Contents

Epson PowerLite Home Cinema 3000 Quick Setup PDF

1 of 4
1 of 4

Summary of Content for Epson PowerLite Home Cinema 3000 Quick Setup PDF

Quick Setup Before using the projector, make sure you read the safety instructions in the online Users Guide.

Note: These illustrations show the PowerLite Home Cinema 3600e, but the instructions are the same for the PowerLite Home Cinema 3000/3500/3510 unless otherwise noted.

Connect the projector Choose from the following connections. For additional connection types, see the online Users Guide.

Note: To access the rear ports on the PowerLite Home Cinema 3600e, remove the cable cover by using coins or your fingernails to lift up and out on the gaps at the bottom of the cable cover.

Video device Connect up to 4 video devices and use the Source buttons on the remote control or the button on the projector to switch between them.

Component video cable

RCA video cable

HDMI cable

Mobile media device (PowerLite Home Cinema 3500/3510/3600e) Connect tablets, smartphones, and other devices that support the MHL standard to the HDMI 1/MHL port using a MHL compatible cable.

MHL cable

Note: Some devices may require an adapter or may not require an MHL cable. Not all features or functions may be supported. Check your devices documentation for more information.

WirelessHD (PowerLite Home Cinema 3600e) Follow these steps to set up the included WirelessHD Transmitter.

1 Place the transmitter within 32 feet (10 m) of the projector. Make sure the front of the transmitter faces the front of the projector. See the online Users Guide for more information on the WirelessHD transmission range.

Note: Do not place the transmitter on a metal surface, as this may interfere with the signal. Make sure there are no obstructions between the transmitter and the projector.

2 Plug the AC adapter into the transmitter and a wall outlet.

3 Connect the HDMI cables to your video input devices and the HDMI ports on the side and back of the WirelessHD Transmitter. You can connect up to five input devices to the transmitter. See Viewing WirelessHD content for information on switching between input sources

Note: You can connect tablets, smartphones and other devices that support the MHL standard to the HDMI port on the side of the WirelessHD Transmitter. Some devices may require an adapter or may not require an MHL cable. Not all features or functions may be supported. Check your devices documentation for more information.

4 To use the transmitter as a pass-through device to a television or other display, connect an HDMI cable to the display device and the HDMI output port on the rear of the transmitter. See Viewing WirelessHD content for information on switching between wireless and wired display modes.

Connect audio Built-in speaker (PowerLite Home Cinema 3500/3510/3600e) The projector has a built-in speaker that can play audio from a connected video source (DVD player, streaming device, etc.) using an HDMI connection. If you do not use an HDMI connection, you can connect your devices audio output to the projectors audio input.

HDMI cable

Audio cable

Audio Out port (PowerLite Home Cinema 3500/3510/3600e) You can connect the projector to external self-powered speakers through the Audio Out port.

3.5 mm stereo mini cable

Note: You can also connect external self-powered speakers to the Optical Out port on the WirelessHD Transmitter (PowerLite Home Cinema 3600e).

External speakers Connect your devices audio output to your home theater receiver or powered speakers.

Note: When outputting sound through an external source, you may need to reduce the projector volume to zero or make sure that the correct audio output is selected on your device to prevent duplicate sound from being heard from the projector (PowerLite Home Cinema 3500/3510/3600e).

Home theater system

Video source

Surround sound Receiver Projector

Video cable

Powered speakers

External speakers Video source Projector

Video cable

Note: See your home theater receiver documentation for more information on connections.

Turn on your equipment 1 Turn on your video source.

2 Plug in the projector.

3 Remove the lens cap.

4 Press the power button on the projector or the On button on the remote control. The power light flashes blue, then stays on.

Note: To shut down the projector, press the power button on the projector or the Standby button on the remote control twice. You dont have to wait for the projector to cool down.

5 The default language of the menu system is English. To select another language, press the Menu button on the projector or remote control. Select Settings and press Enter. Select Language and press Enter. Select your language and press Enter. Press the Menu button to exit the menu system.

Adjust the image 1 If you dont see an image, press one of the Source buttons on the remote

control or the button on the projector to select the image source.

Note: If you still see a blank screen or have other display problems, see Troubleshooting.

2 For the best image quality, place the projector directly in front of the center of the screen, facing the screen squarely. If this is not possible, turn the horizontal and vertical lens shift dials to adjust the image position and center it on the screen.

3 If the image is tilted, adjust the front feet as shown below.

4 Turn the zoom ring to reduce or enlarge the image.

5 Turn the focus ring to sharpen the image.

6 If your image is uneven on the sides, you can use the keystone correction feature to adjust the image. To use this feature, you must first set the lens to the center-top position using the lens shift dials.

Press the or buttons to display the keystone correction screen. Then press the , , , or buttons to correct for horizontal and vertical keystone distortion.

PowerLite Home Cinema 3000/3500/3510/3600e

4127732 Rev.0 1-F C

4127732 Rev.0 1-F M

4127732 Rev.0 1-F Y

4127732 Rev.0 1-F K

Quick Setup Before using the projector, make sure you read the safety instructions in the online Users Guide.

Note: These illustrations show the PowerLite Home Cinema 3600e, but the instructions are the same for the PowerLite Home Cinema 3000/3500/3510 unless otherwise noted.

Connect the projector Choose from the following connections. For additional connection types, see the online Users Guide.

Note: To access the rear ports on the PowerLite Home Cinema 3600e, remove the cable cover by using coins or your fingernails to lift up and out on the gaps at the bottom of the cable cover.

Video device Connect up to 4 video devices and use the Source buttons on the remote control or the button on the projector to switch between them.

Component video cable

RCA video cable

HDMI cable

Mobile media device (PowerLite Home Cinema 3500/3510/3600e) Connect tablets, smartphones, and other devices that support the MHL standard to the HDMI 1/MHL port using a MHL compatible cable.

MHL cable

Note: Some devices may require an adapter or may not require an MHL cable. Not all features or functions may be supported. Check your devices documentation for more information.

WirelessHD (PowerLite Home Cinema 3600e) Follow these steps to set up the included WirelessHD Transmitter.

1 Place the transmitter within 32 feet (10 m) of the projector. Make sure the front of the transmitter faces the front of the projector. See the online Users Guide for more information on the WirelessHD transmission range.

Note: Do not place the transmitter on a metal surface, as this may interfere with the signal. Make sure there are no obstructions between the transmitter and the projector.

2 Plug the AC adapter into the transmitter and a wall outlet.

3 Connect the HDMI cables to your video input devices and the HDMI ports on the side and back of the WirelessHD Transmitter. You can connect up to five input devices to the transmitter. See Viewing WirelessHD content for information on switching between input sources

Note: You can connect tablets, smartphones and other devices that support the MHL standard to the HDMI port on the side of the WirelessHD Transmitter. Some devices may require an adapter or may not require an MHL cable. Not all features or functions may be supported. Check your devices documentation for more information.

4 To use the transmitter as a pass-through device to a television or other display, connect an HDMI cable to the display device and the HDMI output port on the rear of the transmitter. See Viewing WirelessHD content for information on switching between wireless and wired display modes.

Connect audio Built-in speaker (PowerLite Home Cinema 3500/3510/3600e) The projector has a built-in speaker that can play audio from a connected video source (DVD player, streaming device, etc.) using an HDMI connection. If you do not use an HDMI connection, you can connect your devices audio output to the projectors audio input.

HDMI cable

Audio cable

Audio Out port (PowerLite Home Cinema 3500/3510/3600e) You can connect the projector to external self-powered speakers through the Audio Out port.

3.5 mm stereo mini cable

Note: You can also connect external self-powered speakers to the Optical Out port on the WirelessHD Transmitter (PowerLite Home Cinema 3600e).

External speakers Connect your devices audio output to your home theater receiver or powered speakers.

Note: When outputting sound through an external source, you may need to reduce the projector volume to zero or make sure that the correct audio output is selected on your device to prevent duplicate sound from being heard from the projector (PowerLite Home Cinema 3500/3510/3600e).

Home theater system

Video source

Surround sound Receiver Projector

Video cable

Powered speakers

External speakers Video source Projector

Video cable

Note: See your home theater receiver documentation for more information on connections.

Turn on your equipment 1 Turn on your video source.

2 Plug in the projector.

3 Remove the lens cap.

4 Press the power button on the projector or the On button on the remote control. The power light flashes blue, then stays on.

Note: To shut down the projector, press the power button on the projector or the Standby button on the remote control twice. You dont have to wait for the projector to cool down.

5 The default language of the menu system is English. To select another language, press the Menu button on the projector or remote control. Select Settings and press Enter. Select Language and press Enter. Select your language and press Enter. Press the Menu button to exit the menu system.

Adjust the image 1 If you dont see an image, press one of the Source buttons on the remote

control or the button on the projector to select the image source.

Note: If you still see a blank screen or have other display problems, see Troubleshooting.

2 For the best image quality, place the projector directly in front of the center of the screen, facing the screen squarely. If this is not possible, turn the horizontal and vertical lens shift dials to adjust the image position and center it on the screen.

3 If the image is tilted, adjust the front feet as shown below.

4 Turn the zoom ring to reduce or enlarge the image.

5 Turn the focus ring to sharpen the image.

6 If your image is uneven on the sides, you can use the keystone correction feature to adjust the image. To use this feature, you must first set the lens to the center-top position using the lens shift dials.

Press the or buttons to display the keystone correction screen. Then press the , , , or buttons to correct for horizontal and vertical keystone distortion.

PowerLite Home Cinema 3000/3500/3510/3600e

4127732 Rev.0 1-F C

4127732 Rev.0 1-F M

4127732 Rev.0 1-F Y

4127732 Rev.0 1-F K

If 3D images arent displaying properly, check the following:

Press the 3D Format button to switch to 3D viewing mode, if necessary.

Make sure to wear the 3D glasses within 32 feet (10 m) of the projector.

Check that your 3D glasses have not entered standby mode. Slide the power switch on the 3D glasses into the Off position, then back to the On position.

Press the Menu button on your remote control, select the Signal menu, then 3D Setup, then select 3D Format. Make sure that the Auto option is selected. You may also need to set the 3D Depth and Diagonal Screen Size setting in the Signal menu. See the online Users Guide for more information.

Check that your video device and media are both 3D-compatible. Refer to the documentation that came with your video device for more information.

If WirelessHD content isnt displaying properly, check the following:

Check that the Link light on the transmitter is lit. If the light is flashing slowly, the transmitter could not connect with the projector and has entered standby mode. Verify that the projector is turned on and that all cables are properly connected as shown in the Connect the projector section. You may also need to press the Input button several times before the Link light turns on.

Make sure the WirelessHD Transmitter is within 32 feet (10 m) of the projector, is facing the front of the projector, isnt obstructed by any large objects, and is not placed on a metal surface.

If you are viewing wireless content, make sure that the WiHD light on the transmitter is lit. If it isnt, press the Output button on the remote control or transmitter.

If the keystone correction feature doesnt correct the image, make sure you first set the lens to the center-top position using the horizontal and vertical lens shift dials.

Where to get help Manuals For more information about using the projector, click the icons on your desktop to access the online manuals (requires an Internet connection). If you dont have icons to the manuals, you can install them from the projector CD or go to the Epson website, as described below.

Telephone support services To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a support specialist by calling (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).

Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Internet support Visit epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson.

Registration Register today to get product updates and exclusive offers. You can use the CD included with your projector or register online at epson.com/webreg.

Optional accessories For a list of optional accessories, see the online Users Guide.

You can purchase RF 3D glasses (part number V12H548006) or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).

Using the remote control Make sure the batteries are installed as shown (two AA batteries).

Choose which source to display

Turn projector on

Access projector menus

Navigate projector menus

Turn projector off

Switch between 2D and 3D

Control WirelessHD functions (PowerLite Home Cinema

3600e only)

For more information on using the remote control, see the online Users Guide.

Viewing 3D images To view 3D content, you must first connect a 3D-compatible video device to one of the HDMI ports on your projector. You will also need a pair of Epson (part number V12H548006) or Epson-compatible RF 3D active shutter glasses (included with PowerLite Home Cinema 3500/3510/3600e).

1 Turn on and begin playback on the 3D-compatible video device.

Note: Make sure you set the video device to play content in 3D mode.

2 Press the 3D Format button on the remote control, if necessary.

3 Slide the power switch on your 3D glasses to the On position.

Note: If the glasses dont automatically display 3D content, you may need to pair them with the projector. Move the glasses within 10 feet (3 m) of the projector, then press and hold the Pairing button on the 3D glasses for at least 3 seconds. The status light on the glasses will alternately flash green and red, then remain green for 10 seconds if pairing is successful.

EPSON and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.

Mac is a trademark of Apple Inc., registered in the U.S. and other countries.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

2014 Epson America, Inc., 7/14 Printed in XXXXXX CPD-41443

You can also automatically convert 2D HDMI content to 3D (PowerLite Home Cinema 3500/3510/3600e). To enable the 2D-to-3D Conversion option, press the Menu button on the projector or remote control. Select Signal and press Enter, then select 3D Setup and press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak, Medium, or Strong setting, then press Enter.

See the online Users Guide for more information on adjusting 3D images.

Viewing WirelessHD content (PowerLite Home Cinema 3600e) 1 Turn on your video device and begin playback.

2 Turn on the power switch on the side of the WirelessHD Transmitter.

3 Turn on the projector.

4 If you have connected a television or other display to the output port on the transmitter and want to switch between wired and wireless display modes, press the Output button on the remote control or transmitter. The WiHD light on the transmitter will light up when the wireless display mode is active.

5 Press the WirelessHD button on the remote control.

Note: If the WirelessHD connection fails, press the Setup button on the bottom of the transmitter, then try again.

6 If you have connected multiple input devices to the transmitter, press the Input button on the remote control or transmitter once to display the sub-screen menu, then press the button again to switch between the input devices.

7 To display two WirelessHD input devices simultaneously, press the P-in-P button on the remote control to enable picture-in-picture mode. Press and hold the P-in-P button for three seconds to switch the main image and sub-screen, or press the P-in-P button again to disable picture-in-picture mode.

See the online Users Guide for more information on adjusting and configuring the WirelessHD connection and display modes.

Troubleshooting If you see a blank screen or the No signal message after turning on your video device or computer, check the following:

Make sure the power light on the projector is blue and not flashing.

Press the button on the projector or one of the Source buttons on the remote control to switch to the correct image source, if necessary.

If youre using a Windows laptop, press the function key on your keyboard that lets you display on an external monitor. It may be labeled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it (such as Fn + F7). Wait a moment for the display to appear.

If youre using a Mac laptop, open System Preferences and select Displays. Click the Arrangement tab and select the Mirror Displays checkbox.

Notices Bluetooth Safety and Specifications Contains Bluetooth module model: DBUB-E207

This document provides safety instructions and describes the specifications. Read this document carefully before use to ensure your safety and product performance.

U.S.

FCC Notices

Contains FCC ID: BKMAE-E207

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Properly shielded cables must be used for connections to LCD Projector in order to meet FCC emission limits. The cable for peripheral with a ferrite core must be used for RF interference suppression.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Canada

Industry Canada (IC) Notices

Contains IC: 1052D-E207

This Class B digital apparatus complies with Canadian ICES-003.

CAN ICES-3(B)/NMB-3(B)

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

4127732 Rev.0 1-B C

4127732 Rev.0 1-B M

4127732 Rev.0 1-B Y

4127732 Rev.0 1-B K

If 3D images arent displaying properly, check the following:

Press the 3D Format button to switch to 3D viewing mode, if necessary.

Make sure to wear the 3D glasses within 32 feet (10 m) of the projector.

Check that your 3D glasses have not entered standby mode. Slide the power switch on the 3D glasses into the Off position, then back to the On position.

Press the Menu button on your remote control, select the Signal menu, then 3D Setup, then select 3D Format. Make sure that the Auto option is selected. You may also need to set the 3D Depth and Diagonal Screen Size setting in the Signal menu. See the online Users Guide for more information.

Check that your video device and media are both 3D-compatible. Refer to the documentation that came with your video device for more information.

If WirelessHD content isnt displaying properly, check the following:

Check that the Link light on the transmitter is lit. If the light is flashing slowly, the transmitter could not connect with the projector and has entered standby mode. Verify that the projector is turned on and that all cables are properly connected as shown in the Connect the projector section. You may also need to press the Input button several times before the Link light turns on.

Make sure the WirelessHD Transmitter is within 32 feet (10 m) of the projector, is facing the front of the projector, isnt obstructed by any large objects, and is not placed on a metal surface.

If you are viewing wireless content, make sure that the WiHD light on the transmitter is lit. If it isnt, press the Output button on the remote control or transmitter.

If the keystone correction feature doesnt correct the image, make sure you first set the lens to the center-top position using the horizontal and vertical lens shift dials.

Where to get help Manuals For more information about using the projector, click the icons on your desktop to access the online manuals (requires an Internet connection). If you dont have icons to the manuals, you can install them from the projector CD or go to the Epson website, as described below.

Telephone support services To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a support specialist by calling (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).

Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Internet support Visit epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson.

Registration Register today to get product updates and exclusive offers. You can use the CD included with your projector or register online at epson.com/webreg.

Optional accessories For a list of optional accessories, see the online Users Guide.

You can purchase RF 3D glasses (part number V12H548006) or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).

Using the remote control Make sure the batteries are installed as shown (two AA batteries).

Choose which source to display

Turn projector on

Access projector menus

Navigate projector menus

Turn projector off

Switch between 2D and 3D

Control WirelessHD functions (PowerLite Home Cinema

3600e only)

For more information on using the remote control, see the online Users Guide.

Viewing 3D images To view 3D content, you must first connect a 3D-compatible video device to one of the HDMI ports on your projector. You will also need a pair of Epson (part number V12H548006) or Epson-compatible RF 3D active shutter glasses (included with PowerLite Home Cinema 3500/3510/3600e).

1 Turn on and begin playback on the 3D-compatible video device.

Note: Make sure you set the video device to play content in 3D mode.

2 Press the 3D Format button on the remote control, if necessary.

3 Slide the power switch on your 3D glasses to the On position.

Note: If the glasses dont automatically display 3D content, you may need to pair them with the projector. Move the glasses within 10 feet (3 m) of the projector, then press and hold the Pairing button on the 3D glasses for at least 3 seconds. The status light on the glasses will alternately flash green and red, then remain green for 10 seconds if pairing is successful.

EPSON and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.

Mac is a trademark of Apple Inc., registered in the U.S. and other countries.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

2014 Epson America, Inc., 7/14 Printed in XXXXXX CPD-41443

You can also automatically convert 2D HDMI content to 3D (PowerLite Home Cinema 3500/3510/3600e). To enable the 2D-to-3D Conversion option, press the Menu button on the projector or remote control. Select Signal and press Enter, then select 3D Setup and press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak, Medium, or Strong setting, then press Enter.

See the online Users Guide for more information on adjusting 3D images.

Viewing WirelessHD content (PowerLite Home Cinema 3600e) 1 Turn on your video device and begin playback.

2 Turn on the power switch on the side of the WirelessHD Transmitter.

3 Turn on the projector.

4 If you have connected a television or other display to the output port on the transmitter and want to switch between wired and wireless display modes, press the Output button on the remote control or transmitter. The WiHD light on the transmitter will light up when the wireless display mode is active.

5 Press the WirelessHD button on the remote control.

Note: If the WirelessHD connection fails, press the Setup button on the bottom of the transmitter, then try again.

6 If you have connected multiple input devices to the transmitter, press the Input button on the remote control or transmitter once to display the sub-screen menu, then press the button again to switch between the input devices.

7 To display two WirelessHD input devices simultaneously, press the P-in-P button on the remote control to enable picture-in-picture mode. Press and hold the P-in-P button for three seconds to switch the main image and sub-screen, or press the P-in-P button again to disable picture-in-picture mode.

See the online Users Guide for more information on adjusting and configuring the WirelessHD connection and display modes.

Troubleshooting If you see a blank screen or the No signal message after turning on your video device or computer, check the following:

Make sure the power light on the projector is blue and not flashing.

Press the button on the projector or one of the Source buttons on the remote control to switch to the correct image source, if necessary.

If youre using a Windows laptop, press the function key on your keyboard that lets you display on an external monitor. It may be labeled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it (such as Fn + F7). Wait a moment for the display to appear.

If youre using a Mac laptop, open System Preferences and select Displays. Click the Arrangement tab and select the Mirror Displays checkbox.

Notices Bluetooth Safety and Specifications Contains Bluetooth module model: DBUB-E207

This document provides safety instructions and describes the specifications. Read this document carefully before use to ensure your safety and product performance.

U.S.

FCC Notices

Contains FCC ID: BKMAE-E207

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Properly shielded cables must be used for connections to LCD Projector in order to meet FCC emission limits. The cable for peripheral with a ferrite core must be used for RF interference suppression.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Canada

Industry Canada (IC) Notices

Contains IC: 1052D-E207

This Class B digital apparatus complies with Canadian ICES-003.

CAN ICES-3(B)/NMB-3(B)

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an unc

Manualsnet FAQs

If you want to find out how the PowerLite Home Cinema 3000 Epson works, you can view and download the Epson PowerLite Home Cinema 3000 Quick Setup on the Manualsnet website.

Yes, we have the Quick Setup for Epson PowerLite Home Cinema 3000 as well as other Epson manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Quick Setup should include all the details that are needed to use a Epson PowerLite Home Cinema 3000. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Epson PowerLite Home Cinema 3000 Quick Setup is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Epson PowerLite Home Cinema 3000 Quick Setup consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Epson PowerLite Home Cinema 3000 Quick Setup free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Epson PowerLite Home Cinema 3000 Quick Setup, simply download the document to your computer. Once downloaded, open the PDF file and print the Epson PowerLite Home Cinema 3000 Quick Setup as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.