3jTech wifiCAMit Quick Installation Guide PDF

Ver 1.0.0.4

Since 1988

1

Quick Installation Guide for wifiCAMit

1. wifiCAMit packing list : Before you start installing wifiCAMit, please verify that the package contains the following items:

One Set of wifiCAMit IP Camera

1x RJ45 Network Cable

1x Power Adapter

CD with Setup Software, Users Manual and this Quick Installation Guide

Desktop / Wall & Ceiling Mount Strut

NOTE: Please notify your sales representative immediately if any items listed above is missing or damaged.

wifiCAMit has wired and wireless operation modes. The default mode is wired. One would

need to set the wireless mode from wired mode. The follows are the installation steps for wired

mode.

2. Connecting the wifiCAMit to your existing router 1) Connect wifiCAMit to Ethernet port of your existing router using the RJ45 cable.

2) Connect the power cable to RJ12 jack of the wifiCAMit.

3) Insert CD to your PC connecting to the same router to install eCAMit Deluxe AP.

(Please refer to Section 3.)

4) Execute eCAMit Deluxe AP, the camera will automatically show up on Camera List.

5) Double click the camera to view.

6) Personalize your camera:

Move the mouse to the camera and click on the right button to set:

1. Public Password (Default is blank. Keep it blank if you would like the camera to be open

to the public.)

2. Supervisor Password (Default is blank. It is suggested to set this level of password.)

3. Camera Name (Default is my camera.)

RJ45 Connector

RJ12 Connector

Ver 1.0.0.4

Since 1988

2

NOTE : wifiCAMit is a plug and play IP camera if you are using a router. If you do not have a router, please skip this

section and refer to the Appendix B in wifiCAMit Users Guide for the advanced network settings. If you are

using 3JTech's Dedicated Wifi Router (DWR), please use another Quick Installation Guide: "Quick

Installation Guide for wifiCAMit with DWR".

3. Install the eCAMit Deluxe Software

1) Insert CD and install eCAMit Deluxe to

your PC or download the AP from:

http://www.3jtech.com/downloads.htm

for T series IP cameras. For CD

installation, please click on Install

eCAMit Deluxe" and follow the wizard.

For Internet downloaded software,

please unzip the files, and execute file Setup.exe and follow the wizard.

NOTE: If you have eCAMit Deluxe already on your PC, you do not need to install the software again.

Switch the Wired/Wireless Mode for the Camera The default mode of wifiCAMit is wired. The camera needs to be switched into the wireless

mode if the user would like to be independent of the RJ45 cable. In order to set the WIFI mode,

you would need to know the encryption method, SSID and WEP key of your WIFI Access Point.

Please refer to your WIFI Access Point User's Manual for these. Usually one could access the

Access Point by http://192.168.1.1 with the administrator password to find out these

parameters.

The procedures of the wireless setup are as

follows:

1) Run the eCAMit Deluxe software.

2) Click the Settings button next to the image

window.

3) Please move to Device Setting stage by

pressing >> button to do the wireless settings

of the camera.

Ver 1.0.0.4

Since 1988

3

4) Since the wifiCAMit is under the Wifi Access Point, one

would need to select "Infrastructure"

5) Please input the SSID and WEP key according to your

wireless Access Point / Router.

6) Click the Finish button to save the new settings and

exit the setting window.

7) Remove the power cable of the camera and RJ45 cable.

8) Switch the button located at the left side of the camera

(See the figure below) into Wireless positionandplug

in the power cable again.

9) After completing the above settings, the user will be able to view and set up the camera

wirelessly.

View Camera via eCAMit Deluxe

1) To view the camera, please start eCAMit Deluxe software.

2) Select the language you would like, then, the camera in the local LAN will be displayed

automatically on Camera List. You also can click on Add function if the cameras are

located remotely and not connected to the same router of the PC running eCAMit Deluxe.

WIRELESS

WIRED

Ver 1.0.0.4

Since 1988

4

3) When the add window appears, please enter the camera ID, which is the last 8 digits of the

MAC address of wifiCAMit. (Camera ID can be found on the back of your wifiCAMit unit.)

Click on Search when done, if your camera is online, the details should appear

automatically. Click OK to add this camera searched to Camera List.

4) Double click on th