Alfa Romeo 4C Coupe 2016 Owner's Manual PDF

OW N E R S M A N U A L

2 0 1 6

2 0

1 6

4 C

Third Edition Rev 1 Printed in U.S.A.

2016 FCA US LLC. All Rights Reserved. ALFA ROMEO is a registered trademark of FCA Group Marketing S.p.A., used with permission.

164C-126-AC

VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore.

DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, dont drive. Ride with a designated non- drinking driver, call a cab, a friend, or use public trans- portation.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.

This manual illustrates and describes the operation of features and equipment that are either standard or op- tional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle.

FCA US LLC reserves the right to make changes in design and specifications, and/or make additions to or improve- ments to its products without imposing any obligation upon itself to install them on products previously manu- factured.

Copyright 2016 FCA US LLC

TABLE OF CONTENTSSECTION PAGE

1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

5 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235

7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

8 MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319

9 IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331

10 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4

HOW TO USE THIS MANUAL . . . . . . . . . . . . . .5

WARNINGS AND CAUTIONS . . . . . . . . . . . . . .7

VEHICLE IDENTIFICATION NUMBER . . . . . . . .7

VEHICLE MODIFICATIONS/ALTERATIONS . . . .8

1

INTRODUCTION

Congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles.

This Owners Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by Warranty Information, and various customer-oriented documents. Please take the time to read these publications carefully. Following the instruc- tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.

The enclosed Warranty Information lists the services that FCA US LLC offers to its customers:

The Warranty with terms and conditions for maintain- ing its validity

The range of additional services available to FCA US LLC customers

NOTE: After reviewing the owner information, it should be stored in the vehicle for convenient referenc- ing and remain with the vehicle when sold.

When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained tech- nicians and genuine MOPAR parts, and cares about your satisfaction.

4 INTRODUCTION

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section contains the information you desire.

Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicles equipment.

The detailed index at the back of this Owners Manual contains a complete listing of all subjects.

Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owners Manual:

1

INTRODUCTION 5

6 INTRODUCTION

WARNINGS AND CAUTIONS

This Owners Manual contains WARNINGS against operating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warn- ings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears engraved on an Aluminum plate glued and riveted on the floor crossmember under the passenger seat.

NOTE: It is illegal to remove or alter the VIN. Vehicle Identification Number

1

INTRODUCTION 7

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.

8 INTRODUCTION

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .11

Ignition Key Removal . . . . . . . . . . . . . . . . . . .11

Locking Doors With A Key . . . . . . . . . . . . . . .13

Key-In-Ignition Reminder . . . . . . . . . . . . . . . .13

SENTRY KEY . . . . . . . . . . . . . . . . . . . . . . . . . .13

Replacement Keys . . . . . . . . . . . . . . . . . . . . .14

General Information . . . . . . . . . . . . . . . . . . . .14

VEHICLE SECURITY ALARM SYSTEM IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .15

To Arm The System . . . . . . . . . . . . . . . . . . . .15

To Disarm The System . . . . . . . . . . . . . . . . . .16

ILLUMINATED ENTRY . . . . . . . . . . . . . . . . . . .17

REMOTE KEYLESS ENTRY (RKE) IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .17

To Unlock The Doors . . . . . . . . . . . . . . . . . . .18

To Lock The Doors . . . . . . . . . . . . . . . . . . . . .18

Transmitter Battery Replacement . . . . . . . . . . .19

General Information . . . . . . . . . . . . . . . . . . . .21

DOOR LOCKS . . . . . . . . . . . . . . . . . . . . . . . . .21

Central Door Locking/Unlocking . . . . . . . . . . .21

2

Locking/Unlocking Doors From The Inside . . .23

Emergency Door Locking Device . . . . . . . . . . .23

Door Opening/Closing Mechanism Reset . . . . .24

WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Power Windows . . . . . . . . . . . . . . . . . . . . . . .25

DECKLID . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

OCCUPANT RESTRAINT SYSTEMS . . . . . . . . . .29

Important Safety Precautions . . . . . . . . . . . . . .30

Seat Belt Systems . . . . . . . . . . . . . . . . . . . . . .31

Supplemental Restraint System (SRS) . . . . . . . .42

Child Restraints . . . . . . . . . . . . . . . . . . . . . . .55

Transporting Pets . . . . . . . . . . . . . . . . . . . . . .65

ENGINE BREAK-IN RECOMMENDATIONS . . . .66

SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . . .66

Transporting Passengers . . . . . . . . . . . . . . . . .66

Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .67

Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .69

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS

The key fob contains the Remote Keyless Entry (RKE) transmitter with an integrated key. To use the mechanical key simply push the mechanical key release button.

Ignition Key Removal

1. Push the brake pedal and place the transmission into first (1) or reverse (R) gear by selecting/pushing the buttons on the console.

2. Rotate the key to the STOP (OFF/LOCK) position and engage the handbrake and release brake pedal.

Key Fob 1 Vehicle Key 2 Push To Open/Close Vehicle Key

Transmission Gear Selector

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

3. Remove the key from the ignition switch lock cylinder. WARNING!

Before exiting a vehicle, always shift the vehicle into FIRST gear or REVERSE, apply the parking brake, turn the vehicle OFF, remove the key fob from the ignition and lock your vehicle.

Never leave children alone in a vehicle, or with access to an unlocked vehicle.

Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the transmission gear selec- tor.

Do not leave the Key Fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.

(Continued)

Ignition Switch Positions

1 STOP (OFF/LOCK) 2 MAR (ON/RUN) 3 AVV (START)

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING! (Continued) Do not leave children or animals inside parked

vehicles in hot weather. Interior heat build-up may cause serious injury or death.

CAUTION!

An unlocked vehicle is an invitation. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended.

Locking Doors With A Key

You can insert the key with either side up. To lock the door, turn the key to the left. To unlock the door, turn the key to the right. Refer to Body Lubrication in Main- taining Your Vehicle for maintenance information.

Key-In-Ignition Reminder

Opening the drivers door when the key is in the ignition and the ignition switch position is in the STOP (OFF/ LOCK) position, sounds a signal to remove the key.

SENTRY KEY

The Sentry Key Immobilizer System prevents unauthor- ized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.

The system uses ignition keys which have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only keys that are pro- grammed to the vehicle can be used to start and operate the vehicle.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

NOTE: A key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle.

If the Vehicle Security Light is on after the key is turned to the ON/RUN position, it indicates that there is a problem with the electronics.

CAUTION!

Always remove the Sentry Key from the vehicle and lock all doors when leaving the vehicle unat- tended.

The Sentry Key Immobilizer system is not compat- ible with some aftermarket remote starting sys- tems. Use of these systems may result in vehicle starting problems and loss of security protection.

All of the keys provided with your new vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle.

NOTE: When having the Sentry Key Immobilizer Sys- tem serviced, bring all vehicle keys with you to an authorized dealer.

General Information

The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle:

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. This device must accept any interference received, including interference that may cause undesired op- eration.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

VEHICLE SECURITY ALARM SYSTEM IF EQUIPPED

The Vehicle Security Alarm monitors the doors and decklid for unauthorized entry. It will also activate the siren and emit a visual flash of the turn signals (front and rear) for any of the following intrusion cases.

Operation

The alarm activates in the following cases:

1. Wrongful opening of one of the doors or the decklid (perimeter protection);

2. Cutting of the battery leads;

3. Movement inside the passenger compartment (volu- metric protection);

4. Anomalous lifting/tilting of the vehicle.

Operation of the alarm is indicated by a visual signal (flashing of the direction indicators for several seconds). There is a maximum number of visual cycles. When this is reached the system returns to normal operation.

To Arm The System

With the doors and decklid closed and the ignition key either turned to STOP (OFF/LOCK) or removed, point the key towards the vehicle then push and release the lock button.

The system emits a visual signal and activates door locking.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

A self-diagnosis stage lasting approximately 30 seconds precedes the activation of the alarm. During the self- diagnosis, the vehicle security light flashes in the instru- ment panel at a frequency of about one flash per second.

After the self-diagnosis stage, the vehicle security light flashes at a lower frequency (approximately one flash every three seconds).

If, after the alarm is switched on, a second visual signal emit via the vehicle security light in the instrument panel, wait about four seconds and switch off the alarm by pushing the lock button, check that the doors and decklid are closed correctly and then reactivate the system by pushing the unlock button.

If the alarm emits a visual signal even when the doors and decklid are closed correctly, a system malfunction has occurred: in this case, contact a authorized vehicle Dealership.

To Disarm The System

Deactivation

Push the unlock button.

The following operations are performed:

Two brief flashes of the direction indicators.

Unlocking of the doors.

NOTE:

If the central door locking system is released using the metal insert of the key, the alarm is not disabled.

In the event of accidental activation of the alarm, or in any case to interrupt the visual signal cycle when activated, it is possible to push the unlock button or turn the ignition key to MAR (ON/RUN) for at least five seconds, after which the system will deactivate.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Disarming

To completely disable the alarm (e.g. during a lengthy period of vehicle inactivity), lock the vehicle by turning the metal insert of the key in the door lock.

NOTE: If the batteries of the key fob run out or there is a fault in the system, the alarm can be switched off by inserting the key in the ignition switch and turning it to MAR (ON/RUN).

ILLUMINATED ENTRY

The interior lights will turn on whenever a door is opened and the dimmer switch is not in the defeat position.

The interior lights will turn on, remain on for approxi- mately 30 seconds, and then fade to off if a door is opened using the outside door handle and then closed or a door is unlocked using the vehicles key.

The interior lights will turn on and remain on for about four seconds and then fade to off if a door is opened using the inside door handle.

NOTE: The interior light is located in the headliner in between the sun visors. The interior light can be set to three different positions (Off/Left Position, Center Posi- tion, On/Right Position).

REMOTE KEYLESS ENTRY (RKE) IF EQUIPPED

This system allows you to lock or unlock the doors from distances up to approximately 66 ft (20 m) using a hand-held Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

NOTE: The line of transmission must not be blocked with metal objects.

To Unlock The Doors

Push and release the UNLOCK button on the RKE transmitter to unlock the doors. The park lights and turn signal lights will flash to acknowledge the signal and the illuminated entry system will turn on.

NOTE: The Door Unlock Indicator will illuminate in the instrument panel when one or both doors are unlocked.

To Lock The Doors

Push and release the LOCK button on the RKE transmit- ter: locking of doors, switching off of internal roof light and single flashing of direction indicators.

If one or more door are open, the doors will not be locked. This is indicated by a rapid flashing of the direction indicators. The doors will be locked if the decklid is open however.

When a speed of more than 12 mph (20 km/h) is reached, the doors will be locked automatically if the Autoclose

Key Fob

1 Vehicle Key 2 Push To Open/Close Vehicle Key

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

function was selected. Refer to Electronic Vehicle Infor- mation Center (EVIC) in Understanding Your Instru- ment Panel for further information.

When the doors are locked from outside the vehicle (using the remote control), the door lock indicator will illuminate for a few seconds and then start flashing (deterrent function).

Transmitter Battery Replacement

NOTE: Perchlorate Material special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

The recommended replacement battery is CR2032.

Door LED Lock Indicator Battery Replacement Procedure

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

Replace the Key Fob battery with the following proce- dure:

1. Push button #1 and move the metal insert #2 to opening position;

2. Turn screw #3 to unlock using a fine bit screwdriver;

3. Remove battery compartment #4;

4. Replace battery #5, respecting the polarity;

5. Reinsert compartment #4 in the key and secure it by turning screw #3 to lock.

Key Fob Screw Location Key Fob Screw Location

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

General Information

The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle:

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired op- eration.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

DOOR LOCKS

Central Door Locking/Unlocking

Locking Doors From The Outside

With the doors closed, push the lock button on the key fob or turn the metal insert (located inside the key fob) in the door lock.

The Door Lock LED Indicator button will illuminate to indicate that the doors have locked.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

NOTE: Door locking is carried out with all doors shut.

Unlocking Doors From The Outside

Push the unlock button on the key or turn the metal insert (located inside the key) in the driver side door lock.

WARNING!

For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle.

Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.

Do not leave the Key Fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.

Door Lock LED Indicator

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Locking/Unlocking Doors From The Inside

Push the Lock LED Indicator button . The button has an LED that indicates whether the doors are locked or unlocked.

Pushing the Lock LED Indicator button again cen- trally unlocks all doors and switches off the LED.

Pushing the Lock LED Indicator button again cen- trally locks all the doors. The doors will be locked only if all the doors are properly shut.

Once the doors have been locked using the remote control or the key, it will no longer be possible to unlock them by pushing the Lock LED Indicator button .

NOTE: In the absence of electrical power supply (blown fuse, battery disconnected, etc.), it is still possible to lock the doors manually.

Emergency Door Locking Device

Passenger Side Door

The passenger side door has a device to lock it when there is no current.

To lock it, place the metal insert of the ignition key in housing #1 and turn it clockwise.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

To restore the starting condition of the door locks (only if battery charge restored), proceed as follows:

Push the Unlock button on the remote control;

Push the door locking/unlocking LED indicator but- ton on the dashboard; or

Introduce the metal insert of the ignition key in the front door pawl; or

Pull the internal door handle.

Door Opening/Closing Mechanism Reset

If the battery is disconnected or the protection fuse blows, the door opening/closing mechanism must be reset as follows:

1. Close all the doors.

2. Push the unlock button on the key or the door locking/unlocking LED indicator button on the dashboard.

3. Push the lock button on the key or the door locking/ unlocking LED indicator button on the dash- board.

Emergency Door Lock Function

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WINDOWS

Power Windows

NOTE:

These operate when the ignition key is turned to MAR-ON and for about three minutes after the igni- tion key is turned to STOP or removed unless one of the doors is opened.

The buttons are located on the center console.

Push/Pull the corresponding buttons to open/close the desired window.

Power Window Switch

1 Driver Power Window Switch 2 Passenger Power Window Switch

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

When one of the two buttons is pushed briefly, the window moves in stages; if the button is held down to open, continuous automatic operation is activated.

If the button is pushed again, the window will stop in its current position. If the button is pushed for several seconds, the window lowers automatically (only with ignition key in MAR-ON position).

Continuous Automatic Operation

This is activated by pushing one of the two buttons for longer than half a second. The window will stop when it is fully opened, or when the button is pushed again.

It can be used on both the driver side and passenger side, only for lowering the window.

Electric Window System Reset

After a break in power supply for the control units (battery replaced or disconnected or protective fuses for the electric window control units replaced), the auto- matic operation of the windows must be restored.

The restoration procedure must be performed as de- scribed below with the doors closed:

1. Completely open the drivers door window keeping the operating button pushed for at least three seconds after the (lower) end of travel position is reached.

2. Completely raise the driver side window and hold the button down for at least three seconds once the (upper) end of travel position has been reached.

3. Proceed in the same way as described in points 1 and 2 for the passenger side door.

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

4. Make sure that the reset is correct by checking that the windows work automatically.

WARNING!

Improper actuation of the power windows may be dangerous. Never leave children unattended in a vehicle, and do not let children play with power windows. Before and during window operation make sure no one and no object (including clothing) is in the path of the moving glass or its mechanism. Do not leave the key fob in or near the vehicle, or in a location accessible to children. Occupants, particu- larly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.

DECKLID

NOTE: During normal vehicle operation, the luggage compartment can reach temperatures above 149 F (65 C). Pay attention when transporting objects that may be dam- aged at such temperatures. Do not keep aerosol cans in the vehicle: danger of explosion. Aerosol cans must not be exposed to temperatures above 122 F (50 C).

Opening Procedure

With driver side door open, pull lever #1 located at the point illustrated in the figure.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

Raise the decklid and release supporting rod from its locking device.

Insert the end of the rod in housing, making sure that the rod engages in the smallest hole of the retaining clip. Care must be taken to keep the decklid raised until the rod is fixed in the correct position.

NOTE: Maintain a tight grip on the decklid when raising, in order to prevent any external occurrence (e.g. a gust of wind) from suddenly opening the decklid to end of travel. Additionally, in order to prevent any damage to the vehicle or broken windows, do not force the decklid beyond the opening position necessary to secure the supporting rod in the hole of the retaining clip.

Closing Procedure

1. Hold the decklid up with one hand and use the other to remove rod from housing and reinsert it in its locking device.

Decklid Release Lever Location

1 Decklid Release Lever

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Lower the decklid approximately 7.8 inches (20 cm) from the engine compartment and let it drop. Make sure that the decklid is completely closed and not only fastened in safety position by trying to open it. If it is not completely closed, do not push the decklid down, but raise it and repeat the procedure.

NOTE: Always check that the decklid is closed correctly to prevent it from opening while the vehicle is travelling.

WARNING!

The maximum permitted load in the luggage com- partment, in addition to the kits provided, is 33.1 lbs. (15 kg). Do not exceed the maximum permitted load in the luggage compartment.

When accessing the rear luggage compartment, do not come into contact with engine, or other components, that may be hot and could burn you if touched.

(Continued)

WARNING! (Continued) Access the luggage compartment only with the

vehicle stationary. Before exiting a vehicle, always shift the vehicle into FIRST gear or REVERSE, apply the parking brake, turn the vehicle OFF, and remove the key fob from the ignition.

The decklid may drop suddenly, causing serious injury, if the supporting rod is not positioned correctly.

The decklid must always be closed properly, and the lock engaged, while the vehicle is in motion.

OCCUPANT RESTRAINT SYSTEMS

Some of the most important safety features in your vehicle are the restraint systems:

Seat Belt Systems

Supplemental Restraint Systems (SRS) Air Bags

Child Restraints

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29

Important Safety Precautions

Please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible.

Here are some simple steps you can take to minimize the risk of harm from a deploying air bag:

1. Children 12 years old and under should always ride buckled up in a vehicle with a rear seat.

2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (Refer to Child Restraints)

3. Children that are not big enough to wear the vehicle seat belt properly (Refer to Child Restraints) should be secured in a vehicle with a rear seat in child

restraints or belt-positioning booster seats. Older chil- dren who do not use child restraints or belt- positioning booster seats should ride properly buckled up in a vehicle with a rear seat.

4. Never allow children to slide the shoulder belt behind them or under their arm.

5. You should read the instructions provided with your child restraint to make sure that you are using it properly.

6. All occupants should always wear their lap and shoulder belts properly.

7. The driver and front passenger seats should be moved back as far as practical to allow the Advanced Front Air Bags room to inflate.

8. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the

30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

side air bags will inflate forcefully into the space between occupants and the door and occupants could be injured.

9. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under If You Need Assistance.

WARNING!

Never place a rear-facing child restraint in front of an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint.

Only use a rear-facing child restraint in a vehicle with a rear seat.

Seat Belt Systems

Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and could cause a collision that includes you. This can happen far away from home or on your own street.

Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times.

Driver And Passenger BeltAlert (If Equipped)

BeltAlert is a feature intended to remind the driver and outboard front seat passenger (if equipped with outboard front passenger seat BeltAlert) to buckle

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31

their seat belts. The Belt Alert feature is active when- ever the ignition switch is in the AVV/START or MAR/RUN position.

Initial Indication

If the driver is unbuckled when the ignition switch is first turned to the AVV/START or MAR/RUN position, a chime will signal for a few seconds. If the driver or outboard front seat passenger (if equipped with outboard front passenger seat BeltAlert) is unbuckled when the ignition switch is first turned to the AVV/START or MAR/ RUN position the Seat Belt Reminder Light will turn on and remain on until both outboard front seat belts are buckled. The outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is unoccupied.

BeltAlert Warning Sequence

The BeltAlert warning sequence is activated when the vehicle is moving above a specified vehicle speed range and the driver or outboard front seat passenger is un- buckled (the outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is unoccupied). The BeltAlert warning sequence starts by blinking the Seat Belt Reminder Light and sounding an intermittent chime. Once the BeltAlert warning sequence has completed, the Seat Belt Reminder Light will remain on until the seat belts are buckled. The BeltAlert warning sequence may repeat based on vehicle speed until the driver and occupied outboard front seat passenger seat belts are buckled. The driver should instruct all occu- pants to buckle their seat belts.

32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Change Of Status

If the driver or outboard front seat passenger (if equipped with outboard front passenger seat BeltAlert) unbuckles their seat belt while the vehicle is traveling, the BeltAlert warning sequence will begin until the seat belts are buckled again. The outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is unoccupied. BeltAlert may be triggered when an animal or heavy object is on the outboard front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed.

BeltAlert can be activated or deactivated by your autho- rized dealer. FCA US LLC does not recommend deacti- vating BeltAlert.

NOTE: If BeltAlert has been deactivated and the driver or outboard front seat passenger is unbuckled the Seat Belt Reminder Light will turn on and remain on until the driver and outboard front seat passenger seat belts are buckled.

Lap/Shoulder Belts

All seating positions in your vehicle are equipped with lap/shoulder belts.

The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoul- der part of the seat belt to move freely with you under normal conditions. However, in a collision the seat belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out of the vehicle.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33

WARNING!

Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags wont deploy at all. Always wear your seat belt even though you have air bags.

In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.

It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.

(Continued)

WARNING! (Continued) Do not allow people to ride in any area of your

vehicle that is not equipped with seats and seat belts.

Be sure everyone in your vehicle is in a seat and using a seat belt properly.

Wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too.

Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.

(Continued)

34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING! (Continued) A lap belt worn too high can increase the risk of

injury in a collision. The seat belt forces wont be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug.

A twisted seat belt may not protect you properly. In a collision, it could even cut into you. Be sure the seat belt is flat against your body, without twists. If you cant straighten a seat belt in your vehicle, take it to your authorized dealer immediately and have it fixed.

A seat belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing inter- nal injuries. Always buckle your seat belt into the buckle nearest you.

(Continued)

WARNING! (Continued) A seat belt that is too loose will not protect you

properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.

A seat belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A seat belt worn under the arm can cause internal injuries. Ribs arent as strong as shoulder bones. Wear the seat belt over your shoulder so that your strongest bones will take the force in a collision.

A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.

(Continued)

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35

WARNING! (Continued) A frayed or torn seat belt could rip apart in a

collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be re- placed immediately. Do not disassemble or modify the seat belt system. Seat belt assemblies must be replaced after a collision.

Lap/Shoulder Belt Operating Instructions

1. Enter the vehicle and close the door. Sit back and adjust the seat.

2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the seat belt. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around your lap.

3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a click.

Pulling Out The Latch Plate

36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding under the seat belt in a collision.

5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt.

6. To release the belt, push the red button on the buckle. The seat belt will automatically retract to its stowed

Inserting Latch Plate Into Buckle Positioning The Lap Belt

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37

position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully.

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/ shoulder belt.

1. Position the latch plate as close as possible to the anchor point.

2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.

3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.

4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.

Seat Belts And Pregnant Women

Seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt.

Pregnant Women And Seat Belts

38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Position the lap belt snug and low below the abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away from the neck. Never place the shoulder belt behind the back or under the arm.

Seat Belt Pretensioner

The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision. Pretensioners work for all size occupants, including those in child restraints.

NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly.

The pretensioners are triggered by the Occupant Re- straint Controller (ORC). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately.

Energy Management Feature

This vehicle has a seat belt system with an Energy Management feature in the front seating positions that may help further reduce the risk of injury in the event of a collision. This seat belt system has a retractor assembly that is designed to release webbing in a controlled manner.

Switchable Automatic Locking Retractor (ALR)

The seat belt in the passenger seating position is equipped with a Switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to Installing Child Restraints Using The Vehicle Seat Belt under the Child

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39

Restraints section of this manual. The table below defines the type of feature for each seating position.

If the passenger seating position is equipped with an ALR and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupants mid-section so as to not activate the ALR. If the ALR is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupants mid-section. Slide the latch plate into the buckle until you hear a click.

In Automatic Locking Mode, the shoulder belt is auto- matically pre-locked. The seat belt will still retract to remove any slack in the shoulder belt. Use the Automatic Locking Mode anytime a child restraint is installed in a seating position that has a seat belt with this feature. Children 12 years old and under should always be properly restrained in a vehicle with a rear seat. ALR = Switchable Automatic Locking Retractor

40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint.

Only use a rear-facing child restraint in a vehicle with a rear seat.

How To Engage The Automatic Locking Mode

1. Buckle the combination lap and shoulder belt.

2. Grasp the shoulder portion and pull downward until the entire seat belt is extracted.

3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat belt is now in the Automatic Locking Mode.

How To Disengage The Automatic Locking Mode

Unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking mode.

WARNING!

The seat belt assembly must be replaced if the switchable Automatic Locking Retractor (ALR) fea- ture or any other seat belt function is not working properly when checked according to the proce- dures in the Service Manual.

Failure to replace the seat belt assembly could increase the risk of injury in collisions.

Do not use the Automatic Locking Mode to restrain occupants who are wearing the seat belt or children who are using booster seats. The locked mode is

(Continued)

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41

WARNING! (Continued) only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child.

Supplemental Restraint System (SRS)

Air Bag System Components

Your vehicle may be equipped with the following air bag system components:

Occupant Restraint Controller (ORC)

Air Bag Warning Light

Steering Wheel and Column

Instrument Panel

Knee Impact Bolsters

Advanced Front Air Bags

Supplemental Side Air Bags

Supplemental Knee Air Bags

Front and Side Impact Sensors

Seat Belt Pretensioners

Seat Belt Buckle Switch

Seat Track Position Sensors

Advanced Front Air Bags

This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The drivers Advanced Front Air Bag is mounted in the center of the steering wheel. The passengers Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG or AIRBAG are embossed on the air bag covers.

42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.

Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint.

Only use a rear-facing child restraint in a vehicle with a rear seat.

Advanced Front Air Bag Locations

1 Driver And Passenger Advanced Front Air Bags 2 Passenger Knee Bolsters 3 Supplemental Driver Knee Air Bag/Driver Knee Bolster

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43

Advanced Front Air Bag Features

The Advanced Front Air Bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors or other system components.

The first stage inflator is triggered immediately during an impact that requires air bag deployment. A low energy output is used in less severe collisions. A higher energy output is used for more severe collisions.

This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether the driver or front passenger seat belt is buckled. The seat belt buckle switch may adjust the inflation rate of the Advanced Front Air Bags.

WARNING!

No objects should be placed over or near the air bag on the instrument panel or steering wheel because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate.

Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating.

Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In

(Continued)

44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING! (Continued) some collisions, air bags wont deploy at all. Al- ways wear your seat belts even though you have air bags.

Advanced Front Air Bag Operation

Advanced Front Air Bags are designed to provide addi- tional protection by supplementing the seat belts. Ad- vanced Front Air Bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. The Ad- vanced Front Air Bags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage for example, some pole collisions, truck underrides, and angle offset collisions.

On the other hand, depending on the type and location of impact, Advanced Front Air Bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration.

Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed.

Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away from an inflating air bag.

When the ORC detects a collision requiring the Ad- vanced Front Air Bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the Advanced Front Air Bags.

The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The Advanced Front Air Bags fully inflate in less time than it takes to blink your eyes. The air bags then quickly deflate while helping to restrain the driver and front passenger.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45

Knee Impact Bolsters

The Knee Impact Bolsters help protect the knees of the driver and front passenger, and position the front occu- pants for improved interaction with the Advanced Front Air Bags.

WARNING!

Do not drill, cut, or tamper with the knee impact bolsters in any way.

Do not mount any accessories to the knee impact bolsters such as alarm lights, stereos, citizen band radios, etc.

Supplemental Driver Knee Air Bag

This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column. The Supplemental Driver Knee Air Bag

provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and Advanced Front Air Bags.

Supplemental Door-Integrated Side Air Bags

This vehicle is equipped with Supplemental Door- Integrated Side Air Bag Inflatable Curtains (SABICs).

SABICs may help reduce the risk of head and other injuries to front outboard occupants in certain side im- pacts, in addition to the injury reduction potential pro- vided by the seat belts and body structure.

The SABICs are located in the door trim below the side windows. The trim covering the SABICs is labeled SRS AIRBAG or AIRBAG.

46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

The SABICs may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events.

The SABICs deploy upward, covering the side windows. An inflating SABIC pushes the outside edge of the trim out of the way and covers the window. The SABICs

inflate with enough force to injure occupants if they are not belted and seated properly, or if items are positioned in the area where the SABICs inflate. Children are at an even greater risk of injury from a deploying air bag.

SABICs are designed to activate in certain side impacts. The Occupant Restraint Controller (ORC) determines whether the deployment of the SABIC in a particular impact event is appropriate, based on the severity and type of collision. The side impact sensors aid the ORC in determining the appropriate response to impact events. The system is calibrated to deploy the SABIC on the impact side of the vehicle during impacts that require SABIC occupant protection. In side impacts, the SABICs deploy independently; a left side impact deploys the left side SABIC only and a right-side impact deploys the right side SABIC only. Vehicle damage by itself is not a good indicator of whether or not SABICs should have deployed.

Supplemental Door-Integrated Side Air Bag Label

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47

SABICs will not deploy in all side collisions, including some collisions at certain angles, or some side collisions that do not impact the area of the passenger compart- ment. SABICs may deploy during angled or offset frontal collisions where the Advanced Front Air Bags deploy.

SABICs are a supplement to the seat belt restraint system. SABICs deploy in less time than it takes to blink your eyes. Occupants, including children, who are up against or very close to SABICs can be seriously injured or killed. Occupants, including children, should never lean on or sleep against the door, side windows, or area where the side air bags inflate, even if they are in an infant or child restraint.

Seat belts (and child restraints where appropriate) are necessary for your protection in all collisions. They also help keep you in position, away from an inflating SABIC. To get the best protection from the SABICs, occupants must wear their seat belts properly and sit upright with

their backs against the seats. Children must be properly restrained in a child restraint or booster seat that is appropriate for the size of the child.

WARNING!

Your vehicle is equipped with left and right Supple- mental Door-Integrated Side Air Bag Inflatable Cur- tains (SABICs). Do not stack luggage or other cargo up high enough to block the deployment of the SABICs. The door trim below the side windows where the SABIC and its deployment path are lo- cated, should remain free from any obstructions.

SABICs need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.

Being too close to the SABICs during deployment could cause you to be severely injured or killed.

(Continued)

48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING! (Continued) Relying on the SABICs alone could lead to more

severe injuries in a collision. The SABICs work with your seat belt to restrain you properly. In some collisions, SABICs wont deploy at all. Al- ways wear your seat belt even though you have SABICs.

NOTE: Air bag covers may not be obvious to you, but they will open during air bag deployment.

If A Deployment Occurs

The Advanced Front Air Bags are designed to deflate immediately after deployment.

NOTE: Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system.

If you do have a collision which deploys the air bags, any or all of the following may occur:

The air bag material may sometimes cause abrasions and/or skin reddening to the occupants as the air bags deploy and unfold. The abrasions are similar to fric- tion rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you havent healed significantly within a few days, or if you have any blistering, see your doctor immediately.

As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49

continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturers in- structions for cleaning.

Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you.

WARNING!

Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by an authorized dealer imme- diately. Also, have the Occupant Restraint Controller System serviced as well.

NOTE:

Air bag covers may not be obvious in the interior trim, but they will open during air bag deployment.

After any collision, the vehicle should be taken to an authorized dealer immediately.

Enhanced Accident Response System

In the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the ORC will determine whether to have the Enhanced Accident Response Sys- tem perform the following functions:

Cut off fuel to the engine.

Flash hazard lights as long as the battery has power or until the hazard light button is pushed. The hazard lights can be deactivated by pushing the hazard light button.

Turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the Enhanced Accident Response Sys- tem.

50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Unlock the power door locks.

Enhanced Accident Response System Reset Procedure

After the event occurs, when the system is active, a message regarding fuel cutoff is displayed. Turn the ignition switch from ignition AVV/START or MAR/ ACC/ON/RUN to ignition STOP/OFF/LOCK. Care- fully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine com- partment and fuel tank before resetting the system and starting the engine.

Depending on the nature of the event the left and right turn signal lights, located in the instrument panel, may both be blinking and will continue to blink. In order to move your vehicle to the side of the road, you must follow the system reset procedure.

Customer Action Customer Will See 1. Turn Ignition OFF.

(Turn Signal Switch Must Be Placed In Neutral

State). 2. Turn Ignition ON. Left Turn Light Is OFF.

Right Turn Light BLINKS.

3. Turn Right Turn Signal Switch ON.

Right Turn Light Is ON SOLID. Left Turn Light

BLINKS. 4. Turn Left Turn Signal

Switch ON. Left Turn Light Is ON

SOLID. Right Turn Signal Light BLINKS.

5. Turn Right Turn Signal Switch ON.

Right Turn Light Is ON SOLID. Left Turn Light

BLINKS.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51

Customer Action Customer Will See 6. Turn Left Turn Signal

Switch ON. Left Turn Light Is ON

SOLID. Right Turn Light Is ON SOLID.

7. Turn Left Turn Signal Switch OFF. (Turn Signal Switch Must Be Placed In

Neutral State).

Left Turn light Is OFF. Right Turn Light is OFF.

8. Turn Ignition OFF. 9. Turn Hazard Flashers

OFF (Manually). System is now reset and

the engine may be started.

If a reset procedure step is not completed within 60 seconds, then the turn signal lights will blink and the reset procedure must be performed again in order to be successful.

Air Bag Warning Light

The air bags must be ready to inflate for your protection in a collision. The Occupant Re- straint Controller (ORC) monitors the internal circuits and interconnecting wiring associated

with air bag system electrical components.

The ORC monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the AVV/START or MAR/ACC/ON/RUN position. If the ignition switch is in the STOP/OFF/LOCK position the air bag system is not on and the air bags will not inflate.

The ORC contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment.

The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition switch is first turned to

52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

the MAR/ACC/ON/RUN position. After the self-check, the Air Bag Warning Light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the Air Bag Warning Light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after initial startup.

The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunc- tion is detected that could affect the air bag system. The diagnostics also record the nature of the malfunction. While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.

The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first turned to the MAR/ACC/ON/RUN position.

The Air Bag Warning Light remains on after the four to eight-second interval.

The Air Bag Warning Light comes on intermittently or remains on while driving.

NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. In this condition the air bags may not be ready to inflate for your protec- tion. Have an authorized dealer service the air bag system immediately.

WARNING!

Ignoring the Air Bag Warning Light in your instru- ment panel could mean you wont have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53

Maintaining Your Air Bag System

WARNING!

Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards.

It is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system.

Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may

(Continued)

WARNING! (Continued) not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer. Only manufacturer approved seat accessories may be used. If it is necessary to modify the air bag system for persons with dis- abilities, contact your authorized dealer.

Event Data Recorder (EDR)

This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will

54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

assist in understanding how a vehicles systems per- formed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record such data as:

How various systems in your vehicle were operating;

Whether or not the driver and passenger safety belts were buckled/fastened;

How far (if at all) the driver was depressing the accelerator and/or brake pedal; and,

How fast the vehicle was traveling.

These data can help provide a better understanding of the circumstances in which crashes and injuries occur.

NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no per- sonal data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law en- forcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.

To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the EDR.

Child Restraints

Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the United States, and every Canadian province, requires

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55

that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.

Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.

WARNING!

In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the childs size.

There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child

seat Owners Manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in the child restraint Owners Manual and on all the labels attached to the child restraint.

Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it.

NOTE:

For additional information, refer to www.seatcheck.org or call 18667328243.

Canadian residents should refer to Transport Canadas website for additional information: http://www.tc.gc.ca/ eng/motorvehiclesafety/safedrivers-childsafety-index- 53.htm

56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Summary Of Recommendations For Restraining Children In Vehicles

Child Size, Height, Weight or Age Recommended Type of Child Restraint Infants and Toddlers Children who are two years old or

younger and who have not reached the height or weight limits of their child

restraint

Either an Infant Carrier or a Convertible Child Restraint, facing rearward in the

rear seat of the vehicle

Small Children Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child

restraint

Forward-Facing Child Restraint with a five-point Harness, facing forward in the

rear seat of the vehicle

Larger Children Children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicles

seat belt

Belt Positioning Booster Seat and the vehicle seat belt, seated in the rear seat

of the vehicle

Children Too Large for Child Restraints

Children 12 years old or younger, who have out-grown the height or weight

limit of their booster seat

Vehicle Seat Belt, seated in the rear seat of the vehicle

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57

Infant and Child Restraints

Safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and convertible child seats.

The infant carrier is only used rear-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. Convertible child seats can be used either rear-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rear-facing direction than infant carriers do, so they can be used rear-facing by children who have outgrown their infant carrier but are still less than at least two years old. Children should remain rear-facing until they reach the highest weight or height allowed by their convertible child seat.

WARNING!

Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint.

Only use a rear-facing child restraint in a vehicle with a rear seat.

Older Children And Child Restraints

Children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direc- tion are for children who are over two years old or who have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should

58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat.

All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicles seat belts fit properly. If the child cannot sit with knees bent over the vehicles seat cushion while the childs back is against the seatback, they should use a belt-positioning booster seat. The child and belt-positioning booster seat are held in the vehicle by the seat belt.

WARNING!

Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturers

(Continued)

WARNING! (Continued) directions exactly when installing an infant or child restraint.

After a child restraint is installed in the vehicle, do not move the vehicle seat forward or rearward because it can loosen the child restraint attach- ments. Remove the child restraint before adjusting the vehicle seat position. When the vehicle seat has been adjusted, reinstall the child restraint.

When your child restraint is not in use, secure it in the vehicle with the seat belt or LATCH anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal injury.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59

Children Too Large For Booster Seats

Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether the child can use the vehicles seat belt alone:

1. Can the child sit all the way back against the back of the vehicle seat?

2. Do the childs knees bend comfortably over the front of the vehicle seat while they are still sitting all the way back?

3. Does the shoulder belt cross the childs shoulder between their neck and arm?

4. Is the lap part of the belt as low as possible, touching the childs thighs and not their stomach?

5. Can the child stay seated like this for the whole trip?

If the answer to any of these questions was no, then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched. A childs squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly.

WARNING!

Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly.

60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Installing Child Restraints Using The Vehicle Seat Belt

The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The ALR retractor can be switched into a locked mode by pulling all of the webbing out of the retractor and then letting the webbing retract back into the retractor. If it is locked, the ALR will make a clicking noise while the webbing is pulled back into the retractor. Refer to Occupant Restraints in Things To Know Before Starting Your Vehicle for additional information on ALR.

Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle

ALR = Switchable Automatic Locking Retractor

Top Tether Anchorage Symbol

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61

What is the weight limit (childs weight + weight of the child re-

straint) for using the Tether Anchor with the seat belt to attach a for-

ward facing child restraint?

Weight limit of the Child Restraint Always use the tether anchor when using the seat belt to install a for- ward facing child restraint, up to the recommended weight limit of

the child restraint. Can the head restraints be re-

moved? No

Can the buckle stalk be twisted to tighten the seat belt against the belt

path of the child restraint?

No Do not twist the buckle stalk in a seating position with an ALR re-

tractor.

Installing A Child Restraint With A Switchable Automatic Locking Retractor (ALR):

1. Place the child seat in the center of the seating position. Move the vehicle seat as far rearward as possible to keep the child as far from the advanced passenger air bag as possible.

2. Pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path.

3. Slide the latch plate into the buckle until you hear a click.

4. Pull on the webbing to make the lap portion tight against the child seat.

62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode.

6. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any web- bing. If the retractor is not locked, repeat step 5.

7. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat.

8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether

strap. See the section Installing Child Restraints Using the Top Tether Anchorage for directions to attach a tether anchor.

9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction.

Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.

Installing Child Restraints Using The Top Tether Anchorage:

WARNING!

Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the

(Continued)

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63

WARNING! (Continued) tether strap of a rear-facing car seat to the tether anchorage that is approved for that seating position, located behind the top of the vehicle seat. See the section Lower Anchors and Tethers for CHildren (LATCH) Restraint System for the location of ap- proved tether anchorages in your vehicle.

Always use the tether anchor when using the seat belt to install a forward facing child restraint, up to the recom- mended weight limit of the child restraint. This vehicle is equipped with a tether anchorage, located behind the front passenger seat, near the floor.

Upper Tether Anchorage

64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available.

2. Route the tether strap around the outboard side of the head restraint to the tether anchorage.

3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram.

4. Remove slack in the tether strap according to the child restraint manufacturers instructions.

WARNING!

An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly be- hind the child seat to secure a child restraint top tether strap.

Transporting Pets

Deploying air bags could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in an collision.

Pets should be restrained in pet harnesses or pet carriers that are secured by seat belts.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65

ENGINE BREAK-IN RECOMMENDATIONS

A long break-in period is not required for the drivetrain (engine, transmission, and rear axle) in your new vehicle.

Driving your vehicle with a new transmission requires no special techniques but, to reach optimal shifting quality and help with engine Break-in, Dynamic and Race Mode will be inhibited until the vehicle has accumulated 155 miles (250 km).

Additionally, for the first 200 miles (300 km), following these few simple guidelines is all that is necessary for a good break-in.

Avoid very aggressive driving.

Avoid driving at a constant speed, either fast or slow, for long periods.

Do not make any full throttle starts and avoid full throttle acceleration while cruising within the posted speed limits of local traffic laws.

Use the proper gear for your speed range.

Wait until the engine has reached normal operating temperature before driving at the recommended maxi- mum break-in speed.

Avoid excessive idling.

Check the engine oil level at every fuel fill.

SAFETY TIPS

Transporting Passengers

NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.

66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.

Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

Be sure everyone in your vehicle is in a seat and using a seat belt properly.

Exhaust Gas

WARNING!

Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: Do not run the engine in a closed garage or in

confined areas any longer than needed to move your vehicle in or out of the area.

If you are required to drive with the trunk/liftgate/ rear doors open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode.

(Continued)

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67

WARNING! (Continued) If it is necessary to sit in a parked vehicle with the

engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.

The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.

Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.

Safety Checks You Should Make Inside The Vehicle

Seat Belts

Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.

Front seat belt assemblies must be replaced after a collision. Seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt.

Air Bag Warning Light

The light should come on and remain on for four to eight seconds as a bulb check when the ignition is first cycled to ON. If the light is not lit during starting, see your autho- rized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer.

68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Defroster

Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your autho- rized dealer for service if your defroster is inoperable.

Floor Mat Safety Information

Always use floor mats designed to fit the foot well of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways.

Periodic Safety Checks You Should Make Outside The Vehicle

Tires

Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects

lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires for proper pressure.

Lights

Have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.

Door Latches

Check for positive closing, latching, and locking.

Fluid Leaks

Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid (if equipped), or brake fluid leaks are suspected, the cause should be located and corrected immediately.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CONTENTS MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Inside Day/Night Mirror . . . . . . . . . . . . . . . .74

Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .75

Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . .75

Folding Mirrors. . . . . . . . . . . . . . . . . . . . . . . .76

Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . .77

SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Manual Seats . . . . . . . . . . . . . . . . . . . . . . . . .77

Non-Adjustable Head Restraints . . . . . . . . . . .80

TO OPEN AND CLOSE THE DECKLID . . . . . . .80

LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Multifunction Lever. . . . . . . . . . . . . . . . . . . . .83

Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Daytime Running Lights . . . . . . . . . . . . . . . . .85

High Beams . . . . . . . . . . . . . . . . . . . . . . . . . .85

Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . .85

Parking Lights . . . . . . . . . . . . . . . . . . . . . . . .85

Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . .85

Lane Change Assist . . . . . . . . . . . . . . . . . . . .86

3

Follow Me Home/Headlight Delay If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Dimmer Controls . . . . . . . . . . . . . . . . . . . . . .86

Interior Light . . . . . . . . . . . . . . . . . . . . . . . . .87

WINDSHIELD WIPERS AND WASHERS . . . . . .89

Intermittent Wiper System . . . . . . . . . . . . . . .89

Windshield Wiper Operation . . . . . . . . . . . . . .89

Mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Windshield Washers . . . . . . . . . . . . . . . . . . . .90

TILT/TELESCOPING STEERING COLUMN . . . .90

ELECTRONIC SPEED CONTROL IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . .91

To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . .92

To Set A Desired Speed . . . . . . . . . . . . . . . . . .93

To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . .93

To Resume Speed . . . . . . . . . . . . . . . . . . . . . .93

To Vary The Speed Setting . . . . . . . . . . . . . . . .93

To Accelerate For Passing . . . . . . . . . . . . . . . .95

PARKING SENSORS IF EQUIPPED . . . . . . . .95

Activation/Deactivation. . . . . . . . . . . . . . . . . .96

Acoustic Signal . . . . . . . . . . . . . . . . . . . . . . . .96

Indications On Display If Equipped . . . . . . .97

Fault Indication. . . . . . . . . . . . . . . . . . . . . . . .98

General Warnings . . . . . . . . . . . . . . . . . . . . . .98

POWER OUTLETS . . . . . . . . . . . . . . . . . . . . .100

CIGAR LIGHTER AND ASH RECEIVER IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .102

72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CUPHOLDER . . . . . . . . . . . . . . . . . . . . . . . . .103

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Seatback Storage . . . . . . . . . . . . . . . . . . . . . .103

Console Features . . . . . . . . . . . . . . . . . . . . . .104

Rear Compartment Storage. . . . . . . . . . . . . . .104

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73

MIRRORS

Inside Day/Night Mirror

A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.

Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while the small control under the mirror is set in the day position (toward the windshield).

Adjusting Rearview Mirror

74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Outside Mirrors

To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror.

NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.

WARNING!

Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror.

Power Mirrors

The power mirror controls are located on the center console.

Power Mirror Control

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75

The power mirror controls consist of mirror select knob and a four-way mirror control switch. To adjust a mirror, turn the power mirror control knob to the left or right to select the mirror that you want to adjust.

Using the mirror control switch, push on any of the four arrows for the direction that you want the mirror to move.

Folding Mirrors

The exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forward, full rear- ward and normal. Folding Mirrors

76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Heated Mirrors

These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the mirror defroster.

SEATS

Seats are a part of the Occupant Restraint System of the vehicle.

WARNING!

It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.

(Continued)

WARNING! (Continued) Do not allow people to ride in any area of your

vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed.

Be sure everyone in your vehicle is in a seat and using a seat belt properly.

Manual Seats

Forward And Rearward Adjustment

The adjusting bar is at the front of the driver seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the desired

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77

position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.

Seat Height Adjustment

In order to achieve the ideal driving position, the height of the seats can also be adjusted. Tools are required to make this height adjustment. Contact your authorized dealership.

Recliner Adjustment

The recliner lever is located on the outboard side of the seat. To recline the seat, lean forward slightly, pull the recliner lever upward, lean backward until the seat is in the desired position, and release the lever. To return the seat to its full upright position, lean forward, pull the recliner lever upward and hold it until the seat returns to its full upright position.

Seat Adjustment Bar

78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.

Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.

Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.

Recline Lever

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79

Non-Adjustable Head Restraints

The non-adjustable head restraints are form fitted into the upper structure of the seatback and are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. The seatback should be properly adjusted to an upright position where the head restraint is positioned as close as possible to the back of your head.

WARNING!

Be certain that the seatback is locked securely into position. Otherwise, the seat will not provide the proper stability for passengers. An improperly latched seatback could cause serious injury.

TO OPEN AND CLOSE THE DECKLID

CAUTION!

To prevent possible damage, do not slam the deck- lid to close it. Use a firm downward push at the center of the decklid to ensure the decklid latch is fully engaged.

During normal vehicle operation, the luggage com- partment (located rear of the engine) can reach temperatures above 149 degrees. Do not transport objects in the luggage compartment that may be damaged at such temperatures. Do not place aero- sol cans in the luggage compartment.

80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To open the decklid:

1. Open the drivers side door.

2. Pull the decklid release lever located on the rear of the drivers door sill.

3. Move to the rear of the vehicle and lift the decklid.

Decklid Release Lever

Decklid Lift Point Location

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81

4. Lift upward on the decklid prop rod to release it from the stowage retainer.

5. Place the decklid prop rod in the decklid slot to secure the decklid in the open position.

Decklid Prop Rod Location

1 Decklid Prop Rod 2 Stowage Retainer Location

Decklid Prop Rod Slot

82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

The maximum load limit for the luggage compart- ment, in addition to the kits provided, is 33.1 lbs. (15kg). Do not exceed the maximum permitted load in the luggage compartment. When accessing the rear luggage compartment, do not come into con- tact with engine, or other components, that may be hot and could burn you if touched.

Access the luggage compartment only with the vehicle stationary. Before exiting the vehicle, you should always place the vehicle into FIRST gear or REVERSE, apply the parking brake, and remove the key from the ignition. Never leave the key fob in the vehicle or in a location accessible to children.

The decklid may drop suddenly, causing serious injury, if the supporting rod is not positioned correctly.

(Continued)

WARNING! (Continued) The decklid must always be closed properly, and

the lock engaged, while the vehicle is in motions.

LIGHTS

Multifunction Lever

The multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight beam selection, passing light and turn signals.

NOTE: The external lights can only be turned on with the ignition in the ON/RUN position.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83

Headlights

Rotate the end of the multifunction lever up- ward to the first detent for headlight operation.

NOTE: When the headlights are turned on, the Daytime Running Lights will be deactivated.

Multifunction Lever Headlight Operation

84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Daytime Running Lights

To activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O symbol.

NOTE: The low beams and side/tail lights will not be on with DRL.

High Beams

With the low beams activated, pull the multifunc- tion lever towards the steering wheel to turn on

the high beams. A high beam symbol will illuminate in the cluster to indicate the high beams are on. Pull the multifunction lever a second time to switch the head- lights back to low beam.

Flash-To-Pass

You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released.

Parking Lights

To turn on the parking lights, remove the key or turn the ignition to OFF/LOCK position and turn on the headlights.

Turn Signals

Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85

NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective.

Lane Change Assist

Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash five times then automatically turn off.

Follow Me Home/Headlight Delay If Equipped

When this feature is selected the driver can choose to have the headlights remain on for a preset period of time.

Activation

Remove the key or turn the ignition to the OFF/LOCK position, and pull the multifunction lever toward the steering wheel, within two minutes. Each time the lever is pulled, the activation of the lights will be extended by 30 seconds. The activation of the lights can be extended to a maximum of 210 seconds.

Deactivation

Pull the multifunction lever toward the steering wheel and hold it for more than two seconds.

Dimmer Controls

The dimmer controls are located on the left side of the instrument panel below the instrument cluster.

86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Pushing the up or down arrow will increase or decrease the brightness of the instrument panel lights.

Interior Light

The interior light is located in the headliner in between the sun visors. The interior light can be set to three different positions (Off/Left Position, Center Position, On/Right Position).

Using the interior light lens, push the lens to the right from its center position and the lights are always on. Push the lens to the left from its center position and the lights are always off. Leave the lens in the center position, and the light is turned on and off when the doors are opened or closed.

Dimmer Controls

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

CAUTION!

Before getting out of the vehicle be sure that the Overhead Dome Lamp is in the center position or that the lights are off to avoid draining the battery.

Interior Light Timing (Center Position)

There are four different modes of operation that can be activated in this position:

When one door is opened a three minute timer is activated.

When the key is removed from the ignition (within two minutes of the ignition being turned off), a 10 second timer is activated.

When the doors are unlocked with the Key Fob a 10 second timer is activated.

When the doors are locked with the Key Fob the lights will turn off.

Interior Light (Off Position Shown)

88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WINDSHIELD WIPERS AND WASHERS

The windshield wiper/washer controls are located on the windshield wiper/washer lever on the right side of the steering column. The front wipers are operated by rotat- ing a switch, located on the end of the lever.

Intermittent Wiper System

Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles. Rotate the end of the multifunction lever to the first detent position. There are four possible delay intervals that depend on the vehicle speed.

Windshield Wiper Operation

Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper opera- tion.

Mist

Use the mist feature when weather conditions make occasional usage of the wipers necessary. Push the lever upward to the mist position and release for a single wiping cycle.

Windshield Wiper/Washer Lever

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89

NOTE: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid.

Windshield Washers

To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will start and continue to operate for three wipe cycles after the lever is released, and then resume the intermittent interval previously selected.

If the lever is pulled while in the off position, the wipers will operate for three wipe cycles and then turn off.

WARNING!

Sudden loss of visibility through the windshield could lead to a collision. You might not see other

(Continued)

WARNING! (Continued) vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.

TILT/TELESCOPING STEERING COLUMN

This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column.

90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the lever upward until fully engaged.

WARNING!

Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.

ELECTRONIC SPEED CONTROL IF EQUIPPED

When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 18 mph (30 km/h) up to the maximum speed of 105 mph (170 km/h).

The Electronic Speed Control Lever is located on the left side of the steering column.

Tilt/Telescoping Column Lever

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91

NOTE: In order to ensure proper operation, the Electronic Speed Control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the Electronic Speed Control system can be reactivated rotating the end of the multifunction lever (On/Off) and resetting the desired vehicle set speed.

To Activate

Rotate the end of the multifunction lever to activate the Electronic Speed Control. The Cruise Indicator Light in the Electronic Vehicle Information Center (EVIC) will illuminate. To turn the system off, rotate the end of the multifunction lever to the O position. The Cruise Indicator Light will turn off. The system should be turned off when not in use.

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.

Electronic Speed Control Lever

92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To Set A Desired Speed

Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, move the electronic speed control lever upward SET(+) and release. Release the accelerator and the vehicle will operate at the selected speed.

NOTE: The vehicle should be traveling at a steady speed and on level ground before moving the electronic speed control lever upward SET(+).

To Deactivate

A soft tap on the brake pedal, pushing the RESUME/ CANCEL button, or normal brake pressure while slow- ing the vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Rotating the end of the multifunction lever to the O position or turning the ignition switch OFF erases the set speed memory.

To Resume Speed

To resume a previously set speed, push the RESUME button and release. Resume can be used at any speed above 18 mph (30 km/h).

To Vary The Speed Setting

To Increase Speed

When the Electronic Speed Control is set, you can in- crease speed by tapping the Speed Control lever up (+).

The speed increment shown is dependant on the speed of U.S. (mph) or Metric (km/h) units:

U.S. Speed (mph)

Tapping the Speed Control lever up (+) once will result in a 1 mph increase in set speed. Each subsequent tap of the lever results in an increase of 1 mph.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93

If the lever is continually help up, the set speed will continue to increase until the lever is released, then the new set speed will be established.

Metric Speed (km/h)

Tapping the Speed Control lever up (+) once will result in a 2 km/h increase in set speed. Each subsequent tap of the lever results in an increase of 2 km/h.

If the lever is continually help up, the set speed will continue to increase until the lever is released, then the new set speed will be established.

To Decrease Speed

When the Electronic Speed Control is set, you can decrease speed by tapping the Speed Control lever down (-).

The speed decrement shown is dependant on the speed of U.S. (mph) or Metric (km/h) units:

U.S. Speed (mph)

Tapping the Speed Control lever down (-) once will result in a 1 mph decrease in set speed. Each subse- quent tap of the lever results in a decrease of 1 mph.

If the lever is continually held down, the set speed will continue to decrease until the lever is released, then the new set speed will be established.

Metric Speed (km/h)

Tapping the Speed Control lever down (-) once will result in a 2 km/h decrease in set speed. Each subse- quent tap of the lever results in a decrease of 2 km/h.

If the lever is continually held down, the set speed will continue to decrease until the lever is released, then the new set speed will be established.

94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To Accelerate For Passing

Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.

PARKING SENSORS IF EQUIPPED

They are located in the rear bumper and their function is to detect the presence of any obstacles near the rear part of the vehicle; they consequently inform the driver, through an intermittent acoustic signal.

Parking Sensors

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95

Activation/Deactivation

The sensors are automatically activated when reverse gear is engaged. As the obstacle behind the vehicle gets closer, the acoustic signal becomes more frequent.

Acoustic Signal

When reverse gear is engaged and there is an obstacle behind the vehicle, an acoustic signal is emitted which varies according to the distance of the bumper from the obstacle.

The frequency of the acoustic signal:

Increases as the distance between vehicle and obstacle decreases, culminating in a continuous acoustic signal when the distance is less than approximately 12 in (30 cm).

Decreases if the distance from the obstacle increases, until the signal ceases entirely.

Remains constant if the distance between vehicle and obstacle remains unchanged; if this situation concerns the side sensors, the signal will stop after approxi- mately 3 seconds to avoid, for example, indications in the event of manoeuvres along a wall.

If several obstacles are detected by the sensors, only the nearest one is considered.

96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Indications On Display If Equipped

When the sensors are activated, the screen appears on the display.

Obstacle presence and distance information is therefore provided both by the acoustic signal and the instrument panel display.

The system indicates a detected obstacle by displaying an arc in one or more positions according to the distance of the obstacle and its position in relation to the vehicle.

If an obstacle is detected in the rear central area, the display shows all the arcs in the rear central area, up to the one that corresponds to the position of the obstacle itself.

The signal is similar for obstacles in the rear left or right area.

The arc that corresponds to the position of the obstacle will flash.

The color on the display depends on the distance from and position of the obstacle.

The vehicle is close to the obstacle when the display shows a single constant arc and emits a continuous sound.

If there are several obstacles, the closest one is indicated.

Parking Sensors Screen

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97

Fault Indication

Parking sensor failures, if any, will be indicated when reverse is engaged by the switching on of the warn- ing light on the instrument panel together with the message on the display.

General Warnings

When parking, take the utmost care over obstacles that may be above or under the sensor.

Under certain circumstances, objects close to the vehicle are not detected by the system and could therefore cause damage to the vehicle or be damaged themselves.

Some conditions may influence the performance of the parking sensors:

The presence of ice, snow, mud or multiple layers of paint on the sensor surface may cause reduced sensi- tivity of the sensor itself and therefore reduce the system performance.

Mechanical interference (e.g washing the vehicle, rain, strong wind, hail) may cause the sensor to detect a non-existent obstacle (echo interference).

The presence of ultrasonic systems (e.g. pneumatic brake systems of trucks or pneumatic drills) near the vehicle could alter the signals sent by the sensor.

The variation in sensor position, caused by variation in ride (due to suspension component wear), changing tires, overloaded vehicle, or tuning that lowers the vehicle, for example, may affect parking sensor system performance.

98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: The sensor must be free from mud, dirt snow or ice in order for the system to operate correctly. Be careful not to scratch or damage the sensors while cleaning them. Avoid using dry, rough or hard cloths. The sensors must be washed using clean water, with the addition of car sham- poo if necessary. When using special washing equipment such as high pressure jets or steam cleaning, clean the sensors very quickly keeping the jet more than 4 in (10 cm) away. Also, do not apply stickers to the sensors.

CAUTION!

The Parking Sensor system is only a parking aid and it is unable to recognize every obstacle, includ- ing small obstacles. Parking curbs might be tem- porarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity

(Continued)

CAUTION! (Continued) The vehicle must be driven slowly when using the

Parking Sensor system in order to be able to stop in time when an obstacle is detected. It is recom- mended that the driver looks over his/her shoulder when using the Parking Sensor system.

WARNING!

Drivers must be careful when backing up even when using the Parking Sensor system. Always check care- fully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must con- tinue to pay attention while backing up. Failure to do so can result in serious injury or death.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99

POWER OUTLETS

Your vehicle is equipped with a 12 Volt (13 Amp) power outlet that can be used to power cellular phones, small electronics and other low powered electrical accessories.

The power outlet is located on the central tunnel, be- tween the two cup holders. It only operates with the ignition key at MAR-ON.

Front Power Outlet

Power Outlet Fuse Location

100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

To avoid serious injury or death: Only devices designed for use in this type of outlet

should be inserted into any 12 Volt outlet. Do not touch with wet hands. Close the lid when not in use and while driving the

vehicle. If this outlet is mishandled, it may cause an electric

shock and failure.

CAUTION!

Many accessories that can be plugged in draw power from the vehicles battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicles battery will discharge suffi- ciently to degrade battery life and/or prevent the engine from starting.

Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with greater caution.

After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicles battery.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101

CAUTION!

Do not exceed the maximum power of 180 Watts (15 Amps) at 12 Volts. If the 180 Watts (15 Amps) power rating is exceeded, the fuse protecting the system will need to be replaced.

Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty.

CIGAR LIGHTER AND ASH RECEIVER IF EQUIPPED

The cigar lighter and ash receiver are located on the central tunnel. To activate the cigar lighter, push the button down. After a few seconds the button automati- cally returns to its initial position, and the cigar lighter is ready for use.

NOTE:

Always check that the cigar lighter is switched off.

Do not connect devices with power higher than 180 W to the socket.

Do not damage the socket by using unsuitable adap- tors.

102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CUPHOLDER

A cupholder is located in the rear of the center console.

STORAGE

Seatback Storage

Located in the back of both the driver and passenger front seats are pockets that can be used for storage.

Center Console Cupholder

Drivers Side Seatback Storage

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103

Console Features

There is a cargo pouch storage area located between the driver and passengers seat.

Rear Compartment Storage

CAUTION!

To prevent possible damage, do not slam the deck- lid to close it. Use a firm downward push at the center of the decklid to ensure the decklid latch is fully engaged.

During normal vehicle operation, the luggage com- partment (located rear of the engine) can reach temperatures above 149 degrees. Do not transport objects in the luggage compartment that may be damaged at such temperatures. Do not place aero- sol cans in the luggage compartment.

Your vehicle is equipped with a storage area located under the decklid.Cargo Pouch Storage Location

104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Do not allow children to have access to rear storage compartment. Always close the hood when your

(Continued)

WARNING! (Continued) vehicle is unattended. Once in the rear storage com- partment, young children may not be able to escape. If trapped in the rear compartment, children can die from suffocation or heat stroke.

As a security measure, an internal decklid emergency release lever is built into the rear compartment storage latching mechanism. In a event of a person trapped inside the storage compartment, the decklid can be simply opened by pulling on the phosphorescent handle attached to the decklid latching mechanism.Decklid Emergency Release

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105

WARNING!

The maximum load limit for the luggage compart- ment (located rear of the engine), in addition to the kits provided, is 33 lbs. (15kg). Do not exceed the

(Continued)

WARNING! (Continued) maximum permitted load in the luggage compart- ment. When accessing the rear luggage compart- ment, do not come into contact with engine, or other components, that may be hot and could burn you if touched.

Access the luggage compartment only with the vehicle stationary. Before exiting the vehicle, you should always place the vehicle into FIRST gear or REVERSE, apply the parking brake, and remove the key from the ignition. Never leave the key fob in the vehicle or in a location accessible to children.

The decklid may drop suddenly, causing serious injury, if the supporting rod is not positioned correctly.

The decklid must always be closed properly, and the lock engaged, while the vehicle is in motions.

Rear Compartment Light

106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE