Contents

ASUS EBS-I10 Computer User Manual PDF

1 of 59
1 of 59

Summary of Content for ASUS EBS-I10 Computer User Manual PDF

EBS-I10 Embedded Computer

User Manual

COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (ASUS).

ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Copyright 2022 ASUSTeK COMPUTER INC. All Rights Reserved.

LIMITATION OF LIABILITY Circumstances may arise where because of a default on ASUS part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the listed contract price of each product.

ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement.

This limit also applies to ASUS suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.

UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.

SERVICE AND SUPPORT Visit our multi-language web site at https://www.asus.com/support/.

First Edition September 2022

E20874

EBS-I10 3

Contents About this manual .............................................................................................................5

Conventions used in this manual ......................................................................................... 6 Typography .................................................................................................................................. 6

Package contents ..............................................................................................................7

Chapter 1: Getting to know your Embedded computer 1.1 Features ......................................................................................................................10

1.1.1 Front view ....................................................................................................................... 10 1.1.2 Rear view ......................................................................................................................... 11

Chapter 2: Using your Embedded computer 2.1 Getting started .........................................................................................................16

2.1.1 Connect the power conenctor to your Embedded computer ..................... 16 2.1.2 Connect a display panel to your Embedded computer ................................. 17 2.1.4 Connect the USB cable from keyboard or mouse ............................................ 18

2.2 Turning your Embedded computer off ...........................................................19

Chapter 3: BIOS Setup 3.1 BIOS setup program ...............................................................................................22

3.1.1 BIOS menu screen ........................................................................................................ 22 3.1.2 Menu bar ......................................................................................................................... 22

3.2 Main menu .................................................................................................................23 3.2.1 System Date [Day MM/DD/YYYY] .......................................................................... 23 3.2.2 System Time [HH:MM:SS] .......................................................................................... 23

3.3 Advanced menu ......................................................................................................23 3.3.1 LVDS Configuration ..................................................................................................... 23 3.3.2 PCH-FW Configuration ............................................................................................... 25 3.3.3 Trusted Computing ..................................................................................................... 25 3.3.4 CPU Configuration ....................................................................................................... 26 3.3.5 Graphics Configuration .............................................................................................. 27 3.3.6 PCI Express Configuration ......................................................................................... 28 3.3.7 CSM Configuration ...................................................................................................... 29 3.3.8 Supper IO Configuration ........................................................................................... 29

4 EBS-I10

3.3.9 Serial Console Redirection ........................................................................................ 30 3.3.10 SATA Configuration ..................................................................................................... 32 3.3.11 USB Configuration ....................................................................................................... 33 3.3.12 Onboard Devices Configuration ............................................................................. 34 3.3.13 NVMe Configuration ................................................................................................... 35 3.3.14 APM Configuration ...................................................................................................... 36 3.3.15 EZ-Flash ............................................................................................................................ 36 3.3.16 Watchdog Timer ........................................................................................................... 36 3.3.17 Miscellaneous ................................................................................................................ 37 3.3.18 Network Stack Configuration .................................................................................. 37

3.4 Hardware Monitor menu ......................................................................................38 3.5 Security menu ..........................................................................................................39

3.5.1 Administrator Password............................................................................................. 39 3.5.2 User Password ............................................................................................................... 40 3.5.3 Secure Boot .................................................................................................................... 40

3.6 Boot menu .................................................................................................................41 3.7 Exit menu ...................................................................................................................42

Appendix Safety information .............................................................................................................44

Setting up your system ............................................................................................................ 44 Care during use ........................................................................................................................... 45

Regulatory notices ............................................................................................................47 Service and Support .........................................................................................................58

EBS-I10 5

About this manual This manual provides information about the hardware and software features of your Embedded computer, organized through the following chapters:

Chapter 1: Getting to know your Embedded computer This chapter details the hardware components of your Embedded computer.

Chapter 2: Using your Embedded computer This chapter provides you with information on using your Embedded computer.

Chapter 3: BIOS Setup This chapter provides a detailed guide to navigating and setting up the BIOS.

Appendix This section includes notices and safety statements your Embedded computer.

6 EBS-I10

Conventions used in this manual To highlight key information in this manual, some text are presented as follows:

IMPORTANT! This message contains vital information that must be followed to complete a task.

NOTE: This message contains additional information and tips that can help complete tasks.

WARNING! This message contains important information that must be followed to keep you safe while performing certain tasks and prevent damage to your Embedded computer's data and components.

Typography

Bold text Indicates a menu or an item to select.

Italic This indicates sections that you can refer to in this manual.

EBS-I10 7

Package contents Your Embedded computer package contains the following items:

EBS-I10

Accessory package

Chassis bracket and screw pack x1

AC power cord x 1

Wi-Fi antenna x 1 (Wi-Fi SKU only)

NOTE: Some bundled accessories may vary with different models. The device illustration is for reference only. Actual product specifications may

vary with models. If the device or its components fail or malfunction during normal and proper

use within the warranty period, bring the warranty card to the ASUS Service Center for replacement of the defective components.

8 EBS-I10

1 Getting to know your Embedded computer

10 EBS-I10

1.1 Features 1.1.1 Front view

Power button

The power button allows you to turn the Embedded Computer on or off. You can use the power button to put your Embedded Computer to sleep mode or press it for four (4) seconds to force shutdown your Embedded Computer.

Microphone port

This port connects to a microphone.

NOTE: This port is not available in GPU SKU.

Headphone port

This port connects to a microphone.

NOTE: This port is not available in GPU SKU.

USB 2.0 ports

These Universal Serial Bus 2.0 ports connect to USB 2.0 devices such as a mouse, printer, scanner, camera, PDA, and others.

EBS-I10 11

1.1.2 Rear view

Power connector

Plug the power cord to this connector.

RATING: 115/230Vac, 50/60Hz, 6A/3A (WW) 115Vac, 60Hz, 6A 220Vac, 50Hz, 3A (China)

Antenna holes

The antenna hole allows you to connect a wireless antenna to enhance wireless signal reception.

NOTE: The Wi-Fi antenna is optional and may not come with the product.

Serial (COM) connector

The 9-pin RS232/422/485 serial (COM) connector allows you to connect devices that have serial ports such as bar code scanner, modem, or printers.

12 EBS-I10

HDMI port

The HDMI (High Definition Multimedia Interface) port supports a Full-HD device such as an LCD TV or monitor to allow viewing on a larger external display.

DisplayPorts

These ports are for DisplayPort-compatible devices

LAN ports

The 8-pin RJ-45 LAN port supports a standard Ethernet cable for connection to a local network.

1 2 3 4 5

6 7 8 9

Pin RS-232 RS-422 RS485

1 NA TX- D-

2 RXD TX+ D

3 TXD RX+ NA

4 NA RX- NA

5 GND GND GND

6 NA NA NA

7 RTS NA NA

8 CTS NA NA

9 NA NA NA

Activity Link LED

Status Description

Off No link

Orange Linked

Blinking Data activity

Speed LED

Status Description

Off 10 Mbps connection

Orange 100 Mbps connection

Green 1 Gbps connection

ACT/LINK LED SPEED LED

LAN port

EBS-I10 13

USB 3.2 Gen 1 port

The USB 3.2 Gen 1 (Universal Serial Bus) port provides a transfer rate up to 5 Gbit/s and a maximum of 5V/0.9A output per port.

Microphone port

This port connects to a microphone.

Headphone port

This port connects to a microphone.

Expansion slot bracket

Remove the expansion slot bracket when installing an expansion card.

14 EBS-I10

2 Using your Embedded computer

16 EBS-I10

2.1 Getting started

2.1.1 Connect the power conenctor to your Embedded computer

To connect the power adapter to your Embedded Computer:

A. Connect the power cord to the power connector of the Embedded Computer.

B. Plug the power connector into a 100 V~240 V power source.

IMPORTANT! We strongly recommend that you use a grounded wall socket while using

your Embedded computer. The socket outlet must be easily accessible and near your Embedded

computer. To disconnect your Embedded computer from its main power supply, unplug

your Embedded computer from the power socket.

EBS-I10 17

2.1.2 Connect a display panel to your Embedded computer

You can connect a display panel or projector to your Embedded computer that has the following connectors:

To connect a display panel to your Embedded computer:

Connect one end of an HDMI cable to an external display, and the other end of the cable to your Embedded computers HDMI port.

HDMI connector

DisplayPort connector Connect one end of an DisplayPort cable to an external display, and the other end of the cable to your Embedded computers HDMI port.

18 EBS-I10

2.1.3 Connect the USB cable from keyboard or mouse

You can connect generally any USB keyboard and mouse to your Embedded computer. You can also connect a USB dongle for a wireless keyboard and mouse set.

To connect a keyboard and mouse to your Embedded computer: Connect the USB cable from your keyboard and mouse to any of the USB ports of your Embedded computer.

NOTE: The keyboard varies with country or region. The keyboard and mouse are purchased separately.

EBS-I10 19

2.2 Turning your Embedded computer off

If your Embedded computer is unresponsive, disconnect the power from the Embedded computer to turn it off.

20 EBS-I10

3 BIOS Setup

22 EBS-I10

3.1 BIOS setup program Use the BIOS Setup program to configure its parameters. The BIOS screens include navigation keys and brief online help to guide you in using the BIOS Setup program.

Entering BIOS Setup at startup To enter BIOS Setup at startup: Press or during the Power-On Self Test (POST). If you do not press or , POST continues with its routines.

Entering BIOS Setup after POST To enter BIOS Setup after POST: Press ++ simultaneously. Press the reset button on the system chassis. Press the power button to turn the system off then back on. Do this

option only if you failed to enter BIOS Setup using the first two options.

WARNING! Using the power button, reset button, or the + + keys to reboot a running operating system can cause damage to your data or system. Always shut down the system properly from the operating system.

IMPORTANT: Visit the ASUS website at www.asus.com to download the latest BIOS file for

this motherboard. The default BIOS settings for this motherboard apply to most working

conditions and ensures optimal performance. If the system becomes unstable after changing any BIOS settings, load the default settings to regain system stability. Select the option Restore Defaults under the Exit Menu or press hotkey F3.

The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.

3.1.1 BIOS menu screen

3.1.2 Menu bar The menu bar on top of the screen has the following main items:

Main For changing the basic system configuration.

EBS-I10 23

Advanced For changing the advanced system settings.

Hardware Monitor

For displaying the system temperature, power status, and changing the fan settings

Security For configuring the system security settings.

Boot For changing the system boot configurations.

Exit For selecting the save options and default settings.

To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted.

3.2 Main menu The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings.

3.2.1 System Date [Day MM/DD/YYYY] Allows you to set the system date.

3.2.2 System Time [HH:MM:SS] Allows you to set the system time.

3.3 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices.

WARNING! Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.

3.3.1 LVDS Configuration Switch to LVDS Configuration options: [Disable] [Enable]

NOTE: The following item appears when you set Switch to LVDS to [Enable].

24 EBS-I10

All-in-One Chassis Allows you to select All-in-One (AiO) Chassis (if applicable) for simplified AiO configuration. Configuration options: [None] [1920*1080 LVDS1] [1920*1080 LVDS2] [1920*1080 LVDS3] [1600*900 LVDS4]

NOTES: Be cautious when selecting AiO chassis. Incorrect selection of AiO chassis can cause

incorrect operation or potential damage to AiO chassis hardware. The following items appear only when you set All-in-One Chassis to [None].

EDID Data Source Configuration options: [Pre-Defined] [Flat Panel Display]

NOTE: The following item appears when you set EDID Data Source to [Pre- Defined].

LFP Panel Type Allows you to select LFP panel used by Internal Graphics Device. Configuration options: [VBIOS Default] [640x480] [800x600] [1024x768] [1280x1024] [1400x1050 LVDS1] [1400x1050 LVDS2] [1600x1200] [1366x768] [1680x1050] [1920x1200] [1440x900] [1600x900] [1024x768] [1280x800] [1920x1080] [2048x1536]

Inverter Polarity Configuration options: [Normal] [Inverted]

Channel Select Configuration options: [Dual Channel] [Single Channel]

Mode Select Confuguration options: [JEIDA] [VESA 6bit] [VESA 8bit] [VESA 10bit]

DIGON enable to LVDS_ON enable(T2)

Configuration options: [0] ~[50]

LVDS_ON enable to BLON enable (T3)

Configuration options: [0] ~[1023]

BLON disable to LVDS_ON disable (T4)

Configuration options: [0] ~[1023]

EBS-I10 25

LVDS_ON disable to DIGON disbale (T5)

Configuration options: [0] ~[50]

Completion of power down to power up (T7)

Configuration options: [0] ~[1023]

VARY_BL enable to BL_EN enable (T9)

Configuration options: [0] ~[1023]

BL_EN disable to VARY_BL disable (T10)

Configuration options: [0] ~[1023]

3.3.2 PCH-FW Configuration This item allows you to configure Management Engine Technology parameters. TPM Device Selection Allows you to select TPM device.

[PTT] Enables PTT in SkuMgr.

[dTPM] Disables PTT in SkuMgr.

NOTE: When PTT is disabled, all data saved on it will be lost.

3.3.3 Trusted Computing Security Device Support Allows you to enable or disable BIOS support for security device. Configuration options: [Disable] [Enable]

NOTE: The following items appear when a TPM device is installed on your motherboard.

SHA1 PCR Bank Configuration options: [Disabled] [Enabled]

SHA256 PCR Bank Configuration options: [Disabled] [Enabled]

26 EBS-I10

Pending operation Allows you to schedule an operation for security device. Configuration options: [None] [TPM Clear]

NOTE: Your computer will reboot during restart in order to change the state of security device.

Platform Hierarchy Configuration options: [Disabled] [Enabled]

Storage Hierarchy Configuration options: [Disabled] [Enabled]

Endorsement Hierarchy Configuration options: [Disabled] [Enabled]

TPM 2.0 UEFI Spec Version Configuration options: [TCG_2] [TCG_1_2]

Physical Presence Spec Version Allows you to select to tell O.S. to support PPI Spec Version 1.2 or 1.3. Configuration options: [1.2] [1.3]

NOTE: Some HCK tests might not support 1.3.

3.3.4 CPU Configuration The items in this menu show CPU-related information the BIOS automatically detects. Intel (VMX) Virtualization Technology This item, when set to [enabled], will allow a VMM to utilize the additional hardware capacities provided by Vanderpool Technology. Configuration options: [Disabled] [Enabled]

Intel Trusted Execution Technology Configuration options: [Disabled] [Enabled]

VT-d Configuration options: [Disabled] [Enabled]

EBS-I10 27

CPU - Power Management Control

This item allows you to manage and configure the CPUs power.

Intel SpeedStepTM Allows your system to support more than two frequency ranges. Configuration options: [Disabled] [Enabled]

Intel Speed Shift Technology Allows you to enable or disable Intel Speed Shift Technology support. When enabled, CPPC v2 interface allows hardware controlled P-state. Configuration options: [Disabled] [Enabled]

NOTE: The following item appears only when Intel SpeedStep or Intel Speed Shift is available and enabled.

Turbo Mode Configuration options: [Disabled] [Enabled]

C states Allows you to enable or disable CPU Power Management. Configuration options: [Disabled] [Enabled]

NOTE: The following item appears only when you set C states to [Enabled].

Enhanced C-states Allows you to enable or disable C1E. CPU will switch to minimum speed when all cores enter C-state. Configuration options: [Disabled]

[Enabled]

3.3.5 Graphics Configuration This item allows you to select a primary display from IGFX and PEG graphical devices.

Primary Display Allows you to select which of the IGFX/PEG/PCI Graphics devices should be the primary display or select SG for switchable Gfx. Configuration options: [Auto] [IGFX] [PEG]

28 EBS-I10

Internal Graphics Configuration options: [Auto] [Disabled] [Enabled]

[Auto] Keeps IGFX enabled base on the setup options.

[Disabled] Disables internal graphics.

[Enabled] Enables internal graphics.

RC6 (Render Standby)

Allows you to enable or disable render standby support. Configuration options: [Disabled] [Enabled]

3.3.6 PCI Express Configuration This item allows you to configure PCI Express settings.

PCIEX16 Slot Allows you to configure the PCI Express Root Port settings.

Enable Root Port Allows you to enable or disable the Root Port. Configuration options: [Disabled] [Enabled]

Max Link Speed Configuration options: [Auto] [Gen1] [Gen2] [Gen3]

Max Link Width Configuration options: [Auto] [Force x1] [Force x2] [Force x4] [Force x8]

ASPM Allows you to set the ASPM Level. Configuration options: [Disabled] [Auto] [ASPM L0s] [ASPM L1] [ASPM L0sL1]

Detect Non-Compliance Device Configuration options: [Disabled] [Enabled]

EBS-I10 29

3.3.7 CSM Configuration CSM Support The item allows you to enable or disable CSM Support.

3.3.8 Supper IO Configuration NCT6116D Super IO Configuration

Serial Port 1 Configuration This item allows you to set parameters of Serial Port 1 (COMA).

Serial Port Allows you to enable or disable the serial port (COM). Configuration options: [Disabled] [Enabled]

COM1 Control Allows you to select COM1 mode. Configuration options: [RS232] [RS422] [RS485]

Serial Port 2 Configuration This item allows you to set parameters of Serial Port 2 (COMB).

Serial Port Allows you to enable or disable the serial port (COM). Configuration options: [Disabled] [Enabled]

COM2 Control Allows you to select COM2 mode. Configuration options: [RS232] [RS422] [RS485]

Serial Port 3 Configuration This item allows you to set parameters of Serial Port 3 (COMC).

Serial Port Allows you to enable or disable the serial port (COM).Configuration options: [Disabled] [Enabled]

Serial Port 4 Configuration This item allows you to set parameters of Serial Port 4 (COMD).

30 EBS-I10

Serial Port Allows you to enable or disable the serial port (COM).Configuration options: [Disabled] [Enabled]

Serial Port 5 Configuration This item allows you to set parameters of Serial Port 5 (COME).

Serial Port Allows you to enable or disable the serial port (COM).Configuration options: [Disabled] [Enabled]

Serial Port 6 Configuration This item allows you to set parameters of Serial Port 6 (COMF).

Serial Port Allows you to enable or disable the serial port (COM).Configuration options: [Disabled] [Enabled]

3.3.9 Serial Console Redirection COM1(~6) Console Redirection Allows you enable or disable the console redirection feature. Configuration options: [Enabled] [Disabled]

NOTE: The following item is accessible when you set Console Redirection to [Enabled].

Console Redirection Settings The settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Terminal Type Configuration options: [VT100] [VT100Plus] [VT-UTF8] [ANSI]

[VT100] ASCII char set.

[VT100Plus] Extends VT100 to support color, function keys, etc.

[VT-UTF8] Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.

[ANSI] Extended ASCII char set.

EBS-I10 31

Bits per second Allows you to select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. Configuration options: [9600] [19200] [38400] [57600] [115200]

Data Bits Configuration options: [7] [8]

Parity A parity bit can be sent with the data bits to detect some transmission errors. Configuration options: [None] [Even] [Odd] [Mark] [Space]

[None] Disables parity check.

[Even] Parity bit is 0 if the num of 1s in the data bits is even.

[Odd] Parity bit is 0 if the num of 1s in the data bits is odd.

[Mark] Parity bit is always 1.

[Space] Parity bit is always 0.

NOTE: Mark and Space Parity do not allow for error detection.

Stop Bits Stop bits indicate the end of a serial data packet. The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit. Configuration options: [1] [2]

Flow Control Flow control can prevent data loss from buffer overflow. When sending data, if the receiving buffers are full, a stop signal can be sent to stop the data flow. Once the buffers are empty, a start signal can be sent to re-start the flow. Hardware flow control uses two wires to send start/stop signals. Configuration options: [None] [Hardware RTS/CTS]

VT-UTF8 Combo Key Support Allows you to enable or disable VT-UTF8 Combination Key Support for ANSI/VT100 terminals. Configuration options: [Disabled] [Enabled]

32 EBS-I10

Recorder Mode With this mode enabled only text will be sent. This is to capture Terminal data. Configuration options: [Disabled] [Enabled]

Resolution 100x31 Allows you to enable or disable extended terminal resolution. Configuration options: [Disabled] [Enabled]

Putty KeyPad Allows you to select FunctionKey and KeyPad on Putty. Configuration options: [VT100] [LINUX] [XTERMR6] [SCO] [ESCN]

[VT400]

3.3.10 SATA Configuration This item allows you to configure SATA device options settings.

SATA Controller(s) Allows you to enables or disables the onboard SATA device. Configuration options: [Disabled] [Enabled]

NOTE: The following item appears only when you set SATA Controller(s) to [Enabled].

SATA Mode Selection Allows you to determine how SATA controller(s) operate. Configuration options: [AHCI]

SATA6G_ 1(~2)

Port 1(~2) Allows you to enable or disable SATA Port. Configuration options: [Disabled] [Enabled]

Hot Plug Allows you to designate this port as Hot Pluggable. Configuration options: [Disabled] [Enabled]

EBS-I10 33

M.2

Configuration options: [Disabled] [Enabled]

MSATA_MPCIE Configuration options: [Disabled] [Enabled]

3.3.11 USB Configuration Legacy USB Support [Enabled] Enables the support for USB devices on legacy OS.

[Disabled] USB devices are only available when running BIOS Setup.

[Auto] Allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled.

XHCI Hand-off This item functions as a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. Configuration options: [Enabled] [Disabled]

USB Mass Storage Driver Support Allows you to enable or disable USB Mass Storage Driver Support. Configuration options: [Disabled] [Enabled]

LAN1_U31G1_E1 Allows you to enable or disable USB port. Once set to [Disabled], any USB devices plugged into the connector will not be detected by BIOS or OS. Configuration options: [Disabled] [Enabled]

LAN1_U31G1_E2 Allows you to enable or disable USB port. Once set to [Disabled], any USB devices plugged into the connector will not be detected by BIOS or OS. Configuration options: [Disabled] [Enabled]

LAN2_U31G1_E3

Allows you to enable or disable USB port. Once set to [Disabled], any USB devices plugged into the connector will not be detected by BIOS or OS. Configuration options: [Disabled] [Enabled]

34 EBS-I10

LAN2_U31G1_E4 Allows you to enable or disable USB port. Once set to [Disabled], any USB devices plugged into the connector will not be detected by BIOS or OS. Configuration options: [Disabled] [Enabled]

U31G1_1(~2) Allows you to enable or disable USB port. Once set to [Disabled], any USB devices plugged into the connector will not be detected by BIOS or OS. Configuration options: [Disabled] [Enabled]

USB_5(~8) Allows you to enable or disable USB port. Once set to [Disabled], any USB devices plugged into the connector will not be detected by BIOS or OS. Configuration options: [Disabled] [Enabled]

3.3.12 Onboard Devices Configuration Audio Controller Allows you to control detection of the HD-Audio device. Configuration options: [Enabled] [Disabled]

[Enabled] Enables the HD Audio Device unconditionally.

[Disabled] Disables the HD Audio Device unconditionally.

Intel LAN1 Controller [Enabled] Enables the Intel LAN controller 1.

[Disabled] Disables the controller.

Intel LAN1 PXE OPROM This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the PXE Option ROM of the Intel LAN controller 1. Configuration options: [Disabled] [Enabled]

Intel LAN2 Controller [Enabled] Enables the Intel LAN controller 2.

[Disabled] Disables the controller.

EBS-I10 35

Intel LAN2 PXE OPROM This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the PXE Option ROM of the Intel LAN controller 2. Configuration options: [Disabled] [Enabled]

Wi-Fi Controller [Enabled] Enables the Wi-Fi controller.

[Disabled] Disables the controller.

Bluetooth Controller [Enabled] Enables the Bluetooth controller.

[Disabled] Disables the controller.

M.2 Configuration [Auto] Auto-detects the M.2 device mode.

[SATA Mode] Only supports M.2 SATA devices.

[PCIE Mode] Only supports M.2 PCIE devices.

MSATA_MPCIE Configuration [Auto] Auto-detects the M.2 device mode.

[MSATA Mode] Only supports MSATA devices.

[MPCIE Mode] Only supports MPCIE devices.

3.3.13 NVMe Configuration The NVMe Configuration menu displays the NVMe controller and drive information of the devices connected and allows you to configure NVMe device options settings.

3.3.14 APM Configuration ErP Ready Allows BIOS to switch off some power at S5 to get the system ready for ErP requirement. When set to [Enabled], all other PME options will be switched off. Configuration options: [Enable] [Disabled]

36 EBS-I10

Restore AC Power Loss Allows you to select AC power state when power is re-applied after a power failure. Configuration options: [S5 State] [S0 State]

Power On By PCIE Allows you to enable or disable the Wake-on-LAN function of the onboard LAN controller or other installed PCIe LAN cards. Configuration options: [Disabled] [Enabled]

Power On By RTC Allows you to enable or disable the RTC (Real-Time Clock) to generate a wake event and configure the RTC alarm date. When enabled, you can set the days, hours, minutes, or seconds to schedule an RTC alarm date. Configuration options: [Disabled] [Single event] [Daily event] [Weekly event]

[Monthly event]

3.3.15 EZ-Flash This item allows you to enter EZ-Flash mode. After you press , a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press to confirm your choice.

3.3.16 Watchdog Timer Watchdog Support Configuration options: [Disabled] [Enabled]

NOTE: The following items appear when you set Watchdog Support to [Enable].

Watchdog Count mode Allows you to select Watchdog Timer I count mode. Configuration options: [Second Mode] [Minute Mode]

Watchdog Timer Allows you to set the Watchdog Timer I Time-out value.

EBS-I10 37

3.3.17 Miscellaneous DMI/OPI Configuration

PCI Express Configuration

DMI Link ASPM Control Allows you to disable or control Active State Power Management on SA side of the DMI link. Configuration options: [Disabled] [L0s] [L1]

[L0sL1][Auto]

3.3.18 Network Stack Configuration Network Stack This item allows user to disable or enable the UEFI network stack. Configuration options: [Disabled] [Enabled]

NOTE: The following two items appear only when you set the previous item to [Enabled].

Ipv4 PXE Support This item allows user to disable or enable the Ipv4 PXE Boot support. Configuration options: [Disabled] [Enabled]

Ipv6 PXE Support This item allows user to disable or enable the Ipv6 PXE Boot support. Configuration options: [Disabled] [Enabled]

3.4 Hardware Monitor menu The Hardware Monitor menu displays the system temperature/power status, and allows you to change the fan settings.

CPU / MotherBoard Temperature The onboard hardware monitor automatically detects and displays the CPU/ motherboard temperatures.

38 EBS-I10

CPU / Chassis Fan Speed The onboard hardware monitor automatically detects and displays the CPU / chassis fan speeds in rotations per minute (RPM). If the fan is not connected to the motherboard, the field shows N/A. Select Ignore if you do not wish to display the detected speed.

CPU Core Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. Select Ignore if you do not want to detect this item.

Smart Fan Mode

Allows you to select the Smart Fan mode. Configuration options: [Disabled] [Normal] [Manual Mode]

NOTE: The following items appear when you set Smart Fan Mode to [Manual Mode].

Chassis Fan Setting

Temperature 1(~4) Allows you to set the value of temperature1(~4).

FD/RPM 1(~4) Allows you to set the value of Fan Duty/PRM 1(~4) when temperature is T1(~4).

CPU Fan Setting

Temperature 1(~4) Allows you to set the value of temperature1(~4).

FD/RPM 1(~4) Allows you to set the value of Fan Duty/PRM 1(~4) when temperature is T1(~4).

EBS-I10 39

3.5 Security menu The Security menu allows a new password to be created or a current password to be changed. The menu also enables or disables the Secure Boot state and lets the user configure the System Mode state.

3.5.1 Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system.

To set an administrator password:

1. Select the Administrator Password item and press .

2. From the Create New Password box, key in a password, then press .

To change an administrator password:

1. Select the Administrator Password item and press .

2. From the Enter Current Password box, key in the current password, then press .

3. From the Create New Password box, key in a new password, then press .

4. Confirm the password when prompted.

NOTE: To clear the administrator password, follow the same steps as in changing an administrator password, but press when prompted to create/confirm the password.

3.5.2 User Password If you have set a user password, you must enter the user password for accessing the system.

To set a user password:

1. Select the User Password item and press .

40 EBS-I10

2. From the Create New Password box, key in a password, then press .

3. Confirm the password when prompted.

To change a user password:

1. Select the User Password item and press .

2. From the Enter Current Password box, key in the current password, then press .

3. From the Create New Password box, key in a new password, then press .

4. Confirm the password when prompted.

3.5.3 Secure Boot Secure Boot feature is active when Secure Boot is set to [Enabled], Platform Key (PK) is enrolled and the system is running in User mode. Changing the mode requires platform reset. Configuration options: [Disabled] [Enabled]

Secure Boot Mode Allows you to select Secure Boot Mode. When set to [Custom], Secure Boot Policy variables can be configured by a physically present user without full authentication. Configuration options: [Standard] [Custom]

Key Management Allows you to modify Secure Boot Policy variables without full authentication.

Platform Key (PK) Configuration options: [Update]

Key Exchange Keys / Authorized Signatures Configuration options: [Update] [Append]

Forbidden Signatures Configuration options: [Details] [Export][Update] [Append] [Delete]

EBS-I10 41

3.6 Boot menu The Boot menu items allow you to change the system boot options.

Boot Configuration

Setup Prompt Timeout Allows you to set the number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.

Bootup NumLock State Allows you to select the keyboard NumLock state. Configuration options: [On] [Off]

Quiet Boot Configuration options: [Disabled] [Enabled]

Fast Boot Allows you to enable or disable boot with initialization of a minimal set of devices required to launch active boot option. This has no effect for BBS boot options. Configuration options: [Disabled] [Enabled]

Boot mode select Configuration options: [UEFI] [LEGACY]

FIXED BOOT ORDER Priorities

Boot Option #1(~5) Allows you to set the system boot order. Configuration options: [Hard Disk] [NVME] [CD/DVD] [USB Device] [Network] [Disabled]

42 EBS-I10

3.7 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit menu.

Save Changes and Exit Allows you to exit the system setup program after saving the changes.

Discard Changes and Exit Allows you to exit the system setup program without saving the changes you made. When you select this option or if you press , a confirmation window appears. Select Yes to discard changes and exit.

Save Changes and Reset Allows you to reset the system setup after saving the changes.

Discard Changes and Reset Allows you to reset the system setup without saving the changes you made.

Save Options

Save Changes Allows you to save changes done so far to any of the setup options.

Discard Changes Allows you to discard changes done so far to any of the setup options.

Restore Defaults Allows you to restore or load default values for all the setup options.

Save as User Defaults Allows you to save the changes done so far as User Defaults.

Restore User Defaults Allows you to restore the User Defaults to all the setup options.

Appendix

44 EBS-I10

Safety information Your Embedded computer is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions.

Setting up your system Read and follow all instructions in the documentation before you

operate your system. Do not use this product near water or a heated source. Set up the system on a stable surface. Peripherals with extended temperature tolerance will allow this product

to be used in environments with ambient temperatures between -20C and 60C.

The product should be used in environments with an ambient temperature of 35C when using the 65W adapter.

If you use an extension cord, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating.

For your safety, only connect this device to a properly grounded electrical outlet.

This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Restricted Access Location: The equipment should only be installed in a Restricted Access Area

where both these conditions apply: - access can only be gained by USERS who have been instructed about

the reasons for the restrictions applied to the location and about any precautions that shall be taken; and

- access is through the use of a TOOL or lock and key, or other means of security, and is controlled by the authority responsible for the location.

This device shall not be connected to an Ethernet network with outside plant routing.

EBS-I10 45

Care during use Do not walk on the power cord or allow anything to rest on it.

Do not spill water or any other liquids on your system. When the system is turned off, a small amount of electrical current still

flows. Always unplug the power cord from the power outlets before cleaning the system.

Please use this product with care when operating this product at full load, as the product may reach temperatures of up to 60C and the outer casing may reach temperatures of up to 72C

If you encounter the following technical problems with the product, unplug the power cord and contact a qualified service technician or your retailer.

The power cord or plug is damaged. Liquid has been spilled into the system. The system does not function properly even if you follow

the operating instructions. The system was dropped or the cabinet is damaged. The system performance changes.

NO DISASSEMBLY The warranty does not apply to the products

that have been disassembled by users

Lithium-Ion Battery Warning CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions.

46 EBS-I10

DO NOT throw the Embedded computer in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment, and mercury-containing button cell battery) should not be placed in municipal waste. Check local technical support services for product recycling.

EBS-I10 47

Regulatory notices COATING NOTICE

IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the device except on the areas where the I/O ports are located.

Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received including

interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT! Outdoor operations in the 5.15~5.25 GHz band is prohibited. This device has no Ad-hoc capability for 5250~5350 and 5470~5725 MHz.

WARNING! Any changes or modifications not expressly approved by the grantee of this device could void the users authority to operate the equipment.

48 EBS-I10

RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following:

Contains FCC ID: TX2-RTL8822CE and Contains IC:6317A-RTL8822CE

ISED Radiation Exposure Statement for Canada This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with ISED RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. End users must follow the specific operating instructions for satisfying RF exposure compliance.

Operation is subject to the following two conditions:

This device may not cause interference and This device must accept any interference, including interference that

may cause undesired operation of the device.

EBS-I10 49

Wireless Operation Channel for Different Domains N. America 2.412-2.462 GHz Ch01 through CH11

Japan 2.412-2.484 GHz Ch01 through Ch14

Europe ETSI 2.412-2.472 GHz Ch01 through Ch13

Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(A)/NMB-3(A)

Dclaration de conformit de Innovation, Sciences et Dveloppement conomique Canada (ISED) Le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

CAN ICES-3(A)/NMB-3(A)

KC: Korea Warning Statement Class A:

.

50 EBS-I10

VCCI: Japan Compliance Statement

Class A ITE

Japan RF Equipment Statement 5GHz 5.2GHz5.3GHz

Japan JATE LAN

EBS-I10 51

Declaration of compliance for product environmental regulation ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements.

Please refer to http://csr.asus.com/Compliance.htm for information disclosure based on regulation requirements ASUS is complied with:

EU REACH and Article 33 Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm

EU RoHS This product complies with the EU RoHS Directive. For more details, see http://csr.asus.com/english/article.aspx?id=35

Japan JIS-C-0950 Material Declarations Information on Japan RoHS (JIS-C-0950) chemical disclosures is available on http://csr.asus.com/english/article.aspx?id=19

India RoHS This product complies with the India E-Waste (Management) Rules, 2016 and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1% by weight in homogenous materials and 0.01% by weight in homogenous materials for cadmium, except for the exemptions listed in Schedule II of the Rule.

Vietnam RoHS ASUS products sold in Vietnam, on or after September 23, 2011,meet the requirements of the Vietnam Circular 30/2011/TT-BCT.

Cc sn phm ASUS bn ti Vit Nam, vo ngy 23 thng 9 nm2011 tr v sau, u phi p ng cc yu cu ca Thng t 30/2011/TT-BCT ca Vit Nam.

52 EBS-I10

Trkiye RoHS AEEE Ynetmeliine Uygundur

ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http:// csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

Ecodesign Directive European Union announced a framework for the setting of ecodesign requirements for energy-related products (2009/125/EC). Specific Implementing Measures are aimed at improving environmental performance of specific products or across multiple product types. ASUS provides product information on the CSR website. The further information could be found at https://csr.asus.com/english/article.aspx?id=1555.

ENERGY STAR complied product ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy helping us all save money and protect the environment through energy efficient products and practices.

All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR standard, and the power management feature is enabled by default. The monitor is automatically set to sleep within 10 minutes of user inactivity; the computer is automatically set to sleep within 30 minutes of user inactivity. To wake your computer, click the mouse, press any key on the keyboard, or press the power button.

Please visit http://www.energystar.gov/powermanagement for detail information on power management and its benefits to the environment. In addition, please visit http://www.energystar.gov for detail information on the ENERGY STAR joint program.

NOTE: Energy Star is NOT supported on FreeDOS and Linux-based products.

EBS-I10 53

UK: The Radio Equipment Regulations 2017 (S.I. 2017/1206) Simplified UKCA Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of The Radio Equipment Regulations 2017 (S.I. 2017/1206). Full text of UKCA declaration of conformity is available at https://www.asus.com/support/.. The WiFi operating in the band 5150-5350MHz shall be restricted to indoor use for country listed below:

UK UKCA RF Output table (The Radio Equipment Regulations 2017) RTK RTL8822CE

Function Frequency Maximum Output Power (EIRP)

WiFi

2412 - 2472 MHz 19 dBm

5150 - 5250 MHz 19 dBm

5250 - 5350 MHz 19 dBm

5470 - 5725 MHz 20 dBm

Bluetooth 2402 - 2480 MHz 15 dBm

* Receiver category 1

UKCA RF Output table (The Radio Equipment Regulations 2017) Intel AX200NGW

Function Frequency Maximum Output Power (EIRP)

WiFi

2412 - 2472 MHz 19 dBm

5150 - 5250 MHz 19 dBm

5250 - 5350 MHz 19 dBm

5470 - 5725 MHz 19 dBm

5725 - 5850 MHz 9 dBm

Bluetooth 2402 - 2480 MHz 13 dBm

* Receiver category 1

54 EBS-I10

EU: Radio Equipment Directive (Directive 2014/53/EU) Simplified EU Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.com/support/. The WiFi operating in the band 5150-5350MHz shall be restricted to indoor use for countries listed in the table below:

Dclaration simplifie de conformit de lUE ASUSTek Computer Inc. dclare par la prsente que cet appareil est conforme aux critres essentiels et autres clauses pertinentes de la directive 2014/53/EU. La dclaration de conformit de lUE peut tre tlcharge partir du site internet suivant : https://www.asus.com/support/. Dans la plage de frquence 5150-5350 MHz, le Wi-Fi est restreint une utilisation en intrieur dans les pays lists dans le tableau ci-dessous:

Vereinfachte EU-Konformittserklrung ASUSTek COMPUTER INC erklrt hiermit, dass dieses Gert mit den grundlegenden Anforderungen und anderen relevanten Bestimmungen der Richtlinie 2014/53/EU bereinstimmt. Der gesamte Text der EU-Konformittserklrung ist verfgbar unter: https://www.asus.com/support/. Der WLAN-Betrieb im Band von 5150-5350 MHz ist fr die in der unteren Tabelle aufgefhrten Lnder auf den Innenbereich beschrnkt:

Dichiarazione di conformit UE semplificata ASUSTek Computer Inc. con la presente dichiara che questo dispositivo conforme ai requisiti essenziali e alle altre disposizioni pertinenti con la direttiva 2014/53/EU. Il testo completo della dichiarazione di conformit UE disponibile allindirizzo: https://www.asus.com/support/. Lutilizzo della rete Wi-Fi con frequenza compresa nellintervallo 5150-5350MHz deve essere limitato allinterno degli edifici per i paesi presenti nella seguente tabella:

ASUSTek Computer Inc. , 2014/53/EU. https://www.asus.com/support/. WiFi 5150-5350 , :

.2014/53/EU ASUSTek Computer

: .https://www.asus.com/support/

. 5150-5350 WiFi

ASUSTek Computer Inc. , 2014/53/EC. https://www.asus.com/support/. WiFi, 5150-5350MHz, , -:

Declarao de Conformidade UE Simplificada ASUSTek Computer Inc. declara que este dispositivo est em conformidade com os requisitos essenciais e outras disposies relevantes relacionadas s diretivas 2014/53/UE. O texto completo da declarao de conformidade CE est disponvel em https://www.asus.com/support/. O WiFi operando na banda 5150-5350MHz deve ser restrito para uso interno para os pases listados na tabela abaixo:

Pojednostavljena EU Izjava o sukladnosti ASUSTeK Computer Inc. ovim izjavljuje da je ovaj ureaj sukladan s bitnim zahtjevima i ostalim odgovarajuim odredbama direktive 2014/53/EU. Cijeli tekst EU izjave o sukladnosti dostupan je na https://www.asus.com/support/. WiFi koji radi na opsegu frekvencija 5150-5350 MHz bit e ogranien na upotrebu u zatvorenom prostoru u zemljama na donjem popisu:

EBS-I10 55

Zjednoduen prohlen o shod EU Spolenost ASUSTek Computer Inc. tmto prohlauje, e toto zazen spluje zkladn poadavky a dal pslun ustanoven smrnice 2014/53/ EU. Pln znn prohlen o shod EU je k dispozici na adrese https://www.asus.com/support/. V zemch uvedench v tabulce je provoz st Wi-Fi ve frekvennm rozsahu 5 150 - 5 350 MHz povolen pouze ve vnitnch prostorech:

Forenklet EU-overensstemmelseserklring ASUSTeK Computer Inc. erklrer hermed at denne enhed er i overensstemmelse med hovedkravene og vrige relevante bestemmelser i direktivet 2014/53/EU. Hele EU-overensstemmelseserklringen kan findes p https://www.asus.com/support/. Wi-Fi, der bruger 5150-5350 MHz skal begrnses til indendrs brug i lande, der er anfrt i tabellen:

Vereenvoudigd EU-conformiteitsverklaring ASUSTeK Computer Inc. verklaart hierbij dat dit apparaat voldoet aan de essentile vereisten en andere relevante bepalingen van Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring is beschikbaar op https://www.asus.com/support/. De WiFi op 5150-5350MHz zal beperkt zijn tot binnengebruik voor in de tabel vermelde landen:

Lihtsustatud E vastavusdeklaratsioon Kesolevaga kinnitab ASUSTek Computer Inc, et seade vastab direktiivi 2014/53/E olulistele nuetele ja teistele asjakohastele stetele. EL vastavusdeklaratsiooni tistekst on saadaval veebisaidil https://www.asus.com/support/. Sagedusvahemikus 5150-5350 MHz ttava WiFi kasutamine on jrgmistes riikides lubatud ainult siseruumides:

Eurooppa - EY:n vaatimustenmukaisuusvakuutus ASUSTek Computer Inc. ilmoittaa tten, ett tm laite on direktiivin 2014/53/EU olennaisten vaatimusten ja muiden asiaankuuluvien lisysten mukainen. Koko EY:n vaatimustenmukaisuusvakuutuksen teksti on luettavissa osoitteessa https://www.asus.com/support/. 5 150 - 5 350 MHz:in taajuudella toimiva WiFi on rajoitettu siskyttn taulukossa luetelluissa maissa:

. .2014/53/EU ASUSTek Computer Inc

: .https://www.asus.com/support/

. WiFi 5150-5350

ASUSTek Computer Inc. 2014/53/E. https://www.asus.com/support/. WiFi 5150-5350MHz :

2014/53/ ASUSTek Computer Inc.

: .EU .https://www.asus.com/support/

5150-5350MHz Wi-Fi :

Egyszerstett EU megfelelsgi nyilatkozat Az ASUSTek Computer Inc. ezennel kijelenti, hogy ez az eszkz megfelel az 2014/53/EU sz. irnyelv alapvet kvetelmnyeinek s egyb vonatkoz rendelkezseinek. Az EU megfelelsgi nyilatkozat teljes szvegt a kvetkez weboldalon tekintheti meg: https://www.asus.com/support/. Az 5150-5350 MHz-es svban mkd Wi-Fi-t beltri hasznlatra kell korltozni az albbi tblzatban felsorolt orszgokban:

Pernyataan Kesesuaian UE yang Disederhanakan ASUSTeK Computer Inc. dengan ini menyatakan bahwa perangkat ini memenuhi persyaratan utama dan ketentuan relevan lainnya yang terdapat pada Petunjuk 2014/53/EU. Teks lengkap pernyataan kesesuaian EU tersedia di: https://www.asus.com/support/. WiFi yang Beroperasi pada 5150-5350 MHz akan terbatas untuk penggunaan dalam ruangan di negara yang tercantum dalam tabel

56 EBS-I10

Vienkrota ES atbilstbas paziojums ASUSTeK Computer Inc. ar o pazio, ka ierce atbilst Direktvas 2014/53/ES btiskajm prasbm un citiem citiem saistoajiem nosacjumiem. Pilns ES atbilstbas paziojuma teksts pieejams eit: https://www.asus.com/support/. Wi-Fi darbba 51505350 MHz ir jierobeo lietoanai telps valsts, kuras nordtas tlk.

Supaprastinta ES atitikties deklaracija iame dokumente bendrov ASUSTek Computer Inc. pareikia, kad is prietaisas atitinka pagrindinius reikalavimus ir kitas susijusias Direktyvos 2014/53/ES nuostatas. Visas ES atitikties deklaracijos tekstas pateikiamas ia: https://www.asus.com/support/. Toliau nurodytose alyse WiFi ryiu, veikianiu 5 1505 350 MHz danio juostoje, galima naudotis tik patalpose:

Forenklet EU-samsvarserklring ASUSTek Computer Inc. erklrer herved at denne enheten er i samsvar med hovedsaklige krav og andre relevante forskrifter i direktivet 2014/53/EU. Fullstendig tekst for EU-samsvarserklringen finnes p: https://www.asus.com/support/. Wi-Fi-omrdet 51505350 MHz skal begrenses til innendrs bruk for landene som er oppfrt i tabellen:

Uproszczona deklaracja zgodnoci UE Firma ASUSTek Computer Inc. niniejszym owiadcza, e urzdzenie to jest zgodne z zasadniczymi wymogami i innymi waciwymi postanowieniami dyrektywy 2014/53/EU. Peny tekst deklaracji zgodnoci UE jest dostpny pod adresem https://www.asus.com/support/. W krajach wymienionych w tabeli dziaanie sieci Wi-Fi w pamie 51505350 MHz powinno by ograniczone wycznie do pomieszcze:

Declarao de Conformidade Simplificada da UE A ASUSTek Computer Inc. declara que este dispositivo est em conformidade com os requisitos essenciais e outras disposies relevantes da Diretiva 2014/53/UE. O texto integral da declarao de conformidade da UE est disponvel em https://www.asus.com/support/. A utilizao das frequncias WiFi de 5150 a 5350MHz est restrita a ambientes interiores nos pases apresentados na tabela:

Declaraie de conformitate UE, versiune simplificat Prin prezenta, ASUSTek Computer Inc. declar c acest dispozitiv este n conformitate cu reglementrile eseniale i cu celelalte prevederi relevante ale Directivei 2014/53/UE. Textul complet al declaraiei de conformitate UE este disponibil la adresa https://www.asus.com/support/. Pentru rile listate n tabelul de mai jos, reelele WiFi care funcioneaz n banda de frecven de 5.150-5.350 MHz trebuie utilizate doar n interior:

Pojednostavljena Deklaracija o usaglaenosti EU ASUSTek Computer Inc. ovim izjavljuje da je ovaj ureaj usaglaen sa osnovnim zahtevima i drugim relevantnim odredbama Direktive 2014/53/EU. Ceo tekst Deklaracije o usaglaenosti EU dostupan je na lokaciji https://www.asus.com/support/. WiFi koji radi u frekventnom opsegu od 5150 MHz do 5350 MHz ogranien je iskljuivo na upotrebu u zatvorenom prostoru za zemlje navedene u tabeli ispod:

Zjednoduen vyhlsenie o zhode platn pre E Spolonos ASUSTek Computer Inc. tmto vyhlasuje, e toto zariadenie je v slade so zkladnmi poiadavkami a almi prslunmi ustanoveniami smernice . 2014/53/E. Pln znenie vyhlsenia o zhode pre E je k dispozcii na lokalite https://www.asus.com/support/. innos WiFi v psme 5150 - 5350 MHz bude obmedzen na pouitie vo vntornom prostred pre krajiny uveden v tabuke niie:

Poenostavljena izjava EU o skladnosti ASUSTek Computer Inc. tukaj izjavlja, da je ta naprava skladna s temeljnimi zahtevami in drugimi relevantnimii doloili Direktive 2014/53/EU. Polno besedilo izjave EU o skladnosti je na voljo na https://www.asus.com/support/. WiFi, ki deluje v pasovnem obmoju 51505350 MHz, mora biti v dravah, navedenih v spodnjem seznamu, omejen na notranjo uporabo:

Declaracin de conformidad simplificada para la UE Por la presente, ASUSTek Computer Inc. declara que este dispositivo cumple los requisitos bsicos y otras disposiciones pertinentes de la directiva 2014/53/EU. En https://www.asus.com/support/ est disponible el texto completo de la declaracin de conformidad para la UE. La conexin WiFi con una frecuencia de funcionamiento de 5150-5350 MHz se restringir al uso en interiores para los pases enumerados en la tabla:

EBS-I10 57

Frenklad EU-frskran om verensstmmelse ASUSTek Computer Inc. deklarerar hrmed att denna enhet verensstmmer med de grundlggande kraven och andra relevanta bestmmelser i direktiv 2014/53/EU. Fullstndig text av EU-frskran om verensstmmelse finns p https://www.asus.com/support/. WiFi som anvnder 5150-5350 MHz kommer att begrnsas fr anvndning inomhus i de lnder som anges i tabellen:

ASUSTek Computer Inc. 2014/53/EU EU https://www.asus.com/support/. WiFi 5150-5350MHz

Basitletirilmi AB Uyumluluk Bildirimi ASUSTek Computer Inc., bu aygtn 2014/53/EU Ynergesinin temel gereksinimlerine ve dier ilgili hkmlerine uygun olduunu bildirir. AB uygunluk bildiriminin tam metni u adreste bulunabilir: https://www.asus.com/support/. 5150-5350 MHz arasndaki WiFi almas, tabloda listelenen lkeler iin i mekn kullanmyla kstlanacaktr.

ASUSTek Computer Inc. , 2014 / 53 / EU. https://www.asus.com/support/. Wi-Fi 5150-5350 , :

AT BE BG CZ DK EE FR

DE IS IE IT EL ES CY

LV LI LT LU HU MT NL

NO PL PT RO SI SK TR

FI SE CH HR UK(NI)

CE RED RF Output table (Directive 2014/53/EU) RTK RTL8822CE

Function Frequency Maximum Output Power (EIRP)

WiFi

2412 - 2472 MHz 19 dBm

5150 - 5250 MHz 19 dBm

5250 - 5350 MHz 19 dBm

5470 - 5725 MHz 20 dBm

Bluetooth 2402 - 2480 MHz 15 dBm

* Receiver category 1

CE RED RF Output table (Directive 2014/53/EU) Intel AX200NGW

Function Frequency Maximum Output Power (EIRP)

WiFi

2412 - 2472 MHz 19 dBm

5150 - 5250 MHz 19 dBm

5250 - 5350 MHz 19 dBm

5470 - 5725 MHz 19 dBm

5725 - 5850 MHz 9 dBm

Bluetooth 2402 - 2480 MHz 13 dBm

* Receiver category 1

58 EBS-I10

Service and Support Visit our multi-language website at https://www.asus.com/support/.

EBS-I10 59

Manufacturer ASUSTeK Computer Inc.

Tel: +886-2-2894-3447

Address: 1F., No. 15, Lide Rd., Beitou Dist., Taipei City 112

Authorised representative in Europe

ASUSTeK Computer GmbH

Address: Harkortstrasse 21-23, 40880 Ratingen, Germany

Authorized Representative in United Kingdom

ASUSTEK (UK) LIMITED

1st Floor, Sackville House, 143-149 Fenchurch Street, London, EC3M 6BL, England, United Kingd

Manualsnet FAQs

If you want to find out how the EBS-I10 ASUS works, you can view and download the ASUS EBS-I10 Computer User Manual on the Manualsnet website.

Yes, we have the User Manual for ASUS EBS-I10 as well as other ASUS manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Manual should include all the details that are needed to use a ASUS EBS-I10. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the ASUS EBS-I10 Computer User Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This ASUS EBS-I10 Computer User Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download ASUS EBS-I10 Computer User Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print ASUS EBS-I10 Computer User Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the ASUS EBS-I10 Computer User Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.