Amcrest ASH26-W Security Camera Installation Guide PDF

1 of 2
1 of 2

Summary of Content for Amcrest ASH26-W Security Camera Installation Guide PDF

Installation Guide 1080p Floodlight Security Camera

For the most recent version of this Installation Guide visit: amcrest.com/oodlightsetup

1 What's Included

App Setup Guide

Floodlight Camera Mounting Plate

Mounting Screw

Hook

Wire Nuts Bracket Screws

Screws

Assembly

DOWN

FRONT

UP

BOTTOM

TOP

Junction Box (not included) Mounting Plate

Bracket Screws

Mounting Screw

Camera Lock Collar

NOTE Installation of the oodlight camera requires a junction box to cover exposed wiring.

GND

Application

The PIR sensor can detect human-sized objects up to 33 feet away, when mounted 10 feet off the ground with the PIR sensor parallel to the ground.

10ft (3m)

33ft (10m)

Floodlight Layout

The pattern of the LED indicator is included in the following table.

LED Indicator Status Device Status

Powered off/LED turned off Rebooting after reset

Booting Device malfunction

Waiting for network

Operating properly

Network connection failed

Firmware updating

Off

Red Light On

Green Light Flashing

Green Light On

Red Light Flashing

Green and Red Light Alternately Flashing

FloodlightFloodlight

Build-in Mic

Lens

LED Indicator

PIR Sensor

MicroSD Card Slot

Built-in Speaker

Light Sensor

Reset Button

NOTE To reset the camera press and hold the reset button for 10 seconds.2 3 4 7 865

WARNING WE HIGHLY RECOMMEND HIRING A LICENSED ELECTRICIAN IF YOU ARE NOT COMFORTABLE OR EXPERIENCED WITH THE TOOLS AND PROCESSES DESCRIBED IN THIS MANUAL. PLEASE ENSURE THE CIRCUIT BREAKER IS TURNED OFF AND YOU HAVE REVIEWED THE MANUAL IN ITS ENTIRETY BEFORE PROCEEDING.

Step 5

The copper wire from the camera is the ground (GND) wire. Run the ground wire from the camera through the designated ground screws on the mounting plate. Then connect the ground wire to the reserved ground wire in the junction box. Use the included wire nuts to connect the wires.

Step 6

Connect the power wires. The white wire from the camera is the neutral wire, connect this wire to the reserved neutral wire. The black wire from the camera is the hot (live) wire, connect this wire to the reserved hot wire.

Use the included wire nuts to connect the wires.

Step 7

Ensure all live wiring is covered. Feed all the wires into the junction box. Secure the camera to the mounting plate using the included mounting screw.

Step 8

Adjust the floodlights and camera lens to the desired angle. Keep the PIR detector parallel to the ground to ensure optimal detection.

Since we will be working with electrical wiring, it important to shut off the power to your floodlight at the electrical breakers of your home to ensure no power is flowing through the system.

TURN OFF THE CIRCUIT BREAKER

s

THIS GUIDE IS FOR INFORMATIONAL PURPOSES ONLY. WORKING WITH ELECTRICITY CAN BE DANGEROUS UNLESS PROPER SAFETY PRECAU- TIONS ARE TAKEN. WE RECOMMEND HIRING A LICENSED ELECTRICIAN IF YOU ARE NOT COMFORTABLE OR EXPERIENCED WITH THE TOOLS AND PROCESSES DESCRIBED IN THIS MANUAL.

DISCLAIMER

RISK OF ELECTRICAL SHOCK. We strongly suggest you hire a licensed electrician to install the camera. Be sure to disconnect the power at the fuse or circuit breaker before installation. Verify that the supply voltage is correct. Connect fixture to a 100 ~240VAC 50/60 Hz power source. Properly ground fixture. Always follow code standards when installing wired connection.

WARNING

RISK OF FIRE Do not connect near combustible or flammable surfaces.

Do not connect this light fixture to a dimmer switch or timer. Make sure the mounting surface is strong enough to hold at least three times the weight of the device.

Step 2 Attach the included mounting plate to the junction box.

Step 1 Turn the power off at the breaker. Remove any existing hard- ware from your junction box and disconnect any wires. Inspect the junction box to make sure water cannot get into it.

If you do not have an installed junction box, we highly recommended you hire a licensed electrician to complete the installation of your camera. Be sure to comply with your local codes.WARNING

Installing the Floodlight Step 3 Loosen the adjustment knobs located at the base of your flood- lights. Then, adjust the angle of the floodlights to make space for the mounting screwhole located between the camera and floodlights.

Step 4 Attach one end of the hook to the mounting plate, and the other end to the edge of the camera so you can free your hands for installation.

Now its time to setup the Amcrest Smart Home App. To connect your Amcrest Floodlight camera to your Android or iOS mobile device, download the Amcrest Smart Home app, then follow the instructions in included the App Setup Guide.

Online Video Tutorial & Quick Start Guide amcrest.com/oodlightsetup

Need help? su

Manualsnet FAQs

If you want to find out how the ASH26-W Amcrest works, you can view and download the Amcrest ASH26-W Security Camera Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Amcrest ASH26-W as well as other Amcrest manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Amcrest ASH26-W. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Amcrest ASH26-W Security Camera Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Amcrest ASH26-W Security Camera Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Amcrest ASH26-W Security Camera Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Amcrest ASH26-W Security Camera Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Amcrest ASH26-W Security Camera Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.