Contents

Apple Xserve or Xserve G5 v3 Replacement Instructions PDF

1 of 8
1 of 8

Summary of Content for Apple Xserve or Xserve G5 v3 Replacement Instructions PDF

073-0756 Rev. C

Xserve/Xserve G5

Light Pipe Assembly

Replacement Instructions

Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void its warranty.

Note:

Online instructions covering customer-installable parts are available at http://www.info.apple.com/installparts/.

Note:

These instructions apply to the light pipe assembly of different versions of Xserve/ Xserve G5. While your server may look slightly different from the one shown in the illustrations, the procedures for all versions are the same.

Tools Required

The only tools required for Version 1 of this procedure are a Phillips screwdriver and a at- blade screwdriver. No tools are required for Version 2 of this procedure.

Opening the Server

The server slides open from the front of the rack. The top cover remains in place in the rack while the bottom housing (containing all internal components) should be placed on a sturdy, at surface.

1. Alert users that the server will be unavailable for a period of time.

2. Shut down the server.

Warning: To avoid damaging internal components or causing injury, always shut down the server before opening it. After you shut down the server, internal components can be very hot. Let the server cool down before continuing.

3. Write down the servers serial number, which is located on the back panel. If it is necessary to set up the servers software after you replace the light pipe assembly, you will be asked for the serial number at login.

Xserve/Xserve G5 Light Pipe Assembly -

2

4. If the server is in the locked position (the yellow security LED on the front panel is on), use the Allen key that came with the server to unlock it.

5. If the cable management arm is not in use, unplug all external cables except the power cord.

6. Touch the servers metal case to discharge any static electricity.

Important:

Always ground yourself by touching the servers case before you touch any parts or install any components inside the server. To avoid static electricity building back up in your body, do not walk around the room until you have completed your work and closed the computer.

7. Unplug the power cord.

Warning: The power supply in the server is a high-voltage component and should not be opened for any reason, even when the server is off.

8. Release the two thumbscrews at the front of the server.

(Figure 1)

Note:

The thumbscrews are captive and do not separate from the bottom housing.

Figure 1

Xserve/Xserve G5 Light Pipe Assembly -

3

9. Grasp the thumbscrews and slide the bottom housing forward part way to expose the two chassis levers.

(Figure 2)

10. While depressing both levers (1), pull the bottom housing all the way forward (2) and remove it from the rack.

Figure 2

11. Place the bottom housing on a sturdy, at surface and ESD mat.

12. Put on the ESD wrist strap.

Note:

There are two versions of Xserve, each of which requires a different procedure for replacing the light pipe assembly. To identify the versions, check the servers front bezel. If the bezel includes a slot for the optical drive, follow instructions for Version 1. If there is no slot in the bezel, follow Version 2 instructions.

Xserve/Xserve G5 Light Pipe Assembly -

4

Removing the Installed Light Pipe Assembly, Version 1

1. Using a Phillips screwdriver, remove the screws that attach the two front bezel brackets to the server, and remove the brackets.

(Figure 3)

2. Remove the screw that attaches the top of the bezel to the server.

Figure 3

3. Gently pull the front bezel forward and remove it from the server.

(Figure 4)

Important:

When removing or replacing the bezel, be careful not to put pressure on the top of the bezel over the optical drive slot.

Figure 4

Xserve/Xserve G5 Light Pipe Assembly -

5

4. Using a at-blade screwdriver, ease rst one side and then the other side of the light pipe assembly from its opening in the front of the enclosure.

(Figure 5)

5. Remove the light pipe assembly from the server.

Figure 5

Installing the Replacement Light Pipe Assembly, Version 1

1. Remove the bottom row of light pipes from the replacement assembly and insert them into the bottom row of light pipe holes in the front bezel.

(Figure 6)

Figure 6

Xserve/Xserve G5 Light Pipe Assembly -

6

2. Insert the rest of the replacement light pipe assembly into its opening in the front of the enclosure.

(Figure 7)

Figure 7

3. Replace the front bezel on the server, matching ports/projections with openings.

4. Replace the screw that secures the top of the bezel to the server.

5. Replace the two bezel brackets and their mounting screws.

Xserve/Xserve G5 Light Pipe Assembly -

7

Removing the Installed Light Pipe Assembly, Version 2

1. Release the two clips on the sides of the front panel board (1), and pull the board back (2) approximately 1.5 inches from the front of the server.

(Figure 8)

2. Remove the light pipe assembly from the server (3).

Figure 8

Installing the Replacement Light Pipe Assembly, Version 2

1. Position the replacement light pipe assembly against the inside front of the bezel, making sure the projections on the light pipes t into the holes in the bezel.

(Figure 9)

2. Slide the front panel board forward until it ts snugly against the assembly, and secure the two clips on the sides of the board.

Note:

You may need to lift the assembly slightly while sliding the front panel board, so that it doesnt catch the edge of the assembly.

Figure 9

Xserve/Xserve G5 Light Pipe Assembly -

8

Closing the Server

1. Carefully slide the bottom housing back into the rack.

2. Tighten the front thumbscrews to secure it.

Warning: Never turn on the server unless all of its internal and external parts are in place and it is closed. Operating the server when it is open or missing parts can damage it or cause injury.

Apple Computer, Inc.

2004 Apple Computer, Inc. All rights reserved.

This document is protected under U.S. Copyright Law and International Treaties, and no part of this document may be reproduced in any form without written permission from Apple.

Apple is not responsible for typographical, printing, or inadvertent errors.

Apple Computer, Inc. 1 Innite Loop Cupertino, CA 95014-2084 USA + 1 408 996 1010 http://www.apple.com

Apple, the Apple logo, Mac, Macintosh, and the Mac

Manualsnet FAQs

If you want to find out how the Xserve Apple works, you can view and download the Apple Xserve or Xserve G5 v3 Replacement Instructions on the Manualsnet website.

Yes, we have the Replacement Instructions for Apple Xserve as well as other Apple manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Replacement Instructions should include all the details that are needed to use a Apple Xserve. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Apple Xserve or Xserve G5 v3 Replacement Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Apple Xserve or Xserve G5 v3 Replacement Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Apple Xserve or Xserve G5 v3 Replacement Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Apple Xserve or Xserve G5 v3 Replacement Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Apple Xserve or Xserve G5 v3 Replacement Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.