Contents

Apple Xserve RAID v9 Replacement Instructions PDF

1 of 11
1 of 11

Summary of Content for Apple Xserve RAID v9 Replacement Instructions PDF

073-0750 Rev. A

!

Xserve RAID

Left or Right Front Light Pipe

Replacement Instructions

Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void its warranty.

Online instructions covering customer-installable parts are available at http://www.info.apple.com/installparts/.

Important:

Due to the weight of the Xserve RAID unit, two people are necessary for moving it out of or into a rack. Do not attempt to lift or move the system without help from another person.

Tools Required

The only tools required for this procedure are a Phillips screwdriver and a small at-blade screwdriver.

Opening Xserve RAID

To open Xserve RAID, you must rst shut down the system and remove the unit from its rack.

1. Alert users that the Xserve RAID drives will be unavailable for a period of time.

2. If the unit is in the locked position (the yellow security LED on the front panel is on), use the Allen key that came with the system to unlock it.

3. Shut down the system.

Warning: After you shut down Xserve RAID, internal components can be very hot. Let the unit cool down a few minutes before continuing.

4. Unplug all external cables except the power cords.

5. Touch the Xserve RAID metal case to discharge static electricity.

Important:

Always ground yourself by touching the case before you touch any parts or install any components inside the unit. To avoid static electricity building back up in your body, do not walk around the room until you have completed your work and closed the unit.

6. Unplug the power cords.

Xserve RAID Left or Right Front Light Pipe -

2

7. Remove the two screws that secure the system to the front rail of the rack.

(Figure 1)

Figure 1

8. Remove the two screws that secure the back of the systems side panels to the rack.

9. With one person supporting each side of the unit, slide the system out of the rack and place it on a sturdy, at surface covered by an ESD mat.

10. Put on an ESD wrist strap.

11. Remove the 16 mounting screws on the left and right sides of the top cover.

(Figure 2)

Figure 2

12. Slide the top cover a short distance toward the back of the unit.

13. Lift the top cover straight up off the enclosure.

Xserve RAID Left or Right Front Light Pipe -

3

Removing the Installed Left or Right Front Light Pipe

The left and right front light pipes are located beneath the left and right front panel boards on the inside of the front bezel. This kit includes a light pipe that will t under either the left or right board. To replace the light pipe, you must rst remove the bezel and board.

1. Disconnect the locking cable and front panel cable from the front bezels right front panel board.

(Figure 3)

2. Disconnect the front panel cable from the bezels left front panel board.

3. Remove the four screws securing the bezel to the enclosure.

Figure 3

Xserve RAID Left or Right Front Light Pipe -

4

4. Carefully pull the bezel a short distance straight back off the enclosure, making sure the bezel clears the barrel of the locking mechanism.

(Figure 4)

Figure 4

5. Disconnect the front panel cable from the center front panel board.

(Figure 5)

6. Remove the bezel from the enclosure.

Figure 5

Xserve RAID Left or Right Front Light Pipe -

5

7. Place the bezel on an ESD mat with the left and right front panel boards facing up.

8. Remove the mounting screw on the left or right front panel board.

(Figure 6)

9. Remove the board from the bezel.

Figure 6

L

Left Front Panel Board

Right Front Panel Board

Xserve RAID Left or Right Front Light Pipe -

6

10. Using a at-blade screwdriver, carefully pry up the light pipe and shield.

(Figure 7)

11. Remove the light pipe and shield from the bezel.

Figure 7

Light Pipe Behind Left Front Panel Board

Light Pipe Behind Right Front Panel Board

Xserve RAID Left or Right Front Light Pipe -

7

Installing the Replacement Left or Right Front Light Pipe

1. Position the replacement light pipe in the left or right channel on the inside of the front bezel.

Note:

The light pipe comes with a black plastic shield.

(Figure 8)

Make sure the shield is in correct position over the light pipe before you place the light pipe into the bezel.

Figure 8

2. Position the left or right front panel board over the light pipe.

3. Replace the screw that secures the board to the bezel.

4. Connect the bottom connector on the front panel cable to the bezels center front panel board.

Xserve RAID Left or Right Front Light Pipe -

8

5. Route the two branches of the front panel cable straight up through the opening in the center front of the chassis.

(Figure 9)

Figure 9

6. Replace the bezel on the front of the enclosure, making sure the opening in the bezel ts over the barrel of the locking mechanism.

7. Replace the four screws that secure the bezel to the enclosure.

8. Connect the front panel cable to the left front panel board.

9. Connect the locking cable and front panel cable to the right front panel board.

Xserve RAID Left or Right Front Light Pipe -

9

Closing Xserve RAID

1. Place the cover on top of the enclosure so that it is approximately 1/4 inch back from the front bezel.

(Figure 10)

Note:

The left and right sides of the cover should fit inside the enclosure.

2. Slide the cover forward so that the two tabs on the front of the cover engage with the slots in the bezel.

Note:

Make sure that the screw holes in the cover and sides of the enclosure align.

Figure 10

3. Replace the 16 mounting screws on the left and right sides of the cover.

Xserve RAID Left or Right Front Light Pipe -

10

4. With one person supporting each side of the unit, slide it all the way into the rack until the unit engages the small posts at the rear of the L-brackets.

(Figure 11)

Figure 11

5. Replace the two screws that secure the unit to the front rail of the rack.

6. Reconnect all cables and power cords.

Warning: Never turn on Xserve RAID unless all of its internal and external parts are in place and it is closed. Operating the system when it is open or missing parts can damage it or cause injury.

Xserve RAID Left or Right Front Light Pipe -

11

!

Apple Computer, Inc.

2003 Apple Computer, Inc. All rights reserved.

This document is protected under U.S. Copyright Law and International Treaties, and no part of this document may be reproduced in any form without written permission from Apple.

Apple is not responsible for typographical, printing, or inadvertent errors.

Apple Compu

Manualsnet FAQs

If you want to find out how the Xserve RAID Apple works, you can view and download the Apple Xserve RAID v9 Replacement Instructions on the Manualsnet website.

Yes, we have the Replacement Instructions for Apple Xserve RAID as well as other Apple manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Replacement Instructions should include all the details that are needed to use a Apple Xserve RAID. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Apple Xserve RAID v9 Replacement Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Apple Xserve RAID v9 Replacement Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Apple Xserve RAID v9 Replacement Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Apple Xserve RAID v9 Replacement Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Apple Xserve RAID v9 Replacement Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.