Contents

Apple iPhone 13 Pro Smartphone Repair Manual PDF

1 of 81
1 of 81

Summary of Content for Apple iPhone 13 Pro Smartphone Repair Manual PDF

2022 Apple Inc. All rights reserved.

Repair Manual iPhone 13 Pro

iPhone 13 Pro

073-00324-A | 2 2022 Apple Inc. All rights reserved.

Contents

3 Introduction

Basics

6 Internal View 7 Orderable Parts 9 Screws 10 Tools

Safety

15 Battery Safety 18 Broken Glass

Procedures

20 First Steps 21 SIM Tray 22 Display 50 Bottom Speaker 55 Camera 62 Taptic Engine 66 Battery

Contents

iPhone 13 Pro

073-00324-A | 3 2022 Apple Inc. All rights reserved.

Introduction

Introduction

This manual includes technical instructions for replacing genuine Apple parts in iPhone and is intended for individual technicians with the knowledge, experience, and tools required to repair electronic devices.

Important Read the entire manual first. If youre not comfortable performing the repairs as instructed in

this manual, dont proceed. Always use the latest version of this document available at support.apple.com/manuals/

repair+manual.

Warning Failure to follow the repair instructions or to use genuine Apple parts or proper tools may

cause fire or other safety issues and lead to personal injury or death. iPhone 7 and later are classified as Class 1 Laser products per IEC 60825-1 Ed. 3.

These devices comply with 21 CFR 1040.10 and 1040.11, except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019. These devices contain one or more lasers. Use other than as described in the user guide, repair, or disassembly may cause damage, which could result in hazardous exposure to infrared laser emissions that are not visible.

Failure to follow the repair instructions or to use genuine Apple parts or proper tools may damage the iPhone, parts, or other property, or compromise the devices functionality or water resistance.

Caution

Warranty information Damage caused by repairs performed outside of Apple or the Apple Authorized Service network is not covered by Apples warranty or AppleCare plans. Such damage may cause future repairs to be subject to out-of-warranty costs or render the device ineligible for future repairs by Apple or Apple Authorized Service Providers.

iPhone 13 Pro

073-00324-A | 4 2022 Apple Inc. All rights reserved.

Introduction

Software tools

A System Configuration step may be required at the end of your repair. System Configuration is a postrepair software tool that completes the repair for genuine Apple parts. Running System Configuration has a number of purposes that vary based on the part replaced.

What System Configuration does Why its important Transfers factory calibration values

Certain parts like displays, cameras, and ambient light sensors have calibration values that are customized to each individual part during manufacturing. Transferring these values ensures maximum performance and quality after a repair.

Links Secure Element and biometric authentication parts

After repair of a logic board or a biometric authentication part (Touch ID or Face ID), linking the biometric sensors to the Secure Enclave on the logic board is required to ensure device security.

Ensures repair integrity

After a hardware repair, software checks are performed to ensure repair integrity. Repair integrity means that a genuine Apple part has been correctly installed.

Assigns wireless region

To comply with regional communications regulations, a wireless region must be assigned to your logic board.

Updates firmware Keeping firmware up to date ensures that the device has all the latest security and performance features.

The heated display removal fixture softens adhesive to allow separation of the display from the enclosure. The fixture is used with a heated display pocket designed for the devices specific dimensions.

The display press applies the appropriate amount of pressure to secure new adhesive during display installation. The display press is used with a repair tray and display adhesive press plate designed for the devices specific dimensions.

The battery press applies the appropriate amount of pressure to secure new adhesive during battery installation. The battery press is used with a repair tray designed for the devices specific dimensions.

Ordering tools and parts

You can learn how to order genuine Apple parts and tools at support.apple.com/self-service-repair. During the purchase process, enter the manual ID RENLTC to indicate that youve read this manual in its entirety and agree that you have the knowledge and experience to perform your intended repair.

Tools and parts Hardware tools

Apple tools are designed to apply the appropriate heat, force, and torque during repairs, and to withstand high-volume professional use.

iPhone 13 Pro

073-00324-A | 5 2022 Apple Inc. All rights reserved.

Introduction

System Configuration requires a strong Wi-Fi network capable of 1.0 Mbps download and upload speeds, with less than 400 ms latency and less than 2% packet loss. Estimated data usage to run System Configuration is 622 MB.

The device must be running the latest version of iOS and not a beta version.

Learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important Supplemental information for successfully completing procedures; neither a Warning nor a Caution

Caution Instructions for reducing risk of data loss or device hardware damage

Alerts

Failure to follow alerts could result in fire, injury, data loss, or damage to the device, parts, or other property.

Warning Instructions for reducing risk of personal injury

iPhone 13 Pro

073-00324-A | 6 2022 Apple Inc. All rights reserved.

Internal View

Internal View

1. Top speaker 2. TrueDepth camera assembly 3. Cameras 4. Camera flex cable 5. Top battery adhesive tab 6. Battery 7. Bottom battery adhesive tabs 8. Bottom speaker 9. Lightning connector 10. Bottom microphones

11. Taptic Engine 12. SIM reader 13. Battery connector 14. Display/Multi-Touch connector 15. Dock flex cable 16. Logic board cowling 17. Logic board 18. Ambient light/proximity sensor connector 19. Grounding strap

iPhone 13 Pro

073-00324-A | 7 2022 Apple Inc. All rights reserved.

Orderable Parts

Name Numbers Screws

Battery 661-21996

Bottom speaker 923-06256 923-06273 (1) lower right 923-06275 (1) upper left 923-06276 (2) lower left, upper right

Camera 661-22293

Camera cowling 923-06290 923-06266 (1) middle 923-06267 (1) upper right 923-06268 (3) left, lower left, lower right

Display 661-21993 LL661-21993 (U.S.)

Display adhesive 923-06628

Lower cowling 923-06289 923-06265 (3)

Rubber gasket 923-06278

Security screws 923-06633 (2) graphite 923-06872 (2) silver 923-06873 (2) gold 923-06874 (2) sierra blue 923-07197 (2) alpine green

SIM tray 923-06646 dual, graphite 923-06908 single, graphite 923-06909 single, silver 923-06910 single, gold 923-06911 single, sierra blue 923-06913 dual, silver 923-06914 dual, gold 923-06915 dual, sierra blue 923-07195 dual, alpine green 923-07196 single, alpine green

Orderable Parts

iPhone 13 Pro

073-00324-A | 8 2022 Apple Inc. All rights reserved.

Name Numbers Screws

Taptic Engine 923-06258 923-06263 (1) left 923-06280 (1) lower middle 923-06281 (1) right (super screw)

Upper cowling 923-06288 923-06273 (1) upper left 923-06283 (1) upper right 923-06285 (2) lower left, lower right

Orderable Parts

iPhone 13 Pro

073-00324-A | 9 2022 Apple Inc. All rights reserved.

Screws

Never reinstall a screw after it has been removed. Install only new screws. iPhone screw grooves are covered in adhesive that cant be reused.

Use only the torque driver indicated to install new screws during reassembly. Both overtightened screws and loose screws can damage parts.

Warning

Screws

923-06273

923-06283

923-06267

923-06285 923-06268

923-06266

923-06265

923-06265

923-06263

923-06280 923-06633

923-06873 923-06872

923-06874

923-06275

923-06276

923-06273

923-06281

Torque driver (black, 0.35 kgf cm) Torque driver (blue, 0.65 kgf cm) Torque driver (gray, 0.55 kgf cm) Torque driver (green, 0.45 kgf cm)

Crosshead screw Super screw Trilobe screw Security screw

Single screw Screw with super screw underneath

Note: You can use any torque driver to remove screws.

*A super screw has a threaded hole that holds another screw.

923-07197

iPhone 13 Pro

073-00324-A | 10 2022 Apple Inc. All rights reserved.

Tools

Tools

923-02657 Battery press

Cut-resistant gloves 923-06600 Display adhesive press plate

923-01092 Adhesive cutter

923-06848 6.1-inch back protective cover

923-06596 6.1-inch repair tray

923-04878 6.1-inch display protective cover

661-08916 Display press

661-19620 6.1-inch heated display pocket

Tools with part numbers are available for purchase from the Self Service Repair Store. Tools without part numbers can be purchased from electronics supply retailers.

iPhone 13 Pro

073-00324-A | 11 2022 Apple Inc. All rights reserved.

Tools

Safety glasses with side shields

ESD-safe cleaning solution

Ethanol wipes1 661-17619 Heated display removal fixture

Heat-resistant gloves IPA wipes

ESD wrist strap with clip or plug

923-01290 Micro stix bit

922-5065 Nylon probe (black stick) Nitrile or lint-free gloves

ESD mat ESD-safe tweezers

iPhone 13 Pro

073-00324-A | 12 2022 Apple Inc. All rights reserved.

1 Ethanol wipes must contain at least 90% ethanol and no additives except isopropyl alcohol. 2 Clean, dry, untreated sand (810 cups) 3 Sand container (wide-mouthed, quick pour, nonbreakable plastic container with a flip-top lid) 4 The black torque driver kit includes a black torque driver (0.35 kgf cm), Torx security bit (923-0247), and JCIS bit (923-0246).

Tools

Sand2

923-00738 Torque driver (gray, 0.55 kgf cm)

Sand container3

923-0448 Torque driver (blue, 0.65 kgf cm)

923-02066 Super screw bit

923-0248 Torque driver (black, 0.35 kgf cm) kit4

923-00105 Torque driver (green, 0.45 kgf cm)

iPhone 13 Pro

073-00324-A | 13 2022 Apple Inc. All rights reserved.

Tools | Heated Display Removal Fixture

Heated Display Removal Fixture

Note: A rented heated display removal fixture may have different packaging than shown. If your fixture came with a USB cable, set the cable aside. This setup doesnt require it.

1. Remove the fixture from the box. Then remove the packing Styrofoam.

2. Cut and remove the zip tie from the handle.

Dont lift the fixture by the knob.

Caution

iPhone 13 Pro

073-00324-A | 14 2022 Apple Inc. All rights reserved.

Tools | Heated Display Removal Fixture

3. Turn the top knob on the fixture counterclockwise to raise the suction cup. Remove the packing Styrofoam.

4. Turn the emergency stop knob clockwise until it clicks and protrudes from the stop guard.

5. Plug the power cord into the fixture. The fixture wont turn on until you flip the switch on the back.

iPhone 13 Pro

073-00324-A | 15 2022 Apple Inc. All rights reserved.

Battery Safety

Battery Safety

Clean, dry, untreated sand (810 cups) Sand container (wide-mouthed, quick pour, nonbreakable plastic container with a flip-top lid) Heat-resistant gloves Safety glasses with side shields ESD-safe cleaning solution

Warning This device contains a built-in lithium-ion rechargeable battery with soft battery cells. Battery

safety is the number one concern when repairing a device with a built-in lithium-ion battery. Only technicians with the knowledge, experience, and tools required to repair electronic

devices should replace a battery. Improper battery replacement, improper handling of parts, failure to discharge the battery

before repair, or failure to follow the provided instructions could cause battery overheating, swelling, venting, leaking, or a battery thermal event. These events could result in fire, injury, death, data loss, or damage to the device, parts, or other property.

To avoid these potentially harmful events, follow the battery safety guidelines and work in a safety-focused workspace with the tools listed below. Its important to be prepared for all possible outcomes.

How to set up a workspace for battery safety Tools

Workspaces used to repair Apple devices should meet the following criteria:

Nonflammable and electrostatic discharge (ESD)-safe work bench At least 2 feet away from paper and other combustible materials Sand container within reach (2 feet) on both sides of the workspace, not above the workspace Adequate ventilation

iPhone 13 Pro

073-00324-A | 16 2022 Apple Inc. All rights reserved.

Battery Safety

How to handle a battery thermal event

Act immediately if you notice any of the following signs of a battery thermal event:

A battery thermal event is a rapid chemical chain reaction that occurs inside a battery cell. The energy stored in the battery is released suddenly, which can cause outgassing and fire. A battery thermal event can be triggered by physical damage to the battery, improper replacement or repair, or temperatures outside the batterys operating range.

Dont use water or an ABC or carbon dioxide fire extinguisher on a battery thermal event or a device that is undergoing one. Water and ABC or carbon dioxide fire extinguishers wont stop the reaction.

Do smother the battery or device immediately with plenty of clean, dry sand. Dump the sand all at once. Timing is critical the faster you pour all the sand, the sooner the reaction will be contained.

Do contact local fire authorities if further assistance is needed.

Do leave the room for 30 minutes after the reaction is contained. Ventilate the area. Dont return until the area is clear of smoke.

Do wait 30 minutes before touching the device. Wear the heat-resistant gloves and safety glasses with side shields to remove the device from the sand.

Do wipe the affected area with water first. Then wipe the area with an ESD-safe cleaning solution.

Do dispose of the damaged battery or device (including any debris removed from the sand) according to local environmental laws and guidelines.

The lithium-ion battery or a device that contains one begins to smoke or emit sparks or soot. The battery pouch suddenly and quickly puffs out. The lithium-ion battery or a device that contains one begins to emit hissing or popping sounds.

Warning

iPhone 13 Pro

073-00324-A | 17 2022 Apple Inc. All rights reserved.

Battery Safety

Disconnect all external cables. Remove all cases and covers. Turn on the flashlight from the Lock Screen, in Control Center, or by asking Siri. Wait until the device

has turned off and the flashlight is no longer illuminated.

How to handle batteries

The flashlight produces heat. Keep the iPhone in a well-ventilated area while the flashlight is illuminated.

Caution

Fully discharge the battery before you begin a repair. A discharged battery is less susceptible to a battery thermal event. If you cant determine the battery level, dont repair the device.

Warning

Perform the following steps to discharge the battery:

To avoid noxious fumes or a battery thermal event, dont puncture, strike, or crush a lithium-ion battery or a device that contains one.

Keep your workspace clear of foreign objects and sharp materials. Be careful when using sharp tools near the battery. Dont leave loose screws, extra screws, or small parts inside the device. Dont use tools that conduct electricity. Dont throw or drop the battery. Dont expose the battery to excessive heat or sunlight, or temperatures outside the batterys

operating range. Handle and dispose of waste batteries in accordance with local laws and regulations.

Best practices

iPhone 13 Pro

073-00324-A | 18 2022 Apple Inc. All rights reserved.

Broken Glass

Broken Glass

Tools

Warning iPhone displays and some back covers are made of glass. The glass could break if the iPhone is dropped on a hard surface, receives a substantial impact, or is crushed, bent, or deformed. Dont attempt to remove chipped or cracked glass shards.

If the iPhone glass is broken, perform the following steps before you begin a repair:

1. Put on safety glasses with side shields and the cut-resistant gloves. 2. Use a vacuum cleaner to remove glass pieces from your workspace and the iPhone. 3. Attach a protective cover to the broken glass to prevent injury or scattering of glass. Each protective

cover has a release liner underneath. Slowly pull the release liner out from under the protective cover while pressing the cover onto the enclosure.

4. Fold the release liner. Use the shiny side of the release liner to firmly press the protective cover onto the broken glass and smooth out any air bubbles.

5. Wait at least 12 minutes for the bond between the protective cover and the glass to strengthen. 6. If the back glass is broken, place the iPhone into the heated display pocket.

Back protective cover Cut-resistant gloves Display protective cover Heated display pocket Safety glasses with side shields Vacuum cleaner

iPhone 13 Pro

073-00324-A | 19 2022 Apple Inc. All rights reserved.

Broken Glass

If the iPhone has any of the following conditions, stop the repair:

Theres no glass or insufficient glass for the protective cover to adhere to. The protective cover doesnt adhere to the iPhone. The iPhone doesnt fit in the heated display pocket.

You can find a service option at support.apple.com/repair.

iPhone 13 Pro

073-00324-A | 20 2022 Apple Inc. All rights reserved.

First Steps

First Steps

Always perform the following steps before starting a repair:

Back up the iPhone. Discharge the battery fully. Turn off the iPhone. Disconnect all cables. Remove all cases and covers. Clear and clean your workspace. Put on an ESD wrist strap and attach it to a properly grounded ESD mat.

Loose screws, extra screws, or small parts inside the device can damage the battery and cause safety issues. Set aside all parts and screws removed during the repair and account for them at the end of the repair.

ESD (electrostatic discharge, or the release of static electricity) can damage electronic components.

Warning

Caution

Be aware of the following while performing a repair:

The manual for this model may show images of other models, but the procedures are the same. Ensure that you use the correct tools for the model youre repairing.

Take your time. Thoroughly read all instructions and alerts. Magnetizing the torque drivers will make it easier to work with small screws. The end of each flex cable must align with its connector. Press the end of each flex cable to its

connector until it clicks to ensure that its secure.

iPhone 13 Pro

073-00324-A | 21 2022 Apple Inc. All rights reserved.

SIM Tray

SIM-eject tool or paper clip

SIM Tray

Tools

Removal

1. Find your model to locate the SIM tray.

2. Insert a paper clip or SIM-eject tool into the hole next to the SIM tray.

3. Push the paper clip or SIM-eject tool toward the enclosure to eject the SIM tray.

4. Remove the SIM tray.

Reassembly

1. Press the SIM tray back into the side of the enclosure.

iPhone 13 Pro

073-00324-A | 22 2022 Apple Inc. All rights reserved.

Display | Before You Begin

6.1-inch heated display pocket 6.1-inch repair tray Adhesive cutter Display adhesive press plate Display press ESD-safe tweezers Ethanol wipes or isopropyl alcohol (IPA) wipes Heated display removal fixture Heat-resistant gloves JCIS bit Micro stix bit Nylon probe (black stick) Torque driver (black, 0.35 kgf cm) Torque driver (gray, 0.55 kgf cm) Torque driver (green, 0.45 kgf cm) Torx security bit

Display

Tools

Read Battery Safety and follow workspace and battery handling guidelines before you begin. Read Broken Glass before you begin.

Warning

Before You Begin

iPhone 13 Pro

073-00324-A | 23 2022 Apple Inc. All rights reserved.

Display | Before You Begin

Caution To avoid damaging

the lenses, dont touch the TrueDepth camera assembly or nearby parts.

Dont touch the back of the display. Touching the back of the display may affect image quality.

This procedure requires System Configuration. After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Read Heated Display Removal Fixture if youre setting up the fixture for the first time.

Important

iPhone 13 Pro

073-00324-A | 24 2022 Apple Inc. All rights reserved.

Display | Removal

Removal

1. Use a torque driver and the Torx security bit to remove the two security screws, one from each side of the Lightning connector. Set aside the screws.

2. Flip the switch on the back of the heated display removal fixture to turn it on. The internal fan will turn on. Wait for a checkmark to appear on the screen.

Note: If an error code appears on the screen, turn the fixture off and turn it back on.

iPhone 13 Pro

073-00324-A | 25 2022 Apple Inc. All rights reserved.

Display | Removal

3. Gently insert the iPhone into the heated display pocket with the display faceup and the Lightning connector facing the bottom of the pocket.

4. Flip down the clamp on the side of the pocket to lock the iPhone into place.

Ensure that the clamp on the side of the pocket is flipped up.

Important

iPhone 13 Pro

073-00324-A | 26 2022 Apple Inc. All rights reserved.

5. Put on the heat-resistant gloves. Align the cutout on the bottom of the pocket with the rail on the fixture. Slide the pocket with the iPhone onto the rail on the fixture.

Dont insert the pocket into the fixture without wearing the heat-resistant gloves.

Warning

Display | Removal

iPhone 13 Pro

073-00324-A | 27 2022 Apple Inc. All rights reserved.

6. Slide the pocket into the fixture until you hear the pocket click into place.

Note: The screen on the fixture will turn red and the timer will count down from 2 minutes while the pocket heats to the correct temperature. When the timer ends, the fixture will start to beep and the screen will turn green.

Display | Removal

iPhone 13 Pro

073-00324-A | 28 2022 Apple Inc. All rights reserved.

7. Turn the knob on the fixture clockwise to lower the suction cup as close to the iPhone as possible without touching the iPhone.

Note: The fixture will beep until the suction cup is lowered.

8. Grasp the handle and slide the suction cup straight out until the edge of the suction cup aligns with the bottom edge of the display.

Caution Failure to align the edges of the suction cup and the display may damage the iPhone.

Caution To avoid damaging the iPhone, dont turn the knob before the timer beeps.

Display | Removal

iPhone 13 Pro

073-00324-A | 29 2022 Apple Inc. All rights reserved.

9. Turn the knob on the fixture clockwise to lower the suction cup onto the display (1). Then flip down the handle on the suction cup to secure the suction cup to the display (2).

Display | Removal

10. Slowly turn the knob on the fixture counterclockwise until the display begins to separate from the enclosure.

If you dont see a gap between the display and the enclosure immediately, wait 30 seconds. If you still dont see a gap, turn the silver part of the knob counterclockwise until the display begins to separate from the enclosure.

Important

iPhone 13 Pro

073-00324-A | 30 2022 Apple Inc. All rights reserved.

11. Insert the edge of the adhesive cutter between the display and the enclosure. Run the cutter between the display and the enclosure to the right and left as shown until the display partially releases from the enclosure.

Caution To avoid damaging the flex cables, dont tilt up the bottom of the display more than 5 degrees.

Display | Removal

iPhone 13 Pro

073-00324-A | 31 2022 Apple Inc. All rights reserved.

12. Flip up the handle to release the suction cup (1). Gently slide the flat end of the black stick under the edge of the suction cup to release it from the display (2).

13. Press the eject button on the side of the pocket to release the pocket from the fixture.

Caution Dont turn the knob. Turning the knob may damage the flex cables.

Display | Removal

iPhone 13 Pro

073-00324-A | 32 2022 Apple Inc. All rights reserved.

14. Hold both sides of the pocket and slide it straight out of the fixture.

15. Flip up the clamp on the side of the pocket to release the iPhone (1). Hold the area outlined in blue and gently remove the iPhone from the pocket (2).

16. Place the iPhone into the repair tray with the display faceup and the Lightning connector facing the cutout. Remove the gloves.

Display | Removal

iPhone 13 Pro

073-00324-A | 33 2022 Apple Inc. All rights reserved.

17. Slide the display slightly toward the bottom of the iPhone.

18. Insert the edge of the adhesive cutter into the top of the iPhone between the display and the enclosure. Hold the adhesive cutter at a 45-degree angle. Start at the middle and cut along the top and sides of the iPhone until the display is free.

To avoid damaging the flex cables, dont tilt up the bottom of the display more than 5 degrees.

Caution

Display | Removal

iPhone 13 Pro

073-00324-A | 34 2022 Apple Inc. All rights reserved.

19. Insert the repair tray suction cups into the slots in the repair tray.

20. Tilt up the display toward the suction cups. Press the top and bottom edges of the display to secure it to the suction cups.

Caution To avoid damaging the

enclosure or display, ensure that the internal display clips are released before you tilt up the display.

Dont damage the flex cables as you tilt up the display.

If the battery is dented, punctured, or otherwise damaged, stop the repair. You can find a service option at support.apple.com/repair.

Warning

Display | Removal

iPhone 13 Pro

073-00324-A | 35 2022 Apple Inc. All rights reserved.

21. Use a torque driver and the Micro stix bit to remove

the three trilobe screws (1) from the lower cowling. Set aside the screws.

22. Use ESD-safe tweezers to remove the lower cowling. Save the cowling for reassembly.

23. Use a torque driver and the Micro stix bit to remove the two trilobe screws (2) from the upper cowling. Set aside the screws.

25. Use ESD-safe tweezers to tilt up the upper cowling. Then slide the cowling out from under the ambient light sensor flex cable. Save the cowling for reassembly.

24. Use a torque driver and the JCIS bit to remove the two crosshead screws (3) from the upper cowling. Hold the cowling in place while you remove the last screw. Set aside the screws.

Dont tear the ambient light sensor flex cable while removing the cowling.

Caution

Display | Removal

iPhone 13 Pro

073-00324-A | 36 2022 Apple Inc. All rights reserved.

26. Use the black stick to lift the end of the battery flex cable (1) off the connector.

28. Hold the display by the edges. Pull the tabs on the suction cups to release them from the display. Then set the display facedown on a clean, flat surface.

29. Remove the suction cups from the repair tray.

Display | Removal

You must disconnect the battery flex cable first to ensure that the iPhone stays turned off.

Caution

27. Use the black stick to lift the ends of the display flex cable (2) and ambient light sensor flex cable (3) off the connectors.

iPhone 13 Pro

073-00324-A | 37 2022 Apple Inc. All rights reserved.

30. Use ESD-safe tweezers to pick up the adhesive. Then use the tweezers or black stick to pull the adhesive from the enclosure. Repeat this process until all the adhesive is removed from the perimeter of the enclosure.

Dont touch the TrueDepth camera assembly, grounding springs, or nearby parts.

Caution

Display | Removal

iPhone 13 Pro

073-00324-A | 38 2022 Apple Inc. All rights reserved.

32. Use ethanol wipes or IPA wipes to clean any adhesive residue from the enclosure.

Dont use ethanol wipes or IPA wipes on the display. Ethanol or isopropyl alcohol may damage the display and affect image quality.

Caution

31. Use ESD-safe tweezers to remove the grounding foam from the top of the enclosure above the TrueDepth camera.

Display | Removal

iPhone 13 Pro

073-00324-A | 39 2022 Apple Inc. All rights reserved.

Reassembly

1. Inspect the internal display clips for damage before reassembly. Ensure that the internal display clips are at a 90-degree angle and arent bent or damaged.

2. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Display | Reassembly

If the internal display clips are damaged, you may need to replace the display.

If youre installing a replacement display, peel the protective liner from the top and underside of it.

Important

iPhone 13 Pro

073-00324-A | 40 2022 Apple Inc. All rights reserved.

Display | Reassembly

4. Align the replacement display adhesive over the enclosure with the grounding foam on top. Ensure that the top holes of the adhesive align over the TrueDepth camera assembly.

Ensure that youve removed all adhesive residue from the display and the enclosure before you apply the replacement display adhesive.

Caution

If the TrueDepth camera is positioned incorrectly, use the black stick to move it into the correct position.

Caution

3. Inspect the TrueDepth camera. Ensure that the top edge of the TrueDepth camera is under the lip of the enclosure.

Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

Warning

iPhone 13 Pro

073-00324-A | 41 2022 Apple Inc. All rights reserved.

Display | Reassembly

5. The replacement display adhesive has a top release liner, a middle release liner, and a flexible bottom release liner. Grasp the tab on the bottom release liner. Then slowly pull the bottom release liner (1) out from under the adhesive (2) while pressing the adhesive onto the enclosure.

Dont remove the top release liner yet.

Important

Bottom release liner

Adhesive

Note: The replacement display adhesive for your model may look different from the illustration, but the steps are the same.

iPhone 13 Pro

073-00324-A | 42 2022 Apple Inc. All rights reserved.

Display | Reassembly

6. Use the black stick to gently adhere the grounding foam as shown.

7. Place the display adhesive press plate on top of the enclosure with the icon in the top right corner as shown.

Failure to adhere the grounding foam may damage the display, Wi-Fi, or TrueDepth camera.

Caution

iPhone 13 Pro

073-00324-A | 43 2022 Apple Inc. All rights reserved.

8. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

Display | Reassembly

9. Wait until the timer on the display press beeps. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

iPhone 13 Pro

073-00324-A | 44 2022 Apple Inc. All rights reserved.

10. Remove the repair tray from the display press and remove the press plate.

11. Remove the left section of the top release liner first (1). Then remove the three sections running along the top (2), right (3), and bottom (4).

12. Insert the suction cups into the repair tray.

Dont remove the middle release liner yet.

Important

13. Align the left edge of the display with the left edge of the enclosure. Gently press along the edges of the display to secure it to the suction cups.

Display | Reassembly

Top release liner

iPhone 13 Pro

073-00324-A | 45 2022 Apple Inc. All rights reserved.

16. Use ESD-safe tweezers to position the lower cowling over the ends of the display and battery flex cables.

18. Use the green torque driver and JCIS bit to install two new crosshead screws into the upper cowling (2).

17. Use ESD-safe tweezers to slide the tab of the upper cowling behind the ambient light sensor flex cable (1). Then lower the cowling over the end of the flex cable.

19. Use the black torque driver and Micro stix bit to install two new trilobe screws into the upper cowling (3) and three new trilobe screws into the lower cowling (4).

Display | Reassembly

14. Press the ends of the display flex cable (1) and ambient light sensor flex cable (2) to the connectors. Press evenly along the length of each connector.

15. Press the end of the battery flex cable to the connector (3). Press evenly along the length of the connector.

iPhone 13 Pro

073-00324-A | 46 2022 Apple Inc. All rights reserved.

20. Peel the first strip from the middle release liner (1) clockwise, starting near the bottom right of the enclosure. Peel the second strip (2) counterclockwise, starting near the bottom right of the enclosure. Peel the third strip (3) clockwise, starting near the bottom left of the enclosure.

21. Inspect the display adhesive to ensure that its in the correct position and not damaged or wrinkled. If the adhesive is damaged, remove it and apply replacement adhesive.

22. Repeat step 3 to ensure that the TrueDepth camera is in the correct position. Then continue to step 23.

23. Pull the tabs on the suction cups to release them from the display. Tilt down the display to rest on the enclosure.

24. Remove the suction cups from the repair tray.

Display | Reassembly

Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

Warning

Middle release liner

iPhone 13 Pro

073-00324-A | 47 2022 Apple Inc. All rights reserved.

25. Press all four corners of the display simultaneously. Then press along the edges of the display until you hear a click and the display is flush with the enclosure.

Ensure that the flex cables arent trapped between the display and the enclosure. Feel the edges of the display for variations or gaps. If the display isnt flush, repeat all removal steps and check the flex cables for damage. Then repeat reassembly steps 1 through 25.

Caution

Display | Reassembly

iPhone 13 Pro

073-00324-A | 48 2022 Apple Inc. All rights reserved.

26. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

Display | Reassembly

27. Wait until the timer on the display press beeps. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

iPhone 13 Pro

073-00324-A | 49 2022 Apple Inc. All rights reserved.

29. Use the gray torque driver and Torx security bit to install two new security screws, one on each side of the Lightning connector. As you install the screws, press lightly on the display near the Lightning connector.

If the screws arent flush, remove and set aside the screws. Repeat step 29 to install another new set of screws. If the new screws still arent flush, repeat all removal and reassembly steps.

Caution

System Configuration is required if youve installed a replacement display, battery, or camera. Disregard notifications about iPhone features on the Lock Screen until you complete System Configuration.

After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

Display | Reassembly

28. Remove the repair tray from the display press.

iPhone 13 Pro

073-00324-A | 50 2022 Apple Inc. All rights reserved.

Bottom Speaker

Bottom Speaker | Before You Begin

6.1-inch repair tray ESD-safe tweezers JCIS bit Nylon probe (black stick) Torque driver (green, 0.45 kgf cm)

Tools

Display

Remove the following part before you begin:

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Warning

Caution Avoid touching the grounding springs on the bottom speaker.

This procedure requires a replacement battery shim, which is available with a replacement bottom speaker, Taptic Engine, or battery. Its not a separate orderable part.

Important

Before You Begin

iPhone 13 Pro

073-00324-A | 51 2022 Apple Inc. All rights reserved.

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Removal

Bottom Speaker | Removal

2. Run the flat end of the black stick between the battery shim and the Taptic Engine and bottom speaker to loosen the battery shim.

3. Use a torque driver and the JCIS bit to remove the four crosshead screws from the bottom speaker. Set aside the screws.

iPhone 13 Pro

073-00324-A | 52 2022 Apple Inc. All rights reserved.

Bottom Speaker | Removal

4. Remove the bottom speaker from the enclosure.

5. Use ESD-safe tweezers to remove the battery shim from the enclosure. Discard the shim.

iPhone 13 Pro

073-00324-A | 53 2022 Apple Inc. All rights reserved.

Bottom Speaker | Reassembly

1. Rotate the repair tray. Ensure that the rubber gasket is positioned as shown. If the gasket is out of position, use ESD-safe tweezers to reposition it.

Reassembly

2. Position the bottom speaker in the enclosure.

3. Rotate the repair tray. Use the green torque driver and JCIS bit to install four new crosshead screws into the bottom speaker. Press the bottom speaker down while you install the screws.

Dont damage the grounding springs on the bottom speaker.

Caution

iPhone 13 Pro

073-00324-A | 54 2022 Apple Inc. All rights reserved.

Bottom Speaker | Reassembly

Display

Reinstall the following part to complete reassembly:

4. Remove the adhesive release liner from the replacement battery shim.

5. Insert the replacement battery shim between the top edges of the bottom speaker and Taptic Engine and the bottom edge of the battery. Ensure that the adhesive side of the shim faces the Taptic Engine and bottom speaker.

6. Run the black stick along the top of the battery shim to adhere it into place.

iPhone 13 Pro

073-00324-A | 55 2022 Apple Inc. All rights reserved.

Camera

6.1-inch repair tray ESD-safe tweezers JCIS bit Micro stix bit Nitrile or lint-free gloves Nylon probe (black stick) Torque driver (black, 0.35 kgf cm) Torque driver (gray, 0.55 kgf cm)

Tools

Display

Remove the following part before you begin:

Camera | Before You Begin

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Warning

Before You Begin

Caution To avoid damaging

the lenses, dont touch the TrueDepth camera assembly or nearby parts.

Avoid the grounding spring on the camera cowling.

This procedure requires System Configuration. After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

iPhone 13 Pro

073-00324-A | 56 2022 Apple Inc. All rights reserved.

2. Use a torque driver and the Micro stix bit to remove the four trilobe screws from the camera cowling (1). Set aside the screws.

Removal

Camera | Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

3. Use a torque driver and the JCIS bit to remove the crosshead screw from the camera cowling (2). Set aside the screw.

4. Use ESD-safe tweezers to tilt up the left side of the camera cowling (1). Then slide the cowling tabs out of the slots on the right side of the enclosure (2). Save the cowling for reassembly.

iPhone 13 Pro

073-00324-A | 57 2022 Apple Inc. All rights reserved.

Camera | Removal

5. Use ESD-safe tweezers to gently lift the ends of the two camera flex cables off the connectors.

6. Gently hold the camera flex cables together and lift the cameras out of the enclosure.

iPhone 13 Pro

073-00324-A | 58 2022 Apple Inc. All rights reserved.

1. Put on the gloves to prevent contamination of the camera lenses. Then hold the replacement cameras with the lenses facedown and remove the protective cover from the camera lenses.

2. Position the cameras in the enclosure. Ensure that the camera flex cables are inside the channel between the battery and the camera well.

Reassembly

3. Press the ends of the two camera flex cables to the connectors.

Camera | Reassembly

iPhone 13 Pro

073-00324-A | 59 2022 Apple Inc. All rights reserved.

4. Lightly press the cameras into the enclosure.

5. The camera cowling has tabs that fit into slots on the right side of the enclosure. Hold the cowling with ESD-safe tweezers and slide the cowling tabs into the slots. Then lower the cowling onto the cameras.

Caution Ensure that the screw

cutouts in the camera cowling align with the screw holes. A misaligned camera cowling may affect display image quality.

Ensure that the grounding spring on the camera cowling isnt damaged. Avoid touching the grounding spring as you reinstall the cowling.

6. Hold down the camera cowling. Then use the black torque driver and Micro stix bit to install one new trilobe screw into the middle of the cowling.

Camera | Reassembly

iPhone 13 Pro

073-00324-A | 60 2022 Apple Inc. All rights reserved.

7. Use the black torque driver and Micro stix bit to install three new trilobe screws into the camera cowling (1).

8. Use the gray torque driver and JCIS bit to install one new crosshead screw into the camera cowling (2).

Display

Reinstall the following part to complete reassembly:

After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

Camera | Reassembly

iPhone 13 Pro

073-00324-A | 61 2022 Apple Inc. All rights reserved.

Camera | Reassembly

During System Configuration, you will perform LiDAR Scanner calibration. Prepare for calibration by reviewing the following steps:

1. Use a well-lit area containing objects of different shapes and sizes.

2. Sit or stand 1 to 2 feet from the objects.

3. Hold the device vertically and rest your elbow on your body to help stabilize your arm.

4. Start scanning by slowly panning back and forth to the left and right of the starting point. Follow the directions that appear on the device screen.

Note: The calibration process takes approximately 5 minutes.

iPhone 13 Pro

073-00324-A | 62 2022 Apple Inc. All rights reserved.

Taptic Engine

6.1-inch repair tray ESD-safe tweezers JCIS bit Nylon probe (black stick) Super screw bit Torque driver (blue, 0.65 kgf cm)

Tools

Display Bottom speaker

Remove the following parts before you begin:

Taptic Engine | Before You Begin

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Warning

Before You Begin

iPhone 13 Pro

073-00324-A | 63 2022 Apple Inc. All rights reserved.

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

4. Lift the end of the Taptic Engine flex cable off the connector.

Removal

Taptic Engine | Removal

2. Use a torque driver and the JCIS bit to remove the two crosshead screws from the Taptic Engine (1). Set aside the screws.

3. Use a torque driver and the super screw bit to remove the super screw from the Taptic Engine (2). Set aside the screw.

5. Remove the Taptic Engine from the enclosure.

iPhone 13 Pro

073-00324-A | 64 2022 Apple Inc. All rights reserved.

Reassembly

Taptic Engine | Reassembly

2. Press the end of the Taptic Engine flex cable to the connector.

1. Position the Taptic Engine in the enclosure.

iPhone 13 Pro

073-00324-A | 65 2022 Apple Inc. All rights reserved.

3. Use the blue torque driver and super screw bit to install one new super screw into the Taptic Engine (1).

Taptic Engine | Reassembly

4. Use the blue torque driver and JCIS bit to install two new crosshead screws into the Taptic Engine (2).

Reinstall the following parts to complete reassembly:

Bottom speaker Display

iPhone 13 Pro

073-00324-A | 66 2022 Apple Inc. All rights reserved.

Battery

Battery | Before You Begin

6.1-inch repair tray Battery press ESD-safe cleaning solution ESD-safe tweezers Ethanol wipes or isopropyl alcohol (IPA) wipes Heat-resistant gloves Nitrile or lint-free gloves Nylon probe (black stick) Safety glasses with side shields Sand Sand container

Tools

Display Bottom speaker Taptic Engine

Remove the following parts before you begin:

A battery should be replaced only by individual technicians with the knowledge and experience to repair electronic devices. Improper battery replacement, improper handling of parts, or failure to follow the provided instructions could result in fire, injury, data loss, or damage to the device, parts, or other property.

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Warning

Before You Begin

iPhone 13 Pro

073-00324-A | 67 2022 Apple Inc. All rights reserved.

Battery | Before You Begin

To avoid damaging the lenses, dont touch the TrueDepth camera assembly or nearby parts.

Caution

This procedure requires System Configuration. After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

iPhone 13 Pro

073-00324-A | 68 2022 Apple Inc. All rights reserved.

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Use ESD-safe tweezers to grasp the bottom right battery adhesive tab. Gently peel the adhesive tab away from the battery.

Removal

Note: The battery has three adhesive tabs.

Battery | Removal

Don't scrape or puncture the battery with the tweezers.

Warning

iPhone 13 Pro

073-00324-A | 69 2022 Apple Inc. All rights reserved.

Battery | Removal

3. Hold down the iPhone. Use ESD-safe tweezers to continue peeling the adhesive tab from the battery.

Peel the adhesive tab completely from the battery before twisting it around the tweezers.

Important

4. Keep the tweezers close and parallel to the battery and twist until you see white adhesive strip on the tweezers.

Dont pull the tweezers until the white adhesive is wrapped around them.

Important

iPhone 13 Pro

073-00324-A | 70 2022 Apple Inc. All rights reserved.

5. Pull the tweezers toward the bottom of the iPhone and continue to twist the adhesive strip until youve removed the entire strip.

Dont pull the adhesive strip against parts or screws.

Caution

6. Use ESD-safe tweezers to grasp the bottom left battery adhesive tab. Gently peel the adhesive tab away from the battery.

7. Repeat steps 3 through 5 to remove the bottom left adhesive strip from the battery. If you remove the entire strip, continue to step 8.

Important If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat steps 4 and 5. If you cant see the tab or strip, continue to step 8.

Important If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat steps 4 and 5. If you cant see the tab or strip, continue to step 6.

8. Rotate the repair tray and put on the nitrile or lint-free gloves.

9. Hold down the iPhone. Use ESD-safe tweezers to gently peel the battery adhesive tab from the top of the battery. Then twist the tweezers to wrap the adhesive tab around them.

Important Hold the tweezers close and parallel to the battery as you twist.

Battery | Removal

iPhone 13 Pro

073-00324-A | 71 2022 Apple Inc. All rights reserved.

10. Keep the tweezers in the channel between the battery and the camera cowling. Continue to slowly twist the tweezers until youve removed the entire adhesive strip.

If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat step 10. If you cant see the tab or strip, continue to step 11.

Important

Battery | Removal

iPhone 13 Pro

073-00324-A | 72 2022 Apple Inc. All rights reserved.

11. If all three battery adhesive strips were fully removed, continue to step 13. If at least one strip was fully removed, continue to step 12.

If all three strips were broken and cant be retrieved, dont forcibly pry the battery. Stop the repair. You can find a service option at support.apple.com/repair.

Warning

Battery | Removal

iPhone 13 Pro

073-00324-A | 73 2022 Apple Inc. All rights reserved.

Battery | Removal

12. Insert the flat end of the black stick into one of the insertion points as shown. Ensure that the black stick is inserted into a point where the battery strip has been fully removed. Dont insert the black stick into a point where the battery tab or strip is broken.

When using the black stick to remove the battery from the enclosure, don't damage the flex cables. Dont scrape, rip, tear, or otherwise damage the polyester film or other areas. If damage occurs, replace the iPhone.

Caution

iPhone 13 Pro

073-00324-A | 74 2022 Apple Inc. All rights reserved.

14. Remove the battery from the enclosure. Then inspect the enclosure for damage. If the enclosure is damaged, replace the iPhone.

To avoid damage, dont press the black stick on the edge of the enclosure as you lift the battery.

Caution

If you cant remove the battery, stop the repair. You can find a service option at support.apple.com/repair.

Warning

Battery | Removal

13. Slightly lift the battery with the black stick just enough to grasp underneath the battery.

iPhone 13 Pro

073-00324-A | 75 2022 Apple Inc. All rights reserved.

3. Use ethanol wipes or IPA wipes on the area shown in blue to remove any remaining adhesive from the enclosure.

Reassembly

Battery | Reassembly

1. Reinstall the Taptic Engine.

Caution Dont use ethanol wipes or IPA wipes on the areas shown in red. Ethanol or isopropyl alcohol may damage the polyester film and wireless charging unit.

2. Reinstall the bottom speaker.

Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

Warning

iPhone 13 Pro

073-00324-A | 76 2022 Apple Inc. All rights reserved.

Battery | Reassembly

5. Hold the battery over the enclosure with the protective cover faceup. Align the bottom of the battery with the bottom speaker (1) and the left edge with the logic board (2). Then lower the battery into the enclosure.

4. Peel the pink release liner from the underside of the replacement battery.

Dont remove the battery protective cover from the top of the battery yet.

Important

iPhone 13 Pro

073-00324-A | 77 2022 Apple Inc. All rights reserved.

6. Place the repair tray and the enclosure into the battery press. The repair tray has a cutout at the bottom and two slots in the center. Align the left slot on the repair tray with the pin on the battery press.

7. Flip down the red lever to lower the roller onto the battery.

Battery | Reassembly

iPhone 13 Pro

073-00324-A | 78 2022 Apple Inc. All rights reserved.

8. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.

9. Flip up the red lever.

Battery | Reassembly

iPhone 13 Pro

073-00324-A | 79 2022 Apple Inc. All rights reserved.

10. Align the right slot on the repair tray with the pin on the battery press.

11. Flip down the red lever.

Battery | Reassembly

iPhone 13 Pro

073-00324-A | 80 2022 Apple Inc. All rights reserved.

12. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.

13. Flip up the red lever.

Battery | Reassembly

iPhone 13 Pro

073-00324-A | 81 2022 Apple Inc. All rights reserved.

Display

Reinstall the following part to complete reassembly:

Gently shake the iPhone. If the battery sounds loose, remove the display and the battery. Then complete battery reassembly with another replacement battery.

Warning

14. Remove the repair tray from the battery press.

15. Hold the edges of the protective cover. Pull the release tabs on the protective cover

Manualsnet FAQs

If you want to find out how the iPhone 13 Pro Apple works, you can view and download the Apple iPhone 13 Pro Smartphone Repair Manual on the Manualsnet website.

Yes, we have the Repair Manual for Apple iPhone 13 Pro as well as other Apple manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Repair Manual should include all the details that are needed to use a Apple iPhone 13 Pro. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Apple iPhone 13 Pro Smartphone Repair Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Apple iPhone 13 Pro Smartphone Repair Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Apple iPhone 13 Pro Smartphone Repair Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Apple iPhone 13 Pro Smartphone Repair Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Apple iPhone 13 Pro Smartphone Repair Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.