V 1.

7. 1(

20 06

-1 0)

E

N 3

00 4

40 -1

V 1.

6. 1(

20 10

-0 8)

E

N 3

00 4

40 -2

V 1.

4. 1(

20 10

-0 8)

E

N 3

01 5

11 V

9. 0.

2( 20

03 -0

3)

E N

3 01

9 08

-1 V

5. 2.

1( 20

11 -0

5)

E N

3 01

9 08

-2 V

5. 2.

1( 20

11 -0

7)

E N

3 01

8 93

V 1.

6. 1(

20 11

-1 1)

E

N 3

02 5

44 -2

V 1.

1. 1(

20 09

-0 1)

E

N 3

02 6

23 V

1. 1.

1( 20

09 -0

1)

E N

3 00

3 30

-1 V

1. 7.

1( 20

10 -0

2)

E N

3 00

3 30

-2 V

1. 5.

1( 20

10 -0

2)

E N

5 03

60 :2

00 1

E N

6 24

79 :2

01 0

E N

3 01

4 89

-1 V

1. 9.

2( 20

11 -0

9)

E N

3 01

4 89

-3 V

1. 4.

1( 20

02 -0

8)

E N

3 01

4 89

-4 V

1. 4.

1( 20

09 -0

5)

E N

3 01

4 89

-7 V

1. 3.

1( 20

05 -1

1)

E N

3 01

4 89

-9 V

1. 4.

1( 20

07 -1

1)

E N

3 01

4 89

-1 7

V2 .1

.1 (2

00 9-

05 )

E N

3 01

4 89

-2 4

V1 .5

.1 (2

01 0-

09 )

E N

3 02

3 26

-2 V

1. 2.

2( 20

07 -0

6)

E N

3 02

3 26

-3 V

1. 3.

1( 20

07 -0

9)

E N

3 01

3 57

-2 V

1. 4.

1( 20

08 -1

1)

E N

5 03

85 :2

00 2

E N

6 23

11 :2

00 8

20 06

/9 5/

EC -L

VD D

ire ct

iv e

E N

6 09

50 -1

/ A1

1: 20

09

EN 6

09 50

-1 /

A1 2:

20 11

E N

6 00

65 :2

00 2

/ A 2:

20 10

E N

6 00

65 :2

00 2

/ A 12

:2 01

1

20 09

/1 25

/E C

-E rP

D ire

ct iv

e

R eg

ul at

io n

(E C

) N o.

1 27

5/ 20

08

R eg

ul at

io n

(E C

) N o.

6 42

/2 00

9

R eg

ul at

io n

(E C

) N o.

2 78

/2 00

9

20 11

/6 5/

EU -R

oH S

D ire

ct iv

e

V

er . 1

21 00

1

C E

m ar

ki ng

D ec

la ra

tio n

D at

e: J

an . 1

1, 2

01 3

Ye ar

to b

eg in

a ffi

xi ng

C E

m ar

ki ng

:2 01

3

P os

iti on

: C

EO N

am e

: Je

rr y

S he

n

S ig

na tu

re :

__ __

__ __

__

(E C

c on

fo rm

ity m

ar ki

ng )

D E

C L

A R

A T

IO N

O F

C O

N FO

R M

IT Y

Pe r F

C C

P ar

t 2 S

ec tio

n 2.

1 07

7( a)

R

es po

ns ib

le P

ar ty

N am

e:

A su

s C om

pu te

r In

te rn

at io

na l

A

dd re

ss :

80 0

C or

po ra

te W

ay , F

re m

on t,

C A

9 45

39 .

Ph

on e/

Fa x

N o:

(5

10 )7

39 -3

77 7/

(5 10

)6 08

-4 55

5

he re

by d

ec la

re s t

ha t t

he p

ro du

ct

Pr od

uc t N

am e

: M ot

he rb

oa rd

M od

el N

um be

r : A

55 -C

C on

fo rm

s t o

th e

fo llo

w in

g sp

ec ifi

ca tio

ns :

FC C

Pa rt

15 , S

ub pa

rt B,

U ni

nt en

tio na

l R ad

ia to

rs

Su pp

le m

en ta

ry In

fo rm

at io

n:

Th is

de vi

ce c

om pl

ie s

w ith

p ar

t 1 5

of th

e FC

C Ru

le s.

O pe

ra tio

n is

su bj

ec t t

o th

e fo

llo w

in g

tw o

co nd

iti on

s: (1

) Th

is de

vi ce

m ay

n ot

c au

se h

ar m

fu l

in te

rfe re

nc e,

a nd

( 2)

t hi

s de

vi ce

m us

t ac

ce pt

a ny

i nt

er fe

re nc

e re

ce iv

ed ,

in cl

ud in

g in

te rfe

re nc

e th

at m

ay c

au se

u nd

es ire

d op

er at

io n.

R

ep re

se nt

at iv

e Pe

rs on

s N

am e

:

St ev

e C

ha ng

/ Pr

es id

en t

Si gn

at ur

e :

D

at e

:

Ja

n. 1

1, 2

01 3

Manualsnet FAQs

If you want to find out how the A55-C ASUS works, you can view and download the ASUS A55-C Motherboard User Manual on the Manualsnet website.

Yes, we have the User Manual for ASUS A55-C as well as other ASUS manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a ASUS A55-C. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the ASUS A55-C Motherboard User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This ASUS A55-C Motherboard User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download ASUS A55-C Motherboard User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print ASUS A55-C Motherboard User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the ASUS A55-C Motherboard User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.