3jTech HSPA FWT WiFi AP Quick Setup Guide PDF

Download download
3jTech HSPA FWT WiFi AP Quick Setup Guide PDF
3Jtech Manual 3Jtech Modem Manual 3Jtech HSPA FWT WiFi AP Manual 3Jtech Modem Quick Setup Guide
Pages 4
Year 2013
Language(s)
English en
1 of 4
1 of 4

Summary of Content for 3jTech HSPA FWT WiFi AP Quick Setup Guide PDF

Page 1

Ver 1.0.0.3

Since 1988

1

Quick Setup Guide for HSPA FWT WiFi AP 1. HSPA FWT WiFi AP Packing List : Before you start installing the HSPA FWT WiFi AP, please verify that the package contains the following items:

One Set of HSPA FWT WiFi AP,

1x RJ45 Network Cable,

External 3G Antenna with 3M Antenna Cable,

RJ11 Phone Cable,

1x Power Adapter,

CD with Users Manual,

This Quick Setup Guide

NOTE: Please notify your sales representative immediately if any items listed above is missing or damaged.

2. Hardware Connection Settings 1) Connect PC to LAN port of your HSPA FWT WiFi AP using a RJ-45 cable. 2) Make sure the SIM card has inserted to the modem, and the modem is ready as well. 3) Connect the power cable to the power connector of your HSPA FWT WiFi AP. 4) For using the Fixed Wireless Terminal (FWT) function, connect an analog phone to the

PHONE port of your HSPA FWT WiFi AP using a RJ-11 cable.

Fig.1 The Connection of HSPA FWT WiFi AP

Page 2

Ver 1.0.0.3

Since 1988

2

3. LED Description of the Rear Panel

LED Color Status

POWER( ) Yellow Lit when +8V DC power is on and working.

LAN Link ( ) Yellow Lit when the cable connection with device exists. Flash when the data is transmitting. Off when no cable connection exists.

WLAN(Wireless LAN ) Yellow Lit when the WiFi function is enabled. Flash when the data is transmitting. Off when the WiFi function is disabled.

Pick Up/Hang Up ( ) Yellow Lit when picking up the connected analog phone. Off when hanging up the connected analog phone.

SMS( ) Yellow Lit when receiving any new SMS(s). Off at any status except the incoming of new SMS(s).

3G PPP Status ( ) Yellow Lit when dialup is connected. Flash when the data is transmitting. Off when dialup is disconnected.

6 Cellular Signal Strength LEDs Low ( )

Yellow

All 6 LEDs lit when the signal strength is good. (The LEDs lit would decrease progressively upon the signal strength)

Medium ( )

High ( )

Page 3

Ver 1.0.0.3

Since 1988

3

4. Software Connection Settings Refer to the following sections to set up the HSPA FWT WiFi AP. Before the setup, please confirm that the LAN port of the AP has been connected with the PC via RJ-45:

Set up 3G Settings for the HSPA FWT WiFi AP 1. Please connect your computer to the HSPA FWT WiFi APs LAN port. 2. Initiate your Internet Explorer, and type in the address 10.10.10.254 3. Please input admin as the user name and the password. Click OK button to enter

APs setup page.

4. Once you are in the setup page, please select Internet Settings and enter WAN section of the setup.

5. In 2G/3G ISP SETTINGS, please contact your ISP for the dialup settings. User must enter Access Point Name (APN), Dial Number, Username and Password. Besides, you must enter PIN code if you had set up before for the SIM card.

Please ask your ISP for

required information

Page 4

Ver 1.0.0.3

Since 1988

4

6. Click on Apply after completing the setup. Wait 30 seconds around to have the new

settings taken effect.

7. You can check if the HSPA FWT WiFi AP is online by clicking on the Management / Status function. The information should be displayed under the Internet Configurations section.

5. Restore Factory Default Settings HSPA FWT WiFi AP provides a RESET button that will be easy for users to reset the AP to default. The button is located at the front panel of the AP (See the figure below). Reset steps are as follows:

(1) Press the RESET button 2 seconds around.

(2) All LEDs on the rear panel will flash 5 times.

(3) The AP will start to reboot.

NOTE: Disconnecting the power before resetting (which takes about 60 seconds) is complete might permanently

destroy the firmware. In this case of a damaged firmware, the unit will

Manualsnet FAQs

If you want to find out how the HSPA FWT WiFi AP 3Jtech works, you can view and download the 3jTech HSPA FWT WiFi AP Quick Setup Guide on the Manualsnet website.

Yes, we have the Quick Setup Guide for 3Jtech HSPA FWT WiFi AP as well as other 3Jtech manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Setup Guide should include all the details that are needed to use a 3Jtech HSPA FWT WiFi AP. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the 3jTech HSPA FWT WiFi AP Quick Setup Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This 3jTech HSPA FWT WiFi AP Quick Setup Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download 3jTech HSPA FWT WiFi AP Quick Setup Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print 3jTech HSPA FWT WiFi AP Quick Setup Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the 3jTech HSPA FWT WiFi AP Quick Setup Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.