Contents

Epson PowerLite 83+ User's Guide PDF

1 of 120
1 of 120

Summary of Content for Epson PowerLite 83+ User's Guide PDF

PowerLite

822+/83+ Multimedia Projector

Users Guide

2

Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this Users Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporations operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Trademarks Epson and Instant Off are registered trademarks, and Epson Exceed Your Vision is a trademark of Seiko Epson Corporation.

PowerLite and PrivateLine are registered trademarks; Duet and SizeWise are trademarks; and Epson Store and Extra Care are service marks of Epson America, Inc.

Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

The contents of this manual are subject to change without notice.

2007 Epson America, Inc. 12/07

C

3

Contents

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Getting the Most from Your Projector . . . . . . . . . . . . . . . . . 8 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 9

Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 9 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Projector Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

1 Setting Up the Projector . . . . . . . . . . . . . . . . . . . . 15 Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Other Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting with the VGA Cable . . . . . . . . . . . . . . . . . 18 Connecting with a VGA-5BNC Cable. . . . . . . . . . . . . 20 Connecting an External Monitor . . . . . . . . . . . . . . . . . 21 Playing Sound Through the Projector . . . . . . . . . . . . . 22 Connecting External Speakers . . . . . . . . . . . . . . . . . . . 23

Connecting to Video Sources . . . . . . . . . . . . . . . . . . . . . . . 24 Connecting a Composite Video Source . . . . . . . . . . . . 25 Connecting an S-Video Source . . . . . . . . . . . . . . . . . . 26 Connecting an RGB Video Source. . . . . . . . . . . . . . . . 27 Connecting a Component Video Source . . . . . . . . . . . 28 Playing Sound Through the Projector . . . . . . . . . . . . . 29

4

2 Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 34

Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 34 Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 36 What To Do If You See a Blank Screen . . . . . . . . . . . . . 36

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Focusing and Zooming Your Image . . . . . . . . . . . . . . . . 38 Adjusting the Height of Your Image . . . . . . . . . . . . . . . 39 Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 40 Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . 40 Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 41

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 42

3 Using the Remote Control . . . . . . . . . . . . . . . . . . . 43 Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 44

Switching Between Picture Sources . . . . . . . . . . . . . . . . 44 Adjusting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 45 Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 46 Stopping Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Zooming Your Image. . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Changing the Images Aspect Ratio . . . . . . . . . . . . . . . . 47

Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4 Fine-tuning the Projector. . . . . . . . . . . . . . . . . . . . 49 Using the Projectors Menu System . . . . . . . . . . . . . . . . . . . 50

Changing Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . 51 Adjusting Colors and Clarity . . . . . . . . . . . . . . . . . . . . . . . . 52 Adjusting the Input Signal . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 56 Selecting Projector Setup Options . . . . . . . . . . . . . . . . . . . . 58 Selecting Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Viewing Lamp Usage and Other Information. . . . . . . . . . . . 61

5

Using the Projectors Security Features. . . . . . . . . . . . . . . . . 62 Creating Your Own Screen Logo. . . . . . . . . . . . . . . . . . 64 Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Turning On the Password and Users Logo . . . . . . . . . . 66 Starting the Projector with a Password. . . . . . . . . . . . . . 67 Disabling the Projectors Buttons . . . . . . . . . . . . . . . . . 68 Installing Security Locks . . . . . . . . . . . . . . . . . . . . . . . . 68

Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . . . . 69

5 Maintenance and Transportation . . . . . . . . . . 71 Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 72 Cleaning and Replacing the Air Filter . . . . . . . . . . . . . . . . . 72 Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 78

6 Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Using On-Screen Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 What To Do When the Lights Flash . . . . . . . . . . . . . . . . . . 80 Solving Problems with the Image or Sound . . . . . . . . . . . . . 82 Solving Password Problems . . . . . . . . . . . . . . . . . . . . . . . . . 87 Solving Problems with the Remote Control . . . . . . . . . . . . . 88 Solving Network Problems. . . . . . . . . . . . . . . . . . . . . . . . . . 89 Where To Get Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Speak to a Support Representative. . . . . . . . . . . . . . . . . 90

7 Monitoring the Projector Over a Network. . 91 Installing the Network Software. . . . . . . . . . . . . . . . . . . . . . 92

Windows System Requirements . . . . . . . . . . . . . . . . . . 92 Installing the Software on a Windows System . . . . . . . . 92

Connecting to the Network . . . . . . . . . . . . . . . . . . . . . . . . . 93 Selecting Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 94

Using Projector E-mail Alerts . . . . . . . . . . . . . . . . . . . . 95

6

Using EMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Opening and Closing EMP Monitor . . . . . . . . . . . . . . . 96 Registering a Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Monitoring Your Projector . . . . . . . . . . . . . . . . . . . . . . 97 Using E-mail Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Using a Browser to Monitor the Projector . . . . . . . . . . . . . 101

A Technical Specifications . . . . . . . . . . . . . . . . . . . . 103 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Projection Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Safety and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . 106 Compatible Computer Display Formats. . . . . . . . . . . . . . . 107

B Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 111 FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 113

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

W

7

-

Welcome The PowerLite 822+/83+ is a portable projector that weighs less than 7 pounds. The projector offers 2600 ANSI lumens (822+) or 2200 ANSI lumens (83+) of brightness. From classrooms to boardrooms, your full-color presentations and videos will be bright and vibrant even in ordinary indoor lighting.

Images are displayed at a native resolution of 1024 768 pixels. Epson 3LCD technology ensures accurate color and remarkable saturation, even in well-lit rooms.

You can connect the projector to a wide range of computers, including IBM-compatible PCs and laptops, Apple Macintosh, PowerPC and Intel Core Macintosh computers, PowerBook computers, and many iMac and iBook series systems. With Epsons patented SizeWise technology, the projector supports computer displays ranging from VGA through UXGA.

You can use any of the following video sources: HDTV, VCR, DVD player, gaming console (such as Microsoft Xbox, Sony PlayStation 3, and Nintendo Wii), camcorder, or digital camera. The projector supports NTSC, PAL, and SECAM video formats.

You can also connect the projector to a LAN (local area network) so you can monitor the projector from a remote network computer using the included EMP Monitor software.

You can connect up to four devices to the projector at the same time. With the projectors Source Search button, you dont even have to identify your input source. Just press the button until you see the image you want on the screen.

8 Welcome

To prevent unauthorized use of the projector, you can assign a password, create a user logo which is displayed at startup to identify the projector, and disable the projectors buttons through a full or partial Operation Lock feature. For more information about security features, see page 62.

Getting the Most from Your Projector Depending on your presentation, you can take advantage of any or all of these options:

Connecting to a laptop or other computer If you want to connect the projector to a laptop or desktop computer, see page 18. For additional presentation control, you can connect an external monitor to view the presentation on your computer simultaneously.

Connecting to video sources You can connect a DVD player, VCR, HDTV, camcorder, digital camera, and other video sources to your projector. See page 24 for instructions.

Using the remote control The remote control lets you switch from computer to video sources, zoom in on part of your image, freeze or mute the presentation, and adjust many other projector features. For details, see Chapter 3.

Enhancing sound in your presentation By connecting your projector to external speakers, you can enhance the audio impact of your presentations.

Welcome 9

Using Your Documentation In addition to this manual, your documentation includes a Quick Setup sheet, warranty brochures, and an Epson PrivateLine Support card.

The Quick Setup sheet gives instructions to quickly set up your projector and connect it to a computer or video device.

This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it:

Warnings must be followed carefully to avoid bodily injury.

Cautions must be observed to avoid damage to your equipment.

Notes contain important information about your projector.

Getting More Information

Need tips on giving presentations? How about quick steps for setting up your projector? Heres where you can look for help:

www.presentersonline.com Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art, and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the Presenters Cluband its free.

Built-in help system Press the Help button on the remote control or projector to get quick solutions for common problems. See page 80 for details.

epson.com/support Download FAQs (frequently asked questions) and e-mail your questions to Epson support on the PowerLite 822+ or PowerLite 83+.

If you still need help after checking this Users Guide and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on your PrivateLine Support card. See page 89 for more information.

note The instructions here apply to the PowerLite 822+ and PowerLite 83+ projectors and cover both projectors, unless noted.

10 Welcome

Registration and Warranty Your projector comes with a basic carry-in warranty and an international warranty that let you project with confidence anywhere in the world. For details, see the warranty brochures that came with your projector.

In addition, Epson offers Extra CareSM Road Service at no additional charge. In the unlikely event of an equipment failure, you wont have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually within one business day. See the Extra Care Road Service brochure for details.

To register, complete the registration form that came with your projector and mail it to Epson. Or register your product online using your projector CD, or at:

http://www.epson.com/webreg

Registering also lets you receive special updates on new accessories, products, and services.

Welcome 11

Unpacking the Projector After unpacking the projector, make sure you have all these items:

Save all packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when you send the projector to another location. See page 78 for transportation instructions.

Projector Remote control and batteries

VGA computer cable Power cord

Password Protected Sticker

PDF User's Guide CD-ROM

Projector software CD-ROM

12 Welcome

Projector Parts

Control panel

Lamp cover

Air exhaust vent

Front adjustable foot Foot release lever

Remote control sensor

Focus ring

Zoom ring

Security slot

Monitor Out port (for Computer1 port output only)

Computer 1 and 2 (Component Video) portsS-Video port

Video portLAN port

Remote control sensor

Speaker

Audio L-R input ports

Rear adjustable foot

Power inlet

A/V mute slide lever

A/V mute slide

RS-232C serial port

Audio 1 and 2 input ports

Audio Out port

Air filter

Hole for ceiling mount bracket

Holes for ceiling mount bracket

Security lock slot

Front

Back

Bottom

Welcome 13

Additional Components Depending on how you plan to use the projector, you may need additional components:

To receive an S-Video signal, you need an S-Video cable. One is usually provided with your video device or you can purchase it from Epson. See page 14.

To receive a component video signal from a VCR or other video device, you need a D-sub, 15-pin, component-to-VGA video cable, which is available from Epson. See page 14.

Some older PowerBooks and Macintosh desktop models may need a Macintosh video adapter; see your computer dealer. Older iMac systems may need a special adapter to provide a VGA output port; see your computer dealer.

To receive an audio signal, you need a commercially available audio cable; see your computer or electronics dealer.

Control Panel

Indicate projector status

Turns projector on and off

Searches for source image

Opens menu system

Left/right arrows and Volume down/up

Up/down arrows and keystone correction

Opens help system

Cancel/exit

Automatically adjusts computer images

14 Welcome

Optional Accessories To enhance your use of the projector, Epson provides the following optional accessories:

You can purchase screens, carrying cases, or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).

Product Product number

Replacement lamp V13H010L42

Air filter set (includes 2 filters) V13H134A13

Component-to-VGA video cable S-Video cable

ELPKC19 ELPSV01

Distribution amplifier ELPDA01

50-inch portable screen (4:3 aspect ratio) 60-inch portable pop-up screen (4:3 aspect ratio) 80-inch portable pop-up screen (4:3 aspect ratio) 83.6-inch hanging pull-down screen

(4:3 aspect ratio) Duet Ultra Portable Projector screen

(4:3 and 16:9 aspect ratio)

ELPSC06 ELPSC07 ELPSC08 ELPSC09

ELPSC80

ELPDC05 high resolution document imager V12H162020

Kensington security lock ELPSL01

Ceiling mount (gyro lock with suspension adapter) False ceiling plate Suspension adapter Security bracket/cabling for gyro lock mounts Adjustable ceiling channel

ELPMBUNI ELPMBFCP ELPMBAPL ELPMBSEC ELPMBACC

note To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer referral in Canada).

1

15

1

Setting Up the Projector This chapter tells you how to set up the projector and connect it to a computer or video source. You can connect up to four devices simultaneously: four video sources, or two computer and two video sources.

Youll find instructions for the following in this chapter:

Positioning the projector

Connecting to a computer

Connecting to video sources

16 Setting Up the Projector

Positioning the Projector Before connecting the projector, you need to decide where to place it. If youre setting up the projector yourself and it isnt already installed in the room youre using, youll probably want to place it on a table in front of the screen, as shown.

This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it. Try to leave as much space as possible between the projector and the screen to get a good-size image.

Place the projector somewhere between 3 and 30 feet from the screen. Use the figure below to help you determine exactly how far. Image size increases with distance, but can vary depending on how youve adjusted the optical zoom and other settings.

Also keep these considerations in mind:

Place the projector on a sturdy, level surface.

Make sure there is plenty of space for ventilation around and under the projector. Do not set the projector on top of loose papers that could block the vents under the projector.

Make sure the projector is within 6 feet (2 meters) of a grounded electrical outlet or extension cord.

note You can download the Projection Distance Calculator program from the Drivers and Downloads section of Epsons web site: www.epson.com/support

28 to 34 ft (4:3) 31 ft (16:9; wide only)

5.6 to 6.8 ft (4:3) 6.1 to 7.3 ft (16:9)

2.7 to 3 ft (4:3) 3 to 3.6 ft (16:9)

Setting Up the Projector 17

Try to place the projector directly in front of the center of the screen, facing it toward the screen squarely. If the projector isnt positioned this way, the image will be keystone shaped, instead of square or rectangular.

If you place the projector below the level of the screen, youll have to tilt it up by extending the front adjustable foot, as described on page 39. This also causes the image to lose its rectangular shape. You can adjust the shape using the buttons on the projector (see page 40), or using the projectors menu system (see page 49).

The Auto Keystone feature corrects the distortion automatically. See page 57 for more information about Auto Keystone correction. If necessary, you can adjust the image shape manually as described on page 40.

Other Installations

You can also project from behind the screen or from the ceiling, with the projector mounted upside-down:

To project from overhead, youll need the optional ceiling mount hardware. (See page 14 for ordering information.) Youll also need to select Front/Ceiling or Rear/Ceiling for the Projection option in the Extended menu. To project from the rear, select Rear. See page 58 for more information.

Front/ceiling projectionRear projection (using a translucent screen)

Rear/ceiling projection (using a translucent screen)

18 Setting Up the Projector

Connecting to a Computer You can connect the projector to any computer that has a standard VGA or BNC monitor port, including PC notebook and laptop computers, Macintosh PowerBooks and iBooks, and hand-held devices.

Follow the instructions in this section to:

Connect the projector to your computer with the VGA cable included with the projector.

Connect the projector to your computer with a commercially available VGA5BNC cable.

After connecting the projector to your computer, you may also want to:

Connect a monitor to the projector so you can view your presentation close-up as well as on-screen (not necessary if youre using a laptop); see page 21.

Connect the projector to your computer with a commercially available audio cable to play computer audio; see page 22.

Connecting with the VGA Cable

Follow these instructions to connect to your computer with the VGA cable that came with your projector. Before you start, make sure your computer and the projector are turned off.

1. If you are connecting the projector to a desktop computer, disconnect the monitor cable from your computer.

2. Locate the VGA computer cable that came with the projector.

note If you have an iBook with an RCA video-out port, follow the instructions for connecting to a video device on page 25.

VGA computer cable

Setting Up the Projector 19

Connect one end of the cable to the projectors Computer1 or Computer2 port.

3. Connect the other end of the cable to your computers video-out or monitor port.

If youre using a PowerBook or iBook and you cant connect the cable, you may need to use an optional Macintosh video adapter; see your computer dealer.

4. If you connected the computer to the Computer1 port and you want to view the display simultaneously on your computer monitor and the projector screen, see Connecting an External Monitor on page 21.

5. To play audio from your computer through the projector speakers, see Playing Sound Through the Projector on page 22.

6. Tighten the screws on the connectors.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

If more than one device is connected to the projector, select the correct source after projection starts by pressing the Source Search button on the projector or remote control. See page 36.

Computer1 and Computer2 ports

20 Setting Up the Projector

Connecting with a VGA-5BNC Cable

If your computer provides video output through BNC connectors, follow these instructions to connect the projector to your computer with an optional VGA-5BNC cable. Before you start, make sure your computer and the projector are turned off.

1. Disconnect the monitor cable from your computer.

2. Connect the cables VGA connector to the projectors Computer1 or Computer2 port.

3. Connect the BNC connectors to your computers BNC ports.

4. If you want to view the display simultaneously on your computer monitor and the projector screen, see Connecting an External Monitor on page 21.

5. To play audio from your computer through the projector speakers, see Playing Sound Through the Projector on page 22.

6. Tighten the screws on the VGA connector.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

If more than one device is connected to the projector, select the correct source after projection starts by pressing the Source Search button on the projector or remote control. See page 36.

VGA-5BNC cable

Computer1 and Computer2 ports

Setting Up the Projector 21

Connecting an External Monitor

If you want to see your presentation close-up as well as on the projection screen, you can connect an external monitor to the projector. This lets you view images on your computer monitor while the projector is in standby mode (plugged in but not turned on) and check your presentation or switch between picture sources even if youve pressed the A/V Mute button on the remote control to turn off projection on the screen.

Simultaneous display is possible only when the computer is connected to the projectors Computer1 port.

Make sure the projector and computer are off. Then connect the monitors cable to the projectors Monitor Out port, as shown:

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

note Some LCD monitors may not be able to display the image correctly. If you have trouble displaying the image, connect a multiscan monitor. If youre projecting computer images, make sure the computers refresh rate is set to 65 Hz or greater.

22 Setting Up the Projector

Playing Sound Through the Projector

You can connect a commercially available 3.5 mm stereo mini-jack audio cable to take advantage of the projectors built-in speaker. You can obtain the audio cable from a computer or electronics dealer.

1. Connect one end of the 3.5 mm stereo mini-jack audio cable to the corresponding Audio1 or Audio2 jack on the projector.

2. Connect the other end of the audio cable to your laptops headphone jack or audio-out jack, or your desktops

speaker or audio-out port.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

Audio1 and Audio2 jacks

Setting Up the Projector 23

Connecting External Speakers

You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projectors built-in speaker system is disabled.

1. Locate the appropriate cable to connect your speakers.

Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter.

2. Connect the stereo mini-jack end of the audio cable to the Audio Out port on the projector.

3. Connect the other end of the cable to your speakers.

When you use external speakers with the projector, you can use the or volume buttons on the projector or the Vol- and Vol+ buttons on the remote control to adjust the volume. First, you need to select the maximum volume on the external speakers. Then you can use the projector or remote control buttons for further adjustments.

24 Setting Up the Projector

Connecting to Video Sources You can connect a DVD player, VCR, camcorder, digital camera, gaming console, or any other compatible video source to your projector. You can connect up to four video devices at one time.

The projector supports HDTV, SDTV, NTSC, PAL, and SECAM, and automatically detects the video format. It can receive composite video, S-Video, RGB video, and component video. The type of cable you need depends on the video source:

For composite video, use a commercially available RCA A/V cable. See page 25.

For S-Video, use the S-Video cable supplied with your video device or order one from Epson. See page 26.

For RGB video, use the VGA computer cable included with the projector. See page 27.

For component video, youll need the optional Epson component-to-VGA video cable. See page 28.

After connecting your video device to the projector, you may want to connect an audio cable to play sound from your video equipment through the projectors built-in speaker or external speakers. See page 29 for instructions.

note The projector does not support TV antenna cable F connectors.

Setting Up the Projector 25

Connecting a Composite Video Source

If youre connecting a composite video device, use a commercially available RCA A/V cable. Before starting, make sure the projector and your DVD player or other video source are turned off.

1. Connect the yellow RCA plug on one end of the cable to the projectors yellow Video port.

2. Connect the yellow plug on the other end of the cable to the video-out port on your video source.

3. To play sound through the projector, follow the instructions beginning on page 29.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

If more than one device is connected to the projector, select the correct source after projection starts by pressing the Source Search button on the projector or remote control. See page 36.

Video port

26 Setting Up the Projector

Connecting an S-Video Source

If your video source has an S-Video jack, you can use it to project a higher quality video image. Youll need an S-Video cable, which is usually provided with your video source, or you can purchase one from Epson (part number ELPSV01). See page 14 for ordering information.

Before starting, make sure the projector and your DVD player or other video source are turned off.

1. Insert one end of the S-Video cable into the projectors S-Video port and the other end into the S-Video output port of your video source.

2. To play sound through the projector, follow the instructions beginning on page 29.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

If more than one device is connected to the projector, select the correct source after projection starts by pressing the Source Search button on the projector or remote control. See page 36.

S-Video port

Setting Up the Projector 27

Connecting an RGB Video Source

Follow these instructions to connect the projector to a video player or satellite receiver that has an RGB video output port using the VGA computer cable that came with the projector.

Before starting, make sure the projector and your DVD player or other video source are turned off.

1. Connect one end of the VGA computer cable to the Computer1 or Computer2 port on the projector.

2. Connect the other end to the video port on your player.

3. To play sound through the projector, follow the instructions beginning on page 29.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

If more than one device is connected to the projector, select Computer 1 or Computer 2 as the source after projection starts by pressing the Source Search button on the projector or remote control. See page 36.

Computer1 and Computer2 ports

28 Setting Up the Projector

Connecting a Component Video Source

If your video source has component video connectors, you can use them to project a higher quality video image. Youll need a component-to-VGA video cable, which can be purchased from Epson (part number ELPKC19). See page 14 for ordering information.

Before starting, make sure the projector and your DVD player or other video device are turned off.

1. Connect the 15-pin VGA connector end of the component-to-VGA video cable to the projectors Computer1 or Computer2 port.

2. Insert the three component ends of the component-to-VGA video cable into the color-coded video output ports on your video source, usually labelled Y, Pb, Pr or Y, Cb, Cr.

3. To play sound through the projector, follow the instructions beginning on page 29.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

If more than one device is connected to your projector, select Computer1 or Computer2 as the source by pressing the Source Search button on the projector or the remote control. See page 36.

Computer1 and Computer2 ports

Setting Up the Projector 29

Playing Sound Through the Projector

The projector has a built-in speaker with a maximum output of 10 W. You can play sound from your video equipment through the projectors speaker if your video device has an audio output port.

For RCA-Type Audio Output Ports

Most video devices have an RCA-type audio output port. In this case, use a commercially available RCA-type audio cable to connect the projector to your video source:

1. Connect one end of the RCA audio cable to the L-Audio-R jacks on the projector.

2. Connect the red and white plugs on the other end of the RCA audio cable to the corresponding color-coded audio output port on your video source.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

L-Audio-R jacks

30 Setting Up the Projector

For Stereo Mini-Jack Audio Output Ports

Some video devices, especially camcorders, may have a stereo mini-jack audio output port. To connect to the L-Audio-R input jacks when using the S-Video or Video port, use a commercially available stereo mini-jack audio adapter cable (3.5-mm stereo miniplug to two male RCA plugs) to connect to the projector.

1. Connect one end of the audio adapter cable to the L-Audio-R jacks on the projector.

2. Connect the other end of the audio adapter cable to your video devices audio output port.

If you dont need to make any other connections, you can plug in your projector and turn it on. See page 34 for instructions.

L-Audio-R jacks

Setting Up the Projector 31

Connecting External Speakers

You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projectors built-in speaker system is disabled.

1. Locate the appropriate cable to connect your speakers.

Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter.

2. Connect the stereo mini-jack end of the audio cable to the Audio Out port on the projector.

3. Connect the other end of the cable to your speakers.

When you use external speakers with the projector, you can use the or volume buttons on the projector or the Vol- and Vol+ buttons on the remote control to adjust the volume. First, you need to select the maximum volume on the external speakers. Then you can use the projector or remote control buttons for further adjustments.

32 Setting Up the Projector

2

33

2

Projecting Once youve set up the projector, youre ready to turn it on, adjust the image, and give your presentation.

Although you can operate the projector without it, the remote control lets you use additional features. See Chapter 3 for instructions on using the remote. This chapter covers the following:

Turning on the projector and other equipment

Adjusting the image

Adjusting the volume

Shutting down the projector

34 Projecting

Turning On Your Equipment Make sure your projector and other equipment are set up and connected correctly, as described in Chapter 1. Then turn on your projector, as described below.

If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually. See page 36.

Turning On the Projector

Follow these steps to plug in and turn on the projector:

1. Open the A/V Mute slide (lens cover).

2. Connect one end of the power cord to the projectors power inlet.

Projecting 35

3. Connect the other end to an electrical outlet. The P Power light on top of the projector turns orange, indicating that the projector is receiving power but not yet turned on.

4. Turn on your computer or video source if you have not already.

5. Press the P Power button on the projector or on the remote control to turn it on.

The projector beeps and the P Power light flashes green as the projector warms up. The projector lamp comes on in about 5 seconds and the P Power light stays green.

If youre using a computer, you should see your computer display projected after a moment or two. If not, you need to select the image source. See page 36.

(With Windows, if you see a message saying that it has found a plug-and-play monitor, click Cancel.)

If youre projecting a video, you may need to press the Source Search button on the projector or remote control to switch to your video source. Then press the Play button on your DVD player or other device.

If you are prompted to enter a password, see page 67.

To focus and adjust the image, see page 38. If a projected image fails to appear, see What To Do If You See a Blank Screen on page 36.

When youre done, shut down the projector as described on page 42.

note If you are using the remote control for the first time, be sure to insert the batteries as described on the Quick Setup poster.

Power button

warning Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.

36 Projecting

Selecting the Image Source

Selecting the image source lets you switch between images input from different pieces of equipment connected to the projector (such as a computer and DVD player). If you dont see the image you want, press the Source Search button on the remote control or projector until the correct device image is projected. If a projected image fails to appear, see the next section for help.

Once you see your image, turn to page 38 for instructions on focusing and making other image adjustments.

What To Do If You See a Blank Screen

If you see a blank screen or a blue screen with the message No Signal after turning on your computer or video source, try the following:

Make sure the cables are connected correctly, as described in Chapter 1.

Make sure the P Power light is green and not flashing and the A/V Mute slide is open.

Make sure youve selected the correct image source; see the previous section. Allow a few seconds for the projector to sync up after pressing the button.

Check the Signal menu to make sure the correct input source is selected. See page 54.

If youre using a PC laptop: Hold down the Fn key and press the function key that lets you

display on an external monitor. It may have an icon such as or it may be labelled CRT/LCD. Allow a few seconds for the projector to sync up after pressing it. Check your laptops manual or online help for details.

On most systems, the or CRT/LCD key lets you toggle between the LCD screen and the projector, or display on both at the same time.

note The name of the selected image source appears briefly in the upper right corner of the screen.

Projecting 37

If youre projecting from a laptop, and you dont see the same image on the projection screen and computer screen, check your monitor settings to make sure both the LCD screen and the external monitor port are enabled.

From the Control Panel, open the Display utility. Click the Settings tab, then click Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled. See your computers documentation or online help for details.

If youre using a Macintosh laptop with OS X: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps:

1. From the Apple menu, select System Preferences, then click Display or Displays.

2. Select VGA Display or Color LCD, click Arrange or Arrangement, and make sure Mirror Displays is checked.

Click here

Select Mirror Displays

38 Projecting

Adjusting the Image Once you see your image, youll need to make certain adjustments:

To focus or zoom your image, see below.

If the image is too high or too low, you can reposition it. See page 39.

If the image isnt square, see page 40.

To adjust image brightness, see page 40.

If a computer image displays incorrectly, see page 41.

You can make many other adjustments to the imagesuch as changing the brightness, contrast, and aspect ratiousing the projectors menu system. See Chapter 4 for more information.

Focusing and Zooming Your Image

Rotate the focus ring to sharpen the image, and the zoom ring to reduce or enlarge the image.

You can also change the image size by moving the projector closer to or farther away from the screen. You can use the E-Zoom buttons on the remote control to zoom in on a portion of the image. See page 47 for instructions.

Focus

Zoom

Projecting 39

Adjusting the Height of Your Image

If the image is too high or low, you can correct it by adjusting the projectors front foot.

1. Stand behind the projector. Press up on the blue foot release lever and lift the front of the projector to extend the front adjustable foot.

2. Once the image is positioned where you want, release the lever to lock the foot in position.

The projector automatically corrects images that are distorted when the projector is tilted up or down (up to a 30 tilt). The Keystone window appears on the screen while the projector makes the correction. If the projected image still isnt rectangular, follow the instructions in the next section.

40 Projecting

Adjusting the Image Shape

If the projector is tilted up or down, the images that are displayed will be distorted. To correct the distortion or keystone shape, do one or more of the following:

If your image looks like or , youve placed the projector off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely.

If your image looks like or , you need to adjust the keystone correction value. Press the or buttons on the projector to correct the shape of the image. After correction, your image will be slightly smaller.

You may need to turn on Auto Keystone. See page 56 for instructions.

You can also make keystone adjustments using the projectors Settings menu. See page 56.

Adjusting the Brightness

The brightness of an image depends on the source you are projecting and the amount of light in the room. If the image is too bright or not bright enough, here are two ways you can adjust it:

Change the Brightness setting in the Image menu. See page 53.

Select Low or High for the Brightness Control option in the Settings menu. (See page 57.) Low brightness mode extends the life of the lamp and decreases the fan noise.

Projecting 41

Correcting Computer Images

If youve connected a computer and the image doesnt look right, or it doesnt fit properly on the screen, press the Enter button on the projector or the Enter/Auto button on the remote control. This automatically resets the projectors tracking, sync, resolution, and position settings. You must be projecting a computer image for this button to have any effect. Additionally, if the Auto Setup option in the Signal menu is set to Off, the Auto function will not work. See page 55.

Adjusting the Volume You can use the Vol- and Vol+ buttons on the remote control to increase or decrease the volume.

You can also use the buttons on the projector to control the volume. Press the button to increase the volume, or the button to decrease it. A volume gauge appears on the screen while the volume is being adjusted.

note You can also adjust the volume using the projectors Settings menu. See page 56 for details.

You must adjust the volume separately for each input source.

Volume control buttons

42 Projecting

Shutting Down the Projector When youve finished using the projector, follow the recommended procedure to shut it down.

1. If youre using a computer, shut it down first; otherwise you may not be able to see your computers display to shut it down properly.

2. To turn off the projector, press the P Power button on the projector or remote control.

You see this confirmation message: (If you dont want to turn it off, press any other button or wait a few seconds until it disappears.)

3. Press the P Power button again. The projector beeps twice, the lamp is turned off, and the P Power light turns orange. (To turn the projector on again, press the P Power button.)

With Epsons exclusive Instant Off technology theres no cool-down period, so you can pack up and go immediately after turning off the projector.

4. Press up on the blue foot release lever and lower the projector to retract the front adjustable foot.

5. Close the A/V Mute slide.

6. Unplug the power cord.

7. Turn off and disconnect any equipment plugged into the projector.

8. If you wont be using the projector for awhile, store it in a protective case.

note When the projector has not received any input signals for 30 minutes, it automatically turns off the projector lamp and enters sleep mode. This conserves electricity, cools the projector, and extends the life of the lamp. If you are done using the projector, unplug the power cord. If you want to start projecting again, press the P Power button. You can turn sleep mode on or off through the Extended menu. See page 59.

Turn off this product when not in use to prolong the life of the projector.

caution To avoid damaging the projector or lamp, never unplug the power cord when the P Power light is green or flashing orange.

3

43

33

Using the Remote Control The remote control lets you access your projectors features from anywhere in the roomup to 20 feet away. For example, you can turn the projector on and off, freeze the presentation, zoom in on a portion of your image, and access the menu system. (The projector menus let you adjust many projector settings; see Chapter 4.)

When using the remote control, stand within 20 feet of the projector. Point the remote control either at the front or back of the projector or at the screen (the projectors front sensor can detect signals bounced off the screen). Press the button for the function you want to use.

This chapter covers the following information:

Controlling the picture and sound

Replacing the remote control batteries

44 Using the Remote Control

Controlling the Picture and Sound You can use the remote control to select your source, adjust the colors, temporarily turn off the picture and sound, freeze the action, or zoom in on the picture. Make sure you have set up your projector and connected any equipment as described in Chapter 1.

Switching Between Picture Sources

If youve connected your projector to more than one computer and/or video source, you can use the Source Search button on the projector or remote control to switch between the different sources.

After you select a source, the screen goes dark for a moment before the image appears. The name of the selected source (such as Computer1 or S-Video) appears briefly on the screen.

Source Search button

Using the Remote Control 45

Adjusting the Color Mode

You may want to adjust the color mode to select a different setting that is appropriate for the image youre projecting and the environment in which youre projecting it. Press the Color Mode button on the remote control.

If youre projecting computer or RGB video images, the default color mode is Presentation, which is appropriate for full-color presentations in bright rooms.

The following table lists the color modes available.

You can also use the projector menu system to change the color mode in the Image menu (see page 53).

Color mode Description

Photo Best for projecting still images with vivid color in a bright room (computer input only).

Sports Best for watching TV in a bright room (component, S-video, or composite video input only).

Presentation Use when youre projecting a full-color presentation in a bright room.

Text Use when youre projecting a black and white presentation in a bright room.

Theatre Use when projecting movies in a dark room.

Game Brightest mode, best for playing video games in a bright room.

sRGB Use when projecting computer images conforming to the sRGB color standard.

Blackboard Choose this fixed color mode when you need to project against a green blackboard.

Color Mode button

46 Using the Remote Control

Turning Off the Picture and Sound

Press the A/V Mute button on the remote control or use the A/V Mute slide on the projector to turn off the image and sound and darken your screen. This is useful if you want to temporarily re-direct your audiences attention without the distraction of a bright screen.

To turn off the picture and sound, press the A/V Mute button or close the A/V Mute slide on the projector. The screen goes dark.

To turn the image and sound back on, press the button again, or open the AV Mute slide.

You can create an image, such as a company logo or a picture, to display on the screen whenever you press the A/V Mute button. See page 64 for more information.

Stopping Action

Press the Freeze button to stop the action in your video or computer image and keep the current image on the screen. The sound will continue, however. Also, because the source continues to transmit signals, you wont resume the action from the point you paused it.

To restart the action, press the Freeze button again.

A/V Mute button

A/V Mute slide

Freeze button

Using the Remote Control 47

Zooming Your Image

Follow these steps to zoom in on a portion of the image:

1. Press the E-Zoom + button on the remote control.

You see a crosshair indicating the center of the zoom-in area.

2. Use the four arrow buttons on the remote control to position the crosshair in the area you want to enlarge.

3. Continue pressing the E-Zoom + button to enlarge the selected area up to 4 times.

4. While the image is enlarged, you can:

Use the arrow buttons to pan about.

Press the E-Zoom button to zoom out.

5. When youre done, press the ESC button to return to the original size.

Changing the Images Aspect Ratio

If youre projecting a widescreen format image, you can use the Aspect button on the remote control to change the aspect (width to height) ratio from 4:3.

You can change video images to 16:9 (widescreen format), or 16:9 (Up) or 16:9 (Down) (to accommodate subtitles or supertitles).

You can change computer images to 16:9 (widescreen format) or Normal

Press the Aspect button again to cycle through the available options.

You can also change the aspect ratio using the projectors Signal menu. See page 54 for details.

E-Zoom buttons

Arrow buttons

Aspect button

48 Using the Remote Control

Replacing the Batteries The remote control uses two AA alkaline batteries. Follow these steps when you need to replace them:

1. Press in the tab to remove the battery cover.

2. Remove the old batteries, then insert the new ones as shown.

3. Replace the battery cover. (It should click into place.)

caution When replacing batteries, take the following precautions:

Replace the batteries as soon as they run out. If a battery leaks, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.

Do not expose batteries to heat or flame.

Dispose of used batteries according to local regulations.

Remove the batteries if you wont be using the remote control for a long period of time.

note The remote control automatically shuts off when it detects a button being pressed more than 30 seconds. This conserves battery life. It can be helpful, for example, when the remote is in a carrying case and the P Power button is accidentally pushed.

4

49

433

Fine-tuning the Projector You can use the Menu button on the projector or remote control to access on-screen menus to adjust the image, sound, and other features. This chapter covers the following information:

Using the menu system

Adjusting image colors and clarity

Adjusting the input signal

Customizing projector features

Selecting projector setup options

Viewing lamp usage and other information

Using the projectors security features

Restoring the default settings

50 Fine-tuning the Projector

Using the Projectors Menu System The projector menus let you adjust and customize the projector features:

The Image menu lets you modify the colors of the projected image and fine-tune brightness, contrast, and sharpness. See page 52.

The Signal menu lets you make adjustments to the input signal. You can select your input source, change the image position and aspect ratio, and adjust tracking and sync for computer images. See page 54.

The Settings menu lets you customize the way you use the projector. It allows you to adjust the volume and keystone correction, set lamp brightness to high or low, control use of the remote control receivers, project a test pattern for adjustments, and disable buttons on the projector while you are projecting. See page 56.

The Extended menu lets you customize the way you set up the projector. Among the options, you can select the menu language, set rear or ceiling projection, turn closed captions on or off, and record a custom image or logo to be displayed as the startup screen or whenever you press the A/V Mute button on the remote control. See page 58 and page 62.

The Network menu lets you select your network settings and optional passwords for monitoring the projector over a network or over the web. See page 60.

The Info menu provides information about lamp status and computer or video settings. See page 61.

The Reset menu lets you restore the projectors factory default settings. See page 69.

Fine-tuning the Projector 51

Changing Menu Settings

Use the buttons on the remote control or on the projector to access the menus and change settings. Follow these steps:

1. Press the Menu button on the remote control or projector to display the menu screen:

The menus are listed on the left, and the options available for the highlighted menu are shown on the right.

2. Use the up and down arrow buttons on the projector or remote control to scroll through the menu list. When youve highlighted the desired menu, press the Enter button on the projector or the remote control to select it.

The highlight moves to the first option for that menu.

3. Use the up and down arrow buttons on the projector or remote control to scroll through the list of options. (The options available depend on which source is selected.)

4. After highlighting the option you want to adjust, use the left or right arrow buttons on the projector or the remote control to change the setting. In some cases, you may have to press the Enter button to see a sub-screen for changing the setting.

Menus

Menu options

52 Fine-tuning the Projector

Press the left or right arrow buttons on the projector or the remote control to adjust a slider bar.

To select from two or more settings, use the up or down arrow buttons on the projector or the remote control to highlight the desired setting, then press Enter.

5. Press the Esc button to return to the previous menu or to close the menu system if you are at the main menu. Your changes are saved automatically.

6. Press the Menu button to exit the menu system.

Adjusting Colors and Clarity The Image menu lets you make adjustments to the colors of the projected image and fine-tune brightness, contrast, and sharpness. The options available depend on which image source is selected:

Computer (analog-RGB) and RGB video

Component, composite, and S-Video

Fine-tuning the Projector 53

Follow these steps to adjust the appearance of your image:

1. Press the Menu button. You see the main menu.

2. Press Enter to select the Image menu.

3. Use the up and down arrow buttons and press Enter to set the following options:

Color Mode Corrects the vividness of image color. You can select from the following settings, and save a different one for each computer and/or video source:

Photo: For projecting still images with vivid color in a bright room (Computer input only).

Sports: For watching TV in a bright room (component, S-Video, or composite video input only).

Presentation: For color presentations in a bright room.

Text: For black and white presentations in a bright room.

Theatre: For optimizing movie images with natural color in a dark room (the default for video or S-Video display).

Game: Brightest mode, for playing video games in a bright room.

sRGB: For standard sRGB computer displays (the default when projecting from a computer with analog video).

Blackboard: Fixed color mode for projecting against a green blackboard.

Brightness Lightens or darkens the overall image.

Contrast Adjusts the difference between light and dark areas.

Color Saturation (component, composite, and S-Video) Adjusts the depth or intensity of the image colors.

note You can also select High or Low brightness mode in the Settings menu. See page 57.

54 Fine-tuning the Projector

Tint (component, composite, and S-Video) Adjusts the balance of green to magenta in the image.

Sharpness Sharpens or softens the image.

Color Adjustment Adjusts the temperature and intensity of red, green, and blue.

4. When the image is set correctly, press Esc or Menu. Your settings are automatically saved.

Adjusting the Input Signal Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to manually select it. You can also change the position of the projected image, correct tracking and sync, and change the aspect ratio to widescreen format.

1. Press the Menu button. You see the Image menu.

2. Select the Signal menu. You see one of the following screens:

Computer (analog-RGB) and RGB video Component video

Composite video and S-Video

Fine-tuning the Projector 55

3. Press Enter. Then use the up and down arrow buttons and the Enter button to set the following options:

Auto Setup (computer images) Leave this setting On to automatically optimize the computer image. Turn it off if you want to save adjustments you have made to the video settings.

Tracking (computer images) Removes unwanted vertical lines from a computer image by matching the projectors internal clock to various computer signals. See page 86 for more information.

Sync (computer images) Corrects fuzziness or screen flicker by synchronizing the projector with the tracking signal sent from the computer. See page 86 for more information.

Position (computer images) Use the arrow buttons to move the image on the screen left, right, up, or down.

Progressive Leave this setting On when viewing S-Video or composite video so that interlaced-to-progressive conversion is carried out (best for fast-moving pictures). If you notice flickering while viewing still images, switch this setting to Off.

Computer Input (1 or 2) Selects the signal from equipment connected to the Computer1 or Computer2 ports. If your image colors look wrong, try changing this setting from Auto to one of the following: RGB for computer or RGB video sources, or Component Video for component video sources.

note If you have repositioned the image but then change your mind, you can press the Enter/Auto button on the remote control to restore the default settings.

56 Fine-tuning the Projector

Video Signal (composite and S-Video) Leave this setting at Auto unless you are using a 60-Hz PAL system (select PAL60).

Aspect Sets the images aspect ratio (ratio of width to height). Select 4:3 for Normal for computer content, 4:3 for letterbox video content, 16:9 for widescreen content, or 16:9 (Up) or 16:9 (Down) for video content with subtitles or supertitles.

4. When youre finished, press Esc or Menu.

Customizing Projector Features The Settings menu lets you customize the way you use the projector, from adjusting volume and lamp brightness to applying security controls.

1. Press the Menu button.

2. Select the Settings menu.

Fine-tuning the Projector 57

3. Press Enter. Then use the up and down arrow buttons and the Enter button to set the following options:

Keystone Adjusts a distorted image from a trapezoid shape to rectangular.

Auto Keystone Automatically adjusts a distorted image from a trapezoid shape to rectangular when the projectors foot is extended or retracted. (Not available when youre projecting from the ceiling or using rear projection.) Select On or Off.

Operation Lock Disables all projector buttons (Full Lock) or all the buttons except the P Power button (Operation Lock). You can still operate the projector from the remote control. Changes to this setting take effect after you restart the projector. (After you turn off the projector, wait for the PPower light to turn a steady orange before turning it on again.)

Brightness Control Select Low lamp brightness when the projection is too bright for the room. The Low setting also reduces electricity consumption and fan noise. Select High to project the maximum brightness. (Also check the Brightness setting in the Image menu; see page 53.)

Volume Adjusts the volume.

Remote Receiver Deactivates the projectors front and/or back sensors that detect signals from the remote control. This may be necessary to prevent interference from bright fluorescent lights.

Test Pattern Displays a test pattern to assist you in focusing and zooming the image, and correcting the image shape. (To cancel the displayed test pattern, press Esc.)

4. When youre finished, press Esc or Menu.

note To cancel the Operation Lock function from the projector, press the Enter button for about seven seconds.

58 Fine-tuning the Projector

Selecting Projector Setup Options Use the Extended menu to customize the way you set up the projector. You can configure the projector for rear and/or ceiling projection, change the language for the menus and messages, set the screen background color, capture and store a custom image or logo for the startup screen.

1. Press the Menu button.

2. Select the Extended menu.

3. Press Enter. Then use the up and down arrow buttons and the Enter button to set the following options:

Display

Messages: Lets you turn screen messages on or off.

Display Background: Sets the screen background to Black, Blue, or Logo when no image signal is available.

Startup Screen: Enables or disables display of the startup screen when the projector is turned on.

A/V Mute: Sets the screen background to Black, Blue, or Logo when the A/V Mute button is pressed.

Closed Caption: Enables or disables closed captions. Select CC1, CC2, or OFF. The captions are not visible when the menu is displayed or when you use EMP Monitor to access the projector through your network.

Fine-tuning the Projector 59

Users Logo Turn on to display the image or logo you have captured whenever the projector is turned on. See page 64 for more information.

Projection

Front: Projector is in front of the screen.

Front/Ceiling: Projector is in front of the screen, mounted upside-down from the ceiling.

Rear: Projector is behind the screen.

Rear/Ceiling: Projector is behind the screen, mounted upside-down from the ceiling.

To change from Front to Front/Ceiling or Rear to Rear/Ceiling, press and hold the A/V Mute button on the remote control for five seconds.

Operation

Direct Power On: When this feature is enabled, projection starts as soon as you plug in the power cord. You dont have to press the P Power button.

Sleep Mode: When enabled, the projector turns off the lamp if it has not received any input signals for a period of time (as defined in the Sleep Mode Time setting).

Sleep Mode Time: When Sleep Mode is on, you can set the period of time before the projector turns off automatically, from 1 to 30 minutes.

Lens Cover Timer: This feature is enabled by default to turn the power off automatically when the A/V Mute slide is closed for more than 30 minutes.

High Altitude Mode: When using the projector at an altitude above 4,921 feet (1,500 meters), turn this setting on to ensure that the internal temperature of the projector is regulated properly. Turn this setting off for lower elevations.

note Logo settings cannot be changed if the Users Logo Protect feature has been turned on. See page 65.

note When Direct Power On is turned on, press the P Power button to turn the projector off, wait until the P Power light turns a steady orange, then unplug the power cord.

60 Fine-tuning the Projector

Standby Mode Select Network On to allow the projector to be monitored over a network when the projector is in standby mode (the P Power light is orange).

Language Select the language to be used for the projector menus.

4. When youre finished, press Esc or Menu.

Selecting Network Settings For information connecting the projector to a network and monitoring the projector over a network, see Monitoring the Projector Over a Network on page 91.

Fine-tuning the Projector 61

Viewing Lamp Usage and Other Information Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used.

1. Press the Menu button.

2. Select the Info menu. You see one of the following menus:

Lamp Hours Displays the number of hours the lamp has been used. The life span of the lamp ranges from about 3000 hours in High brightness mode to about 4000 hours in Low brightness mode. If the number shown is close to 3000 or the information is displayed in red, make sure you have a spare lamp handy.

Source Displays the input source currently being projected.

Input Signal (computer, RGB video, and component video) Displays the input signal setting.

Resolution (computer, RGB video, and component video) Displays the input resolution.

Video Signal (composite and S-Video) Displays the video signal format.

note You can make changes to many of the signal settings on the Signal menu. See page 54 for details.

Computer (analog RGB, digital RGB, RGB Video/Component video)

Video (Composite video, S-Video)

note The lamp usage timer doesnt register until youve used the lamp for at least 10 hours.

62 Fine-tuning the Projector

Refresh Rate (computer, RGB video, and component video) Displays the refresh rate.

Sync Info (computer, RGB video, and component video) Provides information that may be needed by the service technician.

Status Displays informations about projector problems. This information may be needed if service is required.

3. When youre finished, press Esc or Menu.

Using the Projectors Security Features To prevent unauthorized use of the projector, you can do the following:

Create an identifying user logo that is displayed at startup and/or when the A/V Mute button is pressed.

Assign a password to prevent the projector from being turned on, prevent your startup screen from being changed, and lock network settings.

Disable the projectors buttons; this is useful, for example, if youre projecting in a classroom and you want to ensure that no one touches the projectors buttons while youre using the remote control.

Install an anti-theft lock.

If you create a users logo for the projector, you can lock the logo on so it is displayed as the startup screen and/or AV/Mute screen. Unauthorized users cannot turn it off or change it. This feature is intended to discourage theft and provides a way to identify the projector should it be stolen.

Fine-tuning the Projector 63

If you assign the projector a password, a screen appears requesting the password whenever the projector is turned on. If you enter the password incorrectly three times in succession, the projectors operation is locked and youll need to disconnect the power cord, then reconnect it to redisplay the password screen. If an incorrect password is entered 30 times in a row, the projector is locked and youll need to contact Epson to unlock it. See Where To Get Help on page 89.

If someone else will be using the projector for awhile but you want to make sure that person returns it by a certain time, you can temporarily disable the password for a set period. When that time has elapsed, the password is reactivated and must be entered before the projector can be used.

When you enable the Operation Lock feature, all of the projectors buttons (Full Lock) or all of the buttons except the P Power button (Operation Lock) are disabled.

note If you should happen to enable the password before you set one and you see the prompt to enter the password, enter the default password 0000 to proceed.

64 Fine-tuning the Projector

Creating Your Own Screen Logo

You can transfer any image on your computer to the projector, and then use it as the startup screen and/or the screen that is displayed when you press the A/V Mute button. The image can be a company logo, slogan, photograph, or any other image you want to use. The projector considers this image the Users Logo.

Follow these steps to capture the image and transfer it to the projector:

1. Display the image you want to use on the projector. You can use an image from a computer or video source, such as a DVD player.

2. Press the Menu button and select the Extended menu.

3. Use the down arrow button and press Enter to select Users Logo.

4. When you see a message asking if you want to use the present image as a users logo, select Yes and press Enter. A selection box displays over the image.

5. Use the arrow buttons on the projector or remote control to select the area of the image you want to use. Once you have selected the area, press Enter.

6. When you see the message Choose this image as the Users Logo?, choose Yes and press Enter. If you want to change the area selected, select No, press Enter and repeat steps 5 and 6.

note If the Users Logo Protect function is ON, you see a message that the logo cannot be recorded. Youll need to disable the Users Logo Protect function before you can create or change the Users Logo. See page 66.

Fine-tuning the Projector 65

7. When you see this screen, select a zoom rate (display size), and then press Enter.

8. When you see the message Save image as users logo?, select Yes and press Enter. Saving the logo takes a few moments. Do not use the projector or other sources (computer, video, etc.) while the logo is being saved. When you see the message Completed, press Esc.

9. To display the logo as the background screen when you press the A/V Mute button or when no image signal is available, select the Extended menu and press Enter. Then select Display, Display Background, and Logo and press Enter. Select A/V Mute and Logo and press Enter.

10. When youre finished, press Menu to exit the menus.

Setting a Password

1. Press the Freeze button on the remote control for about five seconds until you see the Password Protect menu:

2. Select Password and press Enter.

note The default setting for the Startup Screen option menu is On. If the Startup Screen is set to Off, the logo will not display at startup.

If the Users Logo Protect function has been set to On, the Display Background setting cannot be changed. You need to turn the protect function off first. See page 66 for details.

Once youve saved a users logo, you cannot reset the logo setting to its factory default (no logo).

note If a password has already been set, you see the Password Protect Release screen. See Starting the Projector with a Password on page 67.

66 Fine-tuning the Projector

3. When you see the message Change the password?, select Yes and press Enter.

4. Enter a 4-digit number using the numeric buttons on the remote control, as shown.

The password will be displayed as ****. After you enter the last digit, a confirmation screen appears. Enter the password again. You see the message Password accepted.

5. After you finish setting the password, press the Esc button to return to the Password Protect menu.

Make a note of the password and keep it in a safe place in case you forget it.

Turning On the Password and Users Logo

1. Press the Freeze button on the remote control for about five seconds until you see the Password Protect menu.

2. To enable the password, select Power On Protect and press Enter. Select On then press Esc.

3. To enable your screen logo, select Users Logo Protect and press Enter. Select On then press Esc.

When this feature is on the logo appears whenever the projector is turned on (if the Startup Screen is enabled in the Extended menu; see page 58) and as the A/V Mute screen (if you selected the Logo as the Display Background in the Extended menu). None of the Users Logo features can be changed when the Users Logo Protect function is enabled.

4. To lock the network settings in the menu system, select Network Protect and press Enter. Select On and press Enter.

5. Press Menu to close the Password Protect menu.

If you lose the remote control, you will not be able to enter the password, so keep the remote control in a safe place at all times.

You can attach the password protect sticker to the projector as an additional theft deterrent.

Numeric buttons

Fine-tuning the Projector 67

Starting the Projector with a Password

When the password function is enabled, you see this screen when you turn on the projector:

Use the numeric buttons on the remote control to enter the password. Once you have entered the password correctly, the password screen closes, and projection begins.

If the password is not correct, you see the message Wrong password. Please try again. If you enter an incorrect password three times in succession, you see the message The projectors operation will be locked. Request code xxxxx and the projector switches to standby mode for approximately 5 minutes. Write down the request code. Then disconnect the projectors power cord from the electrical outlet, reconnect it, and turn the projector back on.

When you see the Password Protect Release screen again, you can try to enter the correct password.

If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson for service.

If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for assistance. See Where To Get Help on page 89.

68 Fine-tuning the Projector

Disabling the Projectors Buttons

You can use the Operation Lock function to disable all the projectors buttons, or all the buttons except for the P Power button.

1. Press the Menu button.

2. Select the Settings menu and press Enter.

3. Use the up and down arrow buttons to select Operation Lock and press the Enter button.

4. Select Full Lock to disable all the buttons, or Operation Lock to disable all except the P Power button. Then press Enter.

5. Select Yes and press Enter to confirm the setting.

6. Press the Menu button.

Installing Security Locks

You can install two different types of security locks on the projector:

You can use the security slot on the base of the projector to install a Kensington Microsaver Security System. See page 14.

You can use a wire lock to secure the projector to a room fixture or heavy furniture, as shown below:

note To cancel Operation Lock, press the projectors Enter button for 7 seconds.

Fine-tuning the Projector 69

Restoring the Default Settings The Reset menu lets you return most projector menu settings to their default values. It also lets you reset the lamp hours to their initial default value; see page 77 for instructions on resetting the lamp timer.

To reset most projector menu settings, select Reset All and press the Enter button to display the confirmation screen. Select Yes to reset all the default settings or No to cancel.

note The Computer Input (1 and 2), Users Logo, Network menu settings, Lamp Hours, and Language settings do not return to their defaults when you select Reset All. To reset the computer inputs, use the Reset option on the Signal menu; see page 54 for details. To reset the network settings, use the Reset option on the Network menu; see page 60 for details. To reset the Language settings, use the Reset option on the Extended menu; see page 58 for details.

70 Fine-tuning the Projector

5

71

5

Maintenance and Transportation Your projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. Any dirt or smears on the lens may show up on your projected image.

You may need to clean the air filter and air vents. A clogged air filter or air vent can block ventilation needed to cool the projector and cause overheating.

The only parts you should replace are the lamp and air filter. If any other part needs replacing, contact your dealer or a qualified servicer.

This chapter covers the following:

Cleaning the lens

Cleaning the projector case

Cleaning and replacing the air filter

Replacing the lamp

Resetting the lamp timer

Transporting the projector

warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this Users Guide. Refer all other servicing to qualified service personnel.

72 Maintenance and Transportation

Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface.

Use a canister of compressed air to remove dust.

To remove dirt or smears on the lens, use lens-cleaning paper. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface.

Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord.

To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.

To remove stubborn dirt or stains, moisten a soft cloth with water and a mild detergent. Then wipe the case.

Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case.

Cleaning and Replacing the Air Filter Your projector includes an air filter to ensure the best performance. If dust collects on the air filter or vent on the bottom of the projector, clean them as described below. Dust clogs prevent proper ventilation and can cause overheating and damage the projector.

When the filter and vent are clogged, the projector displays the message The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter.

caution Do not use glass cleaner to clean the lens.

Maintenance and Transportation 73

To clean the air filter and air vent, follow these steps:

1. Turn off the projector, allow it to cool down, and unplug the power cord.

2. To clean the filter and vent, Epson recommends using a small vacuum cleaner designed for computers and other office equipment. If you dont have one, gently clean them using a very soft brush (such as an artists paintbrush).

You can remove the air filter to clean both sides.

If the dirt is difficult to remove or if the filter is torn, replace it. Contact your dealer or call Epson at (800) 463-7766 to obtain a new one (part number V13H134A13).

3. If you need to clean or replace the filter, slide it off, as shown.

Air filter

Vent

74 Maintenance and Transportation

4. Align the new filter and slide it in until it clicks into place.

Replacing the Lamp The projection lamp typically lasts for about 3000 hours of use (in high brightness mode) or 4000 hours (in low brightness mode). It is time to replace the lamp when:

The projected image gets darker or starts to deteriorate.

The lamp light is flashing orange.

The message Replace the Lamp appears on the screen when the lamp comes on. To maintain projector brightness and image quality, replace the lamp as soon as possible.

Contact your dealer or call Epson at (800) 463-7766 for a replacement lamp. Request part number V13H010L42.

Follow these steps to replace the lamp:

1. Press the P Power button twice to turn off the projector. When you hear the projector beep twice, unplug the power cord.

2. If the projector has been on, allow it to cool down for at least an hour (or until the lamp is cool).

note Air filters contain polycarbonate, ABS resin, and polyurethane foam. Dispose of used air filters according to local regulations.

note You can check to see how many hours the lamp has been used. See page 61.

Turn off this product when not in use to prolong the life of the projector.

warning Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury.

Maintenance and Transportation 75

3. Use the screwdriver included with the replacement lamp or a #2 Phillips-head screwdriver to loosen the screw holding the lamp cover (the lamp cover is located on top of the projector).

4. Slide the cover out, then lift it off.

5. Use the screwdriver to loosen the two screws holding the lamp in place. (You cant remove the screws.)

6. Hold the lamp as shown and pull it straight out. note The lamp(s) in this

product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

Dont remove these screws

76 Maintenance and Transportation

7. Gently insert the new lamp along the guide rail. If it doesnt fit easily, make sure its facing the correct way. Push the lamp down firmly where the label PUSH appears.

8. Once the lamp is fully inserted, tighten its screws.

9. Lower the lamp cover into place. (The opening should be almost covered, and the top of the cover should be flush with the top of the projector.) Then slide the cover closed and tighten the screw.

10. Reset the lamp timer as described in the next section.

caution Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure.

note Be sure to seat the lamp fully and secure the lamp cover. If the lamp is not properly installed or the cover is loose, the lamp will not turn on.

Maintenance and Transportation 77

Resetting the Lamp Timer You must reset the lamp timer after replacing the lamp to clear the Replace the Lamp warning message. Follow these steps:

1. Connect the power cable and turn on the projector.

2. Press the Menu button on the remote control or projector and select the Reset menu. Then press Enter.

3. Select Reset Lamp Hours and press Enter. You see a confirmation screen.

4. Select Yes and press Enter.

5. Press Esc to return to the main menu or the Menu button to exit the menu system.

note Do not reset the lamp timer if you have not replaced the lamp. If you do, the Lamp Hours will not accurately reflect the number of hours that the lamp has been used.

78 Maintenance and Transportation

Transporting the Projector The projector contains many glass and precision parts. If you need to transport it, please follow these packing guidelines to prevent damage to the projector:

When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.

When transporting the projector as freight or checked luggage, first put it in a carrying case, then pack it in a firm box, using cushioning around the case.

When you are hand-carrying the projector, be sure to use a carrying case.

note Epson shall not be liable for any damage incurred during transportation.

6

79

6

Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you cant solve yourself. This chapter explains the following:

Using the projectors on-screen help system

What to do when the projectors status lights flash

Solving problems with the image or sound

Solving password problems

Solving problems with the remote control

Solving problems monitoring the projector over a network

Contacting technical support

80 Solving Problems

Using On-Screen Help If the image doesnt look right or your audio isnt working, you can get help by pressing the ? Help button on the projector or remote control.

1. Press the ? Help button on the remote control or projector. You see the Help menu.

2. Use the up and down arrow buttons on the projector or remote control to highlight the problem you want to solve. Then press the Enter button to view the solution(s).

3. Press Esc to view another topic or press ? Help to exit.

If none of the suggestions solves your problem, see additional solutions to problems in the following sections.

What To Do When the Lights Flash The lights on top of the projector indicate the projectors status and let you know when a problem occurs.

If the projector is not working correctly, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this does not solve the problem, check the status lights on top of the projector and try the solutions recommended in the following table.

Lamp light

Power light

Temperature light

Solving Problems 81

Power

light

Lamp

light

Temperature

light Description

Green Off Off The projector is operating normally.

Flashing green

Off Off The projector is warming up. Wait for the image to appear.

Orange Off Off The projector is in standby or sleep mode. You can unplug it or press the P Power button to turn it on.

Flashing orange

Off Off The projector is shutting down. Wait for the light to stop flashing and remain orange before unplugging it.

Red Off Flashing orange

The projector is too hot. Make sure the temperature surrounding the projector does not exceed 95 F (35 C) and there is plenty of space around and under the projector for ventilation. Clean the air filter and air vents, if necessary. See page 72 for instructions.

Red Off Red The projector has overheated and turned itself off. Let it cool for about five minutes, then turn it back on. Make sure there is plenty of space around and under the projector for ventilation. If you are using the projector at an altitude above 4921 ft (1500 m), turn on High Altitude Mode as the Operation setting in the Extended menu; see page 58. Also clean the air filter and air vents; see page 72. If it continues to overheat, you may need to replace the air filter.

Red Flashing red

Off The lamp is burned out, broken, or not installed correctly; or the lamp cover is open. Close the cover or replace or reseat the lamp, if necessary, as described on page 74. Also clean the air filter and air vents; see page 72. If these suggestions dont work, contact Epson.

Orange Flashing orange

Off Replace the lamp with a new one as soon as possible; see page 74 for instructions. If you continue to use the lamp, there is a risk it may break.

Red Off Flashing red There is a problem with the fan or a sensor. Clean the air filter and air vents; see page 72. If this does not solve the problem, turn the projector off and unplug it. Contact Epson for help; see page 89.

Red Red Red There is an internal error in the projector. Turn the projector off and unplug it. Contact Epson for help; see page 89.

82 Solving Problems

Solving Problems with the Image or Sound

No image appears on the screen.

Check that the P Power light is green, not flashing, and the A/V Mute slide is open. Also press the A/V Mute button on the remote control to see if the picture was turned off temporarily.

If the projector doesnt turn on, the Operation Lock may be enabled. Press and hold the Enter button on the projector for 7 seconds to release the lock.

The projector may be in standby or sleep mode. If the projector has not received any signal for 30 minutes, it turns off the lamp to conserve the lamp life and save energy. If the P Power light is orange, press the P Power button to turn on the projector.

The attached computer may also be in sleep mode or displaying a black screen saver. Try pressing a key on the computer.

If the power was switched off and then on again, wait until the P Power light stops flashing and remains orange. Then press the P Power button again.

Check the Video Signal, Computer1 Input, or Computer2 Input setting in the Signal menu to make sure it is correct for the selected source. See page 54 for more information.

Messages may have been turned off in the Display setting of the Extended menu. See page 58 for details.

Adjust the Brightness setting on the Image menu (see page 53) or select High for the Brightness Control setting in the Settings menu (see page 57).

With Direct Power On enabled in the Operation setting of the Extended menu, if you unplug the projector and then plug it right back in, you must press the P Power button to turn on the projector. See page 58 for details.

Make sure at least one of the projectors remote receivers are turned on in the Settings menu. See page 56 for details.

Solving Problems 83

Nothing appears on the external monitor.

Make sure the VGA computer cable is connected to your computers video port and the projectors Computer1 port.

Make sure the cable from your monitor is connected to the projectors Monitor Out port.

You see a blue screen with the message No Signal displayed.

Make sure the cables are connected correctly, as described in Chapter 1.

Make sure the power to your computer or video source is turned on.

If youve connected a computer and one or more video sources, you may need to press the Source Search button on the projector or the remote control to select the correct source. Allow a few seconds for the projector to sync up after pressing the button.

If youve connected a laptop computer, make sure its set to display on an external monitor. See page 36.

The message Not Supported is displayed.

Make sure your computers resolution doesnt exceed UXGA and the frequency is supported by the projector. See page 107. If necessary, change your computers resolution setting as described on page 84.

Make sure the correct Video Signal is selected in the Signal menu. See page 56. It should normally be set to Auto.

The buttons on the projector dont work.

The Operation Lock may be enabled. Press and hold the Enter button on the projector for 7 seconds to release the lock.

84 Solving Problems

Only part of the computer image is displayed.

If youre projecting from a computer or RGB video device, press the Enter/Auto button on the remote control. If this doesnt work, you may need to adjust the Position setting in the Signal menu. See page 55 for more information.

If youve enlarged part of the image using the E-Zoom button on the remote control, press the Esc button to cancel zooming and return to full display.

Try pressing the Aspect button on the remote control to select a different aspect ratio (4:3, 16:9, or another available setting).

Make sure your computers resolution setting is correct and dual display is not activated. Ideally, it should be 1024 768 to match the projectors native resolution. If this option isnt available, select another compatible video format. See page 107.

Windows: Right-click the desktop, select Properties, click the Settings tab, and select a different resolution.

Macintosh OS X: On the Apple menu, choose System Preferences, then click Displayor Displays. Select a different resolution.

You also may need to modify existing presentation files if you created them for a different resolution. See your software documentation for specific information.

The image isnt rectangular, but trapezoid-shaped.

Make sure the projector isnt placed off to one side of the screen, at an angle, or the image wont be rectangular. Place it directly in front of the center of the screen, facing the screen squarely.

If youve tilted the projector upward, the image will be broader at the top. Turn on Auto Keystone as described on page 56 or hold down the or buttons on top of the projector until the image is rectangular.

Solving Problems 85

The image contains static or noise.

If youre using a computer cable longer than 6 feet (2 meters), or an extension cable, the image quality may be reduced.

Keep your computer and video cables separated from the power cord as much as possible to prevent interference.

The video signal may be split between the computer and the projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your laptop computer and the projector, turn off the laptops LCD display.

If youre projecting from a composite or S-Video source, check the Video Signal setting in the Signal menu. In most cases, leave it set at Auto. If youre using a 60-Hz PAL video source, change this setting to PAL60. See page 56 for details.

Make sure the cables are securely connected at both ends.

Select the correct resolution; see Compatible Video Formats on page 106.

If youre projecting from a computer, press the Enter/Auto button on the remote control or the Enter button on the projector to adjust tracking and sync automatically. If that doesnt work, try adjusting the Sync and Tracking settings in the Signal menu. See page 55.

The image is blurry.

Adjust the focus using the focus ring. See page 38.

Try cleaning the lens as described on page 72.

Make sure the lens is not fogged by condensation. You may need to wait before using the projector after moving it from a cold environment.

Make sure the projection distance is within the range described on page 16.

Adjust the Sharpness setting on the Image menu (see page 54). You should be able to see the effect on the screen immediately.

86 Solving Problems

You see vertical stripes or the image still looks blurry after trying the solutions in the previous section.

If youre projecting from a computer and displaying an image that contains a lot of fine detail, you may notice one or more vertical stripes or bands, or some of the characters may look heavy or blurred. Press the Enter/Auto button on the remote control to automatically reset the projectors tracking and sync settings.

If necessary, you can manually adjust the Tracking and Sync settings on the Signal menu as described on page 55.

To help you adjust these settings, fill the screen with a detailed image, such as a desktop background pattern or black text on a white background. Adjust the Tracking setting to eliminate vertical stripes; adjust the Sync setting to increase the sharpness.

The colors of the image are not right.

Try selecting a different Color Mode. See page 53 for instructions.

If youre displaying video, adjust the Color Saturation and Tint settings on the Image menu. See page 53 for instructions.

Adjust the Brightness, Contrast, and Color Adjustment settings on the Image menu. See page 53.

Make sure the input signal setting on the Signal menu matches the signal from the connected device. See page 54 for details.

If the image is too purple and youve connected a computer or RGB video device to the Computer1 or Computer2 port, select Computer as the input source. If youve connected a component video device to one of these ports, select Component Video.

If youre projecting from a composite video or S-Video source, select the correct Video Signal is selected on the Signal menu.

Check your computer display settings to correct the color balance.

If the image seems dark, the lamp may be nearing time for replacement. Check the lamp hours as described on page 61 and replace it, if necessary, as described on page 74.

note Because of the different technologies used, your projected image may not exactly match the colors on your laptop or computer monitor.

Solving Problems 87

There is no sound.

Press the button on the projector or the Vol+ button on the remote control to turn up the volume.

If youve turned off the picture and sound, press the A/V Mute button on the remote control to turn them on again.

If youre using a DVD player or other video source, or external speakers, make sure their volume is not turned all the way down or muted. Also, make sure the cables are connected correctly, as described in Chapter 1.

Make sure the audio cable is connected to the correct audio port. See page 22 or page 29.

If your presentation includes computer audio, make sure the volume control on your computer is not turned all the way down or muted. Make sure the audio cable is securely connected to both the projector and your computer. See page 22.

The wrong source may be selected. Press the Source Search button on the projector or the remote control.

Solving Password Problems

You have forgotten the password.

Write down the request code that appears in the Password Protect Release screen and contact Epson. See page 89.

If you turned on the password protect feature before setting the password and no password was set before, try using the default password: 0000.

The remote control is not available.

You must have the remote control to enter the password. You can purchase a replacement remote control from Epson. See page 90.

88 Solving Problems

Solving Problems with the Remote Control

The projector doesnt respond to remote control commands.

Make sure you are within 20 feet of the projector, and within range of the projectors front or back sensor (approximately 30 to the left or right and 15 above or below).

If a button on the remote control is held for more than 30 seconds, the remote enter sleep mode. Press another button for normal operation.

The remote control batteries may not be installed correctly or may be low on power. Replace the batteries as described on page 48.

Dim the room lights and turn off any fluorescent lights. Make sure the projector is not in direct sunlight. Strong lighting, especially fluorescent lights, may affect the projectors infrared receivers. If you still have trouble using the remote control, disable one of the remote receivers using the Settings menu to block interference from bright light. See page 56 for details.

Turn off any nearby equipment that emits infrared energy, such as a radiant room heater.

You have lost the remote control.

You need the remote control to access many projector features. If you have lost it, you can order another from Epson. See page 90 for details.

Solving Problems 89

Solving Network Problems

You dont see your projector in the EMP Monitor window.

Make sure that youve connected the projector to the network and configured it correctly; see page 93. Also, make sure youve registered the projector with EMP Monitor; see page 97.

Make sure that Standby Mode in the projectors Extended menu is set to Network On; see page 58.

If the computer you are using is running Windows XP or 2000, you must be logged in as the Administrator.

Try restarting your computer.

You dont receive an e-mail over the network when a projector problem occurs.

Make sure that Standby Mode in the projectors Extended menu is set to Network On; see page 58.

Make sure that youve connected the projector to the network and configured it correctly; see page 93.

Make sure you set up projector e-mail alerts correctly in the Network menu (see page 95) or in EMP Monitor (see page 100).

Where To Get Help Epson provides these technical support services:

Internet Support

Visit Epsons support website for solutions to common problems with the PowerLite 822+ or PowerLite 83+. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Visit Presenters Online to access tips, templates, and training for developing successful presentations.

90 Solving Problems

Speak to a Support Representative

To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card. This is the fastest way of speaking to a live representative, and its free. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period.

You may also speak with a projector support specialist by dialing one of these numbers:

U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday through Friday

Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday

Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Before you call, please have the following information ready:

Product name (PowerLite 822+ or PowerLite 83+)

Product serial number (located on the bottom of the projector)

Proof of purchase (such as a store receipt) and date of purchase

Computer or video configuration

Description of the problem

Purchase Supplies and Accessories

You can purchase screens, carrying cases, or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).

note To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer referral in Canada).

7

91

7

Monitoring the Projector Over a Network The software included with your projector lets you monitor and control your projector over a network.

Use EMP Monitor (available for Windows only) to see your projectors status, switch image sources, and control basic settings.

Use the mail notification function to receive e-mail alerts about possible problems.

To use the software to manage your projectors, first install EMP Monitor. Then connect and configure the projector you want to monitor as described here.

This chapter covers the following information:

Installing the network software

Connecting your projector to a network

Selecting network settings

Monitoring and controlling your projector with EMP Monitor

Using a browser to monitor the projector

92 Monitoring the Projector Over a Network

Installing the Network Software The network software CD-ROM includes the software you need to monitor the projector from a remote location. The Epson Projector Software CD-ROM includes EMP Monitor for monitoring the projector from a remote location.

Windows System Requirements

Before you install the software, make sure your computer meets these requirements:

Microsoft Windows 98SE, Me, 2000 (SP4), or Windows XP

IBM compatible PC with at least a Pentium III 1.2 GHz processor

At least 256MB of RAM (512 recommended)

At least 128MB of free hard disk space

XGA (1024 768) or better display adapter and monitor, 16-bit color or higher

Installing the Software on a Windows System

1. Insert the network software CD-ROM in your computers CD-ROM or DVD drive.

2. Click Custom, then make sure EMP Monitor is selected.

3. Click Install, then follow the on-screen instructions to install your projector software.

4. When installation is complete, click Exit.

Monitoring the Projector Over a Network 93

Connecting to the Network Follow these steps to connect the projector to your network and configure it with an IP address.

1. Connect the projector to your network using a commercially available 100BaseTX or 10BaseT network cable. Connect the cable to the LAN port on the projector.

2. Press the projectors P Power button to turn it on.

94 Monitoring the Projector Over a Network

Selecting Network Settings Follow the instructions in this section to set up the projectors network settings in the menu system.

1. Press the Menu button.

2. Select the Network menu.

3. Press Enter. Then use the up and down arrow buttons and the Enter button to set the following options:

Wired LAN If your network assigns addresses automatically, turn on the DHCP setting.

If your network does not assign addresses automatically, turn off DHCP and enter the projectors IP Address, Subnet Mask, and Gateway Address as needed.

To enter numbers, use the numeric buttons on the remote control.

PJLink Password Lets you enter a password for using the PJLink protocol to control the projector.

Web Control Password Lets you enter a password for accessing the projector over the web from a computer running the EMP Monitor software.

Monitoring the Projector Over a Network 95

SNMP If youre a network administrator, you can use the SNMP option to enter a trap IP address. This lets you receive trap alerts for the projector on a computer running the SNMP Manager software.

Mail When enabled, the projector sends you an e-mail alert if it has any problems. For instructions on setting up e-mail alerts, see the next section.

Projector Name Enter a name for identifying the projector over the network.

Using Projector E-mail Alerts

When this feature is enabled, the projector sends you an e-mail alert if it has any problems.

1. Press the Menu button, select the Network menu, and press Enter.

2. Select Mail and press Enter.

3. Select the following settings as necessary:

Mail Notification Select On to enable sending of an e-mail if there is a problem with the projector.

SMTP Server Enter the IP address for the SMTP server for the projector. You can enter a number from 0 to 255 in each field of the address.

Port Number Enter the SMTP servers port number. The default value is 25. You can enter a numeric value from 1 to 65535.

Destination Address 1/2/3 Choose one of the Destination Address fields, then enter the e-mail address where you want to receive a message when a problem occurs.

note You can also set e-mail alerts from EMP Monitor (see page 100).

note If a critical problem develops with a projector which causes it to suddenly stop working, it may not be possible for the projector to send a message.

If Standby Mode is set to Network On in the Extended menu, the projector can still be monitored even if the projector is in standby mode (when the power is off).

96 Monitoring the Projector Over a Network

4. When youre done, press Menu to exit the menu system.

When a problem occurs, an e-mail message is sent to the specified addresses with the subject line EPSON Projector and the following information:

Line 1: The name of the projector where the problem has occurred

Line 2: The IP address of the projector where the problem has occurred

Line 3: Details of the problem

Using EMP Monitor EMP Monitor lets you use a remote computer to manage your projectors. It lets you easily turn the projector on or off, switch image sources, and check its status.

Before using EMP Monitor, make sure youve installed the software (available for Windows only) as described on page 92. The computer youre using to monitor the projector should already be connected to your network.

Opening and Closing EMP Monitor

To start EMP Monitor, click Start > Programs or All Programs > EPSON Projector > EMP Monitor.

If youve added the program to the Startup programs folder, then it may already be open. If so, click the icon in the system tray on the lower-right corner of your screen to display the EMP Monitor window:

To close EMP Monitor, select Exit from the File menu or right-click the program icon shown above, then select Exit.

note If you want to monitor the projector while it is in standby mode, select Standby Mode in the Extended menu, then select Network On. See page 58.

Click here to start EMP Monitor

Monitoring the Projector Over a Network 97

Registering a Projector

Before you can monitor a projector, you have to register it. Follow these steps to automatically search for your projector.

1. Open EMP Monitor.

2. Select Edit > New > Projector (automatic search).

3. Click Search to locate projectors currently operating on the network.

4. Select the projector you want to add by clicking its name, then click the Edit button.

5. Enter a Display name, select a Parent group, if necessary, enter a Monitor Password, if necessary, and a Description for the projector.

6. Click the Register button.

7. Repeat steps 2 through 5 to register any additional projectors on the network.

8. When youre done adding the projector, click Cancel. You see a screen with a list of all registered projectors:

Monitoring Your Projector

The EMP Monitor screen lets you monitor your projector status and check if a problem has occurred.

For the most current status, click the Refresh button.

The following table describes the EMP Monitor status icons.

Group status icons

No warnings or problems in the projector group.

Warning or problem in a projector in the group.

Monitoring disabled. Right click the icon and select Monitoring Enabled to begin monitoring the group.

Data is currently being updated.

note If the projector is not automatically found, your projector may not be connected or configured correctly for the network. See page 93.

To delete a projector from the list, right-click the projector name, and click Delete.

note To monitor a projector when its in standby mode (plugged in but not turned on), you must select Network On as the Standby Mode setting in the projectors Extended menu (see page 58).

For detailed status information, right-click the projector and click Property.

98 Monitoring the Projector Over a Network

Type status icons

No warnings or problems.

Warning or problem.

Monitor Password error. No monitor password was entered when you registered the projector, or an incorrect password was entered.

Monitoring disabled. Right-click the icon and select Monitoring Enabled to monitor the projector.

Data is currently being updated.

Network error (projector is not connected to the network, the power cable is disconnected, or Network Off is selected as the Standby Mode setting in the Extended menu; see page 58).

Network error (Esc/VP.net communication error).

Power status icons

The projector is powered on; normal status.

The projector is powered off; normal status.

The projector is powered on; abnormal status.

The projector is powered off; abnormal status.

Temperature level status icons

The projectors internal temperature is normal (low).

The projectors internal temperature is normal (medium).

The projectors internal temperature is normal (high).

The projectors internal temperature is high (high-temperature warning).

The projectors internal temperature is too high (high-temperature error). The projector is turned off automatically.

Monitoring the Projector Over a Network 99

Error status icons

Lamp life warning. The lamp is nearing the end of its life.

High-temperature warning. The projector is getting too hot but continues to operate.

Replace air filter.

No air filter. The air filter is not installed or installed incorrectly.

Low air flow. The air filter needs to be cleaned or replaced.

Air flow sensor error. Contact Epson as described on page 89.

Lamp cover door open. Close the lamp cover door.

Lamp out. The lamp has reached the end of its life.

Lamp failure at power on. The lamp has reached its end of life or is installed incorrectly.

High internal temperature error. The projector is turned off automatically.

Internal (system) error. Contact Epson as described on page 89.

Fan error. Contact Epson as described on .

Sensor error. Contact Epson as described on page 89.

Other error. Contact Epson as described on page 89.

100 Monitoring the Projector Over a Network

Using E-mail Alerts

You can set up e-mail alerts to warn you of problems with the projector.

1. Open EMP Monitor.

2. From the Tool menu, select Mail notification function.

3. Turn the Mail notification function setting On.

4. Enter the IP address and port number of your networks SMTP (outgoing) mail server.

5. Enter the Sender (projector) mail address.

6. Enter up to three e-mail addresses to send alerts to in the Recipient mail address boxes.

7. Click the Notification event buttons to select the conditions under which an e-mail alert will be sent.

8. When youre done, click the OK button.

If a projector experiences a problem, EMP Monitor sends an e-mail message to each of the addresses you entered in the Set mail notification function window. The subject line and body of the message includes the projectors name and the warning or error (similar to the those listed on page 97).

When the problem has been fixed, EMP Monitor sends a message indicating the problem has been resolved.

note You can also set e-mail alerts from the projectors menu system (see page 95).

note If a projector develops a critical problem, it may not be possible for it to report the error.

Monitoring the Projector Over a Network 101

Using a Browser to Monitor the Projector If your projector is connected to a network, you can use a standard web browser to monitor and control it. When using a browser to access the projector, you cannot connect through a proxy server.

1. Make sure that the projector is connected to your network, as described on page 93.

2. Follow the instructions on page 58 to set Standby Mode to Network On in the Extended menu so you can monitor the projector in standby mode.

3. Open your web browser and enter the IP address of the projector you want to monitor in the browser window.

If youre not sure what the address of the projector is, turn the projector on and select Wired LAN from the Network menu to display the IP address of the projector. See page 94.

You see a login screen.

4. Do one of the following:

If you didnt set a Web Control Password in the Network menu, click OK.

If you set a Web Control password in the Network menu, enter it in the Password box, then click OK.

You see a screen displaying the settings you can change.

5. Select one of the menu options, then change any settings as needed. These settings correspond to those found in the projectors menu system. See page 50 for details.

You cannot change the Users Logo, High Altitude Mode, and Language settings in the Extended menu or select the Reset All and Reset Lamp Hours in the Reset menu

Use the controls at the bottom of the screen to choose a source, stop the action, turn off the picture and sound, or turn the projectors power on or off.

102 Monitoring the Projector Over a Network

A

103

A

Technical Specifications General

Type of display Poly-silicon TFT active matrix

Lens F=1.6 to 1.74, 18.4 to 22.12 mm

Resolution 1024 768 pixels (XGA)

Color reproduction Full color, 16.77 million colors

Brightness (ANSI) PowerLite 822+ 2600 lumens (High brightness mode)

2080 lumens (Low brightness mode)

Brightness (ANSI) PowerLite 83+ 2200 lumens (High brightness mode)

1760 lumens (Low brightness mode)

Contrast ratio 400:1

Image size 30 to 300 inches (0.8 to 7.6 meters)

Projection distance 2.7 to 34 feet (0.9 to 10.4 meters)

Projection methods Front, rear, ceiling

Focus adjustment Manual

Zoom adjustment Manual

Internal sound system 10 W monaural

Optical aspect ratio 4:3 (horizontal:vertical)

Zoom ratio 1:1.2

104 Technical Specifications

Noise level 35 dB (High brightness mode) 28 dB (Low brightness mode)

Keystone correction angle 30 vertical (maximum)

Projection Lamp

Power consumption 170 W UHE

Lamp life About 3000 hours (High brightness); 4000 hours (Low brightness)

Remote Control

Range 20 feet (6 meters)

Batteries (2) Alkaline AA

Dimensions

Height (including feet) 4.3 inches (108 mm)

Width 12.9 inches (327 mm)

Depth 9.6 inches (245 mm)

Weight 6.4 lb (2.9 kg)

Electrical

Rated frequency 50/60 Hz

Power supply 100 to 120 VAC, 2.8 A 200 to 240 VAC, 1.2 A

Power consumption Operating: 248 W Standby: 4.1 W (network off) 5 W (network on)

note Lamp life results will vary depending upon mode selected, environmental conditions and usage. Lamp brightness decreases over time.

Technical Specifications 105

Environmental

Temperature Operating: 41 to 95 F (5 to 35 C) Storage: 14 to 140 F (10 to 60 C)

Humidity Operating: 20 to 80% RH, non-condensing

Storage: 10 to 90% RH, non-condensing

Altitude Up to 4,900 feet (1,500 m) Up to 7,500 feet (2,286 m) with High Altitude Mode enabled; see page 58

Safety and Approvals

United States FCC Part15B Class B (DoC) UL60950-1

Canada ICES-003 Class B CSA C22.2 No. 60950-1

Pixelworks DNX ICs are used in this projector.

106 Technical Specifications

Compatible Video Formats

You can use any of the following video sources: VCR, DVD player, camcorder, digital camera, or gaming console. The projector supports composite video, S-Video, component video, and RGB video, and it automatically senses the video format (HDTV, SDTV, NTSC, PAL, or SECAM).

The projector supports these international video standards:

Mode Refresh Rate (Hz)

NTSC NTSC 4:3 PAL M-PAL N-PAL PAL60 SECAM

60 60 50 60 50 60 50

TV525i TV625i SDTV (480p and 480i) SDTV (576p and 576i) HDTV720p HDTV720p HDTV1080i HDTV1080i

60 50 60 50 60 50 60 50

Technical Specifications 107

Compatible Computer Display Formats

You can connect the projector to a wide range of computers, including PCs and notebooks, Apple Macintosh, PowerPC and Intel Core Macintosh computers, PowerBook computers, many iMac and iBook series systems, and high-end workstations such as the Sun SPARCstation.

Although images are displayed at the projectors native resolution of 1024 768 pixels, Epsons patented SizeWise chip supports computer display formats ranging from VGA through UXGA.

To project images output from a computer, the computers external monitor signal must be set at a refresh rate (vertical frequency) thats compatible with the projector; see the following table for compatible formats. For best results, the computers resolution should be set to match the projectors native resolution (1024 768). If this resolution isnt available, select one of the other compatible formats:

Windows: Right-click the desktop, select Properties, click the Settings tab, and select a compatible resolution. (For a notebook displaying through an external monitor port, youll need to click the Advanced button on the Settings tab, then adjust the resolution of the external monitor.)

Macintosh OS X: From the Apple menu, select System Preferences, then click Displays. Make sure the VGA Display or Color LCD dialog box is selected, then click the Display tab and select a compatible resolution.

You may need to modify existing presentation files if you created them for a different resolution. See your software documentation for details.

108 Technical Specifications

The projector supports these monitor display formats:

Mode Refresh Rate (Hz) Resolution

VGA EGA 70 640 350

VGA60 VESA72 VESA75 VESA85 VGA120

60 72 75 85 120

640 480 640 480 640 480 640 480 640 480

SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 SVGA120

56 60 72 75 85 120

800 600 800 600 800 600 800 600 800 600 800 600

XGA60 XGA70 XGA75 XGA85 XGA120

60 70 75 85 120

1024 768 1024 768 1024 768 1024 768 1024 768

SXGA170 SXGA175 SXGA185 SXGA1100

70 75 85 120

1152 864 1152 864 1152 864 1024 768

SXGA260 SXGA275 SXGA285

60 75 85

1280 960 1280 960 1280 960

SXGA360 SXGA375 SXGA385

60 75 85

1280 1024 1280 1024 1280 1024

SXGA+60 SXGA+75 SXGA+85

60 75 85

1400 1024 1400 1024 1400 1024

UXGA60 60 1600 1200

Technical Specifications 109

iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC1960 MAC19 MAC21

117 95 75 67 75 59 75 75

640 480 800 600 1024 768 640 480 832 624 1024 768 1024 768 1152 870

SDTV 480i SDTV (576i) SDTV (480p) SDTV (576p)

60 50 60 50

720 480 720 576 720 480 720 576

HDTV (720p) HDTV (1080i)

50/60 50/60

1280 720 1920 1080

Mode Refresh Rate (Hz) Resolution

110 Technical Specifications

B

111

B

Notices This chapter includes safety instructions and other important information about your PowerLite projector.

Important Safety Instructions Follow these safety instructions when setting up and using the projector:

Do not place the projector on an unstable cart, stand, or table.

Do not use the projector near water or sources of heat.

Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.

Place the projector near a wall outlet where the plug can be easily unplugged.

Insert the projectors two-prong plug into a properly grounded outlet. Do not hold the plug with wet hands.

Take the following precautions for the plug. Failure to comply with these precautions could result in sparks or fire: Do not insert the plug into an outlet with dust present. Insert the plug firmly into the outlet.

Do not overload wall outlets, extension cords, or integral convenience receptacles. This can cause fire or electric shock.

Do not place the projector where the cord can be walked on. This may result in fraying or damage to the plug.

Unplug the projector from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners.

Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or in a closed-in cabinet unless proper ventilation is provided.

Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector.

112 Notices

Except as specifically explained in this Users Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.

Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power cord or plug is damaged or frayed. If liquid has been spilled into the projector, or if it has been exposed to rain or water. If it does not operate normally when you follow the operating instructions, or if it exhibits a distinct change in performance, indicating a need for service. If it has been dropped or the housing has been damaged.

The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

Unplug the projector during lightning storms or when it will not be used for extended periods.

Do not place the projector and/or remote control on top of heat-producing equipment or in a hot location.

If you use the projector in a country other than where you purchased it, use the correct power cord for that country.

Do not stand on the projector or place heavy objects on it.

Do not use the projector outside of the required temperature range of 41 to 95 F (5 to 35 C). Doing so may cause an unstable display and could lead to projector damage.

Do not store the projector outside of the required temperature range of 14 to 140 F (10 to 60 C) or in direct sunlight for long periods of time. Doing so may cause damage to the case.

WARNING: The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. (provided in accordance with Proposition 65 in Cal. Health & Safety Code 25249.5 et seq).

Notices 113

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment.

For Canadian Users

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le materiel brouilleur du Canada.

114 Notices

Index 115

Index

A A/V cable, 24 to 25 A/V Mute, 46, 59, 64 to 65, 82, 87 Accessories, 14, 90 Adapter, Macintosh, 19 Air filter

cleaning and replacing, 72 to 74 purchasing, 14

Altitude, 59, 105 Anti-theft device, 14 Aspect button, 47 Aspect ratio, 47, 56, 103 Aspect setting, 56 Audio

adjusting volume, 41, 57 cable, 22, 87 connecting laptop, 22 problems, troubleshooting, 87 turning off, 46

Auto button, 41, 55 Auto Keystone correction, 17, 40, 50, 57 Auto Setup setting, 41, 55

B Background Color setting, 59, 66 Banding in image, 86 Batteries, replacing, 48 Blackboard color mode, 45, 53 Blank screen, 36 to 37, 82 to 83 Blue background, 59 Blurry image, 85 Brightness, 74, 103 Brightness Control setting, 40, 82 Brightness setting, 40, 53, 82, 86 Browser, monitoring projector with, 101 Buttons, disabling projector, 57, 68

C Cables, 11 to 14, 90 Camcorder, connecting to, 24 to 31 Carrying case, optional, 78 Ceiling

mount, 14, 17 projection, 17, 59

Cleaning air filter and vents, 72 to 74 lens, 72 projector case, 72

Color adjusting, 45, 52 to 54 problems, 86 specifications, 103

Color Adjustment setting, 54 Color Mode, 45, 53 Color Saturation setting, 53 Component-to-VGA video cable, 13 to 14, 24,

28 Composite video cable, 24 to 25 Computer

cable, 11, 18 to 20 connecting to projector, 18 to 22 source, selecting, 19, 20, 36, 44, 55 support, 7 supported display formats, 107 to 109

Computer/Component Video ports, 19 to 20, 27, 44

Connecting projector to a computer, 18 to 22 to a game console, 24 to 31 to a video source, 24 to 31 to external monitor, 21 to speakers, 23, 31

Contrast, 103 Contrast setting, 53, 86

116 Index

D Default password, 63 Default settings, restoring, 69 Digital camera, connecting to, 24 to 31 Dimensions, 104 Direct Power On setting, 59 Distance from projector to screen, 16, 103 Documentation, using, 9 DVD player, connecting to, 24 to 31

E E-mail alerts, 95 to 96, 100 EMP Monitor

monitoring the projector, 96 to 100 problems, 89 using, 96 to 100

Entering the password, 67 Environmental specifications, 105 Epson

accessories, 14, 90 Extra Care Road Service, 10 PrivateLine Support, 9, 90 Store, 90 technical support, 9, 89 to 90

Ethernet connection, 93 Extended menu, 50, 58 to 60 External monitor, connecting, 21 Extra Care Road Service, 10 E-Zoom button, 47

F FCC compliance statement, 113 Filter, cleaning and replacing, 72 to 74 Focusing, 38 Foot release lever, 39 Freeze button, 46 Front projection, 16 to 17, 59 Front/Ceiling setting, 17, 59 Full Lock setting, 57, 68

G Game color mode, 45, 53 Game console, connecting to, 24 to 31

H Height of image, adjusting, 39 Help, 9, 89 to 90 Help system, using, 80 High Altitude Mode setting, 59, 105 High brightness, 40, 74, 82, 103

I iBook, connecting to, 18 to 19 iMac, connecting to, 13, 18 to 20 Image

capturing and saving in projector, 64 to 65 correcting shape of, 40, 57, 84 fitting on screen, 41, 55, 56, 84 focusing, 38 freezing, 46 height, adjusting, 39 menu, 50, 52 to 54 positioning, 39, 41, 55 problems, 82 to 86 raising, 39 selecting source, 19, 20, 25, 35, 36, 44,

55 to 56 shape, correcting, 40, 57, 84 size and projection distance, 16, 103 turning off, 46 zooming, 47

Info menu, 50, 61 to 62 Input signal, selecting, 19, 20, 25 to 28, 36,

44, 55 to 56 Installing software, 92 Instant Off feature, 42

K Kensington anti-theft device, 14 Keystone correction, 40, 57, 84, 104

Index 117

L Lamp

automatic shutoff, 42 brightness, 74, 82, 103 number of hours used, 61, 74, 77, 104 replacing, 74 to 77 specifications, 104 status light, 80 to 81 timer, resetting, 77

Language setting, 60 Laptop computer

connecting to, 18 to 20 displaying on, 36 to 37, 83

LCD panels, 7 Lens

cleaning, 72 specifications, 103

Lights, status, 80 to 81 Logo

creating, 64 to 65 displaying, 65 to 66 turning on, 59, 66

Low brightness, 40, 74, 103

M Macintosh

adapter, 19 connecting, 18 to 20

Manuals, 9 Menus

changing settings, 51 to 52 Extended, 50, 58 to 60 Image, 50, 52 to 54 Info, 50, 61 to 62 Network, 50, 60, 94 to 96 Reset, 50, 69 Settings, 50, 56 to 57 Signal, 50, 54 to 56 Users Logo, 64 to 65 using, 50 to 52

Messages setting, 58 Monitor, external, 21

Monitoring projector e-mail notifications, 95 to 96, 100 EMP Monitor, 96 to 100 with browser, 101

Moving projector, 78

N Network

connecting to, 93 managing projector remotely, 91 to 101 menu, 50, 60, 94 to 96 problems, 89 settings, 60, 94 to 96, 97 system requirements, 92

Network Protect password, 66 Noise level, 104

O Operation Lock setting, 57, 68 Options for projector, 14, 90

P Password

default, 63 entering, 67 logo protection, 64 to 67 Network Protect, 66 problems, 87 prompt, 35, 67 request code, 67 setting, 65 to 66 turning on, 66

Photo color mode, 45, 53 Picture source, selecting, 19, 20, 25 to 28, 36,

55 to 56 Pixelworks, 105 Position setting, 55 Positioning

image, 39, 55 projector, 16 to 17

118 Index

Power button, 35, 42 consumption, 104 light, 35, 80 to 81 supply, 104

PowerBook, connecting to, 18 to 20 Presentation color mode, 45, 53 Presenters Online, 9 PrivateLine Support, 9, 90 Problems

color, 86 image, 82 to 86 monitoring projector, 89 network, 89 password, 87 remote control, 88 sound, 87

Projection lamp, see Lamp Projector

accessories, 14, 90 carrying case, optional, 78 cleaning, 71 to 74 disabling buttons, 57, 68 distance from screen, 16, 103 foot, adjusting height with, 39 lamp specifications, 104 monitoring remotely, 91 to 101 password protection, 62 to 67 positioning, 16 to 17 resolution, 7, 103, 107 to 109 transporting, 78 turning off, 42 turning on, 34 to 35 unpacking, 11 viewing information about, 61 to 62

Q Quick Setup sheet, 9

R Raising image, 39 RCA A/V cable, 24 to 25 Rear projection, 17, 59

Registration, 10 Remote control

problems, 88 receivers, disabling, 57, 82, 88 replacing, 14, 90 replacing batteries, 48 specifications, 104 using, 43 to 48

Remote Receiver setting, 57, 82, 88 Replacing

air filter, 72 to 74 lamp, 74 to 77 remote control, 14, 90 remote control batteries, 48

Request code, password, 67 Reset menu, 50, 69 Resolution, 7, 61, 103, 107 to 109

S Safety

approvals, 105 instructions, 111 to 112

Screen logo, see Users Logo Screen, distance from projector, 16, 103 Screens, portable, 14 Setting a password, 65 to 66 Settings menu, 50, 56 to 57 Sharpness setting, 54 Signal menu, 50, 54 to 56 Sleep mode, 42, 59 Software installation, 92 Sound, see Audio Source Search button, 19 to 20, 25 to 28,

35 to 36, 44 Speaker, specifications, 103 Speakers, connecting external, 23, 31 Specifications, technical, 103 to 109 Sports color mode, 45, 53 sRGB color mode, 45, 53 Standby Mode setting, 60, 97 Startup screen

creating, 64 to 65 displaying, 65 to 66 users logo, see Users Logo

Index 119

Startup Screen setting, 59 Status lights, 80 to 81 Stopping action, 46 Stripes in image, 86 Support, 9, 89 to 90 S-Video cable, 13, 14, 24 Switching picture source, 36, 44 Sync, adjusting, 55, 85 to 86 System requirements, network, 92

T Technical support, 9, 89 to 90 Temperature

light, 80 to 81 requirements, 105

Test Pattern setting, 57 Text color mode, 45 Theatre color mode, 45, 53 Timer, lamp, 77 Tint setting, 54 Tracking, adjusting, 55, 85 to 86 Transporting projector, 78 Troubleshooting

color, 86 cut-off image, 41, 84 image quality, 85 to 86 image shape, 84 network problems, 89 no image, 82 to 83 no sound, 87 password, 87 remote control problems, 88

Turning off audio, 46 picture, 46 projector, 42

Turning on password, 66 projector, 34 to 35 Users Logo, 59, 66

Typing the password, 67

U Unpacking projector, 11 Users Logo

creating, 64 to 65 displaying, 65 to 66 turning on, 59, 66

V VCR, connecting to, 24 VGA computer cables, 11, 18 to 20 Video

display settings, 61 to 62 formats, supported, 7, 106 source, connecting to, 24 to 31 source, selecting, 25, 35 to 36, 44, 55 to 56

Video Signal setting, 56 Volume, adjusting, 41, 57

W Warning lights, 80 to 81 Warranty, 10 Weight, 104

Z Zoom ratio, 103 Zooming ima

Manualsnet FAQs

If you want to find out how the PowerLite 83+ Epson works, you can view and download the Epson PowerLite 83+ User's Guide on the Manualsnet website.

Yes, we have the User's Guide for Epson PowerLite 83+ as well as other Epson manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Guide should include all the details that are needed to use a Epson PowerLite 83+. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Epson PowerLite 83+ User's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Epson PowerLite 83+ User's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Epson PowerLite 83+ User's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Epson PowerLite 83+ User's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Epson PowerLite 83+ User's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.