Contents

Apple iPhone 12 Pro Smartphone Repair Manual PDF

1 of 93
1 of 93

Summary of Content for Apple iPhone 12 Pro Smartphone Repair Manual PDF

2022 Apple Inc. All rights reserved.

Repair Manual iPhone 12 Pro

iPhone 12 Pro

073-00292-A | 2 2022 Apple Inc. All rights reserved.

Contents

3 Introduction

Basics

6 Internal View 7 Orderable Parts 9 Screws 10 Tools

Safety

15 Battery Safety 18 Broken Glass

Procedures

20 First Steps 21 SIM Tray 22 Display 53 Camera 60 Speaker 64 Battery 82 Taptic Engine

Contents

iPhone 12 Pro

073-00292-A | 3 2022 Apple Inc. All rights reserved.

Introduction

Introduction

This manual includes technical instructions for replacing genuine Apple parts in iPhone and is intended for individual technicians with the knowledge, experience, and tools required to repair electronic devices.

Important Read the entire manual first. If youre not comfortable performing the repairs as instructed in

this manual, dont proceed. Always use the latest version of this document available at support.apple.com/manuals/

repair+manual.

Warning Failure to follow the repair instructions or to use genuine Apple parts or proper tools may

cause fire or other safety issues and lead to personal injury or death. iPhone 7 and later are classified as Class 1 Laser products per IEC 60825-1 Ed. 3.

These devices comply with 21 CFR 1040.10 and 1040.11, except for conformance with IEC 60825-1 Ed. 3., as described in Laser Notice No. 56, dated May 8, 2019. These devices contain one or more lasers. Use other than as described in the user guide, repair, or disassembly may cause damage, which could result in hazardous exposure to infrared laser emissions that are not visible.

Failure to follow the repair instructions or to use genuine Apple parts or proper tools may damage the iPhone, parts, or other property, or compromise the devices functionality or water resistance.

Caution

Warranty information Damage caused by repairs performed outside of Apple or the Apple Authorized Service network is not covered by Apples warranty or AppleCare plans. Such damage may cause future repairs to be subject to out-of-warranty costs or render the device ineligible for future repairs by Apple or Apple Authorized Service Providers.

iPhone 12 Pro

073-00292-A | 4 2022 Apple Inc. All rights reserved.

Introduction

Software tools

A System Configuration step may be required at the end of your repair. System Configuration is a postrepair software tool that completes the repair for genuine Apple parts. Running System Configuration has a number of purposes that vary based on the part replaced.

What System Configuration does Why its important Transfers factory calibration values

Certain parts like displays, cameras, and ambient light sensors have calibration values that are customized to each individual part during manufacturing. Transferring these values ensures maximum performance and quality after a repair.

Links Secure Element and biometric authentication parts

After repair of a logic board or a biometric authentication part (Touch ID or Face ID), linking the biometric sensors to the Secure Enclave on the logic board is required to ensure device security.

Ensures repair integrity

After a hardware repair, software checks are performed to ensure repair integrity. Repair integrity means that a genuine Apple part has been correctly installed.

Assigns wireless region

To comply with regional communications regulations, a wireless region must be assigned to your logic board.

Updates firmware Keeping firmware up to date ensures that the device has all the latest security and performance features.

The heated display removal fixture softens adhesive to allow separation of the display from the enclosure. The fixture is used with a heated display pocket designed for the devices specific dimensions.

The display press applies the appropriate amount of pressure to secure new adhesive during display installation. The display press is used with a repair tray and display adhesive press plate designed for the devices specific dimensions.

The battery press applies the appropriate amount of pressure to secure new adhesive during battery installation. The battery press is used with a repair tray designed for the devices specific dimensions.

Ordering tools and parts

You can learn how to order genuine Apple parts and tools at support.apple.com/self-service-repair. During the purchase process, enter the manual ID FWRUJK to indicate that youve read this manual in its entirety and agree that you have the knowledge and experience to perform your intended repair.

Tools and parts Hardware tools

Apple tools are designed to apply the appropriate heat, force, and torque during repairs, and to withstand high-volume professional use.

iPhone 12 Pro

073-00292-A | 5 2022 Apple Inc. All rights reserved.

Introduction

System Configuration requires a strong Wi-Fi network capable of 1.0 Mbps download and upload speeds, with less than 400 ms latency and less than 2% packet loss. Estimated data usage to run System Configuration is 622 MB.

The device must be running the latest version of iOS and not a beta version.

Learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important Supplemental information for successfully completing procedures; neither a Warning nor a Caution

Caution Instructions for reducing risk of data loss or device hardware damage

Alerts

Failure to follow alerts could result in fire, injury, data loss, or damage to the device, parts, or other property.

Warning Instructions for reducing risk of personal injury

iPhone 12 Pro

073-00292-A | 6 2022 Apple Inc. All rights reserved.

Internal View

1. TrueDepth camera assembly 2. Cameras 3. Camera flex cable 4. Top battery adhesive tabs 5. Battery 6. Bottom battery adhesive tabs 7. Speaker 8. Lightning connector 9. Bottom microphones

10. Taptic Engine 11. Taptic Engine connector cowling 12. SIM reader 13. SIM reader connector cowling 14. Multi-Touch connector 15. Battery flex cable 16. Display connector 17. Dock flex cable 18. Receiver/ambient light sensor/proximity sensor connector

Internal View

iPhone 12 Pro

073-00292-A | 7 2022 Apple Inc. All rights reserved.

Orderable Parts

Name Numbers Screws

Battery 661-17920

Camera 661-17922

Camera cowling 923-04990 923-05054 (3) upper left, upper middle, lower left 923-05055 (1) middle

Display 661-18504 LL661-18504 (U.S.)

Display adhesive 923-04894

Lower cowling 923-04987 923-04982 (2)

Rubber gasket 923-04937

Security screws 923-05064 (2) pacific blue 923-05065 (2) silver 923-05066 (2) gold 923-05067 (2) graphite

SIM reader connector cowling 923-04983 923-04978 (2)

SIM tray 923-05056 single, graphite 923-05057 dual, graphite 923-05058 single, silver 923-05059 single, gold 923-05060 single, pacific blue 923-05061 dual, silver 923-05062 dual, gold 923-05063 dual, pacific blue

Speaker 923-04915 923-05052 (4)

Taptic Engine 923-04979 923-04980 (3) upper left, right, SIM reader lower right (super screws) 923-04981 (1) lower middle 923-04982 (1) SIM reader upper left

Orderable Parts

iPhone 12 Pro

073-00292-A | 8 2022 Apple Inc. All rights reserved.

Name Numbers Screws

Taptic Engine connector cowling

923-04977 923-04978 (2)

Upper cowling 923-04985 923-04982 (3) upper right, lower left, lower right 923-04988 (1) upper left

Orderable Parts

iPhone 12 Pro

073-00292-A | 9 2022 Apple Inc. All rights reserved.

Screws

Never reinstall a screw after it has been removed. Install only new screws. iPhone screw grooves are covered in adhesive that cant be reused.

Use only the torque driver indicated to install new screws during reassembly. Both overtightened screws and loose screws can damage parts.

Warning

923-05054

923-05064 923-05065 923-05066 923-05067

923-05055

923-05052

923-04981

923-04982

923-04978

923-04982

923-04988

Screws

Torque driver (black, 0.35 kgf cm) Torque driver (gray, 0.55 kgf cm) Torque driver (green, 0.45 kgf cm)

Crosshead screw Super screw* Trilobe screw Security screw

Single screw Screw with super screw underneath

923-04980

923-04980

Note: You can use any torque driver to remove screws.

*A super screw has a threaded hole that holds another screw.

iPhone 12 Pro

073-00292-A | 10 2022 Apple Inc. All rights reserved.

Tools

Tools

923-02657 Battery press

Cut-resistant gloves 923-04911 Display adhesive press plate

923-01092 Adhesive cutter

923-04877 6.1-inch back protective cover

923-04908 6.1-inch repair tray

923-04878 6.1-inch display protective cover

661-08916 Display press

661-19620 6.1-inch heated display pocket

Tools with part numbers are available for purchase from the Self Service Repair Store. Tools without part numbers can be purchased from electronics supply retailers.

iPhone 12 Pro

073-00292-A | 11 2022 Apple Inc. All rights reserved.

Tools

ESD-safe tweezers

Ethanol wipes1 661-17619 Heated display removal fixture

Heat-resistant gloves IPA wipes

ESD wrist strap with clip or plug

923-01290 Micro stix bit

Safety glasses with side shields 922-5065 Nylon probe (black stick) Nitrile or lint-free gloves

ESD mat ESD-safe cleaning solution

iPhone 12 Pro

073-00292-A | 12 2022 Apple Inc. All rights reserved.

Tools

1 Ethanol wipes must contain at least 90% ethanol and no additives except isopropyl alcohol. 2 Clean, dry, untreated sand (810 cups) 3 Sand container (wide-mouthed, quick pour, nonbreakable plastic container with a flip-top lid) 4 The black torque driver kit includes a black torque driver (0.35 kgf cm), Torx security bit (923-0247), and JCIS bit (923-0246).

Sand2

923-00105 Torque driver (green, 0.45 kgf cm)

Sand container3

923-00738 Torque driver (gray, 0.55 kgf cm)

923-02066 Super screw bit

923-0248 Torque driver (black, 0.35 kgf cm) kit4

iPhone 12 Pro

073-00292-A | 13 2022 Apple Inc. All rights reserved.

Tools | Heated Display Removal Fixture

Heated Display Removal Fixture

Note: A rented heated display removal fixture may have different packaging than shown. If your fixture came with a USB cable, set the cable aside. This setup doesnt require it.

1. Remove the fixture from the box. Then remove the packing Styrofoam.

2. Cut and remove the zip tie from the handle.

Dont lift the fixture by the knob.

Caution

iPhone 12 Pro

073-00292-A | 14 2022 Apple Inc. All rights reserved.

Tools | Heated Display Removal Fixture

3. Turn the top knob on the fixture counterclockwise to raise the suction cup. Remove the packing Styrofoam.

4. Turn the emergency stop knob clockwise until it clicks and protrudes from the stop guard.

5. Plug the power cord into the fixture. The fixture wont turn on until you flip the switch on the back.

iPhone 12 Pro

073-00292-A | 15 2022 Apple Inc. All rights reserved.

Battery Safety

Battery Safety

Clean, dry, untreated sand (810 cups) Sand container (wide-mouthed, quick pour, nonbreakable plastic container with a flip-top lid) Heat-resistant gloves Safety glasses with side shields ESD-safe cleaning solution

Warning This device contains a built-in lithium-ion rechargeable battery with soft battery cells. Battery

safety is the number one concern when repairing a device with a built-in lithium-ion battery. Only technicians with the knowledge, experience, and tools required to repair electronic

devices should replace a battery. Improper battery replacement, improper handling of parts, failure to discharge the battery

before repair, or failure to follow the provided instructions could cause battery overheating, swelling, venting, leaking, or a battery thermal event. These events could result in fire, injury, death, data loss, or damage to the device, parts, or other property.

To avoid these potentially harmful events, follow the battery safety guidelines and work in a safety-focused workspace with the tools listed below. Its important to be prepared for all possible outcomes.

How to set up a workspace for battery safety Tools

Workspaces used to repair Apple devices should meet the following criteria:

Nonflammable and electrostatic discharge (ESD)-safe work bench At least 2 feet away from paper and other combustible materials Sand container within reach (2 feet) on both sides of the workspace, not above the workspace Adequate ventilation

iPhone 12 Pro

073-00292-A | 16 2022 Apple Inc. All rights reserved.

Battery Safety

How to handle a battery thermal event

Act immediately if you notice any of the following signs of a battery thermal event:

A battery thermal event is a rapid chemical chain reaction that occurs inside a battery cell. The energy stored in the battery is released suddenly, which can cause outgassing and fire. A battery thermal event can be triggered by physical damage to the battery, improper replacement or repair, or temperatures outside the batterys operating range.

Dont use water or an ABC or carbon dioxide fire extinguisher on a battery thermal event or a device that is undergoing one. Water and ABC or carbon dioxide fire extinguishers wont stop the reaction.

Do smother the battery or device immediately with plenty of clean, dry sand. Dump the sand all at once. Timing is critical the faster you pour all the sand, the sooner the reaction will be contained.

Do contact local fire authorities if further assistance is needed.

Do leave the room for 30 minutes after the reaction is contained. Ventilate the area. Dont return until the area is clear of smoke.

Do wait 30 minutes before touching the device. Wear the heat-resistant gloves and safety glasses with side shields to remove the device from the sand.

Do wipe the affected area with water first. Then wipe the area with an ESD-safe cleaning solution.

Do dispose of the damaged battery or device (including any debris removed from the sand) according to local environmental laws and guidelines.

The lithium-ion battery or a device that contains one begins to smoke or emit sparks or soot. The battery pouch suddenly and quickly puffs out. The lithium-ion battery or a device that contains one begins to emit hissing or popping sounds.

Warning

iPhone 12 Pro

073-00292-A | 17 2022 Apple Inc. All rights reserved.

Battery Safety

Disconnect all external cables. Remove all cases and covers. Turn on the flashlight from the Lock Screen, in Control Center, or by asking Siri. Wait until the device

has turned off and the flashlight is no longer illuminated.

How to handle batteries

The flashlight produces heat. Keep the iPhone in a well-ventilated area while the flashlight is illuminated.

Caution

Fully discharge the battery before you begin a repair. A discharged battery is less susceptible to a battery thermal event. If you cant determine the battery level, dont repair the device.

Warning

Perform the following steps to discharge the battery:

To avoid noxious fumes or a battery thermal event, dont puncture, strike, or crush a lithium-ion battery or a device that contains one.

Keep your workspace clear of foreign objects and sharp materials. Be careful when using sharp tools near the battery. Dont leave loose screws, extra screws, or small parts inside the device. Dont use tools that conduct electricity. Dont throw or drop the battery. Dont expose the battery to excessive heat or sunlight, or temperatures outside the batterys

operating range. Handle and dispose of waste batteries in accordance with local laws and regulations.

Best practices

iPhone 12 Pro

073-00292-A | 18 2022 Apple Inc. All rights reserved.

Broken Glass

Broken Glass

Tools

Warning iPhone displays and some back covers are made of glass. The glass could break if the iPhone is dropped on a hard surface, receives a substantial impact, or is crushed, bent, or deformed. Dont attempt to remove chipped or cracked glass shards.

If the iPhone glass is broken, perform the following steps before you begin a repair:

1. Put on safety glasses with side shields and the cut-resistant gloves. 2. Use a vacuum cleaner to remove glass pieces from your workspace and the iPhone. 3. Attach a protective cover to the broken glass to prevent injury or scattering of glass. Each protective

cover has a release liner underneath. Slowly pull the release liner out from under the protective cover while pressing the cover onto the enclosure.

4. Fold the release liner. Use the shiny side of the release liner to firmly press the protective cover onto the broken glass and smooth out any air bubbles.

5. Wait at least 12 minutes for the bond between the protective cover and the glass to strengthen. 6. If the back glass is broken, place the iPhone into the heated display pocket.

Back protective cover Cut-resistant gloves Display protective cover Heated display pocket Safety glasses with side shields Vacuum cleaner

iPhone 12 Pro

073-00292-A | 19 2022 Apple Inc. All rights reserved.

Broken Glass

If the iPhone has any of the following conditions, stop the repair:

Theres no glass or insufficient glass for the protective cover to adhere to. The protective cover doesnt adhere to the iPhone. The iPhone doesnt fit in the heated display pocket.

You can find a service option at support.apple.com/repair.

iPhone 12 Pro

073-00292-A | 20 2022 Apple Inc. All rights reserved.

First Steps

First Steps

Always perform the following steps before starting a repair:

Back up the iPhone. Discharge the battery fully. Turn off the iPhone. Disconnect all cables. Remove all cases and covers. Clear and clean your workspace. Put on an ESD wrist strap and attach it to a properly grounded ESD mat.

Loose screws, extra screws, or small parts inside the device can damage the battery and cause safety issues. Set aside all parts and screws removed during the repair and account for them at the end of the repair.

ESD (electrostatic discharge, or the release of static electricity) can damage electronic components.

Warning

Caution

Be aware of the following while performing a repair:

The manual for this model may show images of other models, but the procedures are the same. Ensure that you use the correct tools for the model youre repairing.

Take your time. Thoroughly read all instructions and alerts. Magnetizing the torque drivers will make it easier to work with small screws. The end of each flex cable must align with its connector. Press the end of each flex cable to its

connector until it clicks to ensure that its secure.

iPhone 12 Pro

073-00292-A | 21 2022 Apple Inc. All rights reserved.

SIM Tray

SIM-eject tool or paper clip

SIM Tray

Tools

Removal

1. Find your model to locate the SIM tray.

2. Insert a paper clip or SIM-eject tool into the hole next to the SIM tray.

3. Push the paper clip or SIM-eject tool toward the enclosure to eject the SIM tray.

4. Remove the SIM tray.

Reassembly

1. Press the SIM tray back into the side of the enclosure.

iPhone 12 Pro

073-00292-A | 22 2022 Apple Inc. All rights reserved.

6.1-inch heated display pocket 6.1-inch repair tray Adhesive cutter Display adhesive press plate Display press ESD-safe tweezers Ethanol wipes or isopropyl alcohol (IPA) wipes Heated display removal fixture Heat-resistant gloves Micro stix bit Nylon probe (black stick) Torque driver (black, 0.35 kgf cm) Torque driver (gray, 0.55 kgf cm) Torx security bit

Display

Tools

Read Battery Safety and follow workspace and battery handling guidelines before you begin. Read Broken Glass before you begin.

Warning

Display | Before You Begin

Before You Begin

iPhone 12 Pro

073-00292-A | 23 2022 Apple Inc. All rights reserved.

Caution To avoid damaging

the lenses, dont touch the TrueDepth camera assembly or nearby parts.

Dont touch the back of the display. Touching the back of the display may affect image quality.

This procedure requires System Configuration. After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Read Heated Display Removal Fixture if youre setting up the fixture for the first time.

Important

Display | Before You Begin

iPhone 12 Pro

073-00292-A | 24 2022 Apple Inc. All rights reserved.

Removal

1. Use a torque driver and the Torx security bit to remove the two security screws, one from each side of the Lightning connector. Set aside the screws.

2. Flip the switch on the back of the heated display removal fixture to turn it on. The internal fan will turn on. Wait for a checkmark to appear on the screen.

Display | Removal

Note: If an error code appears on the screen, turn off the fixture and turn it back on.

iPhone 12 Pro

073-00292-A | 25 2022 Apple Inc. All rights reserved.

3. Gently insert the iPhone into the heated display pocket with the display faceup and the Lightning connector facing the bottom of the pocket.

4. Flip down the clamp on the side of the pocket to lock the iPhone into place.

Display | Removal

Ensure that the clamp on the side of the pocket is flipped up.

Important

iPhone 12 Pro

073-00292-A | 26 2022 Apple Inc. All rights reserved.

5. Put on the heat-resistant gloves. Align the cutout on the bottom of the pocket with the rail on the fixture. Slide the pocket with the iPhone onto the rail on the fixture.

Dont insert the pocket into the fixture without wearing the heat-resistant gloves.

Warning

Display | Removal

iPhone 12 Pro

073-00292-A | 27 2022 Apple Inc. All rights reserved.

6. Slide the pocket into the fixture until you hear the pocket click into place.

Note: The screen on the fixture will turn red and the timer will count down from 2 minutes while the pocket heats to the correct temperature. When the timer ends, the fixture will start to beep and the screen will turn green.

Display | Removal

iPhone 12 Pro

073-00292-A | 28 2022 Apple Inc. All rights reserved.

7. Turn the knob on the fixture clockwise to lower the suction cup as close to the iPhone as possible without touching the iPhone.

Note: The fixture will beep until the suction cup is lowered.

8. Grasp the handle and slide the suction cup straight out until the edge of the suction cup aligns with the bottom edge of the display.

Caution Failure to align the edges of the suction cup and the display may damage the iPhone.

Caution To avoid damaging the iPhone, dont turn the knob before the timer beeps.

Display | Removal

iPhone 12 Pro

073-00292-A | 29 2022 Apple Inc. All rights reserved.

Display | Removal

9. Turn the knob on the fixture clockwise to lower the suction cup onto the display (1). Then flip down the handle on the suction cup to secure the suction cup to the display (2).

10. Slowly turn the knob on the fixture counterclockwise until the display begins to separate from the enclosure.

If you dont see a gap between the display and the enclosure immediately, wait 30 seconds. If you still dont see a gap, turn the silver part of the knob counterclockwise until the display begins to separate from the enclosure.

Important

iPhone 12 Pro

073-00292-A | 30 2022 Apple Inc. All rights reserved.

11. Insert the edge of the adhesive cutter between the display and the enclosure. Run the cutter between the display and the enclosure to the right and left as shown until the display partially releases from the enclosure.

Caution To avoid damaging the flex cables, dont tilt up the bottom of the display more than 5 degrees.

Display | Removal

iPhone 12 Pro

073-00292-A | 31 2022 Apple Inc. All rights reserved.

12. Flip up the handle to release the suction cup (1). Gently slide the flat end of the black stick under the edge of the suction cup to release it from the display (2).

13. Press the eject button on the side of the pocket to release the pocket from the fixture.

Caution Dont turn the knob. Turning the knob may damage the flex cables.

Display | Removal

iPhone 12 Pro

073-00292-A | 32 2022 Apple Inc. All rights reserved.

14. Hold both sides of the pocket and slide it straight out of the fixture.

15. Flip up the clamp on the side of the pocket to release the iPhone (1). Hold the area outlined in blue and gently remove the iPhone from the pocket (2).

Display | Removal

16. Place the iPhone into the repair tray with the display faceup and the Lightning connector facing the cutout. Remove the gloves.

iPhone 12 Pro

073-00292-A | 33 2022 Apple Inc. All rights reserved.

17. Slide the display slightly toward the bottom of the iPhone.

18. Insert the edge of the adhesive cutter into the top of the iPhone between the display and the enclosure. Hold the adhesive cutter at a 45-degree angle. Start at the middle and cut along the top and sides of the iPhone until the display is free.

To avoid damaging the flex cables, dont tilt up the bottom of the display more than 5 degrees.

Caution

Display | Removal

iPhone 12 Pro

073-00292-A | 34 2022 Apple Inc. All rights reserved.

19. Insert the repair tray suction cups into the slots in the repair tray.

20. Tilt up the display toward the suction cups. Press the top and bottom edges of the display to secure it to the suction cups.

Caution To avoid damaging the

enclosure or display, ensure that the internal display clips are released before you tilt up the display.

Dont damage the flex cables as you tilt up the display.

Display | Removal

If the battery is dented, punctured, or otherwise damaged, stop the repair. You can find a service option at support.apple.com/repair.

Warning

iPhone 12 Pro

073-00292-A | 35 2022 Apple Inc. All rights reserved.

21. Use a torque driver and the Micro stix bit to remove the two trilobe screws from the lower cowling. Set aside the screws.

22. Use ESD-safe tweezers to remove the lower cowling. Save the cowling for reassembly.

Display | Removal

iPhone 12 Pro

073-00292-A | 36 2022 Apple Inc. All rights reserved.

25. Use ESD-safe tweezers to remove the upper cowling. Save the cowling for reassembly.

23. Use a torque driver and the Micro stix bit to remove three trilobe screws from the upper cowling. Set aside the screws.

24. Hold the upper cowling in place and use a torque driver and the Micro stix bit to remove the last trilobe screw. Set aside the screw.

Display | Removal

iPhone 12 Pro

073-00292-A | 37 2022 Apple Inc. All rights reserved.

26. Use the black stick to lift the end of the battery flex cable off the connector.

27. Use the black stick to lift the end of the display flex cable off the connector.

Display | Removal

Caution You must disconnect the battery flex cable first to ensure that the iPhone remains turned off.

iPhone 12 Pro

073-00292-A | 38 2022 Apple Inc. All rights reserved.

28. Use the black stick to lift the end of the Multi-Touch flex cable off the connector.

29. Use the black stick to lift the end of the receiver flex cable off the connector.

30. Hold the display by the edges. Pull the tabs on the suction cups to release them from the display. Then set the display facedown on a clean, flat surface.

Display | Removal

iPhone 12 Pro

073-00292-A | 39 2022 Apple Inc. All rights reserved.

32. Use ESD-safe tweezers to pick up the adhesive. Then pull the adhesive to remove it from the enclosure. Repeat this process until all the adhesive is removed from the perimeter of the enclosure.

Dont touch the TrueDepth camera assembly, grounding springs, or nearby parts.

Caution

31. Remove the suction cups from the repair tray.

Display | Removal

iPhone 12 Pro

073-00292-A | 40 2022 Apple Inc. All rights reserved.

33. Use ethanol wipes or IPA wipes to clean any adhesive residue from the enclosure.

Dont use ethanol wipes or IPA wipes on the display. Ethanol or isopropyl alcohol may damage the display and affect image quality.

Caution

Display | Removal

iPhone 12 Pro

073-00292-A | 41 2022 Apple Inc. All rights reserved.

Reassembly

1. Inspect the internal display clips for damage before reassembly. Ensure that the internal display clips are at a 90-degree angle and arent bent or damaged.

2. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Display | Reassembly

If the internal display clips are damaged, you may need to replace the display.

If youre installing a replacement display, peel the protective liner from the top and underside of it.

Important

iPhone 12 Pro

073-00292-A | 42 2022 Apple Inc. All rights reserved.

3. Inspect the TrueDepth camera. Ensure that the top edge of the TrueDepth camera is under the lip of the enclosure.

Correct position Incorrect position

If the TrueDepth camera is positioned incorrectly, use the black stick to move it away from the grounding clip. Then insert the top edge of the TrueDepth camera under the lip of the enclosure.

Caution

Display | Reassembly

Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

Warning

iPhone 12 Pro

073-00292-A | 43 2022 Apple Inc. All rights reserved.

5. The replacement display adhesive has a top release liner, a middle release liner, and a flexible bottom release liner. Grasp the tab on the bottom release liner. Then slowly pull the bottom release liner (1) out from under the adhesive (2) while pressing the adhesive onto the enclosure.

4. Align the replacement display adhesive over the enclosure with the top holes over the TrueDepth camera assembly and the bottom tab on the right.

Ensure that youve removed all adhesive residue from the display and the enclosure before you apply the replacement display adhesive.

Caution

Dont remove the top release liner yet.

Important

Display | Reassembly

Bottom release liner

Adhesive

Note: The replacement display adhesive for your model may look different from the illustration, but the steps are the same.

iPhone 12 Pro

073-00292-A | 44 2022 Apple Inc. All rights reserved.

6. Place the display adhesive press plate on top of the enclosure with the icon in the top right corner as shown.

Display | Reassembly

7. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

iPhone 12 Pro

073-00292-A | 45 2022 Apple Inc. All rights reserved.

8. Wait until the timer on the display press beeps. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

Display | Reassembly

iPhone 12 Pro

073-00292-A | 46 2022 Apple Inc. All rights reserved.

9. Remove the repair tray from the display press and remove the press plate.

10. Remove the left section of the top release liner first (1). Then remove the three sections running along the top (2), right (3), and bottom (4).

11. Insert the suction cups into the repair tray.

Dont remove the middle release liner yet.

Important

Display | Reassembly

Top release liner

iPhone 12 Pro

073-00292-A | 47 2022 Apple Inc. All rights reserved.

13. Press the ends of the receiver flex cable (1), Multi-Touch flex cable (2), and the display flex cable (3) to the connectors. Press evenly along the length of each connector.

15. Use ESD-safe tweezers to position the lower cowling over the ends of the Multi-Touch, display, and battery flex cables.

16. Use the black torque driver and Micro stix bit to install two new trilobe screws into the lower cowling.

12. Align the left edge of the display with the left edge of the enclosure as shown. Gently press along the edges of the display to secure it to the suction cups.

Display | Reassembly

14. Press the end of the battery flex cable to

the connector (4). Press evenly along the length of the connector.

Note: The display flex cable covers the Multi-Touch flex cable.

iPhone 12 Pro

073-00292-A | 48 2022 Apple Inc. All rights reserved.

19. Peel the first strip from the middle release liner (1) counterclockwise, starting near the bottom of the right of the enclosure. Peel the second strip (2) clockwise, starting near the bottom right of the enclosure. Peel the third strip (3) counterclockwise, starting near the top left of the enclosure.

18. Use the black torque driver and Micro stix bit to install four new trilobe screws into the upper cowling in the order shown.

17. The upper cowling has a tab near the second screw hole (2) that fits into a slot near the camera cowling. Use ESD-safe tweezers to fit the tab into the slot. Then lower the cowling over the end of the receiver flex cable.

Display | Reassembly

Middle release liner

iPhone 12 Pro

073-00292-A | 49 2022 Apple Inc. All rights reserved.

20. Inspect the display adhesive to ensure that its in the correct position and not damaged or wrinkled. If the adhesive is damaged, remove it and apply replacement adhesive.

21. Repeat step 3 to ensure that the TrueDepth camera is in the correct position. Then continue to step 22.

22. Pull the tabs on the suction cups to release them from the display. Tilt down the display to rest on the enclosure.

23. Remove the suction cups from the repair tray.

Display | Reassembly

Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

Warning

iPhone 12 Pro

073-00292-A | 50 2022 Apple Inc. All rights reserved.

24. Press all four corners of the display simultaneously. Then press along the edges of the display until you hear a click and the display is flush with the enclosure.

Ensure that the flex cables arent trapped between the display and the enclosure. Feel the edges of the display for variations or gaps. If the display isnt flush, repeat all removal steps and check the flex cables for damage. Then repeat reassembly steps 1 through 24.

Caution

Display | Reassembly

iPhone 12 Pro

073-00292-A | 51 2022 Apple Inc. All rights reserved.

25. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

Display | Reassembly

26. Wait until the timer on the display press beeps. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

iPhone 12 Pro

073-00292-A | 52 2022 Apple Inc. All rights reserved.

27. Remove the repair tray from the display press.

28. Use the gray torque driver and Torx security bit to install two new security screws, one on each side of the Lightning connector. As you install the screws, press lightly on the display near the Lightning connector.

If the screws arent flush, remove and set aside the screws. Repeat step 28 to install another new set of screws. If the new screws still arent flush, repeat all removal and reassembly steps.

Caution

System Configuration is required if youve installed a replacement display, battery, or camera. Disregard notifications about iPhone features on the Lock Screen until you complete System Configuration.

After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

Display | Reassembly

iPhone 12 Pro

073-00292-A | 53 2022 Apple Inc. All rights reserved.

Camera

6.1-inch repair tray ESD-safe tweezers Micro stix bit Nitrile or lint-free gloves Nylon probe (black stick) Torque driver (black, 0.35 kgf cm)

Tools

Display

Remove the following part before you begin:

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Warning

Camera | Before You Begin

Before You Begin

Caution To avoid damaging the

lenses, dont touch the TrueDepth camera assembly or nearby parts.

Avoid the grounding springs on the camera cowling and enclosure.

This procedure requires System Configuration. After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

iPhone 12 Pro

073-00292-A | 54 2022 Apple Inc. All rights reserved.

Removal

2. Use a torque driver and the Micro stix bit to remove the four trilobe screws from the camera cowling in the order shown. Set aside the screws.

3. Use ESD-safe tweezers to tilt up the left side of the camera cowling as shown. Then slide the camera cowling out of the enclosure. Save the cowling for reassembly.

Camera | Removal

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

iPhone 12 Pro

073-00292-A | 55 2022 Apple Inc. All rights reserved.

4. Use ESD-safe tweezers to gently lift the end of the top camera flex cable off the connector.

5. Use ESD-safe tweezers to gently lift the end of the bottom camera flex cable off the connector.

Note: One camera flex cable covers the other.

Camera | Removal

6. Gently hold the flex cables together and lift the cameras out of the enclosure.

iPhone 12 Pro

073-00292-A | 56 2022 Apple Inc. All rights reserved.

1. Put on the gloves to prevent contamination of the camera lenses. Then hold the replacement cameras with the lenses facedown and remove the protective cover from the camera lenses.

2. Tilt down the cameras under the lip of the enclosure. Then lower the cameras into position.

Reassembly

3. Press the end of the bottom camera flex cable to the connector.

4. Press the end of the top camera flex cable to the connector.

5. Lightly press the cameras into the enclosure.

Camera | Reassembly

iPhone 12 Pro

073-00292-A | 57 2022 Apple Inc. All rights reserved.

6. The camera cowling has tabs that fit into slots under the lip on the right side of the enclosure. Inspect the tabs and grounding spring on the cowling for damage before reassembly.

Caution

Camera | Reassembly

7. Hold the cowling with ESD-safe tweezers and slide the cowling tabs into the slots. Then lower the cowling onto the cameras.

Avoid touching the grounding spring as you reinstall the camera cowling.

Ensure that the screw cutouts in the camera cowling align with the screw holes. A misaligned camera cowling may affect display image quality.

iPhone 12 Pro

073-00292-A | 58 2022 Apple Inc. All rights reserved.

Display

Reinstall the following part to complete reassembly:

8. Use the black torque driver and Micro stix bit to install four new trilobe screws into the camera cowling in the order shown.

After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

Camera | Reassembly

iPhone 12 Pro

073-00292-A | 59 2022 Apple Inc. All rights reserved.

During System Configuration, you will perform LiDAR Scanner calibration. Prepare for calibration by reviewing the following steps:

1. Use a well-lit area containing objects of different shapes and sizes.

2. Sit or stand 1 to 2 feet from the objects.

3. Hold the device vertically and rest your elbow on your body to help stabilize your arm.

4. Start scanning by slowly panning back and forth to the left and right of the starting point. Follow the directions that appear on the device screen.

Note: The calibration process takes approximately 5 minutes.

Camera | Reassembly

iPhone 12 Pro

073-00292-A | 60 2022 Apple Inc. All rights reserved.

Speaker

6.1-inch repair tray ESD-safe tweezers JCIS bit Nylon probe (black stick) Torque driver (green, 0.45 kgf cm)

Tools

Display

Remove the following part before you begin:

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Warning

Speaker | Before You Begin

Before You Begin

iPhone 12 Pro

073-00292-A | 61 2022 Apple Inc. All rights reserved.

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Removal

2. Use a torque driver and the JCIS bit to remove the four crosshead screws from the speaker. Set aside the screws.

3. Use the black stick to tilt up the speaker. Then remove the speaker from the enclosure.

Speaker | Removal

iPhone 12 Pro

073-00292-A | 62 2022 Apple Inc. All rights reserved.

1. Rotate the repair tray. Ensure that the rubber gasket is positioned as shown. If the gasket is out of position, use ESD-safe tweezers to reposition it.

Reassembly

Speaker | Reassembly

iPhone 12 Pro

073-00292-A | 63 2022 Apple Inc. All rights reserved.

2. Rotate the repair tray. Tilt down the speaker and lower it into position.

Dont damage the grounding springs on the speaker.

Caution

3. Use the green torque driver and JCIS bit to install four new crosshead screws into the speaker.

Display

Reinstall the following part to complete reassembly:

Speaker | Reassembly

iPhone 12 Pro

073-00292-A | 64 2022 Apple Inc. All rights reserved.

Battery

6.1-inch repair tray Battery press ESD-safe cleaning solution ESD-safe tweezers Ethanol wipes or isopropyl alcohol (IPA) wipes Heat-resistant gloves Nitrile or lint-free gloves Nylon probe (black stick) Safety glasses with side shields Sand Sand container Super screw bit Torque driver (gray, 0.55 kgf cm)

Tools

A battery should be replaced only by individual technicians with the knowledge and experience to repair electronic devices. Improper battery replacement, improper handling of parts, or failure to follow the provided instructions could result in fire, injury, data loss, or damage to the device, parts, or other property.

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Warning

Battery | Before You Begin

Before You Begin

Display Speaker

Remove the following parts before you begin:

iPhone 12 Pro

073-00292-A | 65 2022 Apple Inc. All rights reserved.

To avoid damaging the lenses, dont touch the TrueDepth camera assembly or nearby parts.

Caution

This procedure requires System Configuration. After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

Battery | Before You Begin

iPhone 12 Pro

073-00292-A | 66 2022 Apple Inc. All rights reserved.

1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Use a torque driver and the screw super bit to remove the super screw from the upper right corner of the Taptic Engine. Set aside the screw.

Removal

Battery | Removal

iPhone 12 Pro

073-00292-A | 67 2022 Apple Inc. All rights reserved.

3. Use ESD-safe tweezers to grasp the bottom right battery adhesive tab. Gently peel the adhesive tab away from the battery.

Note: The battery has four adhesive tabs.

Battery | Removal

Dont scrape or puncture the battery with the tweezers.

Warning

iPhone 12 Pro

073-00292-A | 68 2022 Apple Inc. All rights reserved.

4. Hold down the iPhone. Use ESD-safe tweezers to continue peeling the battery adhesive tab from the battery.

Peel the adhesive tab completely from the battery before twisting it around the tweezers.

Important

Battery | Removal

iPhone 12 Pro

073-00292-A | 69 2022 Apple Inc. All rights reserved.

5. Keep the tweezers close and parallel to the battery and twist until you see white adhesive strip on the tweezers.

Dont pull the tweezers until the white adhesive is wrapped around them.

Important

6. Pull the tweezers toward the bottom of the iPhone and continue to twist the adhesive strip until youve removed the entire strip.

Dont pull the adhesive strip against parts or screws.

Caution

If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat steps 5 and 6. If you cant see the tab or strip, continue to step 7.

Important

Battery | Removal

iPhone 12 Pro

073-00292-A | 70 2022 Apple Inc. All rights reserved.

8. Repeat steps 4 through 6 to remove the bottom left adhesive strip from the battery. If you remove the entire strip, continue to step 9.

9. Rotate the repair tray and put on the nitrile or lint-free gloves.

10. Use ESD-safe tweezers to gently peel the two battery adhesive tabs from the top of the battery.

7. Use ESD-safe tweezers to grasp the bottom left battery adhesive tab. Gently peel the adhesive tab away from the battery.

Important Pull the bottom left

adhesive strip away from the Taptic Engine.

If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat steps 5 and 6. If you cant see the tab or strip, continue to step 9.

Battery | Removal

iPhone 12 Pro

073-00292-A | 71 2022 Apple Inc. All rights reserved.

12. Keep the tweezers in the channel between the battery and the camera cowling. Continue to slowly twist the tweezers until youve removed the entire adhesive strip.

11. Hold down the iPhone. Use ESD-safe tweezers to grasp one battery adhesive tab. Then twist the tweezers to wrap the adhesive tab around them.

Hold the tweezers close and parallel to the battery as you twist.

Important

If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat step 12. If you cant see the tab or strip, continue to step 13.

Important

Battery | Removal

iPhone 12 Pro

073-00292-A | 72 2022 Apple Inc. All rights reserved.

13. Repeat steps 11 and 12 to remove the remaining battery adhesive strip from the top of the battery. If you remove the entire strip, continue to step 14.

If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat step 12. If you cant see the tab or strip, continue to step 14.

Important

14. If all four battery adhesive strips were fully removed, continue to step 16. If at least one strip was fully removed, continue to step 15.

If all four strips were broken and cant be retrieved, dont forcibly pry the battery. Stop the repair. You can find a service option at support.apple.com/repair.

Warning

Battery | Removal

iPhone 12 Pro

073-00292-A | 73 2022 Apple Inc. All rights reserved.

15. Insert the flat end of the black stick into one of the insertion points as shown. Ensure that the black stick is inserted into a point where the battery strip has been fully removed. Dont insert the black stick into a point where the battery tab or strip is broken.

When using the black stick to remove the battery from the enclosure, dont damage the flex cables. Dont scrape, rip, tear, or otherwise damage the polyester film or other areas. If damage occurs, replace the iPhone.

Caution

Battery | Removal

iPhone 12 Pro

073-00292-A | 74 2022 Apple Inc. All rights reserved.

16. Slightly lift the battery with the black stick just enough to grasp underneath the battery.

17. Remove the battery from the enclosure. Then inspect the enclosure for damage. If the enclosure is damaged, replace the iPhone.

To avoid damage, dont press the black stick on the edge of the enclosure as you lift the battery.

Caution

Battery | Removal

If you cant remove the battery, stop the repair. You can find a service option at support.apple.com/repair.

Warning

iPhone 12 Pro

073-00292-A | 75 2022 Apple Inc. All rights reserved.

1. Use the gray torque driver and super screw bit to install one new super screw into the upper right corner of the Taptic Engine.

3. Use ethanol wipes or IPA wipes on the area shown in blue to remove any remaining adhesive from the enclosure.

Reassembly

2. Reinstall the speaker.

Battery | Reassembly

Caution Dont use ethanol wipes or IPA wipes on the areas outlined in red. Ethanol or isopropyl alcohol may damage the polyester film and wireless charging unit.

Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

Warning

iPhone 12 Pro

073-00292-A | 76 2022 Apple Inc. All rights reserved.

5. Hold the battery over the enclosure with the protective cover faceup. Align the bottom of the battery with the speaker (1) and the left edge with the logic board (2). Then lower the battery into the enclosure.

4. Peel the pink release liner from the underside of the replacement battery.

Dont remove the battery protective cover from the top of the battery yet.

Important

Battery | Reassembly

iPhone 12 Pro

073-00292-A | 77 2022 Apple Inc. All rights reserved.

6. Place the repair tray and the enclosure into the battery press. The repair tray has a cutout at the bottom and two slots in the center. Align the left slot on the repair tray with the pin on the battery press.

7. Flip down the red lever to lower the roller onto the battery.

Battery | Reassembly

iPhone 12 Pro

073-00292-A | 78 2022 Apple Inc. All rights reserved.

8. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.

9. Flip up the red lever.

Battery | Reassembly

iPhone 12 Pro

073-00292-A | 79 2022 Apple Inc. All rights reserved.

10. Align the right slot on the repair tray with the pin on the battery press.

11. Flip down the red lever.

Battery | Reassembly

iPhone 12 Pro

073-00292-A | 80 2022 Apple Inc. All rights reserved.

12. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.

13. Flip up the red lever.

Battery | Reassembly

iPhone 12 Pro

073-00292-A | 81 2022 Apple Inc. All rights reserved.

Display

Reinstall the following part to complete reassembly:

Gently shake the iPhone. If the battery sounds loose, remove the display and the battery. Then complete battery reassembly with another replacement battery.

Warning

14. Remove the repair tray from the battery press.

15. Hold the edges of the protective cover. Pull the release tabs on the protective cover to remove the cover from the battery.

Dont press the area over the tab you are releasing.

Important

After youve completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

Important

Battery | Reassembly

iPhone 12 Pro

073-00292-A | 82 2022 Apple Inc. All rights reserved.

Taptic Engine

6.1-inch repair tray ESD-safe tweezers JCIS bit Micro stix bit Nylon probe (black stick) SIM-eject tool Super screw bit Torque driver (black, 0.35 kgf cm) Torque driver (gray, 0.55 kgf cm) Torque driver (green, 0.45 kgf cm)

Tools

Display Speaker

Remove the following parts before you begin:

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Warning

Taptic Engine | Before You Begin

Before You Begin

iPhone 12 Pro

073-00292-A | 83 2022 Apple Inc. All rights reserved.

1. Remove the enclosure from the repair tray.

4. Use a torque driver and the Micro stix bit to remove the two trilobe screws from the SIM reader connector cowling. Set aside the screws.

Removal

2. Remove the SIM tray.

3. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

5. Use ESD-safe tweezers to remove the SIM reader connector cowling. Save the cowling for reassembly.

Taptic Engine | Removal

iPhone 12 Pro

073-00292-A | 84 2022 Apple Inc. All rights reserved.

6. Use a torque driver and the Micro stix bit to remove the two trilobe screws from the Taptic Engine connector cowling. Set aside the screws.

8. Use ESD-safe tweezers to lift the end of the SIM reader flex cable off the connector.

7. Use ESD-safe tweezers to remove the Taptic Engine connector cowling. Save the cowling for reassembly.

Taptic Engine | Removal

iPhone 12 Pro

073-00292-A | 85 2022 Apple Inc. All rights reserved.

10. Use a torque driver and the super screw bit to remove the super screw from the lower right corner of the SIM reader. Set aside the screw.

9. Use a torque driver and the Micro stix bit to remove the trilobe screw from the upper left corner of the SIM reader. Set aside the screw.

Taptic Engine | Removal

iPhone 12 Pro

073-00292-A | 86 2022 Apple Inc. All rights reserved.

11. Tilt up the SIM reader and lift it out of the enclosure.

12. Use a torque driver and the super screw bit to remove the two super screws from the corners of the Taptic Engine. Set aside the screws.

Taptic Engine | Removal

iPhone 12 Pro

073-00292-A | 87 2022 Apple Inc. All rights reserved.

14. Use ESD-safe tweezers to lift the end of the Taptic Engine flex cable off the connector.

15. Use ESD-safe tweezers to remove the Taptic Engine.

13. Use a torque driver and the JCIS bit to remove the crosshead screw from the bottom of the Taptic Engine. Set aside the screw.

Taptic Engine | Removal

iPhone 12 Pro

073-00292-A | 88 2022 Apple Inc. All rights reserved.

1. Position the Taptic Engine in the enclosure.

Reassembly

2. Press the end of the Taptic Engine flex cable to the connector.

Taptic Engine | Reassembly

iPhone 12 Pro

073-00292-A | 89 2022 Apple Inc. All rights reserved.

4. Use the gray torque driver and super screw bit to install two new super screws into the Taptic Engine.

3. Use the green torque driver and JCIS bit to install one new crosshead screw into the Taptic Engine.

Taptic Engine | Reassembly

iPhone 12 Pro

073-00292-A | 90 2022 Apple Inc. All rights reserved.

5. Tilt the SIM reader into the enclosure.

6. Use the black torque driver and Micro stix bit to install one new trilobe screw into the upper left corner of the SIM reader.

Taptic Engine | Reassembly

iPhone 12 Pro

073-00292-A | 91 2022 Apple Inc. All rights reserved.

7. Use the gray torque driver and super screw bit to install one new super screw into the lower right corner of the SIM reader.

8. Press the end of the SIM reader flex cable to the connector.

Taptic Engine | Reassembly

iPhone 12 Pro

073-00292-A | 92 2022 Apple Inc. All rights reserved.

9. Position the SIM reader connector cowling (1) over the end of the flex cable.

Inspect the grounding spring on the Taptic Engine connector cowling to ensure that its not damaged.

Caution

Taptic Engine | Reassembly

10. Position the Taptic Engine connector cowling (2) over the end of the flex cable.

iPhone 12 Pro

073-00292-A | 93 2022 Apple Inc. All rights reserved.

13. Reinstall the SIM tray.

Reinstall

Manualsnet FAQs

If you want to find out how the iPhone 12 Pro Apple works, you can view and download the Apple iPhone 12 Pro Smartphone Repair Manual on the Manualsnet website.

Yes, we have the Repair Manual for Apple iPhone 12 Pro as well as other Apple manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Repair Manual should include all the details that are needed to use a Apple iPhone 12 Pro. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Apple iPhone 12 Pro Smartphone Repair Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Apple iPhone 12 Pro Smartphone Repair Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Apple iPhone 12 Pro Smartphone Repair Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Apple iPhone 12 Pro Smartphone Repair Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Apple iPhone 12 Pro Smartphone Repair Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.